Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar diffuser”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Impact of Water Ingress on Molybdenum Thin Films and Its Effect on Cu(In,Ga)Se 2 Solar Cells

Solar cell degradation can occur through many pathways and at the different stages of the fabrication process, notably because of the water condensation. In the case of Cu(In,Ga)Se 2 (CIGS) solar cells, the impact of water ingress on Mo back contact can be substantial for not only the film itself but also the device performance and reliability. Microstructural modification, change in film morphology, loss in reflectance, and increased resistivity because of the moisture ingress were observed via X-ray diffraction, transmission electron microscopy, spectroscopic ellipsometry, and four-point probe measurements, respectively. Secondary ion mass spectrometry measurements revealed drastic changes in the alkali (Na, K) profiles in both the CIGS and Mo layers, likely because of the modification of their diffusion coefficient through Mo. This, in turn, negatively impacts the solar cell efficiency by decreasing both fill factor and open-circuit voltage. Additional experiments, modifying the substrate and utilizing a NaF postdeposition treatment, highlight the mechanisms of degradation as being due to both a modification of the Mo/CIGS interface and the lack of alkali diffusion after water ingress.

14 SOLAR ENERGY↗
DOE OSTI2021

Improvement of Front-Junction GaInP by Point-Defect Injection and Annealing

Traditional front junction GaInP solar cells are radiation tolerant and can have good diffusion length, but have limited voltage and thus efficiency. Here, we investigate the impact of annealing on GaInP device performance. First, Zn-doped GaInP/AlGaInP double heterojunction structures are studied in order to investigate the impact of annealing in a simple structure. While standard anneals lower diffusion length and lifetime, annealing after injecting point-defects improves material quality, presumably by eliminating sources of non-radiative recombination. Atomic ordering is reduced by the anneal, which raises the device bandgap and requires consideration. These results can be used to improve front junction device performance while controlling the bandgap. Then, GaInP front-junction devices are created using anneals with and without point-defect injection. Voc and EQE trends follow the diffusion length and lifetime trends from the DH structures. Baseline devices have Woc of 0.484 V, raising to 0.504 V after a high temperature anneal. However, injecting point defects prior to the anneal results in a front junction device with Woc of 0.405 V and a diffusion length greater than 8 micrometers. Optimized front-junction GaInP devices with an ARC have ~20% efficiency without a rear reflector.

anneal↗
DOE OSTI2021

Improvement of Front-Junction GaInP by Point-Defect Injection and Annealing: Preprint

Traditional front junction GaInP solar cells are radiation tolerant and can have good diffusion length, but have limited voltage and thus efficiency. Here, we investigate the impact of annealing on GaInP device performance. First, Zn-doped GaInP/AlGaInP double heterojunction structures are studied in order to investigate the impact of annealing in a simple structure. While standard anneals lower diffusion length and lifetime, annealing after injecting point-defects improves material quality, presumably by eliminating sources of non-radiative recombination. Atomic ordering is reduced by the anneal, which raises the device bandgap and requires consideration. These results can be used to improve front junction device performance while controlling the bandgap. Then, GaInP front-junction devices are created using anneals with and without point-defect injection. Voc and EQE trends follow the diffusion length and lifetime trends from the DH structures. Baseline devices have Woc of 0.484 V, raising to 0.504 V after a high temperature anneal. However, injecting point defects prior to the anneal results in a front junction device with Woc of 0.405 V and a diffusion length greater than 8 micrometers. Optimized front-junction GaInP devices with an ARC have ~20% efficiency without a rear reflector.

anneal↗
DOE OSTI2026

Solar Resource Measurements in Eugene, OR: Cooperative Research and Development Final Report, CRADA Number CRD-07-00252

Site-specific, long-term, continuous, and high-resolution measurements of solar irradiance are important for developing renewable resource data. These data are used for several research and development activities consistent with the NLR mission: establish a national 3-year climatological database of measured solar irradiances; provide high quality ground-truth data for satellite remote sensing validation; support development of radiative transfer models for estimating solar irradiance from available meteorological observations; provide solar resource information needed for technology deployment and operations. Data acquired under this agreement will be available to the public through NLR's Measurement & Instrumentation Data Center – MIDC (http://www.nlr.gov/midc) Or the Renewable Resource Data Center - RReDC (http://rredc.nlr.gov). The MIDC offers a variety of standard data display, access, and analysis tools designed to address the needs of a wide user audience (e.g., industry, academia, and government interests).

