Results for “TRAJECTORY MEASURING SYSTEM” — Page 6

NASA NTRS1985

Multiple Scattering Effects in de/dx-E Instruments for Isotopic Composition Studies

The development of cosmic ray telescopes to separate individual isotopes of heavy elements using the dE/dx-vs.-E technique depends on the incorporation of precise trajectory sensing elements into these systems. In typical implementations the particle trajectory is derived from a set of position measurements made prior to a particle's entering the first energy loss detector. The use of the trajectory obtained in this way to correct energy loss signals for the actual pathlengths through the detectors depends on the assumption that the particle trajectory is a straight line. In order to resolve iron isotopes the angles of incidence, theta the particle track must be known rather accurately.

Wiedenbeck, M. E.↗

NASA NTRS1987

The dust distribution within the inner coma of comet P/Halley 1982i - Encounter by Giotto's impact detectors

Analyses are presented of Giotto's Dust Impact Detection System experiment measurements of dust grains incident on the Giotto dust shield along its trajectory through the coma of comet P/Halley on March 13 and 14, 1986. Ground-based CCD imagery of the inner coma dust continuum at the time of the encounter are used to derive the area of grains intercepted by Giotto. Data obtained at large masses show clear evidence of a decrease in the mass distribution index at these masses within the coma; it is shown that such a value of the mass index can furnish sufficient mass for consistency with an observed deceleration.

Mcdonnell, J. A. M.↗

NASA NTRS1994

Small Business Innovations

A Small Business Innovation Research (SBIR) contract resulted in a series of commercially available lasers, which have application in fiber optic communications, difference frequency generation, fiber optic sensing and general laboratory use. Developed under a Small Business Innovation Research (SBIR) contract, the Phase Doppler Particles Analyzer is a non-disruptive, highly accurate laser-based method of determining particle size, number density, trajectory, turbulence and other information about particles passing through a measurement probe volume. The system consists of an optical transmitter and receiver, signal processor and computer with data acquisition and analysis software. A variety of systems are offered for applications including spray characterization for paint, and agricultural and other sprays. The Microsizer, a related product, is used in medical equipment manufacturing and analysis of contained flows. High frequency components and subsystems produced by Millitech Corporation are marketed for both research and commercial use. These systems, which operate in the upper portion of the millimeter wave, resulted from a number of Small Business Innovation Research (SBIR) projects. By developing very high performance mixers and multipliers, the company has advanced the state of the art in sensitive receiver technology. Components are used in receivers and transceivers for monitoring chlorine monoxides, ozone, in plasma characterization and in material properties characterization.

Source record↗

NASA NTRS2007

TDRSS Augmentation for Launch and Ascent High Speed Navigation Filter

An investigation was performed to evaluate the feasibility and possible advantages of augmenting the High Speed Trajectory Determination (HSTD) ground navigation filter with measurements from the Tracking & Data Relay Satellite System (TDRSS) constellation. The proposed communications system strategy for Constellation uses TDRSS rather than ground S-band, so the capability of replacing the S-band navigation capability with TDRSS was considered. HSTD simulations were performed with combinations of S-band, C-band, and TDRSS measurements. Several assumptions are made with regard to measurement biases and signal noise characteristics to produce first-look level accuracies. Preliminary results show that solutions using TDRSS instead of S-band have similar or improved performance from the view of filter covariance and may be a feasible alternative. These results also show that TDRSS tracking alone gives poorer observations and resulting performance Operational and other constraints to the use of TDRSS in a high-speed ground navigation filter are not addressed.

Holt, Greg .↗

NASA NTRS1993

Flight validation of a pulsed smoke flow visualization system

A flow visualization scheme, designed to measure vortex fluid dynamics on research aircraft, was validated in flight. Strake vortex trajectories and axial core velocities were determined using pulsed smoke, high-speed video images, and semiautomated image edge detection hardware and software. Smoke was pulsed by using a fast-acting three-way valve. After being redesigned because of repeatedly jamming in flight, the valve shuttle operated flawlessly during the last two tests. A 25-percent scale, Gothic strake was used to generate vortex over the wing of a GA-7 Cougar and was operated at a local angle of attack of 22 degrees and Reynolds number of approximately 7.8 x 10(exp 5)/ft. Maximum axial velocities measured in the vortex core were between 1.75 and 1.95 times the freestream velocity. Analysis of the pulsed smoke system's affect on forebody vortices indicates that the system may reorient the forebody vortex system; however, blowing momentum coefficients normally used will have no appreciable affect on the leading-edge extension vortex system. It is recommended that a similar pulsed smoke system be installed on the F/A-18 High Angle Research Vehicle and that this approach be used to analyze vortex core dynamics during the remainder of its high-angle-of-attack research flights.

