Nitrene Photochemistry of Manganese N-Haloamides
Explore the source record for details and available documents.
Van Trieste III, Gerard P.↗
SEARCH · Search NASA
Results for “Styrenes”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Selective Sequential Depolymerization of Mixed Plastics Mediated by Photothermal Conversion
Chemical recycling of plastics into monomers is a promising strategy to achieve a circular economy. However, selective depolymerization methods for mixed plastics are still underdeveloped. Herein, we report a selective and sequential depolymerization strategy for mixed plastics, including poly(L-lactide) (PLLA), polystyrene (PS), and poly(ethylene terephthalate) (PET), using photothermal conversion. We were able to selectively depolymerize PLLA into L-lactide in the presence of PS and PET. Then, PS was selectively depolymerized to styrene, followed by the depolymerization of PET into its monomer. Our protocol was carried out in one pot without any additional purification of the unreacted plastics at each stage. This method was successfully applied to mixtures of post-consumer waste plastic.
carbon black↗
Boron‐polymer composites engineered for compression molding, foaming, and additive manufacturing
Abstract Boron (specifically 10 B) is the element of choice to shield thermal neutrons due to its large (n, α) cross‐section; however, very few polymer composites containing high boron concentrations are available. This study aimed to determine the maximum possible amount of boron that could be introduced into a polymer matrix. Diverse manufacturing techniques, ranging from additive manufacturing to compression molding, were employed to fabricate inks and filaments for 3D printing, foams, and flexible pads. Composites using siloxanes, poly(lactic acid), and acrylonitrile butadiene styrene containing up to 80 wt% boron were sucessufully fabricated. The addition of known plasticizers (polyethylene glycol) and reinforcing agents (carbon nanofibers and fumed silica) helped to overcome fabrication problems such as clogging of the printing nozzle or crumbling of compression molded parts. In addition, the thermal‐mechanical properties of these novel boron composites were determined and shown to vary according to boron concentration, presence of additives, and fabrication techniques utilized.
36 MATERIALS SCIENCE↗
Dual material fused filament fabrication of composite core‐shell structures with improved impact resistance and interfacial adhesion
The mechanical performance of parts produced by fused filament fabrication (FFF) has been limited due to the presence of voids and poor interlayer welding. Recent advancements in FFF have enabled the fabrication of void-free objects with strong interlayer welding through the use of semicrystalline polymer shells such as high-density polyethylene (HDPE) along with a high viscosity core polymer like acrylonitrile-butadiene-styrene (ABS). Furthermore, the zero-shear viscosity (η0) of ABS is three orders of magnitude higher than HDPE making the ABS-HDPE core-shell configuration preferable. ABS holds the shape by preventing bulk flow and part bending while HDPE promotes full surface contact across the layers. Most polymers, however, are immiscible which causes a weak weld line along the core-shell interface. Herein, maleic anhydride (MAH) is grafted to the butadiene segment of the ABS core thereby compatibilizing the interface with HDPE, improving the interfacial adhesion. Attenuated total reflectance-Fourier transform infrared spectroscopy was employed to confirm successful grafting. Using a custom-made die affording the core-shell structure, the ABS-g-MAH is shown to improve the impact resistance by 253% and 16% compared to neat HDPE and ABS specimens, respectively. Additionally, a 10% increase compared to the unmodified ABS-HDPE core-shell configuration is observed.
36 MATERIALS SCIENCE↗
Electrochemical Activation of C–C Bonds via Mediated Hydrogen Atom Transfer Reactions
Activating inert sp 3 -sp 3 carbon-carbon (C-C) bonds remains a major bottleneck in the chemical upcycling of recalcitrant polyolefin waste. Here, we use redox mediators to activate the inert C-C bonds. Specifically, we use N -hydroxyphthalimide (NHPI) as the redox mediator that is oxidized to phthalimide- N -oxyl (PINO) radical to initiate hydrogen atom transfer (HAT) reactions with benzylic C-H bonds. The resulting carbon radical is readily captured by molecular oxygen to form a peroxide that decomposes into oxygenated C-C bond-scission fragments. This indirect approach reduces the oxidation potential by > 1.2 V compared to the direct oxidation of the substrate. Studies with model compounds revealed the selectivity of C-C bond cleavage increases with decreasing C-C bond dissociation energy. With NHPI-mediated oxidation, oligomeric styrene ( M n = 510 Da, OS 510 ) and polystyrene (PS, ~10,000 Da) were converted into oxygenated monomers, dimers, and oligomers.
