SEARCH · Search NASA
Results for “Thermogravimetric analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)
A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.
Energetic Copolymers From LLM-105 and Aliphatic Isocyanates
Energetic polymers typically feature fuel-rich backbones with pendant oxidizing explosophores, which are used to modify pressure and temperature characteristics in energetic formulations. However, these pendant explosophores generally increase sensitivity and decrease the thermal stability of the polymer in the condensed phase. Direct polymerization of insensitive high explosives (IHEs) bearing polymerizable functionalities, such as amines, provides a synthetic platform for deriving tunable energetic materials. Here, this work demonstrates the first direct polymerization of the IHE 2,6-diamino-3,5-dinitropyrazine-1-oxide (LLM-105) with aliphatic isocyanate comonomers to yield an energetic copolyurea (PUa1) and an energetic copolyurea network (PUa2). 1 H and 13 C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR) confirm copolyurea synthesis. PUa1 exhibited branching reactions commonly found in polyurea syntheses, and these side reactions were suppressed in PUa2 through use of a polyfunctional isocyanate. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) demonstrate the energetic IHE based polyurea preserves the energetic decomposition of the parent monomer LLM-105 in PUa1 (1203 J g −1 ) and PUa2 (687 J g −1 ), albeit with reduced thermal stability with peak decomposition temperatures of 235°C and 233°C, respectively. This work presents a new approach for generating energetic polymers from IHE cores with tunable energetic, thermal, and structural characteristics.
Thermal Stability of a Eutectic Mixture of Bis(2,2-dinitropropyl) Acetal and Formal: Part C. Kinetic Compensation Effect
Here, the aging behavior of a eutectic mixture of bis(2,2-dinitropropyl) acetal and formal [called NP here] has been studied in various atmospheres [dry (air or nitrogen) versus wet] at temperatures 70 °C and below. The properties of aged samples were analyzed using Fourier transform infrared (FTIR) spectroscopy, Karl Fischer (KF) titration, liquid chromatography/mass spectrometry (LC/MS), and thermogravimetric analysis (TGA) over a period of three years. The results indicate that at aging temperatures up to 55 °C, the initial rates of water production from nitrous acid (HONO) formation and decomposition into the water, NO, and NO 2 follows a 1st order rate law and the rate constants follow an Arrhenius law as a function of temperature. The activation energies and pre-factors for water and volatiles production yield a single linear kinetic compensation plot, suggesting a common degradation pathway between NP and the various combinations of its constituents. Within a narrow temperature range, around 55 °C, a trace amount of water in NP stabilizes its properties by preventing HONO elimination. When the aging temperature is substantially higher than 55 °C, the nature of the degradation mechanism changes. It is suspected that the degradation products of NO x , water, and HNO 3 serve as catalysts to auto-catalyze (kinetics beyond the 1st order) and further degrade NP. The effect of headspace volume on this auto-catalytic process will be discussed.
Towards a heat- and mass-balanced kinetic model of TATB decomposition
We report TATB (1,3,5-triamino-2,4,6-trinitrobenzene) was thermally degraded by two small-scale analytical methods – simultaneous differential scanning calorimetry and thermogravimetric analysis (SDT) and a hot-stage microscope with Fourier Transform Infrared (FTIR) analysis capabilities. SDT used ramped heating, isothermal soaking, and thermal pretreatment at various conditions. The heat flow and mass loss were monitored during various treatment conditions to derive chemical decomposition kinetics and Arrhenius parameters. FTIR experiments used isothermal heating, and changes were monitored spectroscopically. Solid samples generated at specific conditions were collected from both methods and were analyzed by DMSO extraction followed by chemical speciation by optical and mass spectrometric methods. Characterization provided the following reaction insights: TATB decreases in a sigmoidal pattern in isothermally heated samples. Other soluble products gradually increase in concentration and then abruptly decline in concentration during the second exotherm, such as diamino-dinitro-benzofurazan and amino-nitro-benzodifurazan. FTIR showed gradual changes in the amino and nitro functionality, shifting positions and decreasing intensity for the first 40 min. Then the solid gradually appeared more like an amorphous C with N incorporated, similar to previous studies on thermally degraded TATB-type materials. Extracted residues (DMSO-soluble components removed) examined by FTIR showed an abrupt change in chemical composition between 40- and 45-min isothermal treatment, indicating early forming solids are different than later forming residues. A reliable mass- and energy-balanced global reaction network must include at least two autocatalytic reactions, either in parallel or series, and at least one must have an explicit initiation reaction having a low activation energy.
