Search NASA⌕ Search

SEARCH · Search NASA

Results for “Styrenes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Synthesis of improved polyester resins

Eighteen aromatic unsaturated polyester prepolymers prepared by a modified interfacial condensation technique were investigated for their solubility in vinyl monomers and ability to provide high char yield forming unsaturated polyester resins. The best resin system contained a polyester prepolymer of phthalic, fumaric and diphenic acids reacted with 2,7-naphthalene diol and 9,9-bis(4-hydroxyphenyl)fluorene. This prepolymer is very soluble in styrene, divinyl benzene, triallyl cyanurate, diallyl isophthalate and methylvinylpyridine. It provided anaerobic char yields as high as 41 percent at 800 C. The combination of good solubility and char yield represents a significant improvement over state-of-the-art unsaturated polyester resins. The majority of the other prepolymers had only low or no solubility in vinyl monomers. Graphite composites from this prepolymer with styrene were investigated. The cause for the observed low shear strengths of the composites was not determined, however 12-week aging of the composites at 82 C showed that essentially no changes in the composites had occurred.

Mcleod, A. H.↗
NASA NTRS1986

The high-temperature oxidation of aromatic hydrocarbons

Chemical mechanisms of the atmospheric pressure, high-temperature (875-1500 K) gas-phase oxidation of benzene, toluene, ethylbenzene, and propylbenzene are described and discussed. Oxidation trends evident from turbulent flow reactor experiments serve as the basis for the mechanisms of the oxidation of benzene and alkylated aromatics. The potential effects of very high temperatures and pressures on the chemistry of oxidation of aromatics are described. The oxidation of benzene and phenyl radical has been found to proceed in a stepwise C6-C5-C4 sequence. Species profiles obtained from flow-reactor experiments suggest that the oxidation of benzene and phenyl radical follows the generalized route via phenoxy, cyclopentadienyl and butadienyl radical. The oxidation of the C4 species branches into multiple pathways that yield copious amounts of ethylene and acetylene. Certain major trends are evident: the alkylated aromatics on initial attack either form styrene, benzyl radical or benzene. The styrene reacts further to produce a benzyl radical or benzene. The oxidation of an alkylated aromatic hydrocarbon appears eventually to reduce to the oxidation of either phenyl radical or benzene.

Brezinsky, K.↗
NASA NTRS1985

The formation of small scale granularities in latex particles

A series of latices were synthesized using emulsifier-free emulsion copolymerization of styrene and sodium styrene sulfonic acid. The final latex particles display an internal granular structure which can be ascribed to the primary particles present in the early stages of particle growth. In these systems, the primary particles appear to have maintained their integrity during the swelling and growth stage.

Zukoski, C. F.↗
NASA NTRS2009

Tailoring Elastic Properties of Silica Aerogels Cross-Linked with Polystyrene

The effect of incorporating an organic linking group, 1,6-bis(trimethoxysilyl)hexane (BTMSH), into the underlying silica structure of a styrene cross-linked silica aerogel is examined. Vinyltrimethoxysilane (VTMS) is used to provide a reactive site on the silica backbone for styrene polymerization. Replacement of up to 88 mol 1 of the silicon from tetramethoxyorthosilicate with silicon derived from BTMSH and VTMS during the making of silica gels improves the elastic behavior in some formulations of the crosslinked aerogels, as evidenced by measurement of the recovered length after compression of samples to 251 strain. This is especially true for some higher density formulations, which recover nearly 100% of their length after compression to 251 strain twice. The compressive modulus of the more elastic monoliths ranged from 0.2 to 3 MPa. Although some of these monoliths had greatly reduced surface areas, changing the solvent used to produce the gels from methanol to ethanol increased the surface area in one instance from 6 to 220 sq m2/g with little affect on the modulus, elastic recovery, porosity, or density.

Nguyen, Baochau N.↗
DOE OSTI2021

Alkaline anion exchange membranes derived from diphenylethylene and co-monomer feedstock

The anion exchange membranes exhibit enhanced chemical stability and ion conductivity when compared with traditional styrene-based alkaline anion exchange membranes. A copolymer backbone is polymerized from a reaction medium that includes a diphenylalkylene and an alkadiene. The copolymer includes a plurality of pendant phenyl groups. The diphenyl groups on the polymer backbone are functionalized with one or more haloalkylated precursor substrates. The terminal halide from the precursor substrate can then be substituted with a desired ionic group. The diphenylethylene-based alkaline anion exchange membranes lack the .alpha.-hydrogens sharing tertiary carbons with phenyl groups from polystyrene or styrene-based precursor polymers, resulting in higher chemical stability. The ionic groups are also apart from each other by about 3 to 6 carbons in the polymer backbone, enhancing ion conductivity. These membrane are advantageous for use in fuel cells, electrolyzers employing hydrogen, ion separations, etc.

