Search NASA⌕ Search

SEARCH · Search NASA

Results for “Static pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Modelling the development of capillary pressure in freshly 3D-printed concrete elements

3D concrete printing is a promising technology recently developed to automate construction. Since no formwork is used in this technology to support and protect fresh concrete, there are two aspects which considerably accelerate the development of capillary pressure in 3D-printed concrete in comparison to conventionally placed concrete: i) high stiffness of 3D-printed needed to provide sufficient buildability, and ii) very early and fast evaporation of pore water. Accelerated development of capillary pressure may lead to severe plastic shrinkage cracking in 3D-printed elements and, hence, need to be mitigated. This investigation aims at providing a poromechanical model for capillary pressure development in 3D-printed elements. To simulate the development of capillary pressure and plastic shrinkage, environmental factors, material properties, and element geometry need to be considered as a whole. The model inputs – coefficient of permeability, static bulk modulus, air entry pressure and chemical shrinkage rate – were determined experimentally. The model was validated for two fine-grained concretes. Both 3D-printed materials yielded faster capillary pressure increase in comparison to cast concrete, while partial substitution of cement with silica fume further accelerated the capillary pressure development. Furthermore, due to the lower permeability of the mixture containing silica fume, the gradient of capillary pressure between 3D-printed layers increased, as did the gradient of plastic shrinkage.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pressure-induced structural and dielectric changes in liquid water at room temperature

Understanding the pressure-dependent dielectric properties of water is crucial for a wide range of scientific and practical applications. In this study, we employ a deep neural network trained on density functional theory data to investigate the dielectric properties of liquid water at room temperature across a pressure range of 0.1–1000 MPa. We observe a nonlinear increase in the static dielectric constant ɛ 0 with increasing pressure, a trend that is qualitatively consistent with experimental observations. This increase in ɛ 0 is primarily attributed to the increase in water density under compression, which enhances collective dipole fluctuations within the hydrogen-bonding network as well as the dielectric response. Despite the increase in ɛ 0 , our results reveal a decrease in the Kirkwood correlation factor G K with increasing pressure. Furthermore, this decrease in G K is attributed to pressure-induced structural distortions in the hydrogen-bonding network, which weaken dipolar correlations by disrupting the ideal tetrahedral arrangement of water molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

High pressure stability of β-Zr: no evidence for isostructural phase transitions

Isostructural transitions have been reported to occur in several pure elements; however, most of these have been disproven. Zr is one of those elements which remains controversial with two reports of an isostructural bcc-to-bcc transition at ~56–60 GPa at an ambient temperature and a more recent report proposing a second bcc-to-bcc transition at 110 GPa. Here, we report a detailed experimental and theoretical study of zirconium in the pressure region of the proposed isostructural transition(s). We conducted three room temperature static compression experiments using Ne as a pressure transmitting medium up to 80 GPa. We see no evidence for an isostructural transition finding a smooth compression curve for β-Zr. We determined the theoretical volume, elastic parameters, and Poisson’s ratio for β-Zr up to 717 GPa and no obvious anomalies are identified. Furthermore, our new results join the growing body of evidence that does not find evidence of isostructural transitions in β-Zr.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Low-temperature magnetic crossover in the topological kagome magnet TbMn 6 Sn 6

Magnetic topological phases of quantum matter are an emerging frontier in physics and materials science, of which kagome magnets appear as a highly promising platform. Here, we explore magnetic correlations in the recently identified topological kagome system TbMn6 S n 6 using muon spin rotation, combined with local field analysis and neutron diffraction. Our studies identify an out-of-plane ferrimagnetic structure with slow magnetic fluctuations which exhibit a critical slowing down below $T^{*}_{C1}$ ≃ 120 K and finally freeze into static patches with ideal out-of-plane order below T C1 ≃ 20 K. We further show that hydrostatic pressure of 2.1 GPa stabilises the static out-of-plane topological ferrimagnetic ground state in the whole volume of the sample. Therefore the exciting perspective arises of a magnetically-induced topological system whose magnetism can be controlled through external parameters. The present results will stimulate theoretical investigations to obtain a microscopic understanding of the relation between the low-temperature volume-wise magnetic evolution of the static c-axis ferrimagnetic patches and the topological electronic properties in TbMn 6 Sn 6 .