Thermal Decomposition Kinetics of 4,6‐Diamino‐5,7‐dinitro‐benzo‐furazan
This experimental study investigated the thermal decomposition kinetics of 4,6-diamino-5,7-dinitro-benzo-furazan (referred to as F1 hereafter)—an important decomposition product of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB—a prototypical insensitive high explosive). Simultaneous differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and mass spectrometry (MS) measurements were employed to determine the decomposition kinetics of F1 and to track the evolution of product gases. The DSC profiles were measured at 10 different heating rates between 0.025°C/min and 10°C/min. The measured exotherms were influenced by F1 melting at heating rates above 0.25°C/min, and corresponding changes in decomposition enthalpy and TGA mass-loss-rate profiles indicated a transition from solid-to-gas decomposition to an increasing contribution from liquid-to-gas decomposition. Analysis of low-heating-rate DSC data between 0.025°C/min and 0.17°C/min with the extended Prout–Tompkins model yielded an activation energy of 305 kJ/mol for solid-to-gas F1 decomposition, higher than previous values inferred from TATB decomposition models involving F1. This study provides the first direct experimental determination of the energy barrier for F1 decomposition. MS measurements showed that the major gaseous products matched species previously reported for TATB decomposition (e.g., CO 2 , HCN, C 2 N 2 , etc.), with water identified as the dominant product. Furthermore, these results provide important experimental constraints for improving chemical kinetics models of TATB decomposition and for predicting the reactivity, stability, and safety of TATB-based high explosives under long-term aging conditions and abnormal thermal environments.
Engineering Supramolecular Hybrid Architectures with Directional Organofluorine Bonds
Understanding how chemical modifications alter the atomic‐scale organization of materials is of fundamental importance in materials engineering and the target of considerable efforts in computational prediction. Incorporating covalent and noncovalent interactions in designing crystals while “piggybacking” on the driving force of molecular self‐assembly has augmented efforts to understand the emergence of complex structures using directed synthesis. In this work, microcrystalline powders of the silver 2‐, 3‐, and 4‐fluorobenzenethiolates are prepared and their structures are resolved by small‐molecule serial femtosecond X‐ray crystallography. These three compounds enable the emergence and role of supramolecular synthons in the crystal structures of 3D metal‐organic chalcogenolates to be examined. The unique divergence in their optoelectronic, morphological, and structural behaviors is assessed. The extent of CHF interactions and their influence on the structure and the observed trends in the thermal stability of the crystals are quantified through theoretical calculations and thermogravimetric analysis.
Thermal stability of filler‐based ethylene/vinyl acetate/vinyl alcohol terpolymer in nitroplasticizer oxidative environment
Abstract To study the thermal stability of ethylene/vinyl acetate/vinyl alcohol (EVA‐OH) composite with filler particles, systematic thermogravimetric analysis (TGA) investigation was conducted in both nonisothermal and isothermal modes. The effect of polymer concentration on the aging behavior of EVA‐OH was investigated in the nitroplasticizer (NP) environment. Fourier transform infrared spectroscopy was used to probe chemical structural changes in the EVA‐OH polymer before and after thermal aging. The results suggest that filler addition accelerates the rate of NP exudation out of the EVA‐OH composites and deteriorates the thermal stability of NP at moderate temperatures (up to 70°C). The degradation of NP, in turn, accelerates the degradation of EVA‐OH polymer in its composite form through oxidation and hydrolysis indicating the importance of antioxidants in such phase blends.
Effect and measurement of residual water in CaCl 2 intended for use as electrolyte in molten salt electrochemical processing
We report CaCl 2 has applications for electrochemical processing of nuclear materials. Thermal dehydration leads to formation of oxide ions, which are shown to react and cause precipitation of dissolved CeCl 3 that was selected as a surrogate for actinide chlorides. Thus, measurement of residual water in CaCl 2 is an essential capability. Thermogravimetric analysis (TGA) was shown to underestimate starting water concentration. Subsequent analysis of solid samples via acid–base titration and cyclic voltammetry (CV) of the molten salt yielded consistent values within 5% for residual water. Hydroxides were shown to be unstable, thus oxygen is retained as oxide ions. Thus, total water in a sample of CaCl 2 can be quantified by combining TGA with with either CV of molten salt or titration of salt samples. The importance of quantifying residual water in the salt was demonstrated by showing that cerium chloride (surrogate for actinide chlorides) will react with oxide ions in CaCl 2 to form insoluble oxides and oxychlorides.
