Search NASA⌕ Search

SEARCH · Search NASA

Results for “Supersonic Airplane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

Preliminary Investigation of a New Type of Supersonic Inlet

A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions. The differences in drag can be eliminated for the design Mach number. Experimental results confirm the results of the theoretical analysis and show that pressure recoveries of 95 percent for Mach numbers of 1.33 and 1.52, 92 percent for a Mach number of 1.72, and 86 percent for a Mach number oof 2.10 are possible with the configurations considered. If the mass flow decreases, the total drag coefficient increases gradually and the pressure recovery does not change appreciably.

Ferri, Antonio↗
NASA NTRS1992

Results of a preliminary investigation of inlet unstart on a high-speed civil transport airplane concept

The aircraft design engineer of today is tasked with satisfying an increasing number of conflicting requirements. The fact that conflict in these requirements may be technically, economically, or politically motivated usually compounds the difficulty of determining the best solution to a design issue. In this regard, propulsion/airframe integration for supersonic airplanes must rank as one of the most challenging aspects of airplane design. For the cruise Mach numbers currently being considered for High-Speed Civil Transport (HSCT) airplanes, the inlet requirements of low drag, low bleed flow, and high pressure recovery appear to be best met with a mixed-compression design. Unfortunately, these desirable attributes come with a highly undesirable companion: the inlet unstart phenomenon. Concern over the effects of a mixed-compression inlet unstart on the vehicle dynamics of large, high-speed aircraft is not new; a comprehensive wind-tunnel study addressing the problem was published in 1962. Additional investigations of the problem were made throughout the United States SST program and the follow-on NASA program into the late 1970's. The current study sought to examine the magnitude of the problem in order to determine if an inlet unstart posed a potential hazard severe enough to preclude the use of mixed-compression inlets on proposed HSCT concepts.

Domack, Christopher S.↗
NASA NTRS1994

Atmospheric Disturbance Environment Definition

Traditionally, the application of atmospheric disturbance data to airplane design problems has been the domain of the structures engineer. The primary concern in this case is the design of structural components sufficient to handle transient loads induced by the most severe atmospheric "gusts" that might be encountered. The concern has resulted in a considerable body of high altitude gust acceleration data obtained with VGH recorders (airplane velocity, V, vertical acceleration, G, altitude, H) on high-flying airplanes like the U-2 (Ehernberger and Love, 1975). However, the propulsion system designer is less concerned with the accelerations of the airplane than he is with the airflow entering the system's inlet. When the airplane encounters atmospheric turbulence it responds with transient fluctuations in pitch, yaw, and roll angles. These transients, together with fluctuations in the free-stream temperature and pressure will disrupt the total pressure, temperature, Mach number and angularity of the inlet flow. For the mixed compression inlet, the result is a disturbed throat Mach number and/or shock position, and in extreme cases an inlet unstart can occur (cf. Section 2.1). Interest in the effects of inlet unstart on the vehicle dynamics of large, supersonic airplanes is not new. Results published by NASA in 1962 of wind tunnel studies of the problem were used in support of the United States Supersonic Transport program (SST) (White, at aI, 1963). Such studies continued into the late 1970's. However, in spite of such interest, there never was developed an atmospheric disturbance database for inlet unstart analysis to compare with that available for the structures load analysis. Missing were data for the free-stream temperature and pressure disturbances that also contribute to the unStart problem.

Tank, William G.↗
NASA NTRS1980

Overview of Boeing supersonic transport efforts, 1971 - 1979

Following cancellation of the United States Supersonic Transport program, the status of the technology was assessed carefully and emphasis was put on finding solutions for what were considered the major technical difficulties. In particular, work on the breakthroughs needed to advance the technology was emphasized. Currently, solutions to all major technical problems are identified. Depending on the subject, either the problem is no longer a concern or the steps needed to bring about a solution are mapped out clearly. Throughout the NASA SCR program, important strides were made in the identification of design advances which would greatly improve supersonic airplane fuel efficiency, noise, and other performance and cost affecting parameters. Furthermore, these efforts created an atmosphere in which it was possible for new ideas to flourish and positive inventions to take place such as the variable cycle engine and the blended fuselage. These technical gains show that, given availability of such technology, advanced supersonic transports could be developed that would be economically successful and environmentally acceptable.

Sigalla, A.↗
NASA NTRS1979

Elevated-temperature effects on strain gages on the YF-12A wing

A general study is made of the effects of structural heating on calibrated-strain-gage load measurements on the wing of a supersonic airplane. The primary emphasis is on temperature-induced effects as they relate to slope changes and thermal shifts of the applied load/strain relationships. These effects are studied by using the YF-12A airplane, a structural computer model, and subsequent analyses. Such topics as the thermal environment of the structure, the variation of load paths at elevated temperature, the thermal response characteristics of load equations, elevated-temperature load-measurement approaches, the thermal calibration of wings, and the correlation of strains are discussed. Ways are suggested to measure loads with calibrated strain gages in the supersonic environment.

Jenkins, J. M.↗
NASA NTRS1955

An Investigation of the Effects of Nose and Lip Shapes for an Underslung Scoop Inlet at Mach Numbers from 0 to 1.9

An experimental investigation was conducted to determine the performance characteristics an underslung nose-scoop air-induction system for a supersonic airplane. Five different nose shapes, three lip shapes, and two internal diffusers were investigated. Tests were made at Mach numbers from 0 to 1.9, angles of attack from 0 deg to approximately l5 deg, and mass-flow ratios from 0 to maximum obtainable. It was found that the underslung nose-scoop inlet was able to operate at Mach numbers from 0.6 to 1.9 over a large positive angle-of-attack range without adverse effects on the pressure recovery. Although there was no one inlet configuration that was markedly superior over the entire range of operating variables, the arrangement having a nose designed to give increased supersonic compression at low angles of attack, and a sharp lip (configuration designated N3L3) showed the most favorable performance characteristics over the supersonic Mach number range. Inlets with sizable lip radii gave satisfactory performance up to a Mach number of 1.5; however, as a result of an increase in drag, the performance of such inlets was markedly inferior to the sharp-lip configuration above Mach numbers of 1.5. Throughout the range of test Mach numbers all inlet configurations evidenced stable air-flow characteristics over the mass-flow range for normal engine operation. Analysis of the inlet performance on the basis of a propulsive thrust parameter showed that a fixed inlet area could be used for Mach numbers up to 1.5 with only a small sacrifice in performance.

NOSE CONE↗
NASA NTRS1975

Crack growth in Ti-8Al-1Mo-1V with real-time and accelerated flight by flight loading

Crack growth in Ti-8Al-lMo-lV was measured and calculated for real time and accelerated simulations of supersonic airplane loading and heating. Crack-growth rates calculated on the assumption that an entire flight could be represented by a single cycle predicted the experimental rates poorly. Calculated crack growth rates were slower than the experimental rates for all tests with flight-by-flight loading. For room temperature accelerated tests, the calculated rates agreed well with the experimental rates; but the calculations became progressively less accurate for progressively more complex test conditions (tests that included elevated temperature).

Imig, L. A.↗
NASA NTRS1975

Techniques for determining propulsion system forces for accurate high speed vehicle drag measurements in flight

As part of a NASA program to evaluate current methods of predicting the performance of large, supersonic airplanes, the drag of the XB-70 airplane was measured accurately in flight at Mach numbers from 0.75 to 2.5. This paper describes the techniques used to determine engine net thrust and the drag forces charged to the propulsion system that were required for the in-flight drag measurements. The accuracy of the measurements and the application of the measurement techniques to aircraft with different propulsion systems are discussed. Examples of results obtained for the XB-70 airplane are presented.

Arnaiz, H. H.↗
NASA NTRS1977

Advanced supersonic propulsion study, phase 4

Installation characteristics for a Variable Stream Control Engine (VSCE) were studied for three advanced supersonic airplane designs. Sensitivity of the VSCE concept to change in technology projections was evaluated in terms of impact on overall installed performance. Based on these sensitivity results, critical technology requirements were reviewed, resulting in the reaffirmation of the following requirements: low-noise nozzle system; a high performance, low emissions duct burner and main burner; hot section technology; variable geometry components; and propulsion integration features, including an integrated electronic control system.

Howlett, R. A.↗
NASA NTRS1978

Simplified sonic-boom prediction

Sonic boom overpressures and signature duration may be predicted for the entire affected ground area for a wide variety of supersonic airplane configurations and spacecraft operating at altitudes up to 76 km in level flight or in moderate climbing or descending flight paths. The outlined procedure relies to a great extent on the use of charts to provide generation and propagation factors for use in relatively simple expressions for signature calculation. Computational requirements can be met by hand-held scientific calculators, or even by slide rules. A variety of correlations of predicted and measured sonic-boom data for airplanes and spacecraft serve to demonstrate the applicability of the simplified method.

Carlson, H. W.↗
NASA NTRS1980

Future integrated design process

The design process is one of the sources used to produce requirements for a computer system to integrate and manage product design data, program management information, and technical computation and engineering data management activities of the aerospace design process. Design activities were grouped chronologically and explored for activity type, activity interface, data quantity, and data flow. The work was based on analysis of the design process of several typical aerospace products, including both conventional and supersonic airplanes and a hydrofoil design. Activities examined included research, preliminary design, detail design, manufacturing interface, product verification, and product support. The design process was then described in an IPAD environment--the future.

Meyer, D. D.↗
NASA NTRS1985

Active control landing gear for ground load alleviation

Results of analytical and experimental investigations of a series-hydraulic active control landing gear show that such a gear is feasible when using existing hardware and is very effective in reducing loads, relative to those generated by a conventional (passive year) gear, transmitted to the airframe during ground operations. Analytical results obtained from an active gear, flexible aircraft, take-off and landing analysis are in good agreement with experimental data and indicate that the analysis is a valid tool for study and initial design of series-hydraulic active control landing gears. An analytical study of a series-hydraulic active control main landing gear on an operational supersonic airplane shows that the active gear has the potential for improving the dynamic response of the aircraft and significantly reducing structural fatigue damage during ground operations.

Mcgehee, J. R.↗
NASA NTRS1993

Algorithm For Finer Resolution Of Position Of Shock

Algorithm computes streamwise position of terminal aerodynamic shock in inlet of engine of supersonic airplane. Signal representative of position of shock must be available to propulsion-control system of airplane to ensure proper operation of inlet. Algorithm computes position of shock with resolution much finer than spacing between transducers and requires neither increase in number of transducers nor other changes in pressure-measuring equipment.

Sajben, Miklos↗
NASA NTRS1953

An analysis of turbojet-engine-inlet matching

A method of presenting turbojet-engine air-flow requirements and inlet-system air-flow capacities in identical though independent parametric terms is developed. The application of the air-flow representation technique to the analysis of engine-inlet matching conditions is demonstrated. Several examples are presented to illustrate the application of the method to the explicit determination of inlet geometric variations required to improve the power-plant performance of supersonic airplanes.

Wyatt, Demarquis↗
NASA NTRS1952

Preliminary Investigation of a New Type of Supersonic Inlet

A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered a particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and, therefore, is practical for use on supersonic airplanes and missiles. Experimental results confirming the theoretical analysis give pressure recoveries which vary from 95 percent for Mach number 1.33 to 86 percent for number 2.00. These results were originally presented in a classified document of the NACA in 1946.

Ferri, Antonio↗
NASA NTRS1958

A Comparative Analysis of the Performance of Long-Range Hypervelocity Vehicles

Long-range hypervelocity vehicles are studied in terms of their motion in powered flight. Powered flight is analyzed for an idealized propulsion system which approximates rocket motors. Unpowered flight is characterized by a return to earth along a ballistic, skip, or glide trajectory. Only those trajectories are treated which yield the maximum range for a given velocity at the end of powered flight. Aerodynamic heating is treated in a manner similar to that employed previously by the senior authors in studying ballistic missiles (NACA rep. 1381), with the exception that radiant as well as convective heat transfer is considered in connection with glide and skip vehicles. As a final performance consideration, it is shown that on the basis of equal ratios of mass at take-off to mass at the end of powered flight, the hypervelocity vehicle compares favorably with the supersonic airplane for ranges in the neighborhood of and greater than one half the circumference of the earth. In the light of this and previous findings, it is concluded that the ballistic and glide vehicles have, in addition to the advantages usually ascribed to great speed, the attractive possibility of providing relatively efficient long-range flight.

Eggers, Alfred J , Jr↗
NASA NTRS1956

High-temperature oxidation and ignition of metals

A study of the high-temperature oxidation of several aircraft construction materials was undertaken to assess the possibility of ignition under high-temperature flight conditions.Tests have been made both in open and closed jets, and, in addition, the burning of metals has been observed under static conditions in a pressurized vessel containing either air, oxygen, or nitrogen. When heated in an atmosphere of oxygen or when heated and plunged into a supersonic airstream, titanium, iron, carbon steel, and common alloys such as 4130 were found to have spontaneous-ignition temperatures in the solid phase (below melting) and they melted rapidly while burning. Inconel, copper, 18-8 stainless steel, Monel, and aluminum could not be made to ignite spontaneously at temperatures up to melting with the equipment available. Magnesium ignited spontaneously in either type of test at temperatures just above the melting temperature.A theory for the spontaneous ignition of metals, based on the first law of thermodynamics, is presented. Good correlation was obtained between calculated spontaneous-ignition temperatures and values measured in supersonic jet tests. There appears at the present time to be no need for concern regarding the spontaneous ignition of Inconel, the stainless steels, copper, aluminum, or magnesium for ordinary supersonic airplane or missile applications where the material temperature is kept within ordinary structural limits or at least below melting. For hypersonic applications where the material is to be melted away to absorb the heat of convection, the results of the present tests do not apply sufficiently to allow a conclusion.

Hill, Paul R↗