14 SOLAR ENERGY↗
DOE OSTI2026

Impact of the Annealing Temperature on the Local Se Distribution and Optical Properties in CdSexTe1-x Solar Cells by Multimodal X-ray Microscopy

The introduction of Se in CdTe solar-cell absorbers has led to multiple beneficial effects in the devices, including an increased short-circuit current and an extended charge-carrier lifetime. A critical manufacturing step of CdSexTe1-x solar cells is CdCl2 annealing at high temperatures, during which Se diffuses through the absorber layer. Understanding the local Se distribution in the absorber and its impact on optical properties of the material is key for the further development of this thin-film solar cell technology. In a multimodal x-ray scanning microscopy approach, we investigated the impact of the annealing temperature of CdSexTe1-x solar cells on the Se distribution and on optical characteristics of the material. For this purpose, we exploited an upgraded x-ray excited optical luminescence (XEOL) detection unit that enables simultaneous spectrally and temporally resolved XEOL mapping at synchrotron facilities that are ideal for studying thin-film solar-cell materials with hard x-rays featuring high penetration depth and lateral resolution.

14 SOLAR ENERGY↗
DOE OSTI2020

Long-range exciton diffusion in molecular non-fullerene acceptors

Abstract The short exciton diffusion length associated with most classical organic semiconductors used in organic photovoltaics (5-20 nm) imposes severe limits on the maximum size of the donor and acceptor domains within the photoactive layer of the cell. Identifying materials that are able to transport excitons over longer distances can help advancing our understanding and lead to solar cells with higher efficiency. Here, we measure the exciton diffusion length in a wide range of nonfullerene acceptor molecules using two different experimental techniques based on photocurrent and ultrafast spectroscopy measurements. The acceptors exhibit balanced ambipolar charge transport and surprisingly long exciton diffusion lengths in the range of 20 to 47 nm. With the aid of quantum-chemical calculations, we are able to rationalize the exciton dynamics and draw basic chemical design rules, particularly on the importance of the end-group substituent on the crystal packing of nonfullerene acceptors.

14 SOLAR ENERGY↗
DOE OSTI2024

National Climate Database (NCDB)

The National Climate Database (NCDB) is a high resolution, bias-corrected climate dataset consisting of the three most widely used variables of solar radiation- global horizontal (GHI), direct normal (DNI), and diffuse horizontal irradiance (DHI)- as well as other meteorological data. The goal of the NCDB is to provide unbiased high temporal and spatial resolution climate data needed for renewable energy modeling. The NCDB is modeled using a statistical downscaling approach with Regional Climate Model (RCM)-based climate projections obtained from the North American Coordinated Regional Climate Downscaling Experiment (NA-CORDEX; linked below). Daily climate projections simulated by the Canadian Regional Climate Model 4 (CanRCM4) forced by the second-generation Canadian Earth System Model (CanESM2) for two Representative Concentration Pathways (RCP4.5 or moderate emissions scenario and RCP8.5 or highest baseline emission scenario) are selected as inputs to the statistical downscaling models. The National Solar Radiation Database (NSRDB) is used to build and calibrate statistical models.

Array↗
DOE OSTI2023

A Data-driven, Physics-based Transport Model of Solar Energetic Particles Accelerated by Coronal Mass Ejection Shocks Propagating through the Solar Coronal and Heliospheric Magnetic Fields

Abstract In an effort to develop computational tools for predicting radiation hazards from solar energetic particles (SEPs), we have created a data-driven physics-based particle transport model to calculate the injection, acceleration, and propagation of SEPs from coronal mass ejection (CME) shocks traversing through the solar corona and interplanetary magnetic fields. The model runs on an input of corona and heliospheric plasma and magnetic field configuration from a magnetohydrodynamic model driven by solar photospheric magnetic field measurements superposed with observed CME shocks determined from coronagraph images. SEP source particles are injected at the shock using the result of diffusive shock acceleration formulation from a characteristic obliquity-dependent injection from a heated solar wind thermal tail population. With several advanced computation techniques involving stochastic simulation and integration, the model obtains the particle intensity at any location in interplanetary space through the rigorous solution to the time-dependent 5D focus transport equation in the phase space that includes perpendicular diffusion. We apply the model to the 2011 November 3 CME event. The calculation results reproduce multispacecraft SEP observations at Earth and STEREO-B reasonably well without normalization of particle flux. The observations at STEREO-A can be reproduced by rescaling particle energy or modified energy dependence of particle diffusion coefficients. This circumsolar SEP event seen by spacecraft at Earth, STEREO-A, and STEREO-B at widely separated longitudes can be explained by diffusive shock acceleration by a single CME shock with a moderate speed.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Optimizing the Orientation of Solar Photovoltaic Systems Considering the Effects of Irradiation and Cell Temperature Models with Dust Accumulation