36 MATERIALS SCIENCE↗
DOE OSTI2020

Wash Penalty Factors: Insight into the Effects of Water Wash Down of Building Materials for Radionuclide/Nuclear (Rn) Decontamination - 20153

The release of radiological material to the urban environment can have a devastating socio-economic impact. In an urban release scenario, areas around the dispersal epicenter and any areas contaminated via atmospheric deposition may require extensive decontamination. Most recently, our group reported the decontamination efficacy of pressurized water washing of common porous building materials, and compared the penetration depth of the contaminations before and after exposure to pressurized tap water. Here, we continue evaluation of the decontamination efficacy of wash solutions based on potassium (K{sup +}) salt for cesium (Cs), strontium (Sr), and europium (Eu) contaminations on common building surfaces. The surfaces included: the cement used in concrete, the aggregate used in concrete, intact concrete, roadway asphalt, asphalt shingles, and latex paint. We deposited solutions of {sup 137}Cs, {sup 85}Sr, and {sup 152}Eu onto numerous common building materials and exposed these materials to a static bath or low-pressure flow of tap water, 0.1 M potassium chloride (KCl), and 0.5 M KCl. The decontamination efficacy and the depth profile for residual contamination were measured to determine the conditions under which applying a wash solution has benefit compared to physically removing the surface material. To aid in these analyses, we introduced a 'wash penalty factor' to quantify the degree to which contamination migrated into the bulk material by the action of the wash method. On asphalt, 70-80% of the radionuclides were found to be within 0.02 mm of the surface. Cs{sup +} bonded to negative charge sites on the surface of the mineral aggregate (used in concrete) so decontamination was improved by ion exchange with K{sup +}. Sr{sup 2+} is soluble and removed by water, while not bonding to aggregate or demonstrating solubility in the liquid asphalt. Eu{sup 3+} is precipitated and not removed in gentle wash but displays mobility within the pore space that suggests its presence as a colloid. Concrete is more porous than asphalt, and 80% of the radionuclides were within 0.2 mm of the surface for {sup 137}Cs and {sup 152}Eu and 50- 80% for {sup 85}Sr. On concrete, Cs{sup +} bonds similarly to asphalt. Sr{sup 2+} bonds to the cement or precipitates from the alkaline pore water. Eu{sup 3+} sorbs to the cement and then precipitates. In brick, the results for Cs{sup +} and Sr{sup 2+} suggested that diffusion of ions from deeper in the coupon was important. Eu{sup 3+} is removed poorly due to precipitation. We will explain and report example wash penalty factors that vary from 0 to > 1 for the various methods and the implications for deciding when to implement wash down methods. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Penetration of Fission Products Ions into Complex Solids and the Effect of Ionic Wash Methods

During washing of radiologically impacted building surfaces, penetration of radionuclide ions into complex solids associated with these surfaces may occur. This study investigates the penetration of Cs-137, Sr-85, and Eu-152 solutions into numerous common building materials and radionuclide behavior when these materials were exposed to a static bath or low-pressure flow of tap water, 0.1 M potassium chloride (KCl), and 0.5 M KCl. The decontamination efficacy and the depth profile for residual contamination were measured to determine the conditions under which applying a wash solution has benefit compared to physically removing the surface material. On asphalt, 70-80% of the radionuclides were found to be within 0.02 mm of the surface. Concrete is more porous than asphalt, and 80% of the radionuclides were within 0.2 mm of the surface for Cs-137 and Eu-152 and 50-80% for Sr-85. Water effectively removed all contaminants from hard nonporous surfaces. Finally, this paper illustrates that a wash penalty factor concept-defined as ratio of the depth at which 50% of the radioactivity is found in the washed sample divided by the depth at which 50% of radioactivity is found in the control-can serve as a way to quantify whether the wash method increases the depth at which contamination penetrates into the material and thus the material becomes more difficult to decontaminate.

building materials↗
DOE OSTI2022

The Preston-Tonks-Wallace (PTW) Model Parameterization of Al-6061 With Sesame EoS

In this report, we make a recommendation for the PTW model parameters for an aluminum alloy, Al 6061-T6 based on the quasi-static and split-Hopkin pressure bar experimental data, provided by the experimentalists in MST-8, LANL. Al 6061 is an aluminum alloy with magnesium and silicon, and the temper designation T6 means it has gone through heat treatment followed by quenching, cooling, and aging. (Note that T4 is naturally aged and T6, artificially.) We adopted the shear modulus and melt curve models that are necessary to parameterize the PTW model, from Sesame EoS. In the lack of those information on this particular aluminum alloy, we used what is available for pure aluminum.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Soft Matter Sample Environments for Time-Resolved Small Angle Neutron Scattering Experiments: A Review

