Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Evaluation Of Automated Low-Field Nuclear Magnetic Resonance (NMR) Relaxometry For Analysis Of Silicone Polymers

Screening studies and Design of Experiments (DoE) were performed to evaluate measurement variation of a new, non-destructive Nuclear Magnetic Resonance (NMR) test system designed to assess age-induced degradation of Outer Pressure Pads (OPP). The test method and results from 54,275 measurements are described. A reduction in measurement error was obtained after metal support struts were replaced with plastic support struts adjacent to the front position of the test chamber. However, remaining interference and a lack of detecting any age-related degradation prevent the use of the NMR system as a non-destructive surveillance test for OPPs. A cursory evaluation of the system with cellular silicone samples obtained more uniform results with increased error as measurements approached the sample’s edge.

36 MATERIALS SCIENCE↗

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 8 - Raw Data

Sequences 8 and 9: Downwind Sonics (F,P) and Downwind Sonics Parked (P) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 60° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM during Sequence 8, but it was parked during Sequence 9. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. Sonic anemometers were mounted on a strut downwind of the turbine. The strut was mounted to the T-frame, which was rotated to align the anemometers aft of the 9% and 49% radius locations at hub height. Because of this configuration, the tunnel balance data are considered invalid. Sequence 9 was designed to compare the downwind sonic anemometer readings with the upwind sonic anemometers without interference from the turbine. The rotor was parked with the instrumented blade at 0° azimuth. All pressure measurements obtained in Sequence 9 are invalid because sufficient time for temperature stabilization did not occur, thus all associated data values were flagged as not applicable by setting the measured values in the data file to 0.0000 Pa. This test is further described in Appendix G.

17 WIND ENERGY↗

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 9 - Raw Data

Sequences 8 and 9: Downwind Sonics (F,P) and Downwind Sonics Parked (P) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 60° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM during Sequence 8, but it was parked during Sequence 9. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. Sonic anemometers were mounted on a strut downwind of the turbine. The strut was mounted to the T-frame, which was rotated to align the anemometers aft of the 9% and 49% radius locations at hub height. Because of this configuration, the tunnel balance data are considered invalid. Sequence 9 was designed to compare the downwind sonic anemometer readings with the upwind sonic anemometers without interference from the turbine. The rotor was parked with the instrumented blade at 0° azimuth. All pressure measurements obtained in Sequence 9 are invalid because sufficient time for temperature stabilization did not occur, thus all associated data values were flagged as not applicable by setting the measured values in the data file to 0.0000 Pa. This test is further described in Appendix G.

17 WIND ENERGY↗

Acute Stent-Induced Endothelial Denudation: Biomechanical Predictors of Vascular Injury

Recent concern for local drug delivery and withdrawal of the first Food and Drug Administration-approved bioresorbable scaffold emphasizes the need to optimize the relationships between stent design and drug release with imposed arterial injury and observed pharmacodynamics. In this study, we examine the hypothesis that vascular injury is predictable from stent design and that the expanding force of stent deployment results in increased circumferential stress in the arterial tissue, which may explain acute injury poststent deployment. Using both numerical simulations and ex vivo experiments on three different stent designs (slotted tube, corrugated ring, and delta wing), arterial injury due to device deployment was examined. Furthermore, using numerical simulations, the consequence of changing stent strut radial thickness on arterial wall shear stress and arterial circumferential stress distributions was examined. Regions with predicted arterial circumferential stress exceeding a threshold of 49.5 kPa compared favorably with observed ex vivo endothelial denudation for the three considered stent designs. In addition, increasing strut thickness was predicted to result in more areas of denudation and larger areas exposed to low wall shear stress. We conclude that the acute arterial injury, observed immediately following stent expansion, is caused by high circumferential hoop stresses in the interstrut region, and denuded area profiles are dependent on unit cell geometric features. Such findings when coupled with where drugs move might explain the drug–device interactions.

Conway, Claire↗

Performance of a Prototype Heliostat Having a Twisting Mechanism to Maintain Focus Throughout the Day

A prototype heliostat has been designed and built with a rectangular reflector whose shape is altered automatically through the day, to maximize concentration at the receiver. The shape changes needed to form solar disc images, which give the highest possible concentration, can be realized by twisting the reflector from its corners, provided that a target-oriented, dual-axis mount is used. Then a cam mechanism connected to the second (cross) axis drive, turning with the angle of incident sunlight, may be used to twist the reflector as needed. Our prototype reflector comprises a single glass mirror, 2.4 m x 3.3 m, attached to a steel frame. Four diagonal back struts extend from the central mechanism out to the rectangular frame corners. The glass mirror of the prototype is attached to the steel frame by 58 screw actuators. Before twisting the frame, the glass shape is adjusted to the biconic shape needed to form a 1 m diameter disc image on a 113 m distant target when sunlight is incident at 60°. To form disc images over the full range of angles of incidence from 0° (normal incidence) to 70°, the struts push the corners up and down by up to 17 mm. A reflectometry metrology system has been used to set the 58 adjustment screws for the initial shape to an accuracy of ≤ 0.6 mrad, and to measure the accuracy of the different twisted shapes. The prototype will be tested at NSTTF early next year.

