Search NASA⌕ Search

SEARCH · Search NASA

Results for “TENSILE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A correlation-based approach for evaluating mechanical properties of nuclear fuel cladding tubes

The present work offers and evaluates a correlation-based approach to determine the tensile properties of nuclear fuel cladding tubes. A set of model materials with known properties (i.e., austenitic and ferritic steels, fcc- and hcp-alloys) were tested to build a correlation between conventional tensile tests and ring (hoop) and tube (axial) tests. It was shown that close-to-linear relationships exist for the basic mechanical properties (i.e., yield and ultimate stress, uniform and total elongation) between the uniaxial tensile test data and the ring and tube test data. Using the ring and tube specimen geometries, the feasibility of the approach was demonstrated via manufacturing and testing specimens from irradiated Zr and FeCrAl nuclear fuel cladding tubes. Limitations caused by specific deformation mechanisms (e.g., high ductility of 304L steel) were discussed in detail. The approach can be extended to other tubular products with different geometry and dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Electron Irradiation on Candidate Materials for Target Window in Accelerator-Driven Mo-99 Production

Room-temperature (RT) axial tensile tests were conducted in 2018 and 2021 with flat, sub-sized, dog-boned samples of non-irradiated and irradiated Inconel 718 and irradiated beryllium (Be). The sample gauge length was 7.62 mm. Tensile properties of interest are the engineering yield stress (YS), ultimate tensile stress (UTS), uniform elongation (UE) and total elongation (TE). The electron dose of the 2021 samples was ≈2 times the dose of samples tested in 2018. Relative dose rates of 0, 1 (2018), and 2 (2021) are assigned to these samples. The 2021 electron-irradiated Be samples were brittle with a low failure stress of 338±64 MPa based on two samples. The failures occurred in the gauge section. The 2018 results for electron-irradiated Be indicated a slight decrease in ductility and strength for the one electron-irradiated sample that failed in the gauge section.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Benchmarking a 9Cr-2WVTa Reduced Activation Ferritic Martensitic Steel Fabricated via Additive Manufacturing

Reduced activation ferritic (RAF) martensitic steels are promising candidates for the first wall of fusion reactors. However, current manufacturing capabilities call for these components to be made by welding wrought plates. This limits design freedom and necessitates the use of post-weld heat treatments (PWHT) in accordance with the boiler and pressure vessel code. Additive manufacturing (AM) can offer a unique solution to solve this challenge by leveraging the layer-wise deposition strategy to come up with temper bead deposition techniques to eliminate post-processing heat treatments (PPHT). However, it is necessary to benchmark the properties of RAF steels fabricated by AM with their wrought counterparts to identify the process-structure-property correlation, which is the goal of this study. The study demonstrates that while tensile properties at room temperature and high temperatures are satisfactory, the as fabricated and samples after PPHT have significant heterogeneity in tensile elongation. This has been attributed to the presence of discontinuities in the build. The as-fabricated samples have an average tensile strength of 1190 + 12 MPa and an average elongation of 15 + 5% at room temperature and 658 ± 20 MPa ultimate tensile strength (UTS) and 14 ± 7% at 600 °C. After the post-weld heat treatment, mechanical properties decrease to around 600–650 MPa and an elongation between 20–25% at room temperature to 300 MPa UTS and 25–28% elongation at 600 °C. The characterization of microstructures at various length scales demonstrates that the as-fabricated structure has a significant fraction of delta ferrite in a lath martensitic matrix. No precipitates could be identified in the as-fabricated structure. PPHT led to a decrease in the area fraction of delta ferrite and precipitation of M 23 C 6 and MX. Detailed characterization clearly demonstrates that the lack of precipitates in the as-fabricated structure could be due to the slow tempering response of the alloy. Finally, the needs to develop new alloys to achieve the objectives stated above are articulated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sizing of discontinuous natural fibers: Effect of sizing approach and sizing concentration on composite properties