With the promise of new, more powerful neutron sources in the future, the possibilities for time-resolved neutron scattering experiments will improve and are bound to gain in interest. While there is already a large body of work on the accurate control of temperature, pressure, and magnetic fields for static experiments, this field is less well developed for time-resolved experiments on soft condensed matter and biomaterials. We present here an overview of different sample environments and technique combinations that have been developed so far and which might inspire further developments so that one can take full advantage of both the existing facilities as well as the possibilities that future high intensity neutron sources will offer.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Dynamic high pressure phase transformation of ZrW 2 O 8

Phase transformations under high strain rates (dynamic compression) are examined in situ on ZrW 2 O 8 , a negative thermal expansion ternary ceramic displaying polymorphism. Amorphization, consistent with prior quasi-static measurements, was observed at a peak pressure of 3.0 GPa under dynamic conditions, which approximate those expected during fabrication. Evidence of partial amorphization was observed at lower pressure (1.8 GPa) that may be kinetically restrained by the short (<~150 ns) time scale of the applied high pressure. The impact of kinetics of pressure-induced amorphization from material fabrication methods is briefly discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Self-welding of Inconel 617 under high-pressure-high-temperature conditions for nuclear reactors

In response to continuously declining availability of fossil fuels, nuclear power has become an important alternative source of power generation. Growing application of nuclear power has relieved the shortage of electricity. However, it is also accompanied with new drawbacks, such as radioactive waste, and potential catastrophic consequences in case of major accidents. For nuclear power plants, severe accidents mostly originate from the reactor, making the reliability of the reactor of paramount importance to the overall safety of a nuclear power plant. Massive heat generation through nuclear fission/fusion and heat exchange render the whole reactor operating at extremely high temperatures (i.e., 900–1000 °C), which, in conjunction with large load from subsystems/ components made of special heavy alloys, renders the reactor under the risk of self-welding, a phenomenon that could lead to strong bonding between components and paralyze the operability of the nuclear reactor. This paper investigates the self-welding behavior of Inconel 617, a primary candidate nickel alloy for key components of the next generation gas cooled nuclear plant, inside a controlled atmospheric furnace with preset static load, simulating the high-pressure high-temperature conditions inside nuclear reactors. Therefore, test results show that Inconel 617 experiences self-welding through common oxide zone at the interface, and it has remarkable bonding strength, requiring 4114 N (57.15 MPa) and 4338 N (60.25 MPa) to break apart a mated sample pair, under an apparent contact pressure of 0.341 MPa after 50-h aging, in helium and air atmospheres, respectively. The higher oxygen presence in air results in slightly stronger oxide bond at the interface, compared to helium, and the bond strength increases with dwell time.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Femtosecond X-ray Diffraction of Laser-shocked Forsterite (Mg 2 SiO 4 ) to 122 GPa

The response of forsterite, Mg 2 SiO 4 , under dynamic compression is of fundamental importance for understanding its phase transformations and high-pressure behavior. Here, we have carried out an in situ X-ray diffraction study of laser-shocked polycrystalline and single-crystal forsterite from 19 to 122 GPa using the Matter in Extreme Conditions end-station of the Linac Coherent Light Source. Under laser-based shock loading, forsterite does not transform to the high-pressure equilibrium assemblage of MgSiO 3 bridgmanite and MgO periclase, as has been suggested previously. Instead, we observe forsterite and forsterite III, a metastable polymorph of Mg 2 SiO 4 , coexisting in a mixed-phase region from 33 to 75 GPa for both polycrystalline and single-crystal samples. Densities inferred from X-ray diffraction are consistent with earlier gas-gun shock data. At higher stress, the response is sample-dependent. Polycrystalline samples undergo amorphization above 79 GPa. For [010]- and [001]-oriented crystals, a mixture of crystalline and amorphous material is observed to 108 GPa, whereas the [100]-oriented forsterite adopts an unknown phase at 122 GPa. The first two sharp diffraction peaks of amorphous Mg 2 SiO 4 show a similar trend with compression as those observed for MgSiO 3 in both recent static- and laser-driven shock experiments. This study provides new insight into the transformation of forsterite under nanosecond-duration shock loading. This work emphasizes the importance of formation of metastable phases along the Hugoniot and adds to evidence that the 300-K single-crystal diamond anvil cell experiments have relevance for understanding structures formed under shock compression. In particular, the metastable phase forsterite III has now been shown to form under dynamic compression from 10s to 100s of nanoseconds as well as under 300-K static compression. Upon compression to higher pressures, Mg 2 SiO 4 transforms to an amorphous phase. These results have broad relevance for understanding the behavior of silicates under dynamic compression.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phase Transitions in (Mg,Fe) 2 SiO 4 Olivine under Shock Compression