Ward, Donald T.↗

NASA NTRSDate not supplied

Lunar Relay Onboard Navigation Performance and Effects on Lander Descent to Surface

A system of Lunar relay satellites has been proposed to address communication and navigation needs and ensure robustness for the variety of upcoming robotic and human exploration missions to the Moon. The relays are envisioned to estimate self position and time knowledge onboard, allowing the system to provide in-situ navigation services to missions in the Lunar and cis-Lunar environment. The quality and accuracy of those services are highly dependent on the navigation performance of the relay itself. To assess the Lunar relay navigation performance, a series of orbit determination (OD) Monte Carlo (MC) simulations are run using Lunar gravity modeling up to a degree and order of 250 and a variety of onboard clocks and measurement types including weak-signal GNSS, Ground Network (GN) pseudorange (PR) and Doppler, and optical navigation (OpNav) center-finding (CF). The estimated trajectories produced by these Lunar relay MC simulations, along with the associated errors, and transmitted navigation reference signal parameters, are used to evaluate the expected navigation performance of a user on a descent trajectory to the Lunar surface. The scenario features a lander system performing onboard navigation relying on one-way range and Doppler measurements from reference signals emitted by the Lunar relay. This paper can be used as a reference in determining the onboard clock and measurement types necessary to obtain acceptable navigation performance for the Lunar relay, and as a baseline for Lunar lander navigation performance using accurate measurements from a relay reference signal.

Jeffrey L. Small↗

NASA NTRSDate not supplied

Lunar Relay Onboard Navigation Performance and Effects on Lander Descent to Surface

A system of Lunar relay satellites has been proposed to address communication and navigation needs and ensure robustness for the variety of upcoming robotic and human exploration missions to the Moon. The relays are envisioned to estimate self-position and time knowledge onboard, allowing the system to provide in-situ navigation services to missions in the Lunar and cis-Lunar environment. The quality and accuracy of those services are highly dependent on the navigation performance of the relay itself. To assess the Lunar relay navigation performance, a series of orbit determination (OD) Monte Carlo (MC) simulations are run using Lunar gravity modeling up to a degree and order of 250 and a variety of onboard clocks and measurement types including weak-signal GNSS, Ground Network (GN) pseudorange (PR) and Doppler, and optical navigation (OpNav) center-finding (CF). The estimated trajectories produced by these Lunar relay MC simulations, along with the associated errors, and transmitted navigation reference signal parameters, are used to evaluate the expected navigation performance of a user on a descent trajectory to the Lunar surface. The scenario features a lander system performing onboard navigation relying on one-way range and Doppler measurements from reference signals emitted by the Lunar relay. This paper can be used as a reference in determining the onboard clock and measurement types necessary to obtain acceptable navigation performance for the Lunar relay, and as a baseline for Lunar lander navigation performance using accurate measurements from a relay reference signal.

Jeffrey L. Small↗

NASA NTRS2009

Lunar Landing Trajectory Design for Onboard Hazard Detection and Avoidance

The Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project is developing the software and hardware technology needed to support a safe and precise landing for the next generation of lunar missions. ALHAT provides this capability through terrain-relative navigation measurements to enhance global-scale precision, an onboard hazard detection system to select safe landing locations, and an Autonomous Guidance, Navigation, and Control (AGNC) capability to process these measurements and safely direct the vehicle to a landing location. This paper focuses on the key trajectory design issues relevant to providing an onboard Hazard Detection and Avoidance (HDA) capability for the lander. Hazard detection can be accomplished by the crew visually scanning the terrain through a window, a sensor system imaging the terrain, or some combination of both. For ALHAT, this hazard detection activity is provided by a sensor system, which either augments the crew s perception or entirely replaces the crew in the case of a robotic landing. Detecting hazards influences the trajectory design by requiring the proper perspective, range to the landing site, and sufficient time to view the terrain. Following this, the trajectory design must provide additional time to process this information and make a decision about where to safely land. During the final part of the HDA process, the trajectory design must provide sufficient margin to enable a hazard avoidance maneuver. In order to demonstrate the effects of these constraints on the landing trajectory, a tradespace of trajectory designs was created for the initial ALHAT Design Analysis Cycle (ALDAC-1) and each case evaluated with these HDA constraints active. The ALHAT analysis process, described in this paper, narrows down this tradespace and subsequently better defines the trajectory design needed to support onboard HDA. Future ALDACs will enhance this trajectory design by balancing these issues and others in an overall system design process.

