SEARCH · Search NASA
Results for “Silicon Solar Cells”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Shunt mitigation toward efficient large-area perovskite-silicon tandem solar cells
Not provided.
Efficient and stable perovskite solar cells based on blade-coated CH 3 NH 3 PbI 3 thin films fabricated using “green” solvents under ambient conditions
Metal halide perovskites are considered the most promising candidates for solar cells of the decade due to their exceptional optical and electronic properties. The power conversion efficiency of metal halide perovskites, when incorporated as the active layer of solar cells, has become comparable to that observed for conventional silicon solar cells. However, the stability, scaleup, green solvent usage, and fabrication in ambient conditions of metal halide perovskites need to be solved for commercial applications. Here, in this work, we report the fabrication of blade-coated methylammonium lead iodide (MAPbI 3 ) perovskite thin films using methylamine and acetonitrile as “green” solvents under ambient conditions. Our perovskite films are initially prepared from low purity PbI2 (99%) and are blade-coated in dry air at relative humidity (RH) levels above 30%. A significant advantage of fabricating our perovskite thin films via blade-coating protocols is that there is a minimal amount of precursors (5 μL) used compared to spin-coating methods (50μL–60μL) for a 4 cm 2 substrate. With the addition of a small amount of an organic halide salt, namely, phenethylammonium chloride, the film crystallinity is improved and non-radiative recombination is suppressed, resulting in power conversion efficiencies over 20%. In addition, the device maintains more than 95% of its initial efficiency after 500 h under continuous light illumination of 1-sun at open circuit conditions, 50 °C and 60% RH. The above method leads a path towards the commercial fabrication of perovskite solar cells.
Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts
In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.
Machine-Learning-Assisted Enhancement of Perovskite Stability and Photovoltaic Performance
Lab scale perovskite solar cells (PSCs) have reached power conversion efficiencies on par with silicon solar cells. Their potential for low-cost manufacturing combined with high performance make them attractive for commercialization. The major challenge impeding widespread development of PSCs is their stability. Halide perovskites are vulnerable to decomposition in the presence of moisture, oxygen, light, and heat. Furthermore, the chemical differences between halide perovskites and conventional semiconductors used in photovoltaics (e.g., silicon, chalcogenides, and III-V compounds) may render established accelerated lifetime testing protocols inaccurate.
Mitigation of shunt in poly -Si/SiO$_{x}$ passivated interdigitated back contact monocrystalline Si solar cells by self-aligned etching between doped fingers
Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts can be used for ultra-high-efficiency interdigitated back contact (IBC) monocrystalline silicon solar cells. We evaluate the use of intrinsic poly-Si for the region that isolates the p- and n-type fingers at the back side of IBC devices. To mitigate shunt across the isolation region between the doped p- and n-type fingers, we demonstrate self-aligned subtractive processing by etching the poly-Si in the isolation region using SF6 plasma followed by etching in a tetramethylammonium hydroxide (TMAH) solution. After removal of the poly-Si, the isolation region was passivated with SiN x and Al 2 O 3 , which resulted in an 11.7% increase in the fill factor in a 19.8% efficient device. Furthermore, we evaluate the limitations of this device through Suns-V oc analysis and simulations using SunSolve and Quokka3 solar cell simulation software. Through Quokka3, we show that the most significant efficiency losses come from junction recombination current (J 02 ) in the isolation region between doped fingers. We predict that the cell efficiency can be most improved with reduced J 02 through better isolation of heavily doped fingers by etching the isolation region deeper into the bulk or through enhanced surface chemical passivation in this region.
Sputtered indium tin oxide as a recombination layer formed on the tunnel oxide/poly-Si passivating contact enabling the potential of efficient monolithic perovskite/Si tandem solar cells
We focus on utilizing sputtered indium tin oxide (ITO) as a recombination layer, having low junction damage to an n-type silicon solar cell with a front-side tunnel oxide passivating electron contact, thereby enabling the development of a high efficiency monolithic perovskite/Si tandem device. High transparency and low resistivity ITO films are deposited via low power DC magnetron sputtering at room temperature onto a front-side thin SiO x /n + poly-Si contact in a complete Cz n-Si cell with a back-side Al 2 O 3 /SiN x passivating boron-diffused p + -emitter on a random pyramid textured surface. We report the cell characteristics before and after ITO sputtering, and we find a cure at 250 °C in air is highly effective at mitigating any sputtering induced damage. Our ITO coated sample resulted in an implied open-circuit voltage (iV oc ) of 684.7 ± 11.3 mV with the total saturation current density of 49.2 ± 14.8 fA/cm 2 , an implied fill factor (iFF) of 81.9 ± 0.8%, and a contact resistivity in the range of 60 mΩ-cm 2 to 90 mΩ-cm 2 . After formation of a local Ag contact to the rear emitter and sputtered ITO film as the front-side contact without grid fingers, the pseudo-efficiency of 20.2 ± 0.5% was obtained with the V oc of 670.4 ± 7 mV and pseudo FF of 77.3 ± 1.3% under simulated one sun with the calculated short-circuit current density of 30.9 mA/cm 2 from the measured external quantum efficiency. Furthermore, our modelling result shows that efficiency exceeding 25% under one sun is practically achievable in perovskite/Si tandem configuration using the ITO recombination layer connecting a perovskite top cell and a poly-Si bottom cell.