09 BIOMASS FUELS↗
Novel Co 5 Cluster Based Triazole Bridged Cobalt-Fluorophosphate: Synthesis, Structure, Magnetic and Heterogeneous Catalytic Epoxidation Studies
A novel triazole bridged cobalt fluorophosphate coordination polymer with the formula {Co 5 (1,2,4-triazole) 2 (OH) 2 (PO 3 F) 4 } n has been synthesized. Single crystal X-ray studies reveal that the compound comprises of Co 5 clusters which ultimately build the whole framework, here all cobalt centers are in octahedral geometry established from continuous shape analysis. All the cobalt centers are in Co(II) oxidation state and the results are supported by the bond valence sum (BVS) calculation. The sample has been characterized by single crystal X-ray, powder X-ray, FTIR and TGA analysis. The compound was tested for olefin catalysis performance and magnetism. Magnetization measurements reveal overall antiferromagnetic interactions among the Co(II) ions. The compound is very active in the catalytic transformation of olefins to their corresponding epoxides. In conclusion, catalytic epoxidation studies reveal that cyclohexene and styrene can be converted up to 97% with almost 65% selectivity of products with higher TON numbers.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Oxides and Nitrides with Asymmetric Pore Structure from Block Copolymer Co–Assembly and Non–Solvent Induced Phase Separation
Materials combining an asymmetric pore structure with mesopores everywhere enable high surface area accessibility and fast transport, making them attractive for e.g., energy conversion and storage applications. Block copolymer (BCP)/inorganic precursor co-assembly combined with non-solvent induced phase separation (NIPS) provides a route to materials in which a mesoporous top surface layer merges into an asymmetric support with graded porosity along the film normal and mesopores throughout. Here, the co-assembly and non-solvent-induced phase separation (CNIPS) of poly(isoprene)-b-poly(styrene)-b-poly(4-vinylpyridine) (ISV) triblock terpolymer and titanium dioxide (TiO 2 ) sol-gel nanoparticlesare reported. Heat-treatment in air results in free-standing asymmetric porous TiO 2 . Further thermal processing in ammonia results in free-standing asymmetric porous titanium nitride (TiN). processing changes alter structural membrane characteristics is demonstrated. Changing the CNIPS evaporation time results in various membrane cross-sections ( finger-like to sponge-like). Further, oxide and nitride material composition, crystallinity, and porosity are tuned by varying thermal processing conditions. Finally, thermal processing condition effects are probed on phase-pure asymmetric nitride membrane behavior using cyclic voltammetry to elucidate their influence, e.g., on specific capacitance. Results provide further insights into improving asymmetric and porous materials for applications including energy conversion and storage, separation, and catalysis and motivate a further expansion of CNIPS to other (in)organic materials.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Anisotropic thermal behavior of extrusion-based large scale additively manufactured carbon-fiber reinforced thermoplastic structures
Large format additive manufacturing (AM) enables rapid manufacturing of large parts and structures with minimum waste in material and energy. Extrusion-based AM deposition processes provide parts with highly anisotropic thermal properties, which are not typically reflected in textbook values for these materials. In order to develop accurate models that describe the directionally dependent thermal behavior of these materials in processing and service, accurate measurements of specific heat capacity and thermal conductivity are required. Here, this work characterizes, documents, and analyzes the effect of the anisotropic nature of the extrusion-based deposition process on the specific heat capacity and thermal conductivity of the resulting AM products. All measurements were made over a temperature range of 20–180°C using the transient plane source technique, also referred to as the hot disk technique. Three of the most commonly used large format AM feedstock materials that utilize carbon fiber reinforcement were examined in this work: acrylonitrile butadiene styrene, polyphenylene sulfide and polyphenylsulfone. Finally, these findings can serve as a thermal design/process guideline for future large format AM applications.