Lee, Sangwoo↗
DOE OSTI2023

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications: Preprint

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects of marine environments. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at Pacific Northwest National Laboratory's Marine Sciences Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗
DOE OSTI2023

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for highly loaded structures in harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects due to the marine environment. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at the Pacific Northwest National Laboratory's Marine and Coastal Research Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗
DOE OSTI2024

Alkaline anion exchange membranes derived from diphenylethylene and co-monomer feedstock

The anion exchange membranes exhibit enhanced chemical stability and ion conductivity when compared with traditional styrene-based alkaline anion exchange membranes. A copolymer backbone is polymerized from a reaction medium that includes a diphenylalkylene and an alkadiene. The copolymer includes a plurality of pendant phenyl groups. The diphenyl groups on the polymer backbone are functionalized with one or more haloalkylated precursor substrates. The terminal halide from the precursor substrate can then be substituted with a desired ionic group. The diphenylethylene-based alkaline anion exchange membranes lack the α-hydrogens sharing tertiary carbons with phenyl groups from polystyrene or styrene-based precursor polymers, resulting in higher chemical stability. The ionic groups are also apart from each other by about 3 to 6 carbons in the polymer backbone, enhancing ion conductivity. These membrane are advantageous for use in fuel cells, electrolyzers employing hydrogen, ion separations, etc.

Lee, Sangwoo↗
DOE OSTI2020

Crystal-growth-dominated fabrication of metal-organic frameworks with orderly distributed hierarchical porosity

Constructing architectures with hierarchical porosity has been widely considered as the most efficient way to bypass the problems related to slow mass transfer and inaccessibility of internal space in MOFs. Now, a crystal-growth-dominated strategy is proposed to fabricate hierarchically porous MOFs (HP-MOFs). When the crystal growth is dominated by the monomer attachment, the aggregation of nonionic surfactant or polymer can be easily captured and released during the crystal growth process, resulting in the formation and ordering hierarchical pores along the radial direction. Furthermore, owing to the accelerated mass diffusion and more exposed active sites of this design, HP-MOFs exhibited an enhanced catalytic efficiency in styrene oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2022

Small angle neutron scattering and lipidomic analysis of a native, trimeric PSI-SMALP from a thermophilic cyanobacteria

The use of styrene-maleic acid copolymers (SMAs) to produce membrane protein-containing nanodiscs without the initial detergent isolation has gained significant interest over the last decade. We have previously shown that a Photosystem I SMALP from the thermophilic cyanobacterium, Thermosynechococcus elongatus (PSI-SMALP), has much more rapid energy transfer and charge separation in vitro than detergent isolated PSI complexes. In this study, we have utilized small-angle neutron scattering (SANS) to better understand the geometry of these SMALPs. These techniques allow us to investigate the size and shape of these particles in their fully solvated state. Further, the particle's proteolipid core and detergent shell or copolymer belt can be interrogated separately using contrast variation, a capability unique to SANS. Here we report the dimensions of the Thermosynechococcus elongatus PSI-SMALP containing a PSI trimer. At ~1.5 MDa, PSI-SMALP is the largest SMALP to be isolated; our lipidomic analysis indicates it contains ~1300 lipids/per trimeric particle, >40-fold more than the PSI-DDM particle and > 100 fold more than identified in the 1JB0 crystal structure. Interestingly, the lipid composition to the PSI trimer in the PSI-SMALP differs significantly from bulk thylakoid composition, being enriched ~50 % in the anionic sulfolipid, SQDG. Finally, utilizing the contrast match point for the SMA 1440 copolymer, we also can observe the ~1 nm SMA copolymer belt surrounding this SMALP for the first time, consistent with most models of SMA organization.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Peeling back the layers: Investigating the effects of polyelectrolyte layering on surface structure and stability of oil-in-water nanoemulsions