Optimization of four terminal rear heterojunction GaAs on Si interdigitated back contact tandem solar cells
High-efficiency, four-terminal tandem solar cells composed of thin GaAs films mechanically stacked onto interdigitated back contact silicon solar cells with a glass interlayer are demonstrated. The optimal thickness of the absorber layer of a rear heterojunction GaAs subcell for use in four terminal tandem solar cells was studied. GaAs top cells with absorber layer thicknesses of 1.5, 1.9, 2.3, 2.8, and 3.5 µm were fabricated on glass and mechanically stacked onto interdigitated back-contact Si bottom cells. All tandem cells were found to have efficiencies above 30% under the AM1.5 G spectrum demonstrating a relatively weak sensitivity to thickness in the four-terminal configuration. We found the 2.8 µm absorber layer cell to have the highest top cell and tandem cell efficiency at 26.38% and 32.57%, respectively. Optical modeling with transfer matrix method for the planar top cell and Lambertian light trapping in the textured Si subcell, along with drift-diffusion Hovel equations, were used to show photon recycling enhancement to the effective diffusion length and VOC of the top cell as a result of the low-index glass interlayer.
Self‐Assembled Monolayer Templating for Engineered Nanopinholes in Passivated Contact Solar Cells
We present a novel self-assembled monolayer (SAM)-based technique to make nanopinhole-enabled passivated contacts on silicon solar cells by tuning the SAM coverage area and etch selectivity. We deposit trimethyl-silyl Si(CH 3 ) 3 groups using hexamethyldisilazane (HMDS) as the precursor over passivating dielectric layers and their stacks (SiO 2 , SiN x , SiO 2 /SiN x ) and interrupt the HMDS attachment chemistry shortly before a full monolayer is formed on its surface. Subsequent etching in dilute HF produces pinholes through the dielectric layers due to the higher etch resistance of the SAM to HF etching. The pinhole areal density (10 4 –10 8 /cm 2 ) and size (10–1000 nm) can be tuned both by duration of HMDS attachment and HF etch time. Pinholes were characterized by atomic force microscopy, tetramethylammonium hydroxide (TMAH) selective etch, and Ag decoration by electroless plating. Polysilicon (poly-Si) passivated contacts enabled by pinholes were formed by subsequent deposition of doped amorphous silicon (a-Si:H) followed by thermal crystallization and dopant drive-in. At optimal areal pinhole density ≈10 7 /cm 2 , contacts exhibit both passivation and carrier transport via pinholes as evidenced by electron beam induced current, transmission line measurements, and carrier lifetime measurements. Solar cells based with these pinhole contacts show V oc = 723 mV and FF = 80.3%. The remaining SAM layer does not affect device performance.
Extended Accelerated Stress Testing of Lamination-Free Edge-Sealed Photovoltaic Minimodules
Lamination-free minimodules are constructed with silicon solar cells between glass sheets and an edge seal of polyisobutylene and silicone. These samples are stressed using a repeated sequential testing sequence including ultraviolet-containing simulated solar spectrum light exposure at elevated temperature, damp heat, humidity freeze, and thermal cycling adapted from the International Electrotechnical Commission (IEC) TS 63209-2:2022. The minimodule performance throughout the stressing is characterized by flash testing and electroluminescence imaging. Results are compared to conventional laminated minimodules using the same type of solar cells. The lamination-free minimodules experience up to 8% power loss compared to roughly 3% for the laminated versions. However, those losses, dominated by current and fill factor, are caused by glass soiling and busbar ribbon separation on the cells. When glass is replaced and the stressed cells are contacted with probes bypassing the delaminated ribbons, the initial performance is recovered, and overall losses of the lamination-free samples become negligible.