Quaternary i-MAX Phases (Mo 2/3 RE 1/3 ) 2 AlC (RE: Dy, Tb, Er): Experimental Characterization and First-Principles Insights into their Fundamental Properties
Rare earth (RE)-based materials have unique electronic, magnetic, and optical properties, leading to the recent discovery of atomically layered solids with the chemical formula (M' 2/3 RE 1/3 ) 2 AlC, which have since garnered significant attention in the scientific community. This study aims to synthesize, characterize, and investigate the structural and thermal stability of the RE i-MAX phases. We prepared i-MAX phases using molybdenum (Mo) as M′ and RE elements as Dy, Tb, and Er, namely (Mo 2/3 Dy 1/3 ) 2 AlC, (Mo 2/3 Tb 1/3 ) 2 AlC, and (Mo 2/3 Er 1/3 ) 2 AlC. Structural characterization through x-ray diffraction (XRD) and Raman spectroscopy confirms the formation of the RE-based i-MAX phase, along with the presence of minor impurity phases in the alloys. Thermogravimetric analysis (TGA) conducted up to 1000°C under ambient conditions reveals that the i-MAX phases remain thermally stable up to approximately 450°C, beyond which oxidation leads to a noticeable weight gain in all samples. Differential scanning calorimetry (DSC) measurements during heating and cooling cycles show endothermic and exothermic peaks for (Mo 2/3 Dy 1/3 ) 2 AlC i-MAX in the 410–420°C range, indicating a temperature-induced minor atomic arrangement. In contrast, these peaks are absent in the Tb- and Er-based i-MAX phases. These findings offer valuable insights into the thermal behavior and stability of these i-MAX phases under thermal stress, contributing to a deeper understanding of their unique properties. Furthermore, first-principles density functional theory (DFT) calculations were performed to investigate the electronic and optical properties of the i-MAX phases. The results reveal their metallic nature, with pronounced contributions from Mo and RE elements near the Fermi level and within the conduction band.
Iron Oxide Reduction Rate Affects Iron Product Morphology
Magnetite concentrates from different parts of the Mesabi Range, exhibiting varying tendencies to encapsulate, were reduced using thermogravimetric analysis (TGA) and a high-temperature confocal scanning laser microscope (CSLM). Gas-phase mass-transfer conditions were intentionally varied by employing two reactors with different geometries: the TGA produced significantly slower reduction, whereas the CSLM setup yielded reduction rates up to 20 times faster under mass-transfer-controlled conditions. A preliminary mechanism is proposed to explain the transition from a porous iron product to a dense encapsulating layer. Encapsulation is interpreted as the outcome of competition between pore creation, driven by the reduction rate, and pore elimination, driven by surface diffusion. When pore formation is insufficient to counteract pore coarsening, a dense iron layer develops and restricts further reduction.
The role of precursor decomposition in the formation of samarium doped ceria nanoparticles via solid-state microwave synthesis
The impact on the final morphology of ceria (CeO 2 ) nanoparticles made from different precursors (commercial: cerium acetate/nitrate) and in house: cerium tri(methylsilyl)amide (Ce-TMSA)) via a microwave solid state reaction has been determined. In all instances, powder X-ray diffraction indicated that the cubic fluorite CeO 2 phase (PDF# 04–004-9150, with the space group Fm-3 m) had formed. Scanning electron microscopy (SEM) images revealed spherical nanoparticles were produced from the Ce-TMSA precursor. The commercial acetate and nitrate precursors produced particles with irregular morphology. The roles of the precursor decomposition and binding energy in the synthesis of the nanocrystals with various morphologies, as well as a possible growth mechanism, were evaluated based on experimental and computational data. The formation of spherical shaped nanoparticles was determined to be due to the preferential single-step decomposition of the Ce-TMSA as well as the low activation energy to overcome decomposition. Due to the complicated decomposition of the commercial precursors and high activation energy the resulting particles adopted an irregular morphology. Highly uniform samarium doped ceria (Sm x Ce 1-x O 2-δ ) nanospheres were also synthesized from Ce-TMSA and samarium tri(methylsilyl)amide (Sm-TMSA). The effects of reaction time and temperature, on the final morphology were observed through SEM. The rapid single-step decomposition of TMSA-based precursors as observed through thermogravimetric analysis (TGA) and confirmed through the calculation of potential energy surfaces and binding energies from density functional theory (DFT) calculations, indicated that nanoparticle formation follows LaMer’s classical nucleation theory.
