Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tail”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Thrust reversing effects on horizontal tail effectiveness of twin-engine fighter aircraft

The Langley Research Center has conducted an experimental program to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach (Mach number 0.15) and in-flight (Mach number 0.60 and 0.90) speeds. Twin vertical tails were tested at three longitudinal locations. Two nonaxisymmetric nozzle reverser concepts were studied. The effects of thrust reversing on horizontal tail effectiveness were found to be very dependent upon vertical tail locations. At approach speeds thrust reverser operation usually resulted in large variations in horizontal tail effectiveness as either nozzle pressure ratio or model angle of attack was varied. Either increases or decreases in tail effectiveness ocurred due to reverse operation depending upon tail location. At in-flight conditions there were always decreases in tail effectiveness due to reverser operation regardless of vertical tail location.

Capone, F. J.↗
NASA NTRS1985

Wind-tunnel investigation at supersonic speeds of a remote-controlled canard missile with a free-rolling-tail brake torque system

Wind tunnel tests were conducted at Mach numbers 1.70, 2.16, and 2.86 to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed or free rolling tailfin afterbodies. Mechanical coupling effects of the free-rolling-tail afterbody were investigated by using an electronic electromagnetic brake system providing arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail roll rate. Remote-controlled canards were deflected to provide pitch, yaw, and roll control. Results indicate that the induced rolling moment coefficients due to canard yaw control are reduced and linearized for the free-rolling-tail (free-tail) configuration. The canards of the latter provide conventional roll control for the entire angle-of-attack test range. For the free-tail configuration, the induced rolling moment coefficient due to canard yaw control increased and the canard roll control decreased with increases in brake torque, which simulated bearing friction torque. It appears that a compromise in regard to bearing friction, for example, low-cost bearings with some friction, may allow satisfactory free-tail aerodynamic characteristics that include reductions in adverse rolling-moment coefficients and lower tail roll rates.

Blair, A. B., Jr.↗
NASA NTRS1996

Computation and Validation of Fluid/Structure Twin Tail Buffet Response

The buffet response of the flexible twin-tail/delta wing configuration, a multidisciplinary problem, is solved using three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations which are used for obtaining the flow-field vector and the aerodynamic loads on the twin tails. The second set is the coupled aeroelastic equations which are used for obtaining the bending and torsional deflections of the twin tails. The third set is the grid-displacement equations which are used for updating the grid coordinates due to the tail deflections. The computational model is similar to the one used by Washburn et. al. which consists of a delta wing of aspect ratio one and twin tails with taper ratios of 0.23. The vortex of the twin tails are located at the wing trailing edge. The configuration is pitched at 30 deg angle of attack, and the freestream Mach number and Reynolds number are 0.3 and 1.25 million, respectively. With the twin tails fixed as rigid surfaces, the problem is solved for the initial flow conditions. Next, the problem is solved for the twin tail response for uncoupled bending and torsional vibrations due to the unsteady loads produced by the vortex breakdown flow of the leading-edge vortex cores. The configuration is investigated for three spanwise positions of the twin tails; inboard, midspan and outboard locations. The computational results are validated and are in very good agreement with the experimental data of Washburn, et. al.

Massey, Steven J.↗
NASA NTRS1961

Static Longitudinal Characteristics at High Subsonic Speeds of a Complete Airplane Model with a Highly Tapered Wing having the 0.80 Chord Line Unswept and with Several Tail Configurations

An investigation was made at high subsonic speeds of a complete model having a highly tapered wing and several tail configurations. The basic aspect-ratio-4.00 wing had zero taper and an unswept 0.80 chord line. Several aspect-ratio modifications to the basic wing were made by clipping off portions of the wing tips. The complete model was tested with a chord-plane tail, a T-tail, and a biplane tail (combined T-tail and chord-plane tail). The model was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92. The data show that, when reduced to the same static margin, all the tail configurations tested on the model provided fairly good stability characteristics, the biplane tail giving the.best overall characteristics as regards pitching-moment linearity. Changes in static margin at zero lift coefficient with Mach number were small for the model with these tails over the Mach number range investigated.