Paschall, Steve↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D. Karlgaard↗

NASA NTRS1993

Observability during planetary approach navigation

The objective of the research is to develop an analytic technique to predict the relative navigation capability of different Earth-based radio navigation measurements. In particular, the problem is to determine the relative ability of geocentric range and Doppler measurements to detect the effects of the target planet gravitational attraction on the spacecraft during the planetary approach and near-encounter mission phases. A complete solution to the two-dimensional problem has been developed. Relatively simple analytic formulas are obtained for range and Doppler measurements which describe the observability content of the measurement data along the approach trajectories. An observability measure is defined which is based on the observability matrix for nonlinear systems. The results show good agreement between the analytic observability analysis and the computational batch processing method.

Bishop, Robert H.↗

NASA NTRS2008

Storm Surge Measurement with an Airborne Scanning Radar Altimeter

Over the years, hurricane track and intensity forecasts and storm surge models and the digital terrain and bathymetry data they depend on have improved significantly. Strides have also been made in knowledge of the detailed variation of the surface wind field driving the surge. The area of least improvement has been in obtaining data on the details of the temporal/spatial variation of the storm surge dome of water as it evolves and inundates the land to evaluate the performance of the numerical models. Tide gages in the vicinity of the landfall are frequently destroyed by the surge. Survey crews dispatched after the event provide no temporal information and only indirect indications of the maximum surge envelope over land. The landfall of Hurricane Bonnie on 26 August 1998, with a surge less than 2 m, provided an excellent opportunity to demonstrate the potential benefits of direct airborne measurement of the temporal/spatial evolution of storm surge. Despite a 160 m variation in aircraft altitude, an 11.5 m variation in the elevation of the mean sea surface relative to the ellipsoid over the flight track, and the tidal variation over the 5 hour data acquisition interval, a survey-quality Global Positioning System (GPS) aircraft trajectory allowed the NASA Scanning Radar Altimeter carried by a NOAA hurricane research aircraft to produce storm surge measurements that generally fell between the predictions of the NOAA SLOSH model and the North Carolina State University storm surge model.

Wright, C. W.↗

NASA NTRS1999

Feasibility of Decentralized Linear-Quadratic-Gaussian Control of Autonomous Distributed Spacecraft

A distributed satellite formation, modeled as an arbitrary number of fully connected nodes in a network, could be controlled using a decentralized controller framework that distributes operations in parallel over the network. For such problems, a solution that minimizes data transmission requirements, in the context of linear-quadratic-Gaussian (LQG) control theory, was given by Speyer. This approach is advantageous because it is non-hierarchical, detected failures gracefully degrade system performance, fewer local computations are required than for a centralized controller, and it is optimal with respect to the standard LQG cost function. Disadvantages of the approach are the need for a fully connected communications network, the total operations performed over all the nodes are greater than for a centralized controller, and the approach is formulated for linear time-invariant systems. To investigate the feasibility of the decentralized approach to satellite formation flying, a simple centralized LQG design for a spacecraft orbit control problem is adapted to the decentralized framework. The simple design uses a fixed reference trajectory (an equatorial, Keplerian, circular orbit), and by appropriate choice of coordinates and measurements is formulated as a linear time-invariant system.

Carpenter, J. Russell↗

NASA NTRS1999

Feasibility of Decentralized Linear-Quadratic-Gaussian Control of Autonomous Distributed Spacecraft

A distributed satellite formation, modeled as an arbitrary number of fully connected nodes in a network, could be controlled using a decentralized controller framework that distributes operations in parallel over the network. For such problems, a solution that minimizes data transmission requirements, in the context of linear-quadratic-Gaussian (LQG) control theory, was given by Speyer. This approach is advantageous because it is non-hierarchical, detected failures gracefully degrade system performance, fewer local computations are required than for a centralized controller, and it is optimal with respect to the standard LQG cost function. Disadvantages of the approach are the need for a fully connected communications network, the total operations performed over all the nodes are greater than for a centralized controller, and the approach is formulated for linear time-invariant systems. To investigate the feasibility of the decentralized approach to satellite formation flying, a simple centralized LQG design for a spacecraft orbit control problem is adapted to the decentralized framework. The simple design uses a fixed reference trajectory (an equatorial, Keplerian, circular orbit), and by appropriate choice of coordinates and measurements is formulated as a linear time-invariant system.

Carpenter, J. Russell↗

NASA NTRS1973

3-D multilateration for measurement of earth crustal deformation and network densification

Discussion of how range and range-difference data types can make possible precise three-dimensional measurement of ground station positions and the position of an artificial signal source, without explicit dependence upon the signal source trajectory. An effective strategy for such measurement is to combine the multilateration approach with a VLBI system using natural radio sources. The VLBI methods would provide a coarse grid of three-dimensional benchmark locations on a regional and global scale. Multilateration stations would then occupy these coarse grid locations and provide a means for highly portable, relatively low-cost units to then densify networks on a regional and local scale. Because a multilateration approach can make use of strong artificial radio sources, it makes possible the use of relatively low-cost, highly mobile stations. Such mobile stations are virtually essential for three dimensional surveying in heavily urbanized areas or in rugged terrain.