To cope with the growing installation capacities of solar photovoltaic (PV) systems in desert areas, it is necessary to revisit the energy production models and the optimal angles of PV panels given the significant impacts of ambient temperature, wind speed, dust accumulation, and cleaning frequency. In this study, these four factors are examined for four PV technologies (polycrystalline, microcrystalline, monocrystalline, and thin-film) at three cities in Jordan, Egypt, and Tunisia using precise ground-level meteo-solar measurements. Different models are compared to estimate the diffuse irradiance, as well as account for the effects of operating temperature, wind speed, and dust accumulation on energy production and optimal tilt and azimuth angles of the panels. The results reveal 1.5 % higher energy production estimates using the isotropic model, compared to the anisotropic model in the summer months. Considering the cooling effect of wind speed decreases the operating cell temperature drops by up to 7.05 % for thin film panels. The annually produced energy decreases by 24 % when the panels are cleaned bi-monthly. When the dust accumulation rate doubles, the energy production decreases by ~10 % for all studied cases. Also, the variations in optimal tilt and azimuth angles with dust accumulation rate are within ~3.0 degrees .

14 SOLAR ENERGY↗
DOE OSTI2025

Defect Diffusion Graph Neural Networks for Materials Discovery in High-Temperature Energy Applications

Here, the migration of crystallographic defects dictates material properties and performance for a plethora of technological applications. Density functional theory (DFT)-based nudged elastic band (NEB) calculations are a powerful computational technique for predicting defect migration activation energy barriers, yet they become prohibitively expensive for high-throughput screening of defect diffusivities. Without introducing hand-crafted (i.e., chemistry- or structure-specific) descriptors, we propose a generalized deep learning approach to train surrogate models for NEB energies of vacancy migration by hybridizing graph neural networks with transformer encoders and simply using pristine host structures as input. With sufficient training data, computationally efficient and simultaneous inference of vacancy defect thermodynamics and migration activation energies can be obtained to compute temperature-dependent vacancy diffusivities and to down-select candidates for more thorough DFT analysis or experiments. Thus, as we specifically demonstrate for potential water-splitting materials, candidates with desired defect thermodynamics, kinetics, and host stability properties can be more rapidly targeted from open-source databases of experimentally validated or hypothetical materials.

14 SOLAR ENERGY↗
DOE OSTI2024

Moving beyond the Aerosol Climatology of WRF-Solar: A Case Study over the North China Plain

Numerical weather prediction (NWP), when accessible, is a crucial input to short-term solar power forecasting. WRF-Solar, the first NWP model specifically designed for solar energy applications, has shown promising predictive capability. Nevertheless, few attempts have been made to investigate its performance under high aerosol loading, which attenuates incoming radiation significantly. The North China Plain is a polluted region due to industrialization, which constitutes a proper testbed for such investigation. Here, in this paper, aerosol direct radiative effect (DRE) on three surface shortwave radiation components (i.e., global, beam, and diffuse) during five heavy pollution episodes is studied within the WRF-Solar framework. Results show that WRF-Solar overestimates instantaneous beam radiation up to 795.3 W m -2 when the aerosol DRE is not considered. Although such overestimation can be partially offset by an underestimation of the diffuse radiation of about 194.5 W m -2 , the overestimation of the global radiation still reaches 160.2 W m -2 . This undesirable bias can be reduced when WRF-Solar is powered by Copernicus Atmosphere Monitoring Service (CAMS) aerosol forecasts, which then translates to accuracy improvements in photovoltaic (PV) power forecasts. This work also compares the forecast performance of the CAMS-powered WRF-Solar with that of the European Centre for Medium-Range Weather Forecasts model. Under high aerosol loading conditions, the irradiance forecast accuracy generated by WRF-Solar increased by 53.2% and the PV power forecast accuracy increased by 6.8%.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Direct Measurement of Diffusion Coefficients: Evidence for Diffusive Stochastic Heating in Collisionless Plasmas