Natural fiber reinforced composites (NFRCs) are gaining attention in automotive applications as an alternative to glass fiber composites due to their lightweight and renewable sourcing. However, the inherent hydrophilicity of natural fibers leads to poor compatibility with hydrophobic polymers which adversely affects the mechanical properties of the composites and can limit their application to non-structural parts. Sizing is a common approach used for synthetic fibers to improve the interface between fiber and matrix. However, there is limited study on the sizing of natural fibers, and hence the focus of this work. Here, in this study, two different approaches to sizing discontinuous coir fibers were investigated, namely; (1) ex-situ sizing and (2) in-situ sizing. A commercial polypropylene (PP) based sizing agent was used and the effects of varying sizing solution concentrations (1.5, 2.5, and 3.5 wt%) on the properties of the composites was studied. Results showed that composites prepared via the in-situ sizing process had better fiber–matrix adhesion and improved tensile properties compared to ex-situ sized composites. On studying the effect of different sizing concentrations on composite properties, we found that the tensile strength of the composites increased (by ∼ 42 %) up to 2.5 wt% sizing concentration (in solution) and then decreased. However, the impact strength decreased significantly on increasing the sizing content beyond 1.5 wt% (by ∼ 40 %). Additionally, the study was further extended to investigate the effect of sizing on different NFRCs (coir, banana, and cottonized hemp fiber) where effectiveness of sizing was found to be influenced by the fiber surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Smart manufacturing approach to manufacture bulk nanocrystalline aluminum for lightweight applications

In this research, a smart manufacturing approach was used to enhance the mechanical properties of aluminum (Al) for lightweight applications. The smart manufacturing involved cryomilling of Al powders with and without 5 wt.% magnesium (Mg) powders for varying durations followed by a high-pressure cold spray (HPCS) additive manufacturing process to prepare bulk components. The morphological changes, crystallite size, and composition of the cryomilled powders and cold sprayed (CS’ed) components were examined using scanning electron microscopy (SEM), x-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The results showed that the crystallite size reduces with an increase in cryomilling time and the addition of Mg dopant. To test the mechanical properties of the bulk CS’ed components, microhardness tests were performed using a Vickers microhardness tester. Uniaxial tensile tests were also carried out to ascertain the material’s tensile properties. The mechanical testing results showed great improvement in the hardness and tensile strength of CS’ed Al–Mg samples as compared to pure Al samples. Subsequently, fractography analysis of the tensile failed samples was carried out to determine the nature of the failure. Here, the research article also discusses the inherent mechanisms for the improvement in mechanical properties of smart manufactured components as a result of Mg doping and cryomilling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Polyamide-6 (PA6), or nylon-6, is a widely used low-cost polymer material for various applications. Manufacturing PA6 into fibers involves a spinning process such as melt extrusion, which orients the polymer chains into a semicrystalline structure. When stretching the produced fibers to high strains, the PA6 fibers transition the metastable gamma phase back into the stable gamma phase. The effects of these large stretches on mechanical properties have not been explored after the stretch has been released. In this study, the effects on mechanical properties were studied by stretching the PA6 fibers from 10% to 50% tensile strain and subsequently releasing the fibers. The stretched fibers were characterized by X-ray diffraction and atomic force microscopy to determine the changes to the crystal structure and surface roughness. The stretched fibers were then tensile tested to failure and the tensile properties were examined. The stress-strain curves on the post-stretched PA6 fibers showed clear softening in the fibers with lower initial moduli after 30% stretching. Furthermore, these results may hold a clue to softening of fibers in applications with repeated loading and have implications for mechanical stability and fatigue of this polymeric material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Linking constituent phase properties to ductility and edge stretchability of two DP 980 steels