Ong, K. M.↗

NASA NTRS1959

Trajectory Control for Vehicles Entering the Earth's Atmosphere at Small Flight Path Angles

Methods of controlling the trajectories of high-drag-low-lift vehicles entering the earth's atmosphere at angles of attack near 90 deg and at initial entry angles up to 3 deg are studied. The trajectories are calculated for vehicles whose angle of attack can be held constant at some specified value or can be perfectly controlled as a function of some measured quantity along the trajectory. The results might be applied in the design of automatic control systems or in the design of instruments which will give the human pilot sufficient information to control his trajectory properly during an atmospheric entry. Trajectory data are compared on the basis of the deceleration, range, angle of attack, and, in some cases, the rate of descent. The aerodynamic heat-transfer rate and skin temperature of a vehicle with a simple heat-sink type of structure are calculated for trajectories made with several types of control functions. For the range of entry angles considered, it is found that the angle of attack can be controlled to restrict the deceleration down to an arbitrarily chosen level of 3g. All the control functions tried are successful in reducing the maximum deceleration to the desired level. However, in order to avoid a tendency for the deceleration to reach an initial peak decrease, and then reach a second peak, some anticipation is required in the control function so that the change in angle of attack will lead the change in deceleration. When the angle of attack is controlled in the aforementioned manner, the maximum rate of aerodynamic heat transfer to the skin is reduced, the maximum skin temperature of the vehicle is virtually unaffected, and the total heat absorbed is slightly increased. The increase in total heat can be minimized, however, by maintaining the maximum desired deceleration for as much of the trajectory as possible. From an initial angle of attack of 90 deg, the angle-of-attack requirements necessary to maintain constant values of deceleration (1g to 4g) and constant values of rate of descent (450 to 1,130 ft/sec) as long as it is aerodynamically practical are calculated and are found to be moderate in both magnitude and rate. Entry trajectories made with these types of control are presented and discussed.

Eggleston, John M.↗

NASA NTRS1982

Modeling methodology for MLS range navigation system errors using flight test data

Flight test data was used to develop a methodology for modeling MLS range navigation system errors. The data used corresponded to the constant velocity and glideslope approach segment of a helicopter landing trajectory. The MLS range measurement was assumed to consist of low frequency and random high frequency components. The random high frequency component was extracted from the MLS range measurements. This was done by appropriate filtering of the range residual generated from a linearization of the range profile for the final approach segment. This range navigation system error was then modeled as an autoregressive moving average (ARMA) process. Maximum likelihood techniques were used to identify the parameters of the ARMA process.

Karmali, M. S.↗

NASA NTRS2014

Trajectory Prediction Accuracy and Error Sources for Regional Jet Descents: Results of a 2010 Flight Trial at Denver International Airport using a Global 5000 Test Aircraft - Part I

The Efficient Descent Advisor (EDA) controller automation tool generates trajectory-based speed, path, and altitude-profile advisories to facilitate efficient, continuous descents into congested terminal airspace. While prior field trials have assessed the trajectory-prediction accuracy for large jet (i.e., Boeing and Airbus) types, smaller (i.e., regional and business) jet types present unique challenges involving different descent procedures and Flight Management System (FMS) capabilities. A small-jet field trial was conducted at Denver in the fall of 2010 with the objective of measuring trajectory prediction accuracy and quantifying the primary sources of error. This paper uses data collected onboard a Bombardier Global 5000 test aircraft to quantify the size and sources of trajectory prediction error. Error sources were quantified for the 44 runs by incrementally replacing predicted data with data collected onboard the aircraft and measuring the effect on time error. Results for en-route descents, from prior to top of descent to the meter fix 60-120 nmi downstream, indicate that the aircraft arrived an average 15 seconds earlier than predicted, with a standard deviation of 10 seconds. Target Mach and CAS deceleration were found to be the two largest error sources. If CAS deceleration error was reduced using a typical, more predictable level flight deceleration then the arrival time prediction error in 2010 would be on par with a 2009 flight trial of Airbus and Boeing revenue flights. Four of the error sources, tracker jumps, CAS deceleration, target Mach, and path distance, lend themselves to significant reductions with modest to no changes to ATC automation andor procedures. Wind error and its impact on arrival time error was significantly reduced in 2010 compared to a 1994 flight test using NASAs Boeing 737 test aircraft.

Trajectory Prediction Error↗