Accelerated reliability tests of n + and p + poly-Si passivated contacts
We report on the stability of encapsulated, low-pressure chemical vapor-deposited phosphorus (n + poly-Si) doped and boron (p + poly-Si) doped poly-Si/SiO x passivated contacts by exposing the samples to three different accelerated tests: damp heat test, thermal cycling and ultraviolet exposure, adhering closely to the IEC 61215 standard. Outdoor testing was also performed by exposing the samples in the outdoor testing field at the National Renewable Energy Laboratory, and preliminary data accumulated for 1000 h from February to April of 2021 is reported. We studied non-metallized, thermally-metallized, and screen-printed n + and p + poly-Si by monitoring the effective minority carrier lifetime at the implied maximum power point using a Sinton lifetime tester, and recorded photoluminescence images before and after the exposure. Furthermore, the samples were found to be stable under all test conditions, which is encouraging for incorporation of these contacts in next-generation industrial silicon solar cells.
Luminescent Solar Concentrator Tandem-on-Silicon with above 700mV Passivated Contact Silicon Bottom Cell
Luminescent solar concentrator (LSC) tandem-on-silicon (Si) provides a route towards achieving higher than 30% overall efficiency which can overcome the theoretical efficiency limit of a single junction Si cell. Here, we present optical coupling and performance of high Voc passivated contact Si bottom cell for LSC tandem-on-Si where the top module consists of highly efficient luminophores and an array of micro InGaP cells embedded in a poly (lauryl methacrylate) waveguide. In this device configuration, InGaP cell area coverage is only ~0.5% of the total LSC area which significantly reduces the high cost III-V material usage. The performance of Si sub-cell is investigated under LSC spectrum and is compared against the measurement done under 1 um thick InGaP filter which mimics the spectrum seen by Si bottom cell in a conventional III-V/Si tandem. V oc of greater than 700 mV has been observed for the passivated contact Si bottom cell in these tandem applications.
Design, Optimization, and In-Depth Understanding of Front and Rear Junction Screen-Printed Double-Side Passivated Contacts Solar Cells
Investigate the efficiency potential of n-type screen-printed poly-Si based double-side tunnel oxide passivated contacts (DS-TOPCon) silicon solar cells Establish key material/device parameters and technologies to attain practically achievable DS-TOPCon cell efficiency by Quokka 2D Develop fundamental understanding of underlying mechanisms governing cell operation in front junction (FJ) and rear junction (RJ) cell designs to explain why RJ is a better choice for DS-TOPCon structure
Scalable Two–Step Production of High–Efficiency Perovskite Solar Cells and Modules
Perovskite solar cells (PSCs) fabricated in laboratories have already achieved power conversion efficiency (PCE) comparable to market-dominant crystalline silicon solar cells. However, this promising photovoltaic technology suffers from severe loss of PCE during scaling up, limiting its progress toward commercialization. One critical question is to develop scalable, low-cost, high throughput, and well-controlled production methods to deposit high-quality perovskite films. Among various approaches, two-step sequential deposition methods have their unique advantages but have been long overlooked. This review provides an overview of two-step methods for fabricating efficient and stable perovskite solar modules (PSMs). We first discuss the mechanisms of two-step perovskite conversion and advanced engineering approaches to modulate the perovskite formation process. We survey the progress of efficient PSCs prepared by different two-step methods and compare the advantages and disadvantages of each method for scalable production of PSMs. Particularly, we highlight that the vapor-based two-step methods are promising for high-throughput in-line production of PSMs. Finally, we provide insights into the challenges and outlook of the industrialization of two-step processes for producing PSMs.
Additive‐Free Oxidized Spiro‐MeOTAD Hole Transport Layer Significantly Improves Thermal Solar Cell Stability
Perovskite solar cells are among the most promising new solar technologies, already surpassing polycrystalline silicon solar cell efficiencies. The stability of the highest efficiency devices at elevated temperature is, however, poor. These cells typically use Spiro-MeOTAD as the hole transporting layer. It is generally believed that additives, required for enhancing electrical conductivity and optimizing energy level alignment, are responsible for the reduced stability—inferring that Spiro-MeOTAD based hole transporting layers are intrinsically unstable. Here, a reliable noble metal free synthesis of Spiro-MeOTAD (bis(trifluoromethane)sulfonimide) 4 is presented which is used as the oxidizing agent. No additives are added to the partially oxidized Spiro-MeOTAD hole-transporting layer. Device efficiencies up to 24.2% are achieved. Electrical conductivity is largely developed by the first 1% oxidation. Further oxidation shifts the energy levels away from the vacuum level, which allows tuning of the energy level alignment without the use of additives—contradicting the current understanding of this system. Without additives, devices demonstrate significant improvement in stability at elevated temperatures up to 85 °C under one sun over 1400 h continuous illumination. The remaining degradation is pinpointed to ion migration and reactions in the perovskite layer which may be further suppressed with compositional engineering and adequate ion barrier layers.
Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells
This paper explores the potential of the negatively charged SiN x using plasma charge injection technology to passivate the front textured boron-diffused emitter of n-type Si solar cells. The high-x value single SiN x layer with x ≥ 1.30 (x = N/Si) previously developed for the planarized rear-side passivation of p-type silicon solar cells, with an excellent passivation and charge stability, was found to be unacceptable for the passivation on the front textured boron emitter of n-type cells due to a severe bulk lifetime degradation issue. Therefore, in this study, we investigated a new concept of depositing a dual-x SiN x with a low-x SiN x layer (x~1.01) on top of a high-x SiN x layer (x~1.30) for passivation of the front textured rough surface of boron diffused emitter in n-type cells. Here, the optimized dual-x SiN x stack reveals the promise of charge retention for more than 25 years in field operation as well as excellent passivation of boron-doped emitter without bulk lifetime degradation. N-type cells with the optimized dual-x SiN x after charge injection show comparable cell performance to Al 2 O 3 passivated reference cells. The results of cell-level light stability tests using one-cell minimodules exhibit cell performance decay characteristics similar to the traditional Al 2 O 3 /SiN x passivated reference module.
Solar cell contacts: quantifying the impact of interfacial layers on selectivity, recombination, charge transfer, and V oc
Interfacial layers (IFLs) are ubiquitous in solar cells, but their precise impact on carrier transfer rates and the relation of these rates to performance metrics and the concepts of selectivity and recombination is lacking. We report the use of a well-defined interdigitated back-contact (IBC) silicon solar cell to determine the precise role of such IFLs. We characterize the action of the common IFL spiro-OMeTAD by making it a third contact to the IBC cell. This architecture creates three solar cells within a single structure that, with numerical simulation, provide the exchange current densities (i.e., charge transfer rates) for electrons ( J 0n ) and holes ( J 0p ) and the quasi Fermi-level splitting in the absorber, which measures the balance of generation and recombination. Further, we describe the relation of V oc to contact recombination, the asymmetry in electron/hole collection rates at a single contact (contact selectivity), and the asymmetry in collection rates of the same carrier at separate contacts (carrier selectivity). Relative to bare gold, neat spiro-OMeTAD reduces J 0n and J 0p (their geometric mean ( J 0n J 0p ) 0.5 decreases by 10 4 ), decreasing contact recombination. Addition of the common dopant Li-TFSI and air increase J 0p / J 0n by 10 6 with little effect on ( J 0n J 0p ) 0.5 , increasing contact hole selectivity. The significant increase in V oc observed by introducing spiro-OMeTAD/Li-TFSI IFLs into the cells studied, however, is due to an increase in the carrier selectivity rather than the contact selectivity or recombination of the spiro-OMeTAD-modified contact. Operando measurements further show voltage-dependent changes in the J 0 s, demonstrating that spiro-OMeTAD contributes to hysteresis. Broader context : Solar cells operate by photogenerating excess charge carriers in an absorber material and, in competition with recombination, asymmetrically extracting them at so-called carrier-selective contacts, one that ideally collects only electrons and the other, only holes. Particularly in emerging photovoltaics such as perovskites, thin layers of organic semiconductors or related materials are introduced between the absorber and contact to improve power conversion efficiency. In terms of interfacial charge transfer, a prevailing view is that such interfacial layers improve performance by helping block the collection of the undesired carrier, considered a form of recombination. We use a novel platform to study the simultaneous impact of spiro-OMeTAD, a common interfacial layer, on the collection of electrons, the collection of holes, and on the recombination of electrons and holes. We quantitatively demonstrate that spiro-OMeTAD layers indeed passivate the contact toward recombination, but that larger improvements in the open-circuit voltage, a key cell metric, can come not only from this but also from increasing the asymmetry of the collection of electrons in the system. Further, operando measurements show transient changes in the properties of spiro-OMeTAD which suggest that it contributes to hysteresis phenomena commonly observed in perovskite and other solar cells.