Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL MOUNTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

An Analysis of the Impact of Extreme Attitude Operation on a Turbofan Engine in a Regional Jet Aircraft

The objective of this work is to characterize the variability in engine performance at extreme attitudes, resulting from the use of different standard control variables, evaluated at different points in the engine’s lifecycle. This paper describes the procedure used to create a dynamic model of an aft-mounted jet engine on a T-tail regional jet aircraft. This model enables simulation of engine operation at extreme attitudes. The model was subsequently evaluated at various altitudes, Mach numbers, and power settings over a range of angles of attack and sideslip, and deterioration levels. Each case was simulated using both fan speed and engine pressure ratio as the engine control variable. The results show that the wing has a very large impact on the engine operation, overwhelming other sources of variation.

loss of control - inflight↗
NASA NTRS2013

Wind Tunnel Investigation of Passive Vortex Control and Vortex-Tail Interactions on a Slender Wing at Subsonic and Transonic Speeds

A wind tunnel experiment was conducted in the NASA Langley 8-Foot Transonic Pressure Tunnel to determine the effects of passive porosity on vortex flow interactions about a slender wing configuration at subsonic and transonic speeds. Flow-through porosity was applied in several arrangements to a leading-edge extension, or LEX, mounted to a 65-degree cropped delta wing as a longitudinal instability mitigation technique. Test data were obtained with LEX on and off in the presence of a centerline vertical tail and twin, wing-mounted vertical fins to quantify the sensitivity of the aerodynamics to tail placement and orientation. A close-coupled canard was tested as an alternative to the LEX as a passive flow control device. Wing upper surface static pressure distributions and six-component forces and moments were obtained at Mach numbers of 0.50, 0.85, and 1.20, unit Reynolds number of 2.5 million, angles of attack up to approximately 30 degrees, and angles of sideslip to +/-8 degrees. The off-surface flow field was visualized in cross planes on selected configurations using a laser vapor screen flow visualization technique. Tunnel-to-tunnel data comparisons and a Reynolds number sensitivity assessment were also performed. 15.

Erickson, Gary E.↗
NASA NTRS1972

Dynamic stability derivatives at angles of attack from minus 5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails

An investigation was conducted in the Langley full-scale tunnel to determine the dynamic stability derivatives in pitch, roll, and yaw over an angle-of-attack range of -5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails. The study consisted of forced-oscillation tests of a 1/10-scale model of the airplane at a Reynolds number of 0.4 million based on the reference wing mean aerodynamic chord. Tests were conducted for wing sweep angles of 22 deg, 35 deg, 50 deg, and 68 deg, and the effects of the vertical and horizontal tails, wing leading-edge slats, nose-mounted canards, and frequency of the oscillation were also evaluated.

Grafton, S. B.↗
NASA NTRS1976

Aircraft-mounted crash-activated transmitter device

An aircraft crash location transmitter tuned to transmit on standard emergency frequencies is reported that is shock mounted in a sealed circular case atop the tail of an aircraft by means of a shear pin designed to fail under a G loading associated with a crash situation. The antenna for the transmitter is a metallic spring blade coiled like a spiral spring around the outside of the circular case. A battery within the case for powering the transmitter is kept trickle charged from the electrical system of the aircraft through a break away connector on the case. When a crash occurs, the resultant ejection of the case from the tail due to a failure of the shear pin releases the free end of the antenna which automatically uncoils. The accompanying separation of the connector effects closing of the transmitter key and results in commencement of transmission.

Manoli, R.↗
NASA NTRS1980

Experimental and analytical transonic flutter characteristics of a geared-elevator configuration

The flutter model represented the aft fuselage and empennage of a proposed supersonic transport airplane and had an all movable horizontal tail with a geared elevator. It was tested mounted from a sting in the transonic dynamics tunnel. Symmetric flutter boundaries were determined experimentally at Mach numbers from 0.7 to 1.14 for a geared elevator configuration (gear ratio of 2.8 to 1.0) and an ungeared elevator configuration (gear ratio of 1.0 to 1.0). Gearing the elevator increased the experimental flutter dynamic pressures about 20 percent. Flutter calculations were made for the geared elevator configuration by using two analytical methods based on subsonic lifting surface theory. Both methods analyzed the stabilizer and elevator as a single, deforming surface, but one method also allowed the elevator to be analyzed as hinged from the stabilizer. All analyses predicted lower flutter dynamic pressures than experiment with best agreement (within 12 percent) for the hinged elevator method. Considering the model as mounted from a flexible rather than rigid sting in the analyses, had only a slight effect on the flutter results but was significant in that a sting related vibration mode was identified as a potentially flutter critical mode.