The response of forsterite, Mg 2 SiO 4 , under dynamic compression is of fundamental importance for understanding its phase transformations and high-pressure behavior. Here, we have carried out an in situ X-ray diffraction study of laser-shocked polycrystalline and single-crystal forsterite from 19 to 122 GPa using the Matter in Extreme Conditions end-station of the Linac Coherent Light Source. Under laser-based shock loading, forsterite does not transform to the high-pressure equilibrium assemblage of MgSiO 3 bridgmanite and MgO periclase, as has been suggested previously. Instead, we observe forsterite and forsterite III, a metastable polymorph of Mg 2 SiO 4 , coexisting in a mixed-phase region from 33 to 75 GPa for both polycrystalline and single-crystal samples. Densities inferred from X-ray diffraction are consistent with earlier gas-gun shock data. At higher stress, the response is sample-dependent. Polycrystalline samples undergo amorphization above 79 GPa. For [010]- and [001]-oriented crystals, a mixture of crystalline and amorphous material is observed to 108 GPa, whereas the [100]-oriented forsterite adopts an unknown phase at 122 GPa. The first two sharp diffraction peaks of amorphous Mg 2 SiO 4 show a similar trend with compression as those observed for MgSiO 3 in both recent static- and laser-driven shock experiments. This study provides new insight into the transformation of forsterite under nanosecond-duration shock loading. This work emphasizes the importance of formation of metastable phases along the Hugoniot and adds to evidence that the 300-K single-crystal diamond anvil cell experiments have relevance for understanding structures formed under shock compression. In particular, the metastable phase forsterite III has now been shown to form under dynamic compression from 10s to 100s of nanoseconds as well as under 300-K static compression. Upon compression to higher pressures, Mg 2 SiO 4 transforms to an amorphous phase. These results have broad relevance for understanding the behavior of silicates under dynamic compression.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Causal mechanism of injection-induced earthquakes through the M w 5.5 Pohang earthquake case study

Causal mechanisms for fluid injection-induced earthquakes remain a challenge to identify. Past studies largely established spatiotemporal correlations. Here, we propose a multi-process causal mechanism for injection-induced earthquakes through a case study of the 2017 M w 5.5 induced earthquake near Pohang Enhanced Geothermal System, Korea, where detailed hydraulic stimulation and on-site seismicity monitoring data provide an unprecedented opportunity. Pore pressure modeling reveals that pore pressure changes initiate seismicity on critically stressed faults and Coulomb static stress transfer modeling reveals that earthquake interactions promote continued seismicity, leading to larger events. On the basis of these results, we propose the following causal mechanism for induced seismicity: pore pressure increase and earthquake interactions lead to fault weakening and ultimately triggering larger earthquakes later in the process. We suggest that it is prudent that pore pressure change, initial seismicity locations, and Coulomb static stress transfer from seismicity earlier in the sequence are assessed in real-time.

58 GEOSCIENCES↗
DOE OSTI2025

Observation of a mixed close-packed structure in superionic water

The study of superionic (SI) water has been a highly active research area since its theoretical prediction. Despite significant experimental and computational efforts, its melting curve and the stability of different oxygen lattices remain debated, impacting our understanding of SI ice’s peculiar transport properties. Experimental results at lower pressures show disagreement, whereas data at higher pressures are scarce due to the extreme challenges of such experiments. In this work, we present ultrafast X-ray diffraction results of water compressed by multiple shocks to pressures up to ~ 180 GPa. At pressures exceeding 150 GPa and temperatures around 2500 K, our diffraction patterns challenge the pure FCC-SI phase model, providing experimental evidence of the mixed close-packed superionic phase predicted by advanced ab initio calculations. At lower pressures, we observe simultaneous signatures of BCC and FCC structures within a pressure-temperature range consistent with some static-compression experiments, helping to resolve contradictory results in literature. These insights offer new constraints on the stability domains of SI phases and reveal detailed structural features, such as stacking faults. Our results advance the structural understanding of high-pressure SI ice to a level approaching that of ice I polymorphs, with potential implications for water-rich interiors of giant planets.