Goodson, Kenneth W.↗
NASA NTRS1977

The ionospheres and plasma tails of comets

The paper reviews the current state of knowledge about cometary plasma (type I) tails and ionospheres. Observational statistics for type I tails are examined along with spectroscopic observations of plasma tails, identified ion species in such tails, and the morphology of cometary plasma tails and ionospheres. Evidence for a strong interaction between comets and the solar wind is evaluated on the basis of observations of plasma-tail orientations, large accelerations of tail structures, and correlations between disturbances in type I tails and solar-wind or geomagnetic disturbances. The use of comets as solar-wind probes is discussed, the nature of comet-solar-wind interactions is investigated, and ionization sources for cometary gases are considered. Hydrodynamic models of comet-solar-wind interaction are summarized, and the structure and ion chemistry of cometary ionospheres are studied. Observations suggesting that significant magnetic fields are associated with comets are briefly reviewed and interpreted.

Mendis, D. A.↗
NASA NTRS1978

On the average configuration of the geomagnetic tail

Over 3000 hours of IMP-6 magnetic field data obtained between 20 and 33 R sub E in the geomagnetic tail have been used in a statistical study of the tail configuration. A distribution of 2.5 minute averages of B sub Z as a function of position across the tail reveals that more flux crosses the equatorial plane near the dawn and dusk flanks than near midnight. The tail field projected in the solar magnetospheric equatorial plane deviates from the X axis due to flaring and solar wind aberration by an angle alpha = -0.9 y sub SM - 1.7 where Y sub SM is in earth radii and alpha is in degrees. After removing these effects the Y component of the tail field is found to depend on interplanetary sector structure. During an away sector the B sub Y component of the tail field is on average 0.5 gamma greater than that during a toward sector, a result that is true in both tail lobes and is independent of location across the tail.

Fairfield, D. H.↗
NASA NTRS1988

Development in helicopter tail boom strake applications in the US

The use of a strake or spoiler on a helicopter tail boom to beneficially change helicopter tail boom air loads was suggested in the United States in 1975. The anticipated benefits were a change of tail boom loads to reduce required tail rotor thrust and power and improve directional control. High tail boom air loads experienced by the YAH-64 and described in 1978 led to a wind tunnel investigation of the usefullness of strakes in altering such loads on the AH-64, UH-60, and UH-1 helicopters. The wind tunnel tests of 2-D cross sections of the tail boom of each demonstrated that a strake or strakes would be effective. Several limited test programs with the U.S. Army's OH-58A, AH-64, and UH-60A were conducted which showed the effects of strakes were modest for those helicopters. The most recent flight test program, with a Bell 204B, disclosed that for the 204B the tail boom strake or strakes would provide more than a modest improvement in directional control and reduction in tail rotor power.

Wilson, John C.↗
NASA NTRS1955

Flight Measurements of Horizontal-Tail Loads on the Bell X-5 Research Airplane at a Sweep Angle of 58.7 Deg

A flight investigation was made at altitudes of 40,000, 25,000 and 15,000 feet to determine the horizontal-tail loads of the Bell X-5 research airplane at a sweep angle of 58.7 deg over the lift range of the airplane for Mach numbers from 0.61 to 1.00. The horizontal-tail loads were found to be nonlinear with lift throughout the lift ranges tested at all Mach numbers except at a Mach number of 1.00. The balancing tail loads reflected the changes which occur in the wing characteristics with increasing angle of attack. The nonlinearities were, in general, more pronounced at the higher angles of attack near the pitch-up where the balancing tail loads indicate that the wing-fuselage combination becomes unstable. No apparent effects of altitude on the balancing tail loads were evident over the comparable lift ranges of these tests at altitudes from 40,000 feet to 15,000 feet. Comparisons of balancing tail loads obtained from flight and windtunnel tests indicated discrepancies in absolute magnitudes, but the general trends of the data agree. Some differences in absolute magnitude may be accounted for by the tail load carried inboard of the strain-gage station and the load induced on the fuselage by the presence of the tail. These loads were not measured in flight.

Reed, Robert D↗
NASA NTRS1948

Hydrodynamic Characteristics of a Low-drag, Planing-tail Flying-boat Hull

The hydrodynamic characteristics of a flying-boat incorporating a low-drag, planing-tail hull were determined from model tests made in Langley tank number 2 and compared with tests of the same flying boat incorporating a conventional-type hull. The planing-tail model, with which stable take-offs were possible for a large range of elevator positions at all center-of-gravity locations tested, had more take-off stability than the conventional model. No upper-limit porpoising was encountered by the planing-tail model. The maximum changes in rise during landings were lower for the planing-tail model than for the conventional model at most contact trims, an indication of improved landing stability for the planing-tail model. The hydrodynamic resistance of the planing-tail hull was lower than the conventional hull at all speeds, and the load-resistance ratio was higher for the planing-tail hull, being especially high at the hump. The static trim of the planing-tail hull was much higher than the conventional hull, but the variation of trim with speed during take-off was smaller.