Ruhlin, C. L.↗
NASA NTRS2018

Tri-Rotor Aircraft Capable of Vertical Takeoff and Landing and Transitioning to Forward Flight

Systems, methods, and devices provide a vehicle, such as an aircraft, with rotors configured to function as a tri-copter for vertical takeoff and landing ("VTOL") and a fixed-wing vehicle for forward flight. One rotor may be mounted at a front of the vehicle fuselage on a hinged structure controlled by an actuator to tilt from horizontal to vertical positions. Two additional rotors may be mounted on the horizontal surface of the vehicle tail structure with rotor axes oriented vertically to the fuselage. For forward flight of the vehicle, the front rotor may be rotated down such that the front rotor axis may be oriented horizontally along the fuselage and the front rotor may act as a propeller. For vertical flight, the front rotor may be rotated up such that the front rotor axis may be oriented vertically to the fuselage, while the tail rotors may be activated.

North, David D.↗
NASA NTRS1981

STOL capability impact on advanced tactical aircraft design

The design and technical issues affecting supersonic STOL development as an airbase attack fighter are discussed. An Air Force study has indicated that, from a weight and cost standpoint, the preferred directions will include two-dimensional nozzles with vectoring and thrust reversing capability. Take-off and landing requirements would determine other design features, and the use of a jump strut to enable landing maneuvers to be made at pitch angles which would normally drag the tail is detailed. The addition of a tip-mounted reaction control system is foreseen as necessary for roll control at the low aerodynamic speeds of STOL landing. A severe 700 ft landing distance design is outlined, and includes a lifting engine with bleed-air features to feed the reaction control system.

Krepski, R. E.↗
NASA NTRS1959

Low-Speed Measurements of Static and Oscillatory Lateral Stability Derivatives of a 1/5 Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

Force tests of the static and dynamic lateral stability characteristics of a VTOL airplane having a triangular wing mounted high on the fuselage with a triangular vertical tail on top of the wing and no horizontal tail have been made in the Langley free-flight tunnel. The static lateral stability parameters and the rolling, yawing, and sideslipping dynamic stability derivatives are presented without analysis.

Shanks, Robert E.↗
NASA NTRS1965

Deep-Stall Aerodynamic Characteristics of T-Tail Aircraft

A wind-tunnel research program has been under-taken by the NASA to study the aerodynamic characteristics of T-tail aircraft at high angles of attack. The program was designed to show the effects on longitudinal stability and control of several configuration variables. The results to date do not allow the formulation of general design rules, but the effects of several configuration variables have been noted to have a prime influence on the post-stall characteristics. An increase in tail size, changes in the location of fuselage-mounted engine nacelles, and reduced fuselage-forebody lift were all found to have a beneficial effect on static longitudinal stability at high angles of attack.

Taylor, Robert T.↗
NASA NTRS2012

Experimental Investigation of the Low-Speed Aerodynamic Characteristics of a 5.8-Percent Scale Hybrid Wing Body Configuration

A low-speed experimental investigation has been conducted on a 5.8-percent scale Hybrid Wing Body configuration in the NASA Langley 14- by 22-Foot Subsonic Tunnel. This Hybrid Wing Body (HWB) configuration was designed with specific intention to support the NASA Environmentally Responsible Aviation (ERA) Project goals of reduced noise, emissions, and fuel burn. This HWB configuration incorporates twin, podded nacelles mounted on the vehicle upper surface between twin vertical tails. Low-speed aerodynamic characteristics were assessed through the acquisition of force and moment, surface pressure, and flow visualization data. Longitudinal and lateral-directional characteristics were investigated on this multi-component model. The effects of a drooped leading edge, longitudinal flow-through nacelle location, vertical tail shape and position, elevon deflection, and rudder deflection have been studied. The basic configuration aerodynamics, as well as the effects of these configuration variations, are presented in this paper.