14 SOLAR ENERGY↗

Multiple piece turbine airfoil

A turbine airfoil, such as a rotor blade or a stator vane, for a gas turbine engine, the airfoil formed as a shell and spar construction with a plurality of dog bone struts each mounted within openings formed within the shell and spar to allow for relative motion between the spar and shell in the airfoil chordwise direction while also forming a seal between adjacent cooling channels. The struts provide the seal as well as prevent bulging of the shell from the spar due to the cooling air pressure.

Kimmel, Keith D↗

Variable volume combustor with aerodynamic fuel flanges for nozzle mounting

The present application provides a combustor for use with a gas turbine engine. The combustor may include a number of micro-mixer fuel nozzles and a fuel injection system for providing a flow of fuel to the micro-mixer fuel nozzles. The fuel injection system may include a number of support struts supporting the fuel nozzles and for providing the flow of fuel therethrough. The fuel injection system also may include a number of aerodynamic fuel flanges connecting the micro-mixer fuel nozzles and the support struts.

33 ADVANCED PROPULSION SYSTEMS↗

Additive Manufacturing at LANL: Advanced Characterization to Explore the Science of a New Manufacturing Method

Additive manufacturing (AM), or three-dimensional (3D) printing as it is more commonly known, is defined as the process of joining materials and creating objects by melting, sintering, or fusing material in a layer-by-layer fashion coordinated via 3D model data.1 Subtractive, or traditional, manufacturing methodologies often consist of machining/removing material—like a sculptor—or forming material through the application of pressure—like a potter. Conversely, in an AM process, material is added in individual volume elements and built up in a way similar to interlocking building blocks, but with volume elements that are typically the size of a grain of sand. The additive process often involves less waste when compared to subtractive techniques because material is only added when and where it is needed. Adjustments to the final structure are relatively straightforward and can be simply achieved by adjusting the 3D computer model. This makes the technology much more flexible than traditional, subtractive techniques where new tooling or forming equipment is usually needed to accommodate design changes. Also, the AM processes are beneficial because they permit the fabrication of unique geometries, such as miniaturized metal lattice structures, that cannot be achieved using traditional techniques. An example of a metal lattice structure is the Eiffel Tower with its Figure 1. Schematic showing required linkages between experimental and modeling thrusts in order to achieve science-based qualification. Arrows showing linkages are color-coded according to the funded projects listed. geometric, interconnecting struts that reduce the overall weight of the tower while maintaining strength. In AM, the size of the struts can be made smaller than the diameter of a human hair, which further reduces weight while maintaining strength—a combination of properties that can benefit many applications.

36 MATERIALS SCIENCE↗

Lattice microfluidics

An engineered unit cell is disclosed for flowing a fluid therethrough in three dimensions. The unit cell may have a substrate with a plurality of flow channels around and between struts formed within the substrate. The struts may each be formed with a desired shape and orientation within the substrate to achieve a desired degree of fluid flow through the flow channels, in each of one of three dimensions, through the unit cell.

Deotte, Joshua R.↗

Stent with expandable foam

A system comprising first, second, and third shape memory polymers (SMPs); wherein (a) the first SMP is a biodegradable open cell foam that includes a first channel; (b) the second SMP includes a second channel and is included in the first channel; (c) the foam is in a first state and is configured to expand to a second state, radially outward from the second foam, in response to thermal stimulus; (d) the third SMP is between the first and second SMPs and includes a stent having a first strut that includes the third SMP and a second strut that includes the third SMP; and (e) each of the first, second, and third SMPs is coupled to a wire.