36 MATERIALS SCIENCE↗
Effect of network connectivity on the mechanical and transport properties of block copolymer gels
Establishing the independent tunability of transport and mechanical properties in polymer gels would significantly contribute to their implementation as transdermal drug delivery media, among other things. The work conducted herein uses facile changes in the formulation of physically crosslinked styrenic ABA/AB block copolymer organogels to alter their mechanical properties independently from the mass transport of an internally-loaded nanocarrier. Therefore, such independent tunability is made possible by altering the relative amounts of ABA triblock and AB diblock copolymers while holding total copolymer concentration fixed. Specifically, three series of gels each with a fixed total copolymer concentration (10, 20, or 30 wt%) comprised of varying triblock copolymer concentration are studied. Small angle x-ray scattering confirms that, at the nanoscale, only gel network connectivity changes within each series, while mechanical and release experiments show that increasing network connectivity leads to significant growth of gel moduli, but little change in nanocarrier release rate.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Electrolysis on a Chip with Tunable Thin Film Nanostructured PGM Electrocatalysts Generated from Self-Assembled Block Copolymer Templates
Self-assembled block copolymers are promising templates for fabricating thin film materials with tuned periodic feature sizes and geometry at the nanoscale. Here, a series of nanostructured platinum and iridium oxide electrocatalysts templated from poly(styrene)-block-poly(vinyl pyridine) (PSbPVP) block copolymers via an incipient wetness impregnation (IWI) pathway is reported. Both nanowire and nanocylinder electrocatalysts of varying feature sizes are assessed and higher catalyst loadings are achieved by the alkylation of the pyridine moieties in the PVP block prior to IWI. Electrocatalyst evaluations featuring hydrogen pump and water electrolysis demonstrations are carried out on interdigitated electrode (IDE) chips flexible with liquid supporting electrolytes and thin film polymer electrolytes. Notably, the mass activities of the nanostructured electrocatalysts from alkylated block copolymer templates are 35%–94% higher than electrocatalysts from non-alkylated block copolymer templates. Standing cylinder nanostructures lead to higher mass activities than lamellar variants despite their not having the largest surface area per unit catalyst loading demonstrating that mesostructure architectures have a profound impact on reactivity. Overall, IDE chips with model thin film electrocatalysts prepared from self-assembled block copolymers offer a high-throughput experimental method for correlating electrocatalyst nanostructure and composition to electrochemical reactivity.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Side-Chain Nanophase Separation Broadens the Double-Gyroid Stability Window in PS–PODMA Diblock Copolymers
Expanding access to bicontinuous network phases in block copolymers remains an important challenge because the double gyroid (DG) phase is usually stable only within a narrow composition window in conventional diblock copolymers. Here, we show that poly(styrene-block-octadecyl methacrylate) (PS-b-PODMA) exhibits an unusually broad DG window. Small-angle X-ray scattering measurements across a wide composition range reveal lamellar and hexagonally packed cylindrical phases at higher polystyrene fractions. In contrast, the DG phase appears over 0.22 ≤ fPS ≤ 0.35, with DG/BCC and DG/HEX coexistence near fPS = 0.18 and 0.40, respectively. This broad DG window is much wider than those reported for neat diblock copolymers and is not readily explained by conformational asymmetry alone. Wide-angle X-ray scattering detects a characteristic signature of nanophase separation within the PODMA-rich domains, indicating that side-chain ordering introduces an additional internal length scale. These results suggest that hierarchical side-chain nanophase separation modifies packing frustration and curvature selection, thereby broadening DG stability and providing a new molecular design strategy for stabilizing complex network morphologies.
