Search NASA⌕ Search

SEARCH · Search NASA

Results for “UREA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

UREA/ammonium ion removal system for the orbiting frog otolith experiment

The feasibility of using free urease enzyme and ANGC-101 ion exchange resin to remove urea and ammonium ion for space system waste water applications was studied. Specifically examined is the prevention of urea and ammonia toxicity in a 30-day Orbiting Frog Otolith (OFO) flight experiment. It is shown that free urease enzyme used in conjunction with ANGC-101 ion-exchange resin and pH control can control urea and amonium ion concentration in unbuffered recirculating water. In addition, the resin does not adversely effect the bullfrogs by lowering the concentration of cations below critical minimum levels. Further investigations on bioburden control, frog waste excretion on an OFO diet, a trade-off analysis of methods of automating the urea/ammonium ion removal system and fabrication and test of a semiautomated breadboard were recommended as continuing efforts. Photographs of test equipment and test animals are shown.

Schulz, J. R.↗
NASA NTRS1989

Selective removal of organics for water reclamation

Electrolysis has been investigated as a means of purifying waste water. The feasibility of the direct electrochemical oxidation of urea has been demonstrated. Urea levels were reduced from 1200 ppm to 1 ppm forming the basis for a new approach to urine purification where the only consumable is electrical energy. Preliminary estimates of the energy requirements are 270 W/hr per liter of urine. Urea oxidation rates of around 350 mg urea/hr/m2 were observed. It is anticipated that a 1 m2 geometric area of electrode could treat urine for a crew of several persons. The low levels of organic contaminants resulting from this treatment indicate that the approach may have an impact as a post treatment process. Experiments are planned to investigate this later possibility.

Murphy, Oliver J.↗
NASA NTRS1989

Modern biofuel cells for waste recycling in life support systems

Innovative ways of treating urea in waste water reprocessing for long duration space exploration are being considered. Urea is very stable and therefore there are few effective ways for its decomposition. The feasibility of the use of the enzyme urease is to catalyze the hydrolysis of urea to ammonia and carbon dioxide is discussed, including a methodology, potential problems, the capabilities and advantages of such a system.

Chen, L.↗
NASA NTRS1994

Short term responses of nitrogen trace gas emissions to nitrogen fertilization in tropical sugar cane: Variations due to soils and management practices

Nitrogen (N) fertilization of agricultural systems is thought to be a major source of the increase in atmospheric N2O; NO emissions from soils have also been shown to increase due to N fertilization. While N fertilizer use is increasing rapidly in the developing world and in the tropics, nearly all of our information on gas emissions is derived from studies of temperate zone agriculture. Using chambers, we measured fluxes of N2O and NO following urea fertilization in tropical sugar cane systems growing on a variety of soil types in the Hawaiian Islands, USA. On the island of Maui, where urea is applied in irrigation lines and soils are mollisols and inceptisols, N2O fluxes were elevated for a week or less following fertilization; maximum average fluxes were typically less than 30 ng cm(exp -2)/ h. NO fluxes were often an order of magnitude less than N2O. Together, N2O and NO represented from 0.01 - 0.5% of the applied N. In fields on the island of Hawaii, where urea is broadcast on the surface and soils are andisols, N2O fluxes were similar in magnitude to Maui but remained elevated for much longer periods after fertilization. NO emissions were 2-5 times higher than N2O through most of the sampling periods. Together the gases loss represented approximately 1. 1 - 3% of the applied N. Laboratory studies indicate that denitrification is a critical source of N2O in Maui, but that nitrification is more important in Hawaii. Experimental studies suggest that differences in the pattern of N2O/NO and the processes producing them are a result of both carbon availability and placement of fertilizer, and that the more information-intensive fertilizer management practice results in lower emissions.