Andriambariarijaona, Leon [Centre National de la R↗
DOE OSTI2024

Invariant regimes of Spencer scaling law for magnetic compression of rotating FRC plasma

Abstract The scaling laws for the magnetic compression of a toroidally rotating field reversed configuration (FRC) have been investigated in this work. The magnetohydrodynamics (MHD) simulations of the magnetic compression on rotating FRCs employing the NIMROD code (Sovinec et al 2004 J. Comput. Phys. 195 355), are compared with the Spencer’s one-dimensional (1D) theory (Spencer et al 1983 Phys. Fluids 26 1564) for a wide range of initial flow speeds and profiles. The toroidal flow can influence the scalings directly through the alteration of the compressional work as also evidenced in the 1D adiabatic model, and indirectly by reshaping the initial equilibrium. However, in comparison to the static initial FRC equilibrium cases, the pressure and the radius scalings remain invariant for the magnetic compression ratio B w 2 / B w 1 up to 6 in presence of the initial equilibrium flow, suggesting a broader applicable regime of the Spencer scaling law for FRC magnetic compression. The invariant scaling has been proven a natural consequence of the conservation of angular momentum of both fluid and magnetic field during the dynamic compression process.

Ma, Yiming↗
DOE OSTI2020

Micromachined Piezoresistive-sensed Diaphragms for Infrasonic Monitoring

Micromachined, piezoresistive-sensed diaphragms are designed and fabricated specifically for infrasound sensing applications. Relatively large diaphragms, up to 6 mm × 6 mm, are fabricated to meet the high sensitivity requirements of infrasonic monitoring. A double-stack SOI wafer process is used, resulting in a streamlined two-mask process without the need for doping or ion-implantation. Pressure-sensitivities of diaphragms are studied using a custom static calibration set-up. Here, the piezoresistance of longitudinal and transverse resistors are studied over a large pressure range of ±5,500 Pa so that the linear and nonlinear response regions of diaphragms are observed. Measurements are compared against a nonlinear finite element simulation—shown to accurately predict the sensor’s behavior over a large response range.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Sealability Qualification of Material Extruded Zytel Gaskets at Extreme Temperatures

In this work, an in-depth qualification of additively manufactured Zytel for gasketing proton exchange membrane fuel cells (PEMFC’s) subject to extreme temperature conditions. The temperature cycling of the PEMFC from 55°C to 100°C accelerates the deterioration of these gaskets compared to that of conventional operation. The additive manufacturing process employed to print these gaskets is material extrusion using Zytel filament. In order to see the effects of the temperature of interest on the printed specimen, each specimen was thermally soaked and then charactered and tested according to ASTM standard F37B. ASTM F37B tests a materials ability to seal and maintain it while bearing both a compressive load and internal pressure load to simulate being in static operation. This process of thermally soaking and sealability testing is shown to show the validity of both this material and additive manufactured components for other applications as well. It is observed that soaking the gaskets at 100°C corrects some of the defects that are present after printing such as missing layers and small voids on the surface of the samples. This allowed for the hot soaked materials to perform better than the samples at room temperature and cold soaked.

Sealability↗
DOE OSTI2024

Phase stability of a eutectic high entropy alloy under extremes of pressures and temperatures

Additively manufactured high-entropy alloys are of interest because of their unique combination of high yield strength and large ductility achieved with far-from-equilibrium crystalline phases and micro/nanostructure morphology. We report on the phase transformation and thermal equation of state of the eutectic high-entropy alloy (EHEA) Al 18 Co 20 Cr 10 Fe 10 Ni 40 W 2 , produced by laser powder-bed fusion (L-PBF). The EHEA was studied in a large-volume Paris–Edinburgh cell using energy-dispersive x-ray diffraction to a pressure of 5.5 GPa and a temperature of 1723 K. Static compression studies in diamond anvil cells using angle-dispersive x-ray diffraction extended the high-pressure structural data to 317 GPa at ambient temperature. The initial dual-phase nanolamellar face-centered cubic (FCC) and body-centered cubic (BCC) structure of Al 18 Co 20 Cr 10 Fe 10 Ni 40 W 2 transforms into a single FCC phase under high pressure, with the BCC-to-FCC phase transformation completing at 9 ± 2 GPa. The FCC phase remained stable up to the highest pressure of 317 GPa. The measured thermal equation of state for the FCC phase of Al 18 Co 20 Cr 10 Fe 10 Ni 40 W 2 is presented up to 5.5 GPa and 1473 K. We observed melting of the EHEA at 1698 ± 25 K at a pressure of 5.5 GPa, and the recrystallized sample shows an increased fraction of the CsCl-type (B2) phase at ambient conditions following release from the high-pressure high-temperature state. The BCC-to-FCC phase transition completion pressure is correlated with the nanolamellae thickness of the BCC layer in this diffusion-less transformation at ambient temperature.

36 MATERIALS SCIENCE↗