Seko, Tamio↗
Interfacial Effects on the Dielectric Properties of Elastomer Composites and Nanocomposites
Elastomer-based composites and nanocomposites are discussed, with the emphasis on the filler and interfacial effects on their dynamics, and the resulting manifestation in their macroscopic dielectric or mechanical response. Specifically, selected polydimethylsiloxane (PDMS)/barium-titanate and styrene-butadiene rubber (SBR)/graphene oxide nanocomposites are discussed, as examples where controlled spatial distribution of filler (structured composites) gives rise to significantly different dielectric and thermomechanical behaviors. Also, ethylene–propylene–diene (EPDM)/carbon black (CB) composites are presented, as examples of systems that exhibit an abnormal temperature dependence of dielectric relaxation; and this response is discussed in the context of CB cluster polarization and quantified through a simple scaling model of the same. Finally, multi-filler EPDM/CB/ceramic elastomer nanocomposites are discussed, as examples of systems with antagonistic interfacial effects between conductive and dielectric fillers, as well as with strong interphase responses that can overwhelm the dielectric contributions from the fillers; in these systems, interphasial responses result in counter-intuitive dielectric behaviors and in strong deviations from standard design principles typically employed in the design of dielectric composite systems.
Li, Bo↗
Block copolymer-mediated synthesis of TiO2/RuO2 nanocomposite for efficient oxygen evolution reaction
Abstract An amphiphilic block copolymer, poly (styrene-2-polyvinyl pyridine-ethylene oxide), was used as a structure-directing and stabilizing agent to synthesize TiO 2 /RuO 2 nanocomposite. The strong interaction of polymers with metal precursors led to formation of a porous heterointerface of TiO 2 /RuO 2 . It acted as a bridge for electron transport, which can accelerate the water splitting reaction. Scanning electron microscopy, energy-dispersive X -ray spectroscopy, transmission electron microscopy, and X -ray diffraction analysis of TiO 2 /RuO 2 samples revealed successful fabrication of TiO 2 /RuO 2 nanocomposites. The TiO 2 /RuO 2 nanocomposites were used to measure electrochemical water splitting in three-electrode systems in 0.1-M KOH. Electrochemical activities unveil that TiO 2 /RuO 2 -150 nanocomposites displayed superior oxygen evolution reaction activity, having a low overpotential of 260 mV with a Tafel slope of 80 mVdec −1 . Graphical abstract
36 MATERIALS SCIENCE↗
Controlling substrate temperature with infrared heating to improve mechanical properties of large-scale printed parts
Additively manufactured parts made with polymer extrusion techniques can be 50-75% weaker in the z-direction (across layers) than in the x- and y-directions. This has been attributed to poor mobility of polymer chains and a low degree of entanglement across a cold deposition interface. This is particularly a challenge when printing large-scale parts, such as with the Big Area Additive Manufacturing (BAAM) system, because layer times can exceed several minutes. The current work presents a method for controlling the temperature of the substrate material on the BAAM just prior to deposition using infrared heating lamps. Additionally, long layer times were simulated by actively cooling the material following deposition of each layer. The effect of substrate temperature on the z-direction mechanical properties of 20% carbon fiber reinforced acrylonitrile butadiene styrene (ABS) was measured for an initial temperature ranging from 50 °C to 150 °C and a preheated temperature ranging from 150 °C to 220 °C. Infrared preheating proved to be very effective when applied to substrates that had cooled considerably, almost doubling the tensile strength and increasing the fracture toughness by a factor of 7x.
36 MATERIALS SCIENCE↗
High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology
Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.