Matson, P. A.↗
NASA NTRS1995

An efficient prebiotic synthesis of cytosine and uracil

In contrast to the purines, the routes that have been proposed for the prebiotic synthesis of pyrimidines from simple precursors give only low yields. Cytosine can be synthesized from cyanoacetylene and cyanate; the former precursor is produced from a spark discharge in a CH4/N2 mixture and is an abundant interstellar molecule. But this reaction requires relatively high concentrations of cyanate (> 0.1 M), which are unlikely to occur in aqueous media as cyanate is hydrolysed rapidly to CO2 and NH3. An alternative route that has been explored is the reaction of cyanoacetaldehyde (formed by hydrolysis of cyanoacetylene) with urea. But at low concentrations of urea, this reaction produces no detectable quantities of cytosine. Here we show that in concentrated urea solution--such as might have been found in an evaporating lagoon or in pools on drying beaches on the early Earth--cyanoacetaldehyde reacts to form cytosine in yields of 30-50%, from which uracil can be formed by hydrolysis. These reactions provide a plausible route to the pyrimidine bases required in the RNA world.

Non-NASA Center↗
NASA NTRS2012

Strategies for Stabilizing Nitrogenous Compounds in ECLSS Wastewater: Top-Down System Design and Unit Operation Selection with Focus on Bio-Regenerative Processes for Short and Long Term Scenarios

Water recycling and eventual nutrient recovery is crucial for surviving in or past low earth orbit. New approaches and syste.m architecture considerations need to be addressed to meet current and future system requirements. This paper proposes a flexible system architecture that breaks down pretreatment , steps into discrete areas where multiple unit operations can be considered. An overview focusing on the urea and ammonia conversion steps allows an analysis on each process's strengths and weaknesses and synergy with upstream and downstream processing. Process technologies to be covered include chemical pretreatment, biological urea hydrolysis, chemical urea hydrolysis, combined nitrification-denitrification, nitrate nitrification, anammox denitrification, and regenerative ammonia absorption through struvite formation. Biological processes are considered mainly for their ability to both maximize water recovery and to produce nutrients for future plant systems. Unit operations can be considered for traditional equivalent system mass requirements in the near term or what they can provide downstream in the form of usable chemicals or nutrients for the long term closed-loop ecological control and life support system. Optimally this would allow a system to meet the former but to support the latter without major modification.

Lunn, Griffin M.↗
DOE OSTI2023

Electrochemical C–N Bond Formation within Boron Imidazolate Cages Featuring Single Copper Sites

Electrocatalysis expands the ability to generate industrially relevant chemicals locally and on-demand with intermittent renewable energy, thereby improving grid resiliency and reducing supply logistics. Herein, we report the feasibility of using molecular copper boron-imidazolate cages, BIF-29(Cu), to enable coupling between the electroreduction reaction of CO 2 (CO 2 RR) with NO 3 – reduction (NO 3 RR) to produce urea with high selectivity of 68.5% and activity of 424 μA cm –2 . Remarkably, BIF-29(Cu) is among the most selective systems for this multistep C–N coupling to-date, despite possessing isolated single-metal sites. The mechanism for C–N bond formation was probed with a combination of electrochemical analysis, in situ spectroscopy, and atomic-scale simulations. We found that NO 3 RR and CO 2 RR occur in tandem at separate copper sites with the most favorable C–N coupling pathway following the condensation between *CO and NH 2 OH to produce urea. In conclusion, this work highlights the utility of supramolecular metal–organic cages with atomically discrete active sites to enable highly efficient coupling reactions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Use of microbial carbonation process to enable self‑carbonation of reactive MgO cement mixes

The low hydration and carbonation of reactive MgO cement (RMC) under ambient conditions causes prolonged setting and low compressive strengths (~4 MPa). This study proposed a unique technique which led to the enhancement of the hydration and carbonation processes via the synergistic combination of microbial carbonation process (MCP) with a hydration agent (HA) that enabled the self‑carbonation of RMC-based mixes without using of any special curing environments. Through hydrolysing urea (CO(NH{sub 2}){sub 2}) using ureolytic bacteria, CO{sub 3}{sup 2−} ions were produced to facilitate the carbonation of dissolved Mg{sup 2+} ions to form hydrated magnesium hydroxy carbonates (HMHCs). The self‑carbonation of RMC enabled by the MCP resulted in formation of brucite with a poor crystallinity and its rapid conversion into HMHCs, which improved the setting time and compressive strength of RMC-based samples. The simultaneous use of MCP with 2 M urea and HA revealed HMHCs with improved morphologies, resulting in the highest compressive strength (~15 MPa).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sensitive Top-Down Proteomics Analysis of a Low Number of Mammalian Cells Using a Nanodroplet Sample Processing Platform