Polymer-iron oxide hybrid films for controlling electrokinetic properties
Electrokinetic phenomena at polymer-water interfaces are central to technologies for water purification, ion separations, and energy conversion, yet the ability to systematically control polymer surface charge and associated electrokinetic processes remains limited. Here, we demonstrate a simple liquid-phase infiltration (LPI) method to synthesize polymer–metal oxide hybrid films with controllable interfacial properties. Hydroxy-terminated poly(2-vinylpyridine) (P2VP-OH) brushes grafted to silicon substrates were infiltrated with iron nitrate from ethanolic solution, followed by low-temperature thermal treatment to convert the infiltrated precursor into iron oxide. Spectroscopic ellipsometry, X-ray photoelectron spectroscopy, and thermogravimetric analysis confirmed oxide incorporation and hybrid film formation without polymer degradation. Electrokinetic measurements reveal that the hybrid films acquire the electrokinetic properties of the infiltrated oxide, with concentration-dependent streaming potentials and surface conductivities closely matching those of pure iron oxide films. These results establish metal oxide infiltration as a scalable and low-cost strategy for controlling interfacial charge in polymer surfaces. The approach introduces new materials and design parameters for tailoring ion selectivity, transport, and energy conversion, with broad implications for the development of advanced membranes, electrokinetic harvesting devices, and polymer-supported oxide electrodes.
Structural and physicochemical insights into pH-responsive poly(DEAEMA- co -HEMA)-grafted mesoporous silica nanoparticles
Mesoporous silica nanoparticles (SiO 2 ) grafted with responsive polymer shells are versatile hybrid systems. Understanding their three-dimensional organization in the hydrated state remains a significant challenge. Here, in this study, SiO 2 nanoparticles were functionalized with a poly(DEAEMA-co-HEMA) shell via a “grafting-from” polymerization strategy in aqueous media. Successful surface modification was confirmed by FTIR, thermogravimetric analysis, transmission electron microscopy, X-ray photoelectron spectroscopy, N 2 sorption, and ζ-potential, yielding grafting contents of 22% (p1 DEAEMA-co-HEMA ) and 49% (p2 DEAEMA-co-HEMA ). Small-angle neutron scattering (SANS) with solvent contrast variation was employed to elucidate the solution-state core–shell architecture of p1 and p2 hybrids at pH 2, where the grafted polymer shell is protonated and highly hydrated. Near contrast matching of the silica core, theoretically estimated at 58% D 2 O, suppressed the scattering intensity, enhancing sensitivity to the polymer shell. Constrained core–shell ellipsoid modeling across solvent contrasts revealed a systematic increase in shell thickness, overall particle dimensions, and shell anisotropy with increasing grafting content. In solution, the hydrated polymer shells were markedly more extended and structurally anisotropic than suggested by dry-state techniques structural characterization, highlighting the importance of solution-state structural analysis for accurately describing grafted polymer architectures.
Flash graphene from rubber waste
Most conventional production processes for graphene are time-consuming, solvent-intensive, and energetically demanding. To circumvent these limitations for mass production, flash Joule heating (FJH) has been shown to be an effective method to synthesize graphene. Here, methods for optimizing production of graphene from rubber waste feedstocks are shown. Through careful control of system parameters, such as pulse voltage and pulse time, turbostratic flash graphene (tFG) can be produced from rubber waste. It is characterized by Raman spectroscopy, X-ray diffraction and thermogravimetric analysis. Here, the resulting tFG can be easily exfoliated and dispersed into various solvents because of its turbostratic arrangement. Addition of tFG into Portland cement results in a significant increase in the compressive strength of the composite. From a materials perspective, FJH offers a facile and inexpensive method for producing high quality tFG from rubber waste materials, which would otherwise be disposed of in landfills or burned for fuel. FJH allows for upcycling of low-value rubber waste into high-value carbon nanomaterials for use as reinforcing additives.