Suydam, Henry B↗
NASA NTRS1948

Altitude-wind-tunnel investigation of tail-pipe burning with a Westinghouse X24C-4B axial-flow turbojet engine

Thrust augmentation of an axial-flow type turbojet engine by burning fuel in the tail pipe has been investigated in the NACA Cleveland altitude wind tunnel. The performance was determined over a range of simulated flight conditions and tail-pipe fuel flows. The engine tail pipe was modified for the investigation to reduce the gas velocity at the inlet of the tail-pipe combustion chamber and to provide an adequate seat for the flame; four such modifications were investigated. The highest net-thrust increase obtained in the investigation was 86 percent with a net thrust specific fuel consumption of 2.91 and a total fuel-air ratio of 0.0523. The highest combustion efficiencies obtained with the four configurations ranged from 0.71 to 0.96. With three of the tail-pipe burners, for which no external cooling was provided, the exhaust nozzle and the rear part of the burner section were bright red during operation at high tail-pipe fuel-air ratios. With the tail-pipe burner for which fuel and water cooling were provided, the outer shell of the tail-pipe burner showed no evidence of elevated temperatures at any operating condition.

Fleming, William A↗
NASA NTRS1994

Comparison of the plasma tails of four comets: P/Halley, Okazaki-Levy-Rudenko, Austin, and Levy

Photographic and charge coupled device (CCD) plasma tail observations are compared for four comets: P/Halley (22 nights in 1985/1986), Okazaki-Levy-Rudenko 1989 XIX (1989 December 2), Austin 1990 V (nine nights in 1990), and Levy 1990 XX (two nights in 1991). We present a discussion of several image-processing techniques used to enhance the visibility of the plasma tail features in order to measure velocities, accelerations, and position angles. The data are used to assess the validity of various physical mechanisms proposed to explain plasma tail phenomena. Seven disconnection events were observed in the comet P/Halley data, two in the Austin data, and none for the other comets. Analysis of these data suggests that while the crossing of the solar neutral sheet (the sector boundary) is a prominent factor in the production of a disconnection event, it is likely that several mechanisms are at work. A sector boundary crossing has been ruled out as the cause of either the 1986 April 26 P/Halley disconnection or the 1990 May 5/6 Austin disconnection. The motions of the disconnection events, knots, and condensations in the tails were seen to increase from 30-60 km/s near the nucleus (within 10(exp 6) km) to 80-100 km/s at 10(exp 7) km, consistent with either bulk motion or Alfven waves. Distinguishing between the two cases is not possible with these data. It was found that although the tail ray rotation rate slows as the ray approaches the tail axis, it is not a good indicator of the solar wind speed. Historical plasma tail data are also used to look for clues as to why some comets form well-developed plasma tails and others do not.

Farnham, Tony L.↗
NASA NTRS1996

Aerostructural Vortical Flow Interactions with Applications to F/A-18 and F-117 Tail Buffet

The buffet response of the flexible twin-tail configuration of the F/A-18 and a generic F-111 aircraft are computationally simulated and experimentally validated. The problem is a multidisciplinary one which requires the sequential solution of three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations. The second set is the aeroelastic equations for bending and torsional twin-tail responses. The third set is the grid-displacement equations which are used to update the grid coordinates due to the tail deflections. The computational models consist of a 76 deg. swept back, sharp edged delta wing of aspect ratio of one and a swept-back F/A-18 or F-117 twin-tail. The configuration is pitched at 30 deg. angle-of-attack. The problem is solved for the initial flow conditions with the twin tails kept rigid. Next, the aeroelastic equations of the tails are turned on along with the grid-displacement equations to solve for the bending and torsional tails responses due to the unsteady loads produced by the vortex breakdown flow of the leading-edge vortex cores of the delta wing. Several spanwise locations of the twin tails are investigated. The computational results are validated using several existing experimental data.

