Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separated Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Control of Flow Separation Using Adaptive Airfoils

A novel way of controlling flow separation is reported. The approach involves using an adaptive airfoil geometry that changes its leading edge shape to adjust to the instantaneous flow at high angles of attack such that the flow over it remains attached. In particular, a baseline NACA 0012 airfoil, whose leading edge curvature could be changed dynamically by 400% was tested under quasi-steady compressible flow conditions. A mechanical drive system was used to produce a rounded leading edge to reduce the strong local flow acceleration around its nose and thus reduce the strong adverse pressure gradient that follows such a rapid acceleration. Tests in steady flow showed that at M = 0.3, the flow separated at about 14 deg. angle of attack for the NACA 0012 profile but could be kept attached up to an angle of about 18 deg by changing the nose curvature. No significant hysteresis effects were observed; the flow could be made to reattach from its separated state at high angles by changing the leading edge curvature.

Chandrasekhara, M. S.↗
NASA NTRS2015

Implicit LES of Turbulent, Separated Flow: Wall-Mounted Hump Configuration

Direct simulations (ILES) of turbulent, separated flow over the wall-mounted hump configuration is conducted to investigate the physics of separated flows. A chord-based Reynolds number of Re(sub c) = 47,500 is set up, with a turbulent in flow of Re(sub theta) = 1,400 (theta/c = 3%). FDL3DI, a code that solves the compressible Navier-Stokes equations using high- order compact-difference scheme and filter, with the standard recycling/rescaling method of turbulence generation, is used. Two different configurations of the upper-wall are analyzed, and results are compared with both a higher Re(sub c) (= 936,000, Re(sub theta) = 7,200, theta/c = 0.77%) experiment for major flow features, and RANS (k-omega SST) results. A lower Rec allows for DNS-like mesh resolution, and an adequately wide span. Both ILES and RANS show delayed reattachment compared to experiment, and significantly higher skin friction in the forebody of the hump, as expected. The upper-wall shape influences the C(sub p) distribution only. Results from this study are being used to setup higher Rec (lower theta/c) ILES.

Implicit LES↗
NASA NTRS1975

Lip noise generated by flow separation from nozzle surfaces

The results of a series of experiments, performed to investigate flow separation and classic lip noise and to aid in understanding aeroacoustic noise generation are presented. Several types of nozzle-lip configurations were used to study the high frequency noise generated by small regions of flow separation at the nozzle lip. These included coaxial nozzles, and circular and slot nozzles with splitter plates. The jet flow velocity was varied and far field noise was measured for all nozzle-lip geometries (coaxial and splitter plate). The effect of a velocity difference across the lip of the coaxial nozzle and the splitter plate on the far field noise was also measured. Finally, an effort was made to find means to reduce the high frequency noise caused by flow separation at the lip.

Olsen, W.↗
NASA NTRS1978

A new boundary-layer interaction techniques for separated flows

A new viscous-inviscid interation procedure is presented which is applicable to separated flows. The new procedure is simple, converges rapidly, and does not require numerical smoothing and underrelaxation at least in the cases computer thus far. Calculations are presented for the low-speed separated flow in the juncture region between an axisymmetric body and ting. The viscous computation is done with an inverse boundary-layer procedure which was previously developed. The inviscid computation is made with an axisymmetric transonic code called RAXBOD. The main advantage of the new interaction procedure is that it combines an inverse boundary-layer technique, which is applicable to separated flows, with an existing inviscid analysis code with only a slight boundary condition change required in the inviscid code.

Carter, J. E.↗
NASA NTRS1984

Experimental studies of the separated flow over a NASA GA(W)-1 airfoil

The separated flow over the 17-percent-thick blunt-trailing-edge NASA GA(W)-1 airfoil is investigated experimentally at angles of attack 10.3-18.4 deg and velocities up to 92 m/sec in the 1.09 x 0.76 x 1.22-m working section of a closed-circuit wind tunnel, with typical Reynolds numbers of the order 4 x 10 to the 6th. The results are presented graphically and characterized. Separated-flow velocity profiles and skin-friction distributions are obtained, and the boundary-layer integral properties are shown to be in good agreement with the separation criteria of Sandborn and Kline (1961). The chordwise development of the mean velocity is reduced to a universal curve, and some similarity is found in the outer-region velocity profiles downstream of the separation.

Mehta, J. M.↗
NASA NTRS1951

Preliminary Investigation of Use of Conical Flow Separation for Efficient Supersonic Diffusion

Use of flow separation on a rod projecting upstream of a blunt body to decelerate the supersonic stream ahead of an annular nose inlet was investigated at Mach numbers of 1.76, 1.93, and 2.10. Maximum pressure recoveries were obtained with rod tip projections about 1.5 times the radius of the spherical nose and were higher than those obtained with single-shock solid cones. Subcritical operation was similar to that observed with solid-cone inlets, but the effect of angle of attack on maximum pressure recovery was more severe.