Open questions in collisionless plasma dissipation can be addressed using space-based observations in different astrophysical environments, with implications for both astrophysical and laboratory plasma systems. We study a low-𝛽, highly imbalanced, sub-Alfvénic stream observed by Parker Solar Probe (PSP) to identify and distinguish between signatures of stochastic heating (SH) and resonant heating (RH) by parallel ion cyclotron waves (∥-ICWs). Prior work studying this stream [Trevor A. Bowen et al., Stochastic heating in the sub-Alfvénic solar wind, Phys. Rev. Lett. 135, 255201 (2025)] showed that the SH rate, accounting for intermittency, matched the amplitude of the local energy transfer (LET) rate, while the RH rate did not. This comparison relied on a number of assumptions regarding the nature of the diffusive process and the calculation of the LET rate. We introduce a novel technique of inverting the proton guiding center equation to empirically measure velocity-space diffusion coefficients using three-dimensional proton velocity distribution functions, from the ion electrostatic analyzer (the Solar Probe Analyzer for Ions) on PSP. Measured diffusion coefficients are used to determine phase-space heating rates, leading to a calculation of a fully kinetic heating rate independent of assumptions made in prior work. We show that scale-dependent analytic expressions for SH via noncoherent fluctuations match the empirical measurements from PSP data, provided that we account for intermittency in the heating calculation. In contrast, the derived heating rates for SH that accounts for the effects of the helicity barrier and heating rates for RH via ∥-ICWs do not peak in the same region of velocity space as the empirical measurements, nor do they reach the required magnitude. Our approach provides novel methodology to uniquely identify and constrain heating processes in collisionless plasmas and shows evidence of a Fokker-Planck-like diffusive process in the near-Sun solar wind.

Plasma kinetic theory↗
DOE OSTI2022

Elucidating Diiodomethane-Induced Improvement in Photonically Cured MAPbI 3 Solar Cells

Diiodomethane (CH 2 I 2 ) has been reported to improve the photonically cured perovskite solar cell (PSC) device performance by reducing pinholes. Here we show that even for pinhole-free methylammonium lead iodide (MAPbI 3 ) made by photonic curing, adding CH 2 I 2 promotes significant performance improvement. We elucidate the mechanisms behind the observed improvement. In addition to current-density versus voltage measurements, we perform a wide variety of characterization to compare the crystallinity, grain structure, optical, chemical, and electrical properties of the photonically cured samples with and without CH 2 I 2 in the MAPbI 3 layer to those of thermally annealed devices. Here, the addition of CH 2 I 2 promotes grain growth in the vertical direction, increases the I/Pb ratio in the final film, and removes the I - ionic diffusion and defect signature associated with iodine interstitials. As a result, we achieve a champion efficiency of 15.04% with MAPbI 3 conversion time of 20 ms, comparable to PSCs that have MAPbI 3 layer thermally annealed for 10 min. Understanding the mechanisms behind additive-induced improvements for non-thermal annealing processes is critical to enabling high-speed PSC manufacturing.

14 SOLAR ENERGY↗
DOE OSTI2021

Modeling the electrochemical behavior and interfacial junction profiles of bipolar membranes at solar flux relevant operating current densities

A 1-dimensional, multi-physics model that accounts for the migration and diffusion of solution species, electrostatics, and chemical reactions, in particular water dissociation (WD), at bipolar membrane (BPM) interfaces was developed to study the electrochemical behavior of bipolar membranes (BPMs) at solar flux relevant operating current densities (tens of mA cm -2 ). Significant partial current densities for WD were observed at BPM voltages much less than the equilibrium voltage, e.g., 59 mV × ΔpH from both experiments and modeling. The co-ion leakage across the BPM at pH differentials accounted for the early presence of the partial current density for WD. Two distinctive electric field dependent WD pathways, the un-catalyzed pathway and the catalyzed pathway, were quantitatively and parametrically studied to improve the turn-on potential of the BPM. The catalyzed pathway accounted for the majority of the partial current density for WD at low voltages, while the un-catalyzed pathway dominated the WD at relatively high voltages. Significant WD was observed only within the interfacial CL (<5 nm), in which a large electric field was present. To improve the electrochemical behavior and the turn-on potential of BPMs, the impacts of the pKa of the immobilized WD catalysts, the electric-field dependent rate constant, the thickness of the catalyst layer and fixed charge density in BPMs on the partial current densities for WD were studied systematically. In addition, the electrochemical behavior and concentration profiles of BPMs in a buffered electrolyte were studied and contrasted with those in an un-buffered electrolyte from both modeling and experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Doped GaInAs/GaP Quantum Well Superlattice Solar Cells With 27.5% Efficiency