Layer-by-layer deposition of polyelectrolytes is a useful technique for modifying surface functionalities. For drug delivery systems, alternating layers of biopolymers coat nanoemulsions, which house and protect the cargo until the time and destination of delivery. In this report we investigate molecular factors contributing to the stability and interfacial properties of nanoemulsions prepared by a co-adsorption of polymers poly(styrene sulfonate) and polyethylenimine (PEI), and surfactant dodecyltrimethylammonium bromide. We hypothesize the interplay between electrosteric and hydrophobic effects upon multi-polymer co-adsorption contributes to both macroscopic and molecular-level interfacial properties of nanoemulsions. To probe interfacial layering properties, we use vibrational sum frequency scattering spectroscopy with ζ -potential measurements to determine the adsorptive behavior and molecular conformational arrangement of the polymer layers. Complementing these interfacial studies are dynamic light scattering experiments measuring the nanoemulsion size distribution and polydispersity index over a 30-day period. Our light scattering, ζ -potential, and spectroscopic results of the nanoemulsion surface show that the duration of droplet stability and the degree of molecular orientation of adsorbed polymers can be tuned by surfactant concentration, PEI concentration, and pH. These results illustrate how molecular surface properties of multi-polymer coated nanoemulsions contribute to synergistic effects and droplet stability, enabling advancements in applications surrounding biopharmaceuticals, cosmetics, and food sciences.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Pyrolysis Reactions of (2-Chloroethyl)benzene

Pyrolysis of polyvinyl chloride (PVC) is considered an alternative to traditional, mechanical methods of recycling. However, there is insufficient research conducted on the thermal decomposition pathways of PVC, particularly the fate of chlorinated hydrocarbons generated during the chemical recycling process. One significant product from the pyrolysis of PVC is (2- chloroethyl)benzene. Using a hyperthermal tubular reactor and matrix-isolation FTIR techniques, the pyrolysis products of gasphase (2-chloroethyl)benzene were identified. Following pyrolysis at 1400 K, the FTIR spectra indicated the formation of HCl, styrene, phenylacetylene, benzene, vinylacetylene, acetylene, propyne, ethylene, and propargyl radical.

Aromatic compounds↗
DOE OSTI2022

Scalable Frontal Oligomerization: Insights from Advanced Mass Analysis

Linear oligomers of dicyclopentadiene (DCPD) are reactive precursors for thermoplastic and thermoset materials. Unlike the foul-smelling parent monomer, oligomers composed of DCPD are odorless. With appropriate modification of the end-group or backbone chemistry, telechelic DCPD oligomers have potential utility as cross-linkers and as macromonomer precursors for block and graft copolymers. Most existing methods to produce oligo-DCPD, however, require solvent, are relatively slow, and necessitate air-free techniques. Here we show that frontal ring-opening metathesis oligomerization (FROMO) of neat DCPD and other norbornene derivatives rapidly generates hundreds of grams of material in minutes with catalyst loadings of 0.5 mM. This energy-efficient catalytic process utilizes the heat generated by the reaction to self-propagate oligomerization throughout the liquid monomer. FROMO employs a terminal olefin (e.g., styrene) in which a cross-metathesis reaction (i.e., chain transfer) competes with ring-opening metathesis (i.e., propagation). Kendrick mass analysis enables rapid identification and assignment of all the chain-end types present and quantifies the degree of branching resulting from the infrequent cyclopentene ring-opening reaction. This analytical technique also detects oligomer species derived from trace impurities in the monomer or chain-transfer agent that are otherwise difficult to observe with other characterization methods. Here, the obtained oligomers possess well-defined chain-ends and molecular weight distributions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Selective Chemical Looping Combustion of Terminal Alkynes in Mixtures with Alkenes

The selective combustion of terminal alkynes in mixtures with alkenes is demonstrated during anaerobic reduction half-cycles on bulk bismuth oxide (Bi 2 O 3 ) as an approach to remove alkynes, which act as inhibitors in olefin polymerization. Bi 2 O 3 combusts phenylacetylene in styrene, 3-methylphenylacetylene in 3-methylstyrene, propyne in propylene, 1-hexyne in 1-hexene, and 1-octyne in 1-octene, with alkyne combustion selectivities exceeding 96%. Near unity reaction orders for hydrocarbon consumption during reduction half-cycles are consistent with combustion pathways initiated by rate-determining initial C–H activation, which drive selective alkyne combustion through intrinsic differences in the first-order rate constants for alkyne and alkene combustion rather than preferential adsorption of alkynes on Bi 2 O 3 surfaces. Computational assessments of initial C–H activation pathways for alkynes and alkenes on (010) α-Bi 2 O 3 surfaces using density functional theory illustrate that heterolytic transition states which form proton-carbanion pairs on Bi–O sites kinetically favor the activation of alkynes rather than alkenes due to differences in C–H bond acidity, and the barrier for heterolytic C–H activation is dictated in part by the sum of the molecular deprotonation energy and the energy to bind an R – carbanion to a Bi site in its transition-state geometry. Finally, these heterolytic reactivity channels during selective chemical looping combustion present novel routes for purifying olefin gas streams containing alkyne impurities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Plasmon-Assisted Electrochemical Epoxidation using Water as an Oxidant