WIND TUNNEL TESTS - LFPL - SUPERSONIC (18"x18")↗
NASA NTRS2000

AST Critical Propulsion and Noise Reduction Technologies for Future Commercial Subsonic Engines: Separate-Flow Exhaust System Noise Reduction Concept Evaluation

This report describes the work performed by General Electric Aircraft Engines (GEAE) and Allison Engine Company (AEC) on NASA Contract NAS3-27720 AoI 14.3. The objective of this contract was to generate quality jet noise acoustic data for separate-flow nozzle models and to design and verify new jet-noise-reduction concepts over a range of simulated engine cycles and flight conditions. Five baseline axisymmetric separate-flow nozzle models having bypass ratios of five and eight with internal and external plugs and 11 different mixing-enhancer model nozzles (including chevrons, vortex-generator doublets, and a tongue mixer) were designed and tested in model scale. Using available core and fan nozzle hardware in various combinations, 28 GEAE/AEC separate-flow nozzle/mixing-enhancer configurations were acoustically evaluated in the NASA Glenn Research Center Aeroacoustic and Propulsion Laboratory. This report describes model nozzle features, facility and data acquisition/reduction procedures, the test matrix, and measured acoustic data analyses. A number of tested core and fan mixing enhancer devices and combinations of devices gave significant jet noise reduction relative to separate-flow baseline nozzles. Inward-flip and alternating-flip core chevrons combined with a straight-chevron fan nozzle exceeded the NASA stretch goal of 3 EPNdB jet noise reduction at typical sideline certification conditions.

Janardan, B. A.↗
NASA NTRS2018

A Numerical and Experimental Investigation of Flow Separation Control over a Wall-Mounted Hump Model

Numerical simulations and wind tunnel experiments were performed to investigate flow separation and its control over a wall-mounted hump model. Three-dimensional, unsteady fluid dynamic simulations were used to capture the relevant flow physics of unsteady flow separation and its control via active and passive flow control methods. Surface pressure measurements and surface oilflow visualization were obtained in the experiments. Current measurements documented a considerably thinner incoming boundary layer, but similar pressure distribution, compared to the reference data reported in the CFD (Computational Fluid Dynamics) Validation (CFDVAL 2004) Experiments. Consistent with the data available in the literature, numerical simulations predicted a longer separation bubble, which manifested itself as a shift in the pressure distributions. Streamwise vortices generated by passive vortex generators increased the suction pressure and provided substantial pressure recovery. Numerical simulations of vortex generators qualitatively predicted the effects of control, and revealed patterns of attached/separated flow regions. On the other hand, active flow control using steady discrete jets reduced, but was not able to eliminate, flow separation for the tested configuration. Although the major disagreement between the numerical and experimental results was in the pressure recovery region due to the inaccurate prediction of separation bubbles, the relative pressure recoveries from the baselines were comparable. Surface oilflow visualization and simulated surface streamlines were qualitatively in good agreement revealing the key flow features.

Koklu, Mehti↗
NASA NTRS1981

Oil-flow separation patterns on an ogive forebody

Oil flow patterns on a symmetric tangent ogive forebody having a fineness ratio of 3.5 are presented for angles of attack up to 88 deg at a transitional Reynolds number of 8 million (based on base diameter) and a Mach number of 0.25. Results show typical surface flow separation patterns, the magnitude of surface flow angles, and the extent of laminar and turbulent flow for symmetric, asymmetric, and wakelike flow regimes.

Keener, E. R.↗
NASA NTRS1975

Measurement of post-separated flow fields on airfoils

Detailed experimental measurements have been made of separated flow fields on a two-dimensional airfoil at low speeds. A rather small pitch yaw pressure probe was chosen. This probe has the capability of remote traversing in the vertical axis and remote yawing of plus or minus 180 deg. The calibration of the probe indicates a useful pitch angle range of about plus or minus 45 deg. The probe and its calibrations provide static and total pressure information as well as three components of velocity. Description and calibration of the probe and typical velocity and pressure plots of the separated flow fields are included.

Seetharam, H. C.↗
NASA NTRS2004

Parametric Studies of Flow Separation using Air Injection

Boundary Layer separation causes the airfoil to stall and therefore imposes dramatic performance degradation on the airfoil. In recent years, flow separation control has been one of the active research areas in the field of aerodynamics due to its promising performance improvements on the lifting device. These active flow separation control techniques include steady and unsteady air injection as well as suction on the airfoil surface etc. This paper will be focusing on the steady and unsteady air injection on the airfoil. Although wind tunnel experiments revealed that the performance improvements on the airfoil using injection techniques, the details of how the key variables such as air injection slot geometry and air injection angle etc impact the effectiveness of flow separation control via air injection has not been studied. A parametric study of both steady and unsteady air injection active flow control will be the main objective for this summer. For steady injection, the key variables include the slot geometry, orientation, spacing, air injection velocity as well as the injection angle. For unsteady injection, the injection frequency will also be investigated. Key metrics such as lift coefficient, drag coefficient, total pressure loss and total injection mass will be used to measure the effectiveness of the control technique. A design of experiments using the Box-Behnken Design is set up in order to determine how each of the variables affects each of the key metrics. Design of experiment is used so that the number of experimental runs will be at minimum and still be able to predict which variables are the key contributors to the responses. The experiments will then be conducted in the 1ft by 1ft wind tunnel according to the design of experiment settings. The data obtained from the experiments will be imported into JMP, statistical software, to generate sets of response surface equations which represent the statistical empirical model for each of the metrics as a function of the key variables. Next, the variables such as the slot geometry can be optimized using the build-in optimizer within JMP. Finally, a wind tunnel testing will be conducted using the optimized slot geometry and other key variables to verify the empirical statistical model. The long term goal for this effort is to assess the impacts of active flow control using air injection at system level as one of the task plan included in the NASAs URETI program with Georgia Institute of Technology.