Quantum wells can extend the absorption range of a solar cell and are typically placed in the intrinsic region of the device to enable efficient carrier collection via drift. Thick intrinsic regions are needed for significant absorption in the low bandgap quantum wells, resulting in a large depletion region recombination and ultimately a solar cell with a low fill factor (FF). However, in quantum well superlattice solar cells where tunneling plays a dominant role in carrier transport, collection by carrier diffusion may be possible, relieving the requirement for quantum wells to be placed in the intrinsic region. Here, we investigate doping in stress-balanced quantum well superlattice solar cells using thin 2 nm GaP barriers. Doping reduces J02 depletion region recombination and improves the solar cell FF up to 86.7%, but very high doping eventually reduces the carrier collection, leading to a tradeoff in efficiency. Finally, we show that the barrier thickness also plays an important role in carrier collection, and we demonstrate high efficiency 27.5% single-junction devices with a doped superlattice.

13 HYDRO ENERGY↗
DOE OSTI2024

Understanding Process–Structure Relationships during Lamination of Halide Perovskite Interfaces

Fabrication of halide perovskite (HP) solar cells typically involves the sequential deposition of multiple layers to create a device stack, which is limited by the thermal and chemical incompatibility of top contact layers with the underlying HP semiconductor. One emerging strategy to overcome these restrictions on material selection and processing conditions is lamination, where two half-stacks are independently processed and then diffusion bonded to complete the device. Lamination reduces the processing constraints on the top side of the solar cell to allow new device designs, expanded use of deposition methods, and self-encapsulation of devices. While laminated perovskite solar cells with high efficiencies and novel interlayer combinations have been demonstrated, there is a limited understanding of how the lamination process parameters affect the diffusion-bond quality and material properties of the resulting HP layer. In this study, we systematically vary temperature, pressure, and time during lamination and quantify the resulting impacts on bonded area, grain domain size, and photoluminescence. A design of experiments is performed, and statistical analysis of the experimental results is used to quantitatively evaluate the resulting process–structure–property relationships. The lamination temperature is found to be the key parameter controlling these properties. Furthermore, a temperature of 150 °C enables successful bonding over 95% of the substrate area and also results in increases in apparent grain domain size and photoluminescence intensity. Based on these insights, the lamination temperature of functional perovskite solar cell devices is varied, demonstrating the importance of the resulting bond quality on device performance metrics.

14 SOLAR ENERGY↗
DOE OSTI2025

Co‐Doping Approach for Enhanced Electron Extraction to TiO 2 for Stable Inorganic Perovskite Solar Cells

Inorganic perovskite CsPbI 3 solar cells hold great potential for improving the operational stability of perovskite photovoltaics. However, electron extraction is limited by the low conductivity of TiO 2 , representing a bottleneck for achieving stable performance. In this study, a co‐doping strategy for TiO 2 using Nb(V) and Sn(IV), which reduces the material's work function by 80 meV compared to Nb(V) mono‐doped TiO 2 , is introduced. To gain fundamental understanding of the processes at the interfaces between the perovskite and charge‐selective layer, transient surface photovoltage measurements are applied, revealing the beneficial effect of the energetic and structural modification on electron extraction across the CsPbI 3 /TiO 2 interface. Using 2D drift‐diffusion simulations, it is found that co‐doping reduces the interface hole recombination velocity by two orders of magnitude, increasing the concentration of extracted electrons by 20%. When integrated into n–i–p solar cells, co‐doped TiO 2 enhances the projected T S80 lifetimes under continuous AM1.5G illumination by a factor of 25 compared to mono‐doped TiO 2 . This study provides fundamental insights into interfacial charge extraction and its correlation with operational stability of perovskite solar cells, offering potential applications for other charge‐selective contacts.

14 SOLAR ENERGY↗