Top-down proteomics is a powerful tool for characterizing genetic variations and post-translational modifications at intact protein level. That being said, one significant technical gap of top-down proteomics is the inability to analyze low amount of biological samples, which limits its access to isolated rare cells, fine-needle aspiration biopsies, and tissue substructures. Herein, we developed an ultrasensitive top-down platform by incorporating a microfluidic sample preparation system, termed nanoPOTS (Nanodroplet Processing in One pot for Trace Samples), into a top-down proteomics workflow. A unique combination of a nonionic detergent dodecyl-ß-D-maltopyranoside (DDM) with urea as protein extraction buffer significantly improved both protein extraction efficiency and sample recovery. We hypothesize that the DDM detergent improves protein recovery by efficiently reducing non-specific adsorption of intact proteins on container surfaces, while urea serves as a strong denaturant to disrupt noncovalent complexes and release intact proteins for downstream analysis. The nanoPOTS-based top-down platform reproducibly and quantitatively identified ~170 to ~620 proteoforms from ~70 to ~770 HeLa cells containing ~10 to ~115 ng of total protein. A variety of post-translational modifications including acetylation, myristoylation, and iron binding were identified using only less than 800 cells. We anticipate the nanoPOTS top-down proteomics platform will be broadly applicable in biomedical researches, particularly where clinical specimens are not available in amounts amenable to standard workflows.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Toward Automated Sampling of Polymorph Nucleation and Free Energies with the SGOOP and Metadynamics

Understanding the driving forces behind the nucleation of different polymorphs is of great importance for material sciences and the pharmaceutical industry. This includes understanding the reaction coordinate that governs the nucleation process and correctly calculating the relative free energies of different polymorphs. Here, we demonstrate, for the prototypical case of urea nucleation from the melt, how one can learn such a one-dimensional reaction coordinate as a function of prespecified order parameters and use it to perform efficient biased all-atom molecular dynamics simulations. The reaction coordinate is learnt as a function of the generic thermodynamic and structural order parameters using the “spectral gap optimization of order parameters (SGOOP)” approach [Tiwary, P. and Berne, B. J. Proc. Natl. Acad. Sci. U.S.A. (2016)] and is biased using well-tempered metadynamics simulations. The reaction coordinate gives insights into the role played by different structural and thermodynamics order parameters, and the biased simulations obtain accurate relative free energies for different polymorphs. This includes an accurate prediction of the approximate pressure at which urea undergoes a phase transition and one of the metastable polymorphs becomes the most stable conformation. Here, we believe the ideas demonstrated in this work will facilitate efficient sampling of nucleation in complex, generic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Demonstration of MgCr 2– x Mn x O 4 Spinel Oxide Cathodes in High-Voltage Mg Batteries

Solid-solution oxide spinels with high redox voltages and facile Mg 2+ mobility have been identified as promising candidates for practical, high-voltage cathodes in Mg batteries. In this work, we discuss the development of MgCr 2-x Mn x O 4 [x = 0.5, 1, 1.2] solid-solution spinel oxides as a cathode material and their electrochemical performance paired with an Mg anode in a full cell. This work presents the first demonstration of full cells with these materials. Mg-Cr-Mn spinel oxides with varying Cr and Mn contents were synthesized using alternative synthetic routes for optimal electrochemical performance. High-resolution synchrotron powder X-ray diffraction (PXRD), solid-state nuclear magnetic resonance (NMR) spectroscopy, and electron microscopy showed that these different synthetic routes resulted in changes in structures and particle morphologies, which in turn affect the electrochemical performance. Particularly, the urea coprecipitation synthetic route resulted in high-surface-area particles that enabled lower overpotentials and increased discharge capacity. The high surface area also resulted in expedited structural degradation caused by the irreversible migration of Mg 2+ into normally vacant 16c sites in the spinel lattice. This structural degradation was lessened by using a hydrosauna-urea synthesis method, which decreased the Mg/Mn inversion ratio while retaining high-surface-area particles with good cycling performance. Furthermore, our findings highlight the necessity for high surface area or nanostructured spinel oxide cathodes with minimized Mg-Mn inversion to enable spinel oxide cathodes in Mg full cells.