Two DP 980 steels were characterized with multiple methods to determine its microstructure characteristics, tensile properties and edge stretchability. The first (DP980-B) is a commercial grade DP980 steel produced by AK Steel, while the second (DP980-T) is a modification of the first one by a tempering process. Both contain two individual phases: ferrite and martensite with body centered cubic (BCC) and tetragonal (BCT) crystal structure respectively. ASTM standard tensile tests were performed for both materials, revealing that DP980-B has higher work hardening and larger total elongation than DP980-T. Standard hole piercing and subsequent hole expansion and extrusion tests were also performed. The critical hole expansion ratio (HER) of hole pierced sheet at different nominal clearances, on the other hand, show an opposite trend: the HER of DP980-T almost doubles that of DP980-B. This indicates the tensile ductility and edge stretchability are determined by different mechanisms due to different deformation modes. The ductility of sheet metal during uniaxial tension is determined by deformation instability, i.e. necking, due to less constraint at the region of deformation and fracture will occur quickly after necking. The contribution of post-necking deformation to the total elongation is insignificant for the high strength grades such as DP980 steels. The ductility during hole-expansion, however, is mainly determined by material fracture behavior that is dependent on phase property disparity and material intrinsic fracture parameters. With the individual phase properties for both DP steels determined by in situ tensile tests under high energy X-ray diffraction, the results show that DP980-T steel has lower property disparities between the two phases than DP980-B steel, due to the tempering process. This explains why the DP980-T steel has higher HER than DP980-B steel: lower phase disparity will lead to less local deformation during loading. The higher work hardening rate for DP980-B steel contributes to its higher uniform elongation compared with DP980-T steel based on the maximum load condition of deformation instability. An integrated finite element simulation framework for studying hole expansion is also presented here, based on the calculated individual phase properties from the combined high energy x-ray diffraction (HEXRD) and elastic plastic self-consistent modeling. The simulation results correlate well with the experimental results on the HER difference between the two materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure and mechanical behavior of a TiC nanoprecipitate strengthened V Alloy

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiation hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.

Alloys development↗
DOE OSTI2022

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Intermediate-Term Thermal Aging Effect Evaluation for Grade 92 and 316L at The LWR Relevant Temperature

Life extension of the existing nuclear reactors imposes accumulated damages, such as higher fluences and longer period of corrosion, to structural materials, which would result in significant challenges to the traditional reactor materials such as type 304 and 316 stainless steels. Advanced alloys with superior radiation resistance will increase safety margins, design flexibility, and economics for not only the life extension of the existing fleet but also new builds with advanced reactor designs. The Electric Power Research Institute (EPRI) teamed up with Department of Energy (DOE) on the Advanced Radiation Resistant Materials (ARRM) program, aiming to develop and test degradation resistant alloys from current commercial alloy specifications by 2021 to a new advanced alloy with superior degradation resistance in light water reactor (LWR)-relevant environments by 2024. Based on a comprehensive microstructure and property screening performed in Phase-1 of the ARRM program, a total of five alloys, together with 316L and X-750 as references, were down-selected for Phase-2 neutron irradiation studies. Because thermal aging could exert a synergistic effect on neutron irradiation due to the low neutron damage rate on the order of 10 –7 displacements per atom per second (dpa/s), Grade 92 (one of the five down-selected alloys) and two heats of 316L were selected in this task to study the effect of aging at 350°C for 12.5–12.7 kh on microstructure and mechanical properties. The aging time is approximately corresponding to 5 dpa neutron irradiation, which can be served as a reference for the 5-dpa-irradiated samples of the alloys to help understand the independent neutron damage influence on microstructure and mechanical properties. Optical microscopy and scanning electron microscopy were used for microstructural characterization. Hardness, tensile, Charpy impact toughness, and fracture toughness in the ductile regime of the aged samples were examined. The aging of Grade 92 led to the formation of many Laves phase in sizes of ~100–200 nm and resulted in some reduction in hardness and yield/ultimate tensile strength with some increases in uniform and total plastic elongations, which may have helped the enhancement of Charpy impact toughness, e.g., ~4 J increase in upper-shelf energy and 20.5°C reduction in ductile-brittle transition temperature compared with the unaged condition. The fracture toughness of the aged Grade 92 showed decent toughness of ~303 MPa√m (K Jq ) with ~87 tearing modulus at 22°C, which reduced to ~241 MPa√m (~20% reduction) with ~75 tearing modulus at 300°C. The two heats of 316L are differentiated by their amounts of δ-ferrite, i.e., ~1 vol% in heat T1103 and ~4 vol% in heat N5B8. The two heats of 316L were subjected to 15% cold work (CW) as this condition is often used in nuclear reactors to help trapping radiation-induced defects and thus postpone the steady state swelling stage. The aging did not result in any noticeable microstructure changes, except for possible segregations at grain boundaries that need to be further investigated. The aging resulted in slight reduction in hardness of 316L-T1103 and slight increase in hardness of 316L-N5B8, which is consistent with their tensile testing results. The 15%CW might have introduced some inhomogeneity, resulting in large standard deviations in hardness, which were reduced after the aging. The aged 316L followed the same trend as the unaged condition for the strength and elongation results from the tensile testing. Minimum elongations appeared within ~300–600°C, above which the elongations seem to increase. Unlike the negligible or minor changes in microstructure, hardness and tensile results of the two heats of 316L, their fracture toughness showed noticeable difference. The aged 316L-T1103 showed good toughness of ~350 MPa√m with ~80 tearing modulus at 22°C, which reduced to ~271 MPa√m (~23% reduction) with ~83 tearing modulus at 300°C. In contrast, the aged 316L-N5B8 showed lower toughness of ~244 MPa√m with ~53 tearing modulus at 22°C, which reduced to ~180 MPa√m (~26% reduction) with ~31 tearing modulus at 300°C. The preliminary results indicate that the presence of high volume of δ-ferrite would noticeable impair fracture toughness although it may not influence hardness and tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

