Search NASA⌕ Search

SEARCH · Search NASA

Results for “Strakes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Effects of deflected thrust on the longitudinal aerodynamic characteristics of a close-coupled wing-canard configuration

The effects of power on the longitudinal aerodynamic characteristics of a close-coupled wing-canard fighter configuration with partial-span rectangular nozzles at the trailing edge of the wing were investigated. Data were obtained on a basic wing-strake configuration for nozzle and flap deflections from 0 deg to 30 deg and for nominal thrust coefficients from 0 to 0.30. The model was tested over an angle-of-attack range from -2 deg to 40 deg at Mach numbers of 0.15 and 0.18. Results show substantial improvements in lift-curve slope, in maximum lift, and in drag-due-to-lift efficiency when the canard and strakes have been added to the basic wing-fuselage (wing-alone) configuration. Addition of power increased both lift-curve slope and maximum lift, improved longitudinal stability, and reduced drag due to lift on both the wing-canard and wing-canard-strake configurations. These beneficial effects are primarily derived from boundary-layer control due to moderate thrust coefficients which delay flow separation on the nozzle and inboard portion of the wing flaps.

Yip, L. P.↗
NASA NTRS1978

Aerodynamic characteristics of a jet sheet vortex generator

A configuration concept for augmenting the lift capability of low aspect ratio, thin wings, typically used on fighter aircraft was investigated. The fluid strake concept uses a jet sheet formed by blowing from a series of small orifices located in the side of the fuselage ahead of the wing to generate a stable vortex flow over the wing at high angle of attack. The effect of the location of the fluid strake relative to the wing was investigated for three different designs of the in-line orifices using a half-span model tested in a 7 by 10 foot low speed tunnel. Based on the results of the low speed test, a jet sheet producing module was incorporated into a NASA general research fighter model and tested in the Langley 7 by 10 foot high speed tunnel to determine the effectiveness of the fluid strake as a lift-enhancement device in the high-speed maneuver regime. Tests were conducted over a Mach number range from 0.3 to 0.8, with a jet momentum coefficient range from 0 to 0.24. Significant lift increments resulted at the higher angles of attack and drag polars were improved.

Ziegler, H.↗
NASA NTRS1979

Recent theoretical developments and experimental studies pertinent to vortex flow aerodynamics, with a view towards design

Recent progress in a research program directed toward an improved vortex flow technology base was reviewed. Analysis methods for conical flow and analysis and design methods for nonconical flows are presented. Applications are made for a variety of planar, nonplanar, and interferring lifting surfaces. Several methods are shown to provide reasonable estimates of over-all forces and moments for simple wing planforms with the suction analogy method currently offering the most versatility for arbitrary configuration applications. For the prediction of surface loadings the free vortex sheet method being developed by Boeing is shown to have considerable promise and further development of this type of method is encouraged. A data base for ogee strake-wing configurations is summarized with an emphasis on the requirements for maximizing the interference lift. A strake planform design procedure is discussed and a first solution (gothic in planview) is integrated with a wing body. The data show the strake to exhibit expected stable vortex characteristics. It was found that, apart from increasing sweep, conically cambered delta wings developed drag levels approaching that of attached flow with increasing either the lift or the wing camber height, lastly, an approximate vortex flow design method, based on the suction analogy, is outlined and an example is given.

Lamar, J. E.↗
NASA NTRS1982

The use of linearized-aerodynamics and vortex-flow methods in aircraft design /invited paper/

This paper deals with selected linearized-aerodynamic and vortex-flow methods as applied to aircraft design problems at high subsonic speeds. In particular, the NASA Vortex Lattice and Modified Multhopp methods are the linearized techniques employed, and the suction analogy is used to provide estimates associated with vortex-flow aerodynamics. Many examples are given as to how researchers at Langley have used these methods to design the high subsonic, wing-mean-camber shapes for various configurations such as a supersonic transport, high-aspect-ratio transport, trapezoidal fighter wing, strake wing, tandem wing, joined wing, delta wing, and slender cranked wing. Many of these have been built, tested, and have had their data compared with theory. In addition, a technique for defining efficiently performing strake planforms for use in strake-wing combinations is discussed, and further improvements in wing design are outlined. The latter may be obtained by using higher-ordered linear panel methods as well as nonlinear-transonic methods.