Mg anode↗
DOE OSTI2020

Effects of nitrogen fertilization and bioenergy crop type on topsoil organic carbon and total Nitrogen contents in middle Tennessee USA

Nitrogen (N) fertilization affects bioenergy crop growth and productivity and consequently carbon (C) and N contents in soil, it however remains unclear whether N fertilization and crop type individually or interactively influence soil organic carbon (SOC) and total N (TN). In a three-year long fertilization experiment in switchgrass (SG: Panicum virgatum L.) and gamagrass (GG: Tripsacum dactyloides L.) croplands in Middle Tennessee USA, soil samples (0–15cm) were collected in plots with no N input (NN), low N input (LN: 84 kg N ha -1 yr -1 in urea) and high N input (HN: 168 kg N ha -1 yr -1 in urea). Besides SOC and TN, the aboveground plant biomass was also quantified. In addition to a summary of published root morphology data based on a separated mesocosm experiment, the root leachable dissolved organic matter (DOM) of both crops was also measured using archived samples. Results showed no significant interaction of N fertilization and crop type on SOC, TN or plant aboveground biomass (ABG). Relative to NN, HN (not LN) significantly increased SOC and TN in both crops. Though SG showed a 15–68% significantly higher ABG than GG, GG showed a 9.3–12% significantly higher SOC and TN than SG. The positive linear relationships of SOC or TN with ABG were identified for SG. However, GG showed structurally more complex and less readily decomposed root DOM, a larger root volume, total root length and surface area than SG. Collectively, these suggested that intensive N fertilization could increase C and N stocks in bioenergy cropland soils but these effects may be more likely mediated by the aboveground biomass in SG and root chemistry and morphology in GG. Future studies are expected to examine the root characteristics in different bioenergy croplands under the field fertilization experiment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine**

Abstract Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy‐extensive Haber‐Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source‐separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF‐808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30‐minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

Guo, Lei↗
DOE OSTI2023

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine

Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy-extensive Haber-Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source-separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF-808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30-minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Field–scale evaluation of ecosystem service benefits of bioenergy switchgrass

Purpose-grown perennial herbaceous species are nonfood crops specifically cultivated for bioenergy production and have the potential to secure bioenergy feedstock resources while enhancing ecosystem services. This study assessed soil greenhouse gas emissions (CO 2 and N 2 O), nitrate (NO 3 -N) leaching reduction potential, evapotranspiration (ET), and water-use efficiency (WUE) of bioenergy switchgrass (Panicum virgatum L.) in comparison to corn (Zea mays L.). The study was conducted on field-scale plots in Urbana, IL, during the 2020–2022 growing seasons. Switchgrass was established in 2020 and urea-fertilized at 56 kg N ha –1 year –1 . Corn management followed best management practices for the US Midwest, including no-till and 202 kg N ha –1 year –1 fertilization, applied as urea–ammonium nitrate (32%). Our results showed lower direct N 2 O emissions in switchgrass compared to corn. Although soil CO 2 emissions did not differ significantly during the establishment year, emissions in subsequent years were over 50% higher in switchgrass than in corn, likely due to increased belowground biomass, which was over five times higher in switchgrass. Nitrate-N leaching decreased as the switchgrass stand matured, reaching 80% lower than in corn by the third year. Differences in ET and WUE between corn and switchgrass were not significant; however, results indicate a trend toward reduced WUE in switchgrass under drought, driven by lower aboveground biomass production. Our study demonstrates that switchgrass can be implemented at a commercial scale without negatively impacting the hydrological cycle, while potentially reducing N losses through nitrate-N leaching and soil N 2 O emissions, and enhancing belowground C storage.