The Grain Boundary Relaxation (GBR) Approach for Manufacturing High Strength Nanocrystalline Lightweight Metals

The overarching goal of the project was to conduct research and development work as proposed in the Statement of Project Objective (SOPO) of the award document DE-FE-0009116. The project had 4 tasks and 12 milestones. All the milestone deliverables were completed. The accomplishments of the project objectives and technical discussions are described in Sections 3 and 4, respectively. The modeling and simulation work indicated that to increase the strength and stability of nanocrystalline aluminum (Al), selection of dopants, such as Mg, is necessary. It was predicted that the crystallite size should be less than 50 nm to give high strength. On the basis of modeling, cryo-milling of Al was conducted with the addition of Mg as a function of different times. The crystallite size of the cryo-milled powders was determined by XRD and TEM. Both measurements showed that the actual crystallite size of the grain was <40 nm. The thermal stability of the grain size was established as a function of temperature. It was established that the grain size was < 50 nm up to 500C. The crystallite size of the bulk sample prepared by spark plasma sintering (SPS) and cold spray (CS) additive manufacturing was less than <40 nm. The mechanical properties of the bulk samples prepared by SPS and CS, showed excellent microhardness, good tensile properties (>200 MPa) with moderate ductility and improved fatigue performance. Adding yttria stabilized zirconia (YSZ) improved the build thick of the CS sample, however the YSZ was getting embedded into the sample. A highly dense SPS samples sent for 3rd party testing to the Innovation Testing Services showed a minimum hardness of 180 HV with an average tensile strength of 512.5 MPa. The high cycle fatigue tests also showed an endurance limit of 179.5 MPa. The Energy cost evaluations showed an overall energy cost of around $\$$17.05 for the cryomilling and SPS processes and the total manufacturing cost calculations of $\$$78.14 for 1 kg of sample. The energy cost to prepare a Kg of CS sample is $\$$17.60 and the overall manufacturing cost is $\$$86.85.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High entropy alloys: A focused review of mechanical properties and deformation mechanisms