Kandil, Osama A.↗
NASA NTRS1998

Magnetospheric Substorms and Tail Dynamics

This grant funded several studies of magnetospheric substorms and their effect on the dynamics of the earth's geomagnetic tail. We completed an extensive study of plasmoids, plasma/magnetic field structures that travel rapidly down the tail, using data from the ISEE 3 and IMP 8 spacecraft. This study formed the PhD thesis of Mark Moldwin. We found that magnetically plasmoids are better described as flux-ropes (twisted magnetic flux tubes) rather than plasma bubbles, as had been generally regarded up to that point (Moldwin and Hughes, 1990; 1991). We published several examples of plasmoids observed first in the near tail by IMP 8 and later in the distant tail by ISEE 3, confirming their velocities down tail. We showed how the passage of plasmoids distorts the plasma sheet. We completed the first extensive statistical survey of plasmoids that showed how plasmoids evolve as they move down tail from their formation around 30 RE to ISEE 3 apogee at 240 RE. We established a one-to-one correspondence between the observation of plasmoids in the distant tail and substorm onsets at earth or in the near tail. And we showed that there is a class of plasmoid-like structures that move slowly earthward, especially following weak substorms during northward IMF. Collectively this work constituted the most extensive study of plasmoids prior to the work that has now been done with the GEOTAIL spacecraft. Following our work on plasmoids, we turned our attention to signatures of substorm onset observed in the inner magnetosphere near geosynchronous orbit, especially signatures observed by the CRRES satellite. Using data from the magnetometer, electric field probe, plasma wave instrument, and low energy plasma instrument on CRRES we were able to better document substorm onsets in the inner magnetosphere than had been possible previously. Detailed calculation of the Poynting flux showed energy exchange between the magnetosphere and ionosphere, and a short burst of tailward convective flow just prior to onset, suggesting the active role of the ionosphere in the onset process, and adding credibility to the ballooning instability theory of substorm onset. This grant also supported a number of other substorm studies and reviews. These are represented by the list of publications and meeting presentations resulting out of this grant.

Hughes, W. Jeffrey↗
NASA NTRS1998

Effectiveness of Flow Control for Alleviation of Twin-Tail Buffet

Effectiveness of active flow control for twin- tail buffet alleviation is investigated. Tangen- tial leading-edge blowing (TLEB) and flow suction along the vortex cores (FSVC) of the lead- ing edges of the delta wing are used to delay the vortex breakdown flow upstream of the twin tail. The combined effect of the TLEB and FSVC is also investigated. A parametric study of the effects of the spanwise position of the suction tubes and volumetric suction flow rate on the twin-tail buffet response are also investigated. The TLEB moves the path of leading-edge vortices laterally towards the twin tail, which increases the aero- dynamic damping on the tails. The FSVC effectively delays the breakdown location at high angles of attack. The computational model consists of a sharp-edged delta wing of aspect ratio one and swept-back flexible twin tail with taper ratio of 0.23. This complex multidisciplinary problem is solved sequentially using three sets of equations for the fluid flow, aeroelastic response and grid deformation, on a dynamic multi-block grid structure. The computational model is pitched at 30 deg. angle of attack. The freestream Mach number and Reynolds number are 0.3 and 1.25 million, respectively. The model is investigated for the inboard position of the twin tails, which corresponds to a separation distance between the twin tails of 33% of the wing span.

Sheta, Essam F.↗
NASA NTRS1998

Effect of Configuration Pitching Motion on Twin Tail Buffet Response

The effect of dynamic pitch-up motion of delta wing on twin-tail buffet response is investigated. The computational model consists of a delta wing-twin tail configuration. The computations are carried out on a dynamic multi-block grid structure. This multidisciplinary problem is solved using three sets of equations which consists of the unsteady Navier-Stokes equations, the aeroelastic equations, and the grid displacement equations. The configuration is pitched-up from zero up to 60 deg. angle of attack, and the freestream Mach number and Reynolds number are 0.3 and 1.25 million, respectively. With the twin tail fixed as rigid surfaces and with no-forced pitch-up motion, the problem is solved for the initial flow conditions. Next, the problem is solved for the twin-tail response for uncoupled bending and torsional vibrations due to the unsteady loads on the twin tail and due to the forced pitch-up motion. The dynamic pitch-up problem is also solved for the flow response with the twin tail kept rigid. The configuration is investigated for inboard position of the twin tail which corresponds to a separation distance between the twin tail of 33% wing chord. The computed results are compared with the available experimental data.