09 BIOMASS FUELS↗
DOE OSTI2020

Effect of digestate and digestate supplemented with biochar on switchgrass growth and chemical composition

Digestate, a by-product of anaerobic digestion, can be an excellent source of nutrients for bioenergy crop production, while biochar, resulting from pyrolyzing biomass, can valorize the nutrients of digestate. The objective of this study was to evaluate the nutritional value of digestate and digestate + biochar for switchgrass production. The greenhouse experiment was conducted to determine the effects of a nitrogen (N) source including 0 N (control), urea (nutrient control), sewage sludge digestate, and sewage sludge digestate + corn stover biochar on switchgrass growth and feedstock composition. Nitrogen sources were observed to significantly increase plant weight at the 32-week harvest, with weight ranging from 94.2 to 125.2 g plant -1 , depending on the N source, compared to 70.7 g plant -1 from the negative control. Moreover, switchgrass treated with digestate + biochar showed higher plant weight than samples treated only with digestate. Nitrogen application of urea, digestate, and digestate + biochar had positive effects on plant height and total leaf area in the 32-week harvests and chlorophyll content in the 8-week harvests. Feedstock quality traits including hemicellulose, cellulose, and lignin content were not affected by N sources in either the 8 or 32-week harvests with the exception of ash concentration in the 32-week harvests. Our results indicate that digestate and digestate + biochar can be a potential substitute for chemical fertilizer, resulting in increased biomass yield.

09 BIOMASS FUELS↗
DOE OSTI2022

Effect of amine type on acidic toxic gas adsorption at ambient conditions on modified CuBTC

We report two amine-modified copper-based Metal Organic Frameworks (MOF (CuBTC)) of different surface chemical and textural features were synthesized and used as adsorbents of acidic toxic gases (NO 2 and H 2 S) in both moist (71% relative humidity (R.H.)) and dry conditions. The initial and exhausted samples were characterized by nitrogen adsorption, powder X-ray diffraction, scanning electron microscopy, thermal gravimetric analysis and Fourier transform infrared spectroscopy. The addition of melamine prevented full growth of CuBTC crystals and resulted in amorphous-like particles with sizes less than 200 nm. The material was non-porous with a small surface area. When urea was used as an amine source, the resulting particles maintained the overall octahedral shape of the parent CuBTC MOF and the material was more porous than the parent MOF. While the urea-modified CuBTC sample performed well as an NO 2 adsorbent in the presence of moisture, the reactivity of the melamine-modified sample and its physical properties provided a favorable environment for the removal of H 2 S. The incorporation of amines into the MOF structure also resulted in surface defects /open copper sites that favored the removal of toxic gases in dry conditions. The reactivity of the adsorbents with toxic gases was demonstrated by the changes in the adsorbent colors, in texture, and in surface chemistry (organic salts, complexes, sulfides and nitrates were formed).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Detecting Reactive Products in Carbon Capture Polymers with Chemical Shift Anisotropy and Machine Learning

Aminopolymers are attractive sorbents for CO 2 direct air capture applications due to their high density of amine groups, which can readily react with atmospheric levels of CO 2 to form chemisorbed species. The identity of these chemisorbed species and the functional groups that form upon oxidative degradation depends on both material properties and processing conditions, forming a variety of carbonyl-type sites such as ammonium carbamates, bicarbonates, carbonates, carbamic acids, ureas, and amides. 13 C solid-state nuclear magnetic resonance (NMR) is often used to help elucidate the identity of these reacted species, but it is challenging due to the narrow chemical shift range of carbonyl sites. Herein, we demonstrate the application of a two-dimensional (2D) chemical shift anisotropy (CSA) recoupling pulse sequence (ROCSA) to obtain CSA tensor values at each isotropic chemical shift, overcoming limitations of isotropic peak resolution. CSA tensor values describe the local chemical environment and can readily differentiate between the chemisorbed and degradation products. To aid identification, we also developed a k-nearest neighbor (kNN) classification model to distinguish the functional groups via their CSA tensor parameters. This methodology was demonstrated on poly(ethylenimine) in γ-Al 2 O 3 exposed to CO 2 and showed that the chemisorbed products are ammonium carbamate and a mixed carbamate–carbamic acid species. The sample was analyzed again after desorption at 100 °C inducing mild degradation, and the remaining products were strongly bound carbamate and urea species. In conclusion, the combination of 2D CSA measurements coupled with a kNN classification model enhances the ability to accurately identify chemisorbed or degradation products in complex carbon capture materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