Gatlin, Gregory M.↗
NASA NTRS1980

Integrated application of active controls (IAAC) technology to an advanced subsonic transport project. Conventional baseline configuration study

Characteristics of the U.S. domestic fleet were evaluated to determine the mission characteristics that would have the most impact on U. S. transport fuel use in the future. This resulted in selection of a 197-passenger (plus cargo), about 3710-km (2000 nmi) mission. The existing data base was reviewed and additional analysis was conducted as necessary to complete the technical descriptions. The resulting baseline configuration utilizes a double-lobe, but nearly circular, body with seven-abreast seating. External characteristics feature an 8.71 aspect ratio, 31.5-degree sweep wing, a T-tail empennage, and a dual CF6-6D2, wing-mounted engine arrangement. It provides for 22 LD-2 or 11 LD-3 containers plus bulk cargo in the lower lobe. Passenger/cargo loading, servicing provisions, taxi/takeoff speeds, and field length characteristics are all compatible with accepted airline operations and regulatory provisions. The baseline configuration construction uses conventional aluminum structure except for advanced aluminum alloys and a limited amount of graphite epoxy secondary structure. Modern systems are used, including advanced guidance, navigation, and controls which emphasize application of digital electronics and advanced displays.

Source record↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
NASA NTRS1986

Presentation of Class 1 designs for a family of commuter airplanes

The Class 1 configuration designs of a family of commuter aircraft are presented. The proposed aircraft will have a capacity of from 25 to 100 passengers. They are to have the following common features: (1) 2 aft fuselage mounted engines; (2) a low wing; (3) a T-tail type empennage; and (4) a tricycle type landing gear. A family concept is introduced to achieve structural, systems and handling quality commonality throughout. Implementing commonality can substantially reduce manufacturing and production costs. By achieving common system designs, maintenance costs can be reduced by permitting airlines to stock a smaller inventory of spares. Therefore, the higher degree of commonality, the lower the direct operating and life cycle costs. The attempt to implement some of the commonality requirements has caused configuration design problems, i.e., the twin-body concept was introduced. Design data are compared to existing aircraft, and the extent of structural, systems and handling qualities achieved are reviewed.

Creighton, Tom↗
NASA NTRS1987

Advanced Lightplane Wing

Neico Aviation, Inc.'s tubular fuselage frame of Prescott Pusher is heliarc welded at the factory. Wings, tail, and control surfaces are of traditional aluminum. A rear mounted 180 horsepower engine with a four bladed pusher propeller allows speeds up to 200 miles per hour; an advanced rotary engine and other powerplants being tested are expected to boost cruise speed above 200 miles per hour.

Source record↗
NASA NTRS1974

Aerodynamic results of support system interference effects tests conducted in NASA/ARC 6 by 6-foot supersonic wind tunnel using an 0.015-scale model of the configuration 14OA/B SSV orbiter (OA59), volume 1

An experimental aerodynamic investigation was conducted in the NASA/ARC 6- by 6-foot supersonic wind tunnel on an 0.015-scale configuration 140A/B SSV Orbiter model. The primary objective was to determine the extent aerodynamic simulation is compromised by sting base mounting with MPS nozzles removed. Both a conventional sting (through the base) and an alternate model mounting system were utilized. The alternate mounting system consisted of a non-metric blade strut, which approximated the vertical tail and entered the model through the upper aft section of its fuselage. The model was tested both in and out of the presence of a dummy sting with and without MPS nozzles when on the alternate mounting system. Data were obtained at Mach numbers from 0.6 through 2.0, a Reynolds number of 2.5 million per foot, angles of attack from -4 through 14 degrees, angles of sideslip from -15 through 15 degrees, elevon deflections of 0 and 15 degrees, and bodyflap deflections of -11.7, 0, and 16.3 degrees.

Campbell, J. H., II↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1990

Wingtip vortex turbine investigation for vortex energy recovery

A flight test investigation has been conducted to determine the performance of wingtip vortex turbines and their effect on aircraft performance. The turbines were designed to recover part of the large energy loss (induced drag) caused by the wingtip vortex. The turbine, driven by the vortex flow, reduces the strength of the vortex, resulting in an associated induced drag reduction. A four-blade turbine was mounted on each wingtip of a single-engine, T-tail, general aviation airplane. Two sets of turbine blades were tested, one with a 15' twist (washin) and one with no twist. Th power recovered by the turbine and the installed drag increment were measured. A trade-off between turbine power and induced drag reduction was found to be a function of turbine blade incidence angle. This test has demonstrated that the wingtip vortex turbine is an attractive alternate, as well as an emergency, power source.

Abeyounis, William K.↗