Lamar, J. E.↗
NASA NTRS1986

Forebody vortex management for yaw control at high angles of attack

The yaw-control potential of deployable forebody strakes at angles of attack above the range of conventional rudder effectiveness has been investigated. The conformally-stored strakes when deployed force asymmetrical vortex shedding from the forebody, thereby generating a controlled yawing moment. The concept was explored through low-speed wind tunnel tests on a conical forebody in isolation and in a generic fighter configuration. Force and moment measurements on the complete model were supplemented with circumferential pressure and flow-visualization surveys on an isolated forebody, in order to gain insight into the vortex flow mechanisms resulting from forced asymmetrical separations and to quantify the obtainable yaw power at angles of attack to 80 deg. This preliminary, low-Reynolds-number study showed asymmetrically-deployed forebody strakes to have considerable yaw control potential, whose sensitivity to scale effects needs further investigation.

Rao, D. M.↗
NASA NTRS1993

Helicopter low-speed yaw control

A system for improving yaw control at low speeds consists of one strake placed on the upper portion of the fuselage facing the retreating rotor blade and another strake placed on the lower portion of the fuselage facing the advancing rotor blade. These strakes spoil the airflow on the helicopter tail boom during hover, low speed flight, and right or left sidewards flight so that less side thrust is required from the tail rotor.

Wilson, John C.↗
NASA NTRS1994

F/A-18 forebody vortex control. Volume 2: Rotary-balance tests

A rotary-balance wind tunnel test was conducted on a six percent model of the F/A-18 at the NASA Ames 7 X 10-Foot Low Speed Wind Tunnel. The data reduction was specially written for the test in National Instruments' LabVIEW. The data acquisition, reduction and analysis was performed with a Macintosh computer. The primary objective of the test was to evaluate the effectiveness of several forebody vortex control configurations in a rotary flow field. The devices that were found to be the most effective during the static tests (Volume 1) were investigated and included both mechanical and pneumatic configurations. The mechanical systems evaluated were small, single and dual, rotating nose tip strakes and a vertical nose strake. The jet blowing configuration used nozzles canted inboard 60 degrees. A two segment tangential slot was also evaluated. The different techniques were evaluated at angles of attack of 30 degrees, 45 degrees, 51 degrees, and 60 degrees. Sideslip and Reynolds number were varied for some of the configurations. All of the techniques proved to be effective in the rotating flow field. The vertical nose strake had the largest 'envelope' of effectiveness. Forebody vortex control provides large, robust yawing moments at medium to high angles of attack, even during combat maneuvers such as loaded roll.

Kramer, Brian R.↗
NASA NTRS1994

Water tunnel flow visualization study of a 4.4 percent scale X-31 forebody

A water-tunnel test of a 4.4 percent-scale, forebody-only model of the X-31 aircraft with different forebody strakes and nosebooms has been performed in the Flow Visualization Facility at the NASA Dryden Flight Research Center. The focus of the study was to determine the relative effects of the different configurations on the stability and symmetry of the high-angle-of-attack forebody vortex flow field. The clean, noseboom-off configuration resisted the development of asymmetries in the primary vortices through 70 deg angle of attack. The wake of the X-31 flight test noseboom configuration significantly degraded the steadiness of the primary vortex cores and promoted asymmetries. An alternate L-shaped noseboom mounted underneath the forebody had results similar to those seen with the configuration, enabling stable, symmetrical vortices up to 70 deg angle of attack. The addition of strakes near the radome tip along the waterline increased the primary vortex strength while it simultaneously caused the vortex breakdown location co move forward. Forebody strakes did not appear to significantly reduce the asymmetries in the forebody vortex field in the presence of the flight test noseboom.