Zhang, Wei↗
NASA NTRS1990

Jet vortex generators for turbulent flow separation control

A parametric study was performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low speed turbulent flow over a two dimensional rearward-facing ramp. Results indicate that flow separation control can be accomplished with the level of control achieved being a function of jet speed, jet orientation (with respect to the free stream direction), and orifice pattern (double row of jets vs. single row). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed).

Selby, Gregory↗
NASA NTRS1975

Separated flow over a body of revolution

A method is developed to determine the flowfield of a body of revolution in separated flow. The technique employed is the use of the computer to integrate various solutions and solution properties of the sub-flowfields which make up the entire flowfield without resorting to a finite difference solution to the complete Navier-Stokes equations. The technique entails the use of the unsteady cross flow analogy and a new solution to the required two-dimensional unsteady separated flow problem based upon an unsteady discrete-vorticity wake. Data for the forces and moments on bodies of revolution at high angle of attack (outside the range of linear inviscid theories) such that the flow is substantially separated are produced which compare well with experimental data at low speeds. In addition, three-dimensional steady separation regions and wake vortex patterns are determined.

Marshall, F. J.↗
NASA NTRS1989

Method and apparatus for detecting laminar flow separation and reattachment

The invention is a method and apparatus for detecting laminar flow separation and flow reattachment of a fluid stream by simultaneously sensing and comparing a plurality of output signals, each representing the dynamic shear stress at one of an equal number of sensors spaced along a straight line on the surface of an airfoil or the like that extends parallel to the fluid stream. The output signals are concurrently compared to detect the sensors across which a reversal in phase of said output signal occurs, said detected sensors being in the region of laminar separation or reattachment. The novelty in this invention is the discovery and use of the phase reversal phenomena to detect laminar separation and attachment of a fluid stream from any surface such as an airfoil supported therein.

Stack, John P.↗
NASA NTRS1990

Jet vortex generators for turbulent flow separation control

A parametric study was performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low-speed turbulent flow over a two-dimensional rearward-facing ramp. Results indicate that flow separation control can be accomplished with the level of control achieved being a function of jet speed, jet orientation (with respect to the free-stream direction), and orifice pattern (double row of jets vs. single row). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed).

Selby, G.↗
NASA NTRS2015

Flow Separation Control on A Full-Scale Vertical Tail Model Using Sweeping Jet Actuators

This paper describes test results of a joint NASA/Boeing research effort to advance Active Flow Control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jets AFC was tested at the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The flow separation control optimization was performed at 100 knots, a maximum rudder deflection of 30deg, and sideslip angles of 0deg and -7.5deg. Greater than 20% increments in side force were achieved at the two sideslip angles with a 31-actuator AFC configuration. Flow physics and flow separation control associated with the AFC are presented in detail. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The momentum coefficient (C sub mu) is shown to be a useful parameter to use for scaling-up sweeping jet AFC from sub-scale tests to full-scale applications. Reducing the number of actuators at a constant total C(sub mu) of approximately 0.5% and tripling the actuator spacing did not significantly affect the flow separation control effectiveness.

Andino, Marlyn Y.↗
NASA NTRS1981

Crossflow effects on steady and fluctuating pressures on an ogive-cylinder cone-frustum model in supersonic separated flow

Wind-tunnel tests were conducted on an ogive-cylinder model with two axisymmetric protuberances having cone frustum angles of cone = 23 deg and 45 deg that were used to generate detached shock waves and the resulting separated flow areas downstream of the shock. The tests were conducted in a 9 by 7 foot supersonic wind tunnel at a free-stream Mach number of 2.0 and at Reynolds numbers of 1.5 x 1 million and 3.9 x 1 million, based on body diameter. The model had an afterbody fineness ratio of 8.3, and the ogive nose had a fineness ratio of 3.0. Two characteristics of the fluctuating pressures in surface vortex flows that result from the crossflow component, (velocity along the tunnel longitudinal axis free stream angle of attack), in combination with changes in the longitudinal pressure gradient were measured: (1) the broadband, rms-pressure coefficients and (2) the power spectral densities. Measurements are presented for various flow regions on the model such as the attached turbulent boundary layer, the detached frustum shock wave, and separated flow areas. The results indicate that the pressure fluctuations around or in the neighborhood of the foci of the vortex flows had broadband intensities and power spectral densities nearly identical to the levels previously measured in separated-flow regions at angles of attack of 0 deg.

Dods, J. B., Jr.↗