The high-entropy alloy (HEA) concept was based on the idea that high mixing entropy can promote formation of stable single-phase microstructures. During the past 15 years, various alloy systems have been explored to identify HEA systems with improved property combinations, leading to an extraordinary growth of this field. In the large pool of alloys with varying characteristics, the first single-phase HEA with good tensile properties, the equiatomic CrMnFeCoNi alloy has become the benchmark material, and it forms the basis of much of our current fundamental understanding of HEA mechanical behavior. As the field is evolving to the more broadly defined complex concentrated alloys (CCAs) and the available data in the literature increase exponentially, a fundamental question remains unchanged: how special are these new materials? In the first part of this review, select mechanical properties of HEAs and CCAs are compared with those of conventional engineering alloys. This task is difficult because of the limited tensile data available for HEAs and CCAs. Additionally, the wider suite of mechanical properties needed to assess structural materials is woefully lacking. Nonetheless, our evaluations have not revealed many HEAs or CCAs with properties far exceeding those of conventional engineering alloys, although specific alloys can show notable enhancements in specific properties. Consequently, it is reasonable to first approach the understanding of HEAs and CCAs through the assessment of how the well-established deformation mechanisms in conventional alloys operate or are modified in the presence of the high local complexity of the HEAs and CCAs. The second part of the paper provides a detailed review of the deformation mechanisms of HEAs with the FCC and BCC structures. For the former, we chose the CrMnFeCoNi (Cantor) alloy because it is the alloy on which the most rigorous and thorough investigations have been performed and, for the latter, we chose the TiZrHfNbTa (Senkov) alloy because this is one of the few refractory HEAs that exhibits any tensile ductility at room temperature. As expected, our review shows that the fundamental deformation mechanisms in these systems, and their dependence on basic physical properties, are broadly similar to those of conventional FCC and BCC metals. The third part of this review examines the theoretical and modeling efforts to date that seek to provide either qualitative or quantitative understanding of the mechanical performance of FCC and BCC HEAs. Since experiments reveal no fundamentally new mechanisms of deformation, this section starts with an overview of modeling perspectives and fundamental considerations. Next, the review turns to the evolution of modeling and predictions as compared to recent experiments, highlighting both successes and limitations. Finally, in spite of some significant successes, important directions for further theory development are discussed. Overall, while the individual deformation mechanisms or properties of the HEAs and CCAs are not, by and large, “special” relative to conventional alloys, the present HEA rush remains valuable because the compositional freedom that comes from the multi-element space will allow exploration of whether multiple mechanisms can operate sequentially or simultaneously, which may yet lead to the creation of new alloys with a spectrum of mechanical properties that are significantly superior to those of current engineering alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electroslag additive manufacturing: A pathway for high throughput near net shape production

Electroslag Additive Manufacturing (ESAM), a new high-throughput additive manufacturing (AM) method that combines Electroslag Strip Cladding (ESC) and wire arc AM (WAAM) is introduced. This combination enables the high deposition rate of ESC (more than 20 kg/h with a 60 mm strip electrode) to benefit from the precise geometric control of WAAM. As a precursor to ESAM, the ESC process is investigated in an AM context independently by evaluating both direct and staggered bead-stacking strategies and analyzing the microstructural and mechanical properties of each. This is followed by an ESAM demonstration producing an annular geometry by pairing ESC with gas tungsten arc welding (GTAW), wherein GTAW is utilized to construct annular walls that are subsequently infilled via ESC. The microstructure and mechanical properties of ESC-only AM are compared with that of the ESAM method and it is shown that printed integral retaining walls do not impact the resulting mechanical properties of ESAM. Furthermore, results indicate that ESAM-produced Alloy 625 parts exhibit tensile properties on par with cast counterparts, supporting the method’s scalability to components exceeding one metric ton, and possibly making ESAM a viable future manufacturing approach for competitive production of large-scale components currently manufactured by casting and forging.