Cobleigh, Brent R.↗
NASA NTRS1996

An Overview of the NASA F-18 High Alpha Research Vehicle

This paper gives an overview of the NASA F-18 High Alpha Research Vehicle. The three flight phases of the program are introduced, along with the specific goals and data examples taken during each phase. The aircraft configuration and systems needed to perform the disciplinary and inter-disciplinary research are discussed. The specific disciplines involved with the flight research are introduced, including aerodynamics, controls, propulsion, systems, and structures. Decisions that were made early in the planning of the aircraft project and the results of those decisions are briefly discussed. Each of the three flight phases corresponds to a particular aircraft configuration, and the research dictated the configuration to be flown. The first phase gathered data with the baseline F-18 configuration. The second phase was the thrust-vectoring phase. The third phase used a modified forebody with deployable nose strakes. Aircraft systems supporting these flights included extensive instrumentation systems, integrated research flight controls using flight control hardware and corresponding software, analog interface boxes to control forebody strakes, a thrust-vectoring system using external post-exit vanes around axisymmetric nozzles, a forebody vortex control system with strakes, and backup systems using battery-powered emergency systems and a spin recovery parachute.

Bowers, Albion H.↗
NASA NTRS2000

Exploratory Investigation of Aerodynamic Characteristics of Helicopter Tail Boom Cross-Section Models with Passive Venting

Two large-scale, two-dimensional helicopter tail boom models were used to determine the effects of passive venting on boom down loads and side forces in hovering crosswind conditions. The models were oval shaped and trapezoidal shaped. Completely porous and solid configurations, partial venting in various symmetric and asymmetric configurations, and strakes were tested. Calculations were made to evaluate the trends of venting and strakes on power required when applied to a UH-60 class helicopter. Compared with the UH-60 baseline, passive venting reduced side force but increased down load at flow conditions representing right sideward flight. Selective asymmetric venting resulted in side force benefits close to the fully porous case. Calculated trends on the effects of venting on power required indicated that the high asymmetric oval configuration was the most effective venting configuration for side force reduction, and the high asymmetric with a single strake was the most effective for overall power reduction. Also, curves of side force versus flow angle were noticeable smoother for the vented configurations compared with the solid baseline configuration; this indicated a potential for smoother flight in low-speed crosswind conditions.

Banks, Daniel W.↗
NASA NTRS1974

Effect of engine shroud configuration on the static aerodynamic characteristics of a 0.00563 scale 142-inch diameter solid rocket booster (SA10F)

A test of a 0.563 percent scale space shuttle Solid Rocket Booster (SRB) model, MSFC Model 449, was conducted in a trisonic wind tunnel. Test Mach numbers were 0.4, 0.6, 0.9, 1.2, 1.96, 3.48, 4.0, 4.45, and 4.96. Test angles-of-attack ranged from minus 10 degrees to 190 degrees. Test Reynolds numbers ranged from 3.0 million per foot to 8.6 million per foot. Test roll angles were 0, 11.25, 22.5, 45, and 90 degrees. In addition to the static stability evaluation of the primary SRB configuration, five parametric investigations were made: (1) effect of Reynolds number, (2) effect of engine shroud flare angle, (3) effect of engine shroud length, (4) effect of engine shroud strakes, and (5) effect of engine shroud strakes and trust vector control bottles.

Johnson, J. D.↗
NASA NTRS1974

Onset of aerodynamic side forces at zero sideslip on symmetric forebodies at high angles of attack

Selected results are presented from extensive wind-tunnel tests that include variations in axial and cross-sectional shape, fineness ratio, bluntness, strakes, and boundary-layer trips over a wide range of conditions (angles of attack to 90 deg, angles of sideslip to 30 deg, Reynolds numbers from subcritical to supercritical, and Mach numbers from 0.1 to 0.7). Pointed forebodies at zero sideslip can experience side forces as large as maximum normal forces. The angle of attack at the onset of side force can be correlated with nose angle and afterbody length. Furthermore, these side forces can be reduced or eliminated by bluntness or nose strakes.