Wilson, Thomas S.↗

Reaching For New Physics With MeV-scale Reconstruction In The MicroBooNE LArTPC Neutrino Detector

Large neutrino liquid argon time projection chamber (LArTPC) experiments can broaden their physics reach by reconstructing MeV-Scale energy depositions, or blips, in their data. We demonstrate new calorimetric and particle discrimination capabilities at the MeV scale using reconstructed blips in MicroBooNE LArTPC data at Fermilab. A concentration of low-energy ($<$3 MeV) blips is observed around fiberglass mechanical support struts along the TPC edges, with spectral features consistent with the Compton edge of the 2.614 MeV $^{208}$Tl decay $\gamma$ ray. With these features we perform the electron energy scale calibration to few-percent precision and yield the specific activity of $^{208}$Tl in the struts, $(11.7 \pm 0.2 \text{(stat)} \pm 2.8 \text{(syst)})$ Bq/kg. Using cosmogenic blips above 3 MeV, we demonstrate the ability of large LArTPCs to discriminate low-energy proton and electron depositions. An enriched low-energy proton sample selected with this technique is smaller in data than in dedicated CORSIKA simulations, pointing to possible mismodeling in CORSIKA incident cosmic fluxes or Geant4 particle transport. These methods are applied to MicroBooNE's inclusive single-photon search, which reported a 2.2$\sigma$ excess below 600 MeV in shower energy for events with no reconstructed protons. By identifying and classifying blips near single-photon events selected by the WireCell reconstruction framework, a more comprehensive labeling of nearby hadronic activity is established: blips upstream of the shower axis indicate previously unidentified final-state protons, while elevated blip counts at wide angles signal final-state neutrons. Taken together with MiniBooNE's long-standing low-energy excess (LEE) and MicroBooNE electron-like and sterile neutrino searches disfavored as possible explanations of the MiniBooNE anomaly, this analysis motivates an expanded exploration of the single-photon channel in Fermilab's short-baseline LArTPC program. This thesis documents the current status of this enhanced analysis, which will form a key part of MicroBooNE's final low-energy-excess results.

Andrade Aldana, Diego Armando [IIT, Chicago (main)↗

Quick torque coupling

A coupling for mechanically connecting modular tubular struts of a positioning apparatus or space frame, comprising a pair of toothed rings (10, 12) attached to separate strut members (16), the teeth (18, 20) of the primary rings (10, 12) mechanically interlocking in both an axial and circumferential manner, and a third part comprising a sliding, toothed collar (14) the teeth (22) of which interlock the teeth (18, 20) of the primary rings (10, 12), preventing them from disengaging, and completely locking the assembly together. A secondary mechanism provides a nesting force for the collar, and/or retains it. The coupling is self-contained and requires no external tools for installation, and can be assembled with gloved hands in demanding environments. No gauging or measured torque is required for assembly. The assembly can easily be visually inspected to determine a "go" or "no-go" status. The coupling is compact and relatively light-weight. Because of it's triply interlocking teeth, the connection is rigid. The connection does not primarily rely on clamps, springs or friction based fasteners, and is therefore reliable in fail-safe applications.

42 ENGINEERING↗

Hierarchical Composites Patterned via 3D Printed Cellular Fluidics

Additive manufacturing of freeform structures containing multiple materials with deterministic spatial arrangement and interactions remains a challenge for most 3D printing processes, due to complex fabrication tool requirements and limitations in printability of some material classes. Here, in this paper, a versatile method is reported to produce architected composites using the concept of cellular fluidics, in which lattices of unit cells are used as templating scaffolds to guide flowable infill materials in a programmed spatial pattern, upon which they are cured in place to produce a deterministically ordered multimaterial solid. The lattice design relies on the unit cell size, type, strut diameter, surface wetting, and distribution of cellular structures to control liquid flow and retention. Individual unit cells are tuned to achieve reliable infilling and combined into higher-order architectures to achieve multiscale composite materials with disparate mechanical properties, including those considered non-printable. Lattice design considerations for leveraging capillary phenomena and demonstrate several methods of patterning polymers in 3D-printed cellular fluidic structures are presented. The concept of tuning the compressive response of an architected composite using a flexible-elastomer as the lattice and a stiff-epoxy as the infill material is illustrated.