36 MATERIALS SCIENCE↗
Characterizing material transitions in large-scale Additive Manufacturing
Integrating Multiple Materials (MM) into large-scale Additive Manufacturing (AM) is a key for various industrial applications wishing to incorporate site-specific properties into geometrically complex designs that are difficult to manufacture with traditional techniques. Printing with multiple materials is typically accomplished by using layers as natural material boundaries, but having the capability to switch between materials within a single layer without pausing would further expand MM possibilities. This study used Cincinnati Incorporated’s Big Area Additive Manufacturing (BAAM) system to explore material transitions with a novel dual-hopper that enables in-situ material blending of a pelletized feedstock. Constructing MM and functionally graded material (FGM) structures requires depositing a specific material composition at a specific geometric location to achieve a desired performance. Furthermore, accurately implementing this with the BAAM’s blended extrusion system requires a thorough understanding of the transition between distinct material compositions. This study characterizes a step-change transition between neat acrylonitrile butadiene styrene (ABS) and carbon fiber-reinforced ABS. Three distinct techniques were compared for analyzing the fiber content, and the transition zone between materials was characterized as a function of transition direction. The transition process was consistent to within 0.7 wt% carbon fiber variation between different layers and prints. The transition between materials was found to be directionally dependent, with ABS to CF/ABS having a transition length of 3.5 m compared to 3.2 m for CF/ABS to ABS. Furthermore, the transition from Material A to Material B was found to be repeatable with a possible variance in transition length of 0.3 m.
36 MATERIALS SCIENCE↗
The impact of infill percentage and layer height in small-scale material extrusion on porosity and tensile properties
We report material extrusion additive manufacturing is prone to introducing porosity within the structure due to the layer-by-layer construction using elliptical beads of material. This open porosity ultimately plays a role in determining the mechanical properties of printed parts. The shape, size, and amount of porosity within a printed part is influenced by a variety of factors, including nozzle diameter, infill percentage, layer height, raster orientation, and print speed. While several studies have investigated these and other parameters’ effects on mechanical performance and porosity, better understanding the interconnected relationships is crucial in balancing the various input parameters to achieve maximum strength. This work initially examined the influence of key print parameters (infill percentage and layer height) on the internal porosity of a printed Acrylonitrile Butadiene Styrene (ABS) part. Then, the print parameters and internal porosity were statistically correlated to final mechanical properties. Porosity was further classified as either open or closed to differentiate between connected voids in the mesostructure from isolated voids within the material itself. Mechanical performance increased with an increasing density and infill percentage, displaying a 224 % increase in elastic modulus and a 150 % increase in ultimate tensile strength. The contribution of layer height was found to be conditional upon the infill percentage.
3D Printing↗
Measuring thermomechanical response of large-format printed polymer composite structures via digital image correlation
Large-format additive manufacturing (LFAM) is a branch of additive manufacturing (AM) research with the ability to create large structures typically measuring several meters in scale. LFAM is advantageous for tooling applications, not only because it offers the ability to create complex geometries not easily made using subtractive manufacturing processes, but the cost savings of pelletized feedstock used by these systems result in larger parts printed at faster speeds than traditional AM systems. Fiber reinforced polymer (FRP) is a commonly used feedstock material in LFAM structures because it reduces the distortion experienced during printing. However, FRP introduces highly anisotropic thermomechanical properties and contributes to a nonhomogeneous microstructure that can result in critical distortion of dimensions during tooling. Measuring the global thermomechanical response of LFAM structures requires a more representative method that accounts for not only anisotropic properties but also the nonhomogeneous nature of the final part. This is where traditional techniques to measure thermomechanical response, such as thermomechanical analysis (TMA), fall short as they assume homogeneity. This study evaluated the coefficient of thermal expansion (CTE) of LFAM structures as measured by TMA as compared to a novel digital image correlation oven (DIC Oven) system. The LFAM structures were made from 20 % by weight carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS). TMA measurements showed significant variations in CTE across a single LFAM bead, confirming the need for a global technique that captures overall thermomechanical response. The CTE values measured using the DIC Oven compared well to average TMA values obtained from localized measurements across the sample. The DIC Oven was also used to quantify the effects of different layer orientations on thermomechanical properties, which cannot be easily captured using TMA. A predictive model was also developed by using localized TMA values across an LFAM bead to predict the overall thermomechanical response of an LFAM structure.
36 MATERIALS SCIENCE↗