Sorbent-based oxygen separation with YBC114 for energy storage systems
In our report we aimed to design, build, and evaluate an oxygen separation system to provide an inert sweep gas with low oxygen partial pressure (pO2) to redox-active thermochemical energy conversion reactors for a range of applications, including two-step redox cycles for thermochemical energy storage, water splitting, and carbon-dioxide splitting. The separation is based on an oxygen-selective sorbent, YBaCo4O7+δ (YBC114), which has excellent oxygen sorption and desorption properties demonstrated in our previous work. The oxygen separation performance of YBC114 was comprehensively studied by thermogravimetric analysis, sorption breakthrough experiments, and temperature swing sorption - desorption cycles. The results reveal that YBC114 can produce inert sweep gas with an oxygen concentration of less than 100 ppmv for at least 20 min during the thermal swing adsorption (TSA) cycle with the current sorption bed configuration, and the performance is consistent from cycle to cycle. The optimal sorption and desorption temperatures for the TSA process with YBC114 are determined to be 300 °C and 500 °C, respectively. Although challenges remain for the current separation system (e.g., high sorption temperature and slow kinetics), this study demonstrates the potential to use the oxygen-selective sorbent to produce an inert sweep gas, the feasibility of the oxygen separation concept, and guides new sorbent material development to make this application economically practical. A simple procedure is described for designing the YBC114 oxygen separation process.
Sr 2 MnO 4 as a reactive CO 2 sorbent for sorption-enhanced steam reforming of biogas to green hydrogen
Sorption-enhanced steam biogas reforming is an attractive approach for hydrogen production from renewable resources, with the performance of the CO 2 sorbents being a critical factor. In this study, Sr 2 MnO 4 was investigated as a redox-activated CO 2 sorbent for sustainable hydrogen production from biogas. The Sr 2 MnO 4 sorbents exhibited a CO 2 sorption capacity of over 26 g per 100 g of sorbents, along with excellent cyclic stability in thermogravimetric analysis. Complete regeneration of the sorbent was achieved with a relatively small temperature swing (100 °C). Fixed-bed reactor experiments further demonstrated the application of Sr 2 MnO 4 sorbents in sorption-enhanced steam biogas reforming. Biogas simulants with varying CO 2 contents were converted to ~94 vol% H 2 before CO 2 breakthrough. Stable CO 2 capacity and hydrogen production were maintained over 20 cycles. In addition, optimization of the regeneration duration enabled the generation of highly pure CO 2 and more efficient use of O 2 . These results support the feasibility of biogas-to‑hydrogen conversion with net-negative carbon emissions through integration with CO 2 capture and sequestration.
Engineered Cementitious Composites (ECC) with limestone calcined clay cement (LC 3 )
Recent research have recognized that coupled use of calcined clay, limestone and cement clinker in concrete is viable to reduce environmental footprints at manufacture and to enhance material durability. In this study, a novel application of the limestone calcined clay cement (LC 3 ) is demonstrated by substituting the Ordinary Portland Cement (OPC) in Engineered Cementitious Composites (ECC). The composite mechanical properties including σ-δ and σ-ε relationships and residual crack widths were evaluated to 28 days under uniaxial tension. Matrix chemistry was characterized using thermogravimetric analysis and X-ray diffraction, while the pore structure of matrices and composites was analyzed using mercury intrusion porosimetry. The LC 3 -based ECC showed more rapid early strength development but lower 28-day strength (~32 MPa) due to a 20% higher water-to-solid ratio for attaining adequate workability and fiber dispersion. Nevertheless, the tensile strain capacity of LC 3 -based ECC achieved over 6% with an average residual crack width less than 50 μm. Additionally, the composite pore structure exhibited a decreasing volume fraction of large pores and voids (>100 nm) after substituting LC 3 for OPC. Here, the use of LC 3 marginally decreased the embodied material energy and cost, but led to about 32% and 28% reductions in CO 2 emissions compared to traditional OPC-based ECC and concrete, respectively. As a preliminary study, LC 3 -based ECC shows promise as a greener ductile concrete compared with OPC-based ECC.