36 MATERIALS SCIENCE↗

Stable Thermotropic 3D and 2D Double Gyroid Nanostructures with Sub-2-nm Feature Size from Scalable Sugar–Polyolefin Conjugates

In this study, ultra-low molecular weight disaccharide–polyolefin conjugates with cellobiose, lactose and maltose head groups and atactic polypropene tails, such as 1, undergo a series of irreversible thermotropic order–order transitions with increasing temperature to provide nanostructured phases in the sequence: lamellar (L), hexagonal perforated lamellar (HPL), double gyroid (DG) and hexagonal cylindrical (C). The DG phase displays exceptional stability at ambient temperature and features two interpenetrating sugar domain networks having a sub-2-nm strut width and a lattice parameter, a DG , of 13.1 nm. The unique stability of this DG phase extends further within ultrathin films all the way down to the two-dimensional limit of 15 nm in which film thickness, l, is now less than the surface-oriented unit cell height, h DG . In addition to raising the fundamental question of what minimally constitutes a Schoen triply periodic minimal surface and DG lattice, these results serve to establish the class of sugar–polyolefin conjugates as a new material platform for nanoscience and nanotechnology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reconfigurable Two‐Dimensional DNA Lattices: Static and Dynamic Angle Control

Abstract Branched DNA motifs serve as the basic construction elements for all synthetic DNA nanostructures. However, precise control of branching orientation remains a key challenge to further heighten the overall structural order. In this study, we use two strategies to control the branching orientation. The first one is based on immobile Holliday junctions which employ specific nucleotide sequences at the branch points which dictate their orientation. The second strategy is to use angle‐enforcing struts to fix the branching orientation with flexible spacers at the branch points. We have also demonstrated that the branching orientation control can be achieved dynamically, either by canonical Watson–Crick base pairing or non‐canonical nucleobase interactions (e.g., i‐motif and G‐quadruplex). With precise angle control and feedback from the chemical environment, these results will enable novel DNA nanomechanical sensing devices, and precisely‐ordered three‐dimensional architectures.

Wang, Wen↗

Stable Thermotropic 3D and 2D Double Gyroid Nanostructures with Sub‐2‐nm Feature Size from Scalable Sugar–Polyolefin Conjugates

Abstract Ultra‐low molecular weight disaccharide–polyolefin conjugates with cellobiose, lactose and maltose head groups and atactic polypropene tails, such as 1 , undergo a series of irreversible thermotropic order–order transitions with increasing temperature to provide nanostructured phases in the sequence: lamellar ( L ), hexagonal perforated lamellar ( HPL ), double gyroid ( DG ) and hexagonal cylindrical ( C ). The DG phase displays exceptional stability at ambient temperature and features two interpenetrating sugar domain networks having a sub‐2‐nm strut width and a lattice parameter, a DG , of 13.1 nm. The unique stability of this DG phase extends further within ultrathin films all the way down to the two‐dimensional limit of 15 nm in which film thickness, l , is now less than the surface‐oriented unit cell height, h DG . In addition to raising the fundamental question of what minimally constitutes a Schoen triply periodic minimal surface and DG lattice, these results serve to establish the class of sugar–polyolefin conjugates as a new material platform for nanoscience and nanotechnology.

Nowak, Samantha R.↗

Reconfigurable Two-Dimensional DNA Lattices: Static and Dynamic Angle Control

Branched DNA motifs serve as the basic construction elements for all synthetic DNA nanostructures. However, precise control of branching orientation remains a key challenge to further heighten the overall structural order. Here in this study, we use two strategies to control the branching orientation. The first one is based on immobile Holliday junctions which employ specific nucleotide sequences at the branch points which dictate their orientation. The second strategy is to use angle-enforcing struts to fix the branching orientation with flexible spacers at the branch points. We have also demonstrated that the branching orientation control can be achieved dynamically, either by canonical Watson–Crick base pairing or non-canonical nucleobase interactions (e.g., i-motif and G-quadruplex). With precise angle control and feedback from the chemical environment, these results will enable novel DNA nanomechanical sensing devices, and precisely-ordered three-dimensional architectures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A projection-based method for topology optimization of structures with graded surfaces

Topology optimization (TO) is a generative design approach that is used to create new structures that are optimal for their purpose. Standard parameterizations of the TOproblem allow exploration of an arbitrarily complex design space, but must be constrained to ensure manufacturability; these constraints tend to be computationally expensive and intrusive to the design process. A relatively new parametrization of the TO problem uses geometry projection of known-manufacturable building blocksinto the design domain, but the existing library of building blocks compatible with projection is small. This project sought to expand this library with new shapes, and to determine whether theaddition of these new shapes could be used to design unit cells for micro-architected materials (MAMs) with improved stiffness-to-weight ratio compared with traditional designs,while retaining compatibility with additive manufacturing processes.Due to a reduction in scope, effort was focused on truss lattices with hollow, tapered, and curved struts. Hollowtruss lattices were found that outperform traditional designs like the octet truss in both stiffness and isotropy, as well as providing a decoupling between the stiffness and relative density. These new designs are expected to improve the performance of functionally graded structures in programmatic applications.

42 ENGINEERING↗