Olefin epoxidation, an important industrial reaction, often uses hazardous oxidants, causing challenges in waste disposal. Here, we demonstrate the use of water as an oxidant by a plasmon-assisted electrochemical strategy. The electrocatalyst is comprised of a hybrid of a water oxidation catalyst, manganese oxide, and plasmonic gold nanoparticles. Visible-light irradiation of the electrocatalyst enhanced the epoxidation of 4-styrenesulfonate 5-fold as compared to dark conditions at the same temperature. From electrochemical analyses conducted under plasmon excitation conditions, complemented by real-time time-dependent density functional tight binding simulations, it is found that the plasmonic boost of the electrochemical styrene epoxidation is due to energetic holes generated by the excitation of localized surface plasmon resonances of gold nanoparticles. These photogenerated holes activate adsorbed water for oxidation and enhance the binding of 4-styrenesulfonate at interfacial sites. Here, this work demonstrates a proof of concept and establishes the mechanistic basis for plasmon-assisted activation of water as an O atom source for electrochemical epoxidations.

Gold↗
DOE OSTI2021

Breaking C-C Bonds via Electrochemically Mediated Hydrogen Atom Transfer Reactions

Cleaving inert SP3-SP3 carbon-carbon (C-C) bonds selectively remains a major challenge in organic chemistry and a main bottleneck in the chemical upcycling of recalcitrant polyolefin waste. Here, we present an electrochemical strategy using redox mediators to activate and break C-C bonds at room temperature and ambient pressure. Specifically, we use N-hydroxyphthalimide (NHPI) as a redox mediator that undergoes electrochemical oxidation to form the phthalimide-N-oxyl (PINO) radical to initiate hydrogen atom transfer (HAT) reactions with benzylic C-H bonds. The resulting benzylic carbon radical is readily captured by molecular oxygen to form a peroxy radical that decomposes into oxygenated C-C bond-scission fragments. This indirect, mediated approach for Csp3-Csp3 bond cleavage reduces the oxidation potential by > 1.2 V compared to the direct oxidation of the substrate, thereby eliminating deleterious side reactions, such as solvent oxidation, that may occur at high potentials. Studies with a bibenzyl model compound revealed a bifurcated reaction pathway following the initial HAT step. At a bibenzyl conversion of 61.0%, the C-C bond cleavage pathway generates benzaldehyde and benzoic acid products at 38.4% selectivity, and the C-H bond oxygenation pathway leads to 1,2-diphenylethanone and benzil products at 39.2% selectivity. Changes in reaction selectivity were investigated with various model compounds, including bibenzyl, 1,3-diphe-nylpropane, 1,4-diphenylbutane, and their derivatives. Product selectivity is correlated with the C-C bond strength of the reactant, with weaker C-C bonds favoring the C-C bond cleavage pathway. We also evaluated the mediated oxidation of oligo-meric styrene (Mn= 510 Da, OS510) which were converted into oxygenated products. Lastly, proof-of-concept depolymeriza-tion of polystyrene (PS, ~10,000 Da) into oxygenated monomers, dimers, and oligomers was demonstrated using NHPI-mediated oxidation.

benzoic acid↗
DOE OSTI2021

Engineering Graphene-Ceramic 3D Composite Foams by Freeze Drying

A 3D graphene foam produced by the chemical vapor deposition (CVD) technique is recognized as an effective nanofiller material, as it does not agglomerate in the matrix. Though CVD facilitates pristine graphene foam production, the method poses limitations in developing large-scale 3D graphene composite foams as advanced engineering materials. In this paper, a freeze-drying (FD) process is used to produce a composite 3D foam, which is a mixture of graphene nanoplatelet (GNP) and a low-temperature co-fired ceramic (LTCC). The freeze-dried GNP-LTCC reticulated 3D composite foam has an average pore size ranging from 70 to 100 μm. Pore size is varied by regulating the heat transfer rate during the freezing process using a thermally conductive aluminum (Al) mold and a thermally insulating acrylonitrile butadiene styrene (ABS) mold. Computational thermal modeling is used to visualize the heat transfer and its effect on foam pore size. Subsequently, a freeze-dried GNP-LTCC composite foam is embedded into the LTCC matrix to form a hierarchical assembly by a spark plasma technique without compromising the 3D structure of the FD foam. This study established that a simple, eco-friendly, and scalable processing methodology can produce advanced graphene-based 3D composite foams as the future tailorable nanofillers for designing multimatrix materials.

36 MATERIALS SCIENCE↗