Search NASA⌕ Search

SEARCH · Search NASA

Results for “Vehicle modeling and simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

NLR's FleetDNA Speed Distributions for EPA MOVES

The U.S. Environmental Protection Agency (EPA) MOtor Vehicle Emission Simulator (MOVES) models mobile sources of air toxics at small and large scales across the Unites States. Vehicle speed distributions based on the type of vehicle, type of road traveled, and hour of the day are inputs into MOVES. In conjunction with vehicle miles traveled (VMT) inputs, they are used to estimate total operation time and select the relevant driving cycles from which running operating modes and emissions are estimated. In an ongoing research effort, the National Laboratory of the Rockies (NLR) partnered with the EPA to provide default average speed data for heavy-duty vehicles based on NLR's FleetDNA database and the Bourns College of Engineering - Center for Environmental Research and Technology (CE-CERT) data set from the University of California, Riverside.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1991

Dynamic response of a hammerhead launch vehicle wind-tunnel model

NASA-Langley has wind tunnel-tested an aeroelastically-scaled (1/10th-scale) Atlas-Centaur I Large Payload Fairing launch-vehicle model capable of simulating either of the first two bending vibration modes of the full-scale vehicle, on the basis of a partial-mode technique. While the primary emphasis was on the vehicle's buffet response, angle-of-attack studies were conducted for several payload fairing configurations with a view to both the buffet response and the dynamic stability of off-design conditions. No dynamic instabilities were discovered among the range of configurations, and payload fairing L/D variations were found to have only small buffet effects except for the smallest such value, in the second bending mode configuration.

Cole, Stanley R.↗
NASA NTRS2008

Practical Application of a Subscale Transport Aircraft for Flight Research in Control Upset and Failure Conditions

Over the past decade, the goal of reducing the fatal accident rate of large transport aircraft has resulted in research aimed at the problem of aircraft loss-of-control. Starting in 1999, the NASA Aviation Safety Program initiated research that included vehicle dynamics modeling, system health monitoring, and reconfigurable control systems focused on flight regimes beyond the normal flight envelope. In recent years, there