Sheta, Essam F.↗
NASA NTRS1999

Adaptive Suction and Blowing for Twin-Tail Buffet Control

Adaptive active flow control for twin-tail buffet alleviation is investigated. The concept behind this technique is to place control ports on the tail outer and inner surfaces with flow suction or blowing applied through these ports in order to minimize the pressure difference across the tail. The suction or blowing volume flow rate from each port is proportional to the pressure difference across the tail at this location. A parametric study of the effects of the number and location of these ports on the buffet response is carried out. The computational model consists of a sharp-edged delta wing of aspect ratio one and swept-back flexible twin tail with taper ratio of 0.23. This complex multidisciplinary problem is solved sequentially using three sets of equations for the fluid flow, aeroelastic response and grid deformation, using a dynamic multi-block grid structure. The computational model is pitched at 30 deg angle of attack. The freestream Mach number and Reynolds number are 0.3 and 1.25 million, respectively. The model is investigated for the inboard position of the twin tails, which corresponds to a separation distance between the twin tails of 33% of the wing span. Comparison of the time history and power spectral density responses of the tails for various distributions of the control ports are presented and discussed.

Kandil, Osama A.↗
DOE OSTI2023

Modeling the Yaw Behavior of Tail Fins for Small Wind Turbines: November 22, 2021 - May 21, 2024

This report describes the aerodynamic modelling of the yaw behavior of tail fins for small wind turbines (SWTs). The analysis is based on unsteady slender body theory (USBT) and is formulated to be used with the proposed tail fin module to be added to OpenFAST. Linearized USBT, which has been applied in the past to SWT tail fins, is developed in three main ways. First, USBT is extended to high yaw angles and aspect ratios by modelling the associated nonlinear vortex dynamics and the chordwise load distribution respectively. Second, we consider the effect of time-varying wind speed. The extended theory is compared to recent unpublished measurements at the University of Perugia, Italy, for the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40 degrees and -80 degrees ; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Further, the friction in the model tail fin bearings was measured and modelled. The constants in the aerodynamic models were taken from the literature but significant improvement in accuracy is achieved by using system identification techniques to optimize the values. This leads to the third main finding: extended USBT is accurate for all generic tail fin shapes that we considered and is, therefore, very suitable for inclusion in aeroelastic codes for SWTs. The final development is of a general nonlinear equation for yaw response that is simpler than the extended USBT and is also suitable for inclusion in OpenFAST. The two nonlinear models are used to highlight the geometric requirements for good tail fin design.

distributed wind↗
NASA NTRS1946

Tank tests to determine the effect of varying design parameters of planing-tail hulls II : effect of varying depth of step, angle of after- body keel, length of afterbody chine, and gross load

The second part of a series of tests made in Langley tank no. 2 to determine the effect of varying design parameters of planing-tail hulls is presented. Results are given to show the effects on resistance characteristics of varying angle of afterbody keel, depth of step, and length of afterbody chine. The effect of varying the gross load is shown for one configuration. The resistance characteristics of planing-tail hulls are compared with those of a conventional flying-boat hull. The forces on the forebody and afterbody of one configuration are compared with the forces on a conventional hull. Increasing the angle of afterbody keel had small effect on hump resistance and no effect on high-speed resistance but increased free-to-trim resistance at intermediate speeds. Increasing the depth of step increased hump resistance, had little effect on high-speed resistance, and increased free-to-trim resistance at intermediate speeds. Omitting the chines on the forward 25 percent of the afterbody had no appreciable effect on resistance. Omitting 70 percent of the chine length had almost no effect on maximum resistance but broadened the hump and increased spray around the afterbody. Load-resistance ratio at the hump decreased more rapidly with increasing load coefficient for the planing-tail hull than for the representative conventional hull, although the load-resistance ratio at the hump was greater for the planing-tail hull than for the conventional hull throughout the range of loads tested. At speeds higher than hump speed, load-resistance ratio for the planing-tail hull was a maximum at a particular gross load and was slightly less at heavier and lighter gross loads. The planing-tail hull was found to have lower resistance than the conventional hull at both the hump and at high speeds, but at intermediate speeds there was little difference. The lower hump resistance of the planing-tail hull was attributed to the ability of the afterbody to carry a greater percentage of the total load while maintaining a higher value of load-resistance ratio.

HULLS - RESISTANCE - TANK TESTS (NACA-#2)↗