Additive manufacturing↗
DOE OSTI2024

Critical mineral substitutions in IN617: A combined computational and experimental approach to performance evaluation and feasibility

Addressing the escalating demand for critical minerals (CMs) driven by global climate change initiatives, this study explores compositional modifications to Inconel 617 (IN617) by substituting cobalt (Co) with manganese (Mn) across various atomic percentages. Here, we conducted a computational feasibility study employing Molecular Dynamics (MD) simulations to provide strategic guidance for experimental validation. The simulations analyzed tensile strength and corrosion resistance for five modified compositions (M1 to M5) to identify optimal properties. Tensile tests on cubic simulation cells were performed to generate stress-strain curves, revealing the impact of Co replacement with Mn on tensile strength—a metric correlated with hardness. Oxygen penetration simulations were conducted to evaluate corrosion resistance, indicating that reduced oxygen penetration depth corresponds to enhanced resistance. Promising compositions underwent phase diagram calculations for assessing phase stability. The optimal composition (M1), characterized by high tensile strength and minimal oxygen penetration, was chosen for experimental validation using induction melting and friction stir consolidation techniques. The materials were further characterized using SEM-EDS, XRD, and Vickers hardness testing. Our findings suggest that Mn substitution in IN617 can yield mechanical performance at par with high-Co alloys in energy-critical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical Property Measurements of HFIR-irradiated FM and ODS Alloys

This report provides a summary of the post-irradiation examination of the tensile properties of three ODS ferritic alloys, 14YWT-SM13, 9YWTV-PM2 and OFRAC, and two HT9 ferritic/martensitic steels, one with low N content and the other with high N content. The neutron irradiations were conducted in the flux trap of the High Flux Isotope Reactor as part of the Additive Manufacturing, Oxide Dispersion Strengthened Alloys and Wrought Steels (AMOW) irradiation campaign. Sub-sized tensile specimens fabricated from each material were exposed to nominal target temperatures and neutron doses of 300°C, 385°C, and 525°C and 8 dpa, 16 dpa, and 50 dpa, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Recyclable Cellulose Fiber Reinforced Vitrimer Composite

Vitrimer is an innovative class of polymeric materials which demonstrates traditional thermoset-like mechanical and chemical resilience while still being able to flow on demand like a traditional thermoplastic through covalently adaptive dynamic linkages. Herein, high-performance cellulose fiber reinforced vitrimer composites are developed using an epoxy-based vitrimer and natural cellulose paper. The reinforced vitrimer composite was fabricated by impregnating the porous structure of cellulose paper with two curable monomers, followed by in-situ polymerization of the monomers inside the fibrous scaffold. The introduction of hydroxyl group present on the cellulosic framework assisted in a faster topological rearrangement of the crosslinked matrix through transesterification exchange reaction, thus imparting various sought-after properties like shape recovery and recyclability via simple thermal reprocessing. Moreover, the reinforced vitrimer composite exhibits superior tensile properties as high as 90 MPa with 15-25 volume% vitrimer loading due to the interfacial adhesion via ester exchange reaction between the epoxy matrix and functionalities on the cellulosic fibers. Noteworthily, the key ingredients of the resulting composite (i.e., epoxy-based vitrimer and cellulose fibers) can be comfortably recycled without using aggressive chemical treatment, enabling composite to be easily recycled or disposed of at the end of service life and assist in reducing the subsequent manufacturing cost. This study would shed light on the development of a recyclable polymer composite with exceptional mechanical properties while simultaneously demonstrating self-healing and shape memory capabilities.

Rohewal, Sargun Singh↗
DOE OSTI2023

Investigation of pressure-controlled injection molding on the mechanical properties and embodied energy of recycled high-density polyethylene

Manufacturing with secondary feedstock has been identified as an effective strategy to improve plastic circularity. However, product quality inconsistencies arise due to variations in molecular weight, rheology, and mechanical properties. This work evaluates the processing of recycled high-density polyethylene using pressure-controlled injection molding with a focus on processing behavior and energy consumption. Further, the effects of injection velocity, packing pressure, and transfer position are benchmarked against a conventional velocity-controlled process. The experimental results show that the novel process control strategy significantly affects the mechanical properties, in-mold rheology, and energy consumption. Parts fabricated using pressure-controlled injection molding showed higher tensile properties due to increased macromolecular orientation. Additionally, reduced energy was used due to lower melt pressures required to completely replicate the cavity geometry. The results demonstrate the potential of the technology to support increased utilization of secondary feedstock and reduced carbon footprint.

36 MATERIALS SCIENCE↗