Keener, E. R.↗
NASA NTRS1974

Experimental aerodynamic characteristics for a cylindrical body of revolution with various noses at angles of attack from 0 deg to 58 deg and Mach numbers from 0.6 to 2.0

An experimental investigation was conducted to determine the effect of forebody geometry, a grit ring around the nose, Reynolds number, Mach number, and angle of attack on the aerodynamic characteristics of a body of revolution. Aerodynamic force and moment characteristics were measured for a cylindrical body with tangent ogive noses of fineness ratio 2.5, 3.0, 3.5, and 5.0. The cylindrical body was tested with an ogive nose having a rounded tip and an ogive nose with two different nose strake arrangements. Aerodynamic configurations were tested at various Mach numbers, angles of attack, and Reynolds numbers. The data demonstrate that the aerodynamic characteristics for a body of revolution can be significantly affected by changes in nose fineness ratio, nose bluntness, Reynolds number, Mach number, and, of course, angle of attack. Nose strakes increased the normal forces but had little effect on the side forces that developed at subsonic Mach numbers for alpha greater than about 25. A grit ring around the nose had little or no effect on the aerodynamic characteristics.

Jorgensen, L. H.↗
NASA NTRS1977

Low-speed wind tunnel investigation of an advanced supersonic cruise arrow-wing configuration

A preliminary assessment of possible means for improving the low speed aerodynamic characteristics of advanced supersonic cruise arrow wing configurations and to extend the existing data base of such configurations has been made. Principle configuration variables included wing-leading and trailing-edge flap deflection, fuselage nose strakes, and engine exhaust nozzle deflection. Results showed that deflecting the wing leading edge apex flaps downward provided improved longitudinal stability but resulted in reduced directional stability. The model exhibited relatively low values of directional stability over the operational angle of attack range and experienced large asymmetric yawing moments at high angles of attack. The use of nose strakes was found to be effective in increasing the directional stability and eliminating the asymmetric yawing moment.

Coe, P. L., Jr.↗
NASA NTRS1978

Subsonic longitudinal and lateral-directional static aerodynamic characteristics of a general research fighter configuration employing a jet sheet vortex generator

A configuration concept for developing vortex lift, which replaces the physical wing strake with a jet sheet generated fluid strake, was investigated on a general research fighter model. The vertical and horizontal location of the jet sheet with respect to the wing leading edge was studied over a momentum coefficient range from 0 to 0.24 in the Langley 7- by 10-foot high speed tunnel over a Mach number range from 0.3 to 0.8. The angle of attack range studied was from -2 to 30 deg at sideslip angles of 0, -5, and 5 deg. Test data are presented without analysis.

Huffman, J. K.↗
NASA NTRS1978

Low-speed aerodynamic characteristics from wind-tunnel tests of a large-scale advanced arrow-wing supersonic-cruise transport concept

Tests have been conducted to extend the existing low speed aerodynamic data base of advanced supersonic-cruise arrow wing configurations. Principle configuration variables included wing leading-edge flap deflection, wing trailing-edge flap deflection, horizontal tail effectiveness, and fuselage forebody strakes. A limited investigation was also conducted to determine the low speed aerodynamic effects due to slotted training-edge flaps. Results of this investigation demonstrate that deflecting the wing leading-edge flaps downward to suppress the wing apex vortices provides improved static longitudinal stability; however, it also results in significantly reduced static directional stability. The use of a selected fuselage forebody strakes is found to be effective in increasing the level of positive static directional stability. Drooping the fuselage nose, which is required for low-speed pilot vision, significantly improves the later-directional trim characteristics.

Smith, P. M.↗
NASA NTRS1978

Low-speed aerodynamic characteristics of a 0.08-scale YF-17 airplane model at high angles of attack and sideslip

Data were obtained with and without the nose boom and with several strake configurations; also, data were obtained for various control surface deflections. Analysis of the results revealed that selected strake configurations adequately provided low Reynolds number simulation of the high Reynolds number characteristics. The addition of the boom in general tended to reduce the Reynolds number effects.

Petroff, D. N.↗
NASA NTRS1980

Stall/spin flight results for the remotely piloted spin research vehicle

The unmanned, remotely piloted, unpowered, spin research vehicle was used to evaluate the effects of the nose boom and of a wind tunnel-designed nose strake on the vehicle's stall/spin characteristics. The flight-determined directional stability derivatives and the attempted spin entries indicated that the vehicle with a nose strake had increased resistance to departure and spin. The acquisition of high quality steady spin data for this vehicle was made possible by the remotely piloted technique. The zero control smooth spin modes were found to be highly repeatable for a given configuration and to vary with forebody configuration. Several spin recovery techniques, including a nose parachute, are also evaluated.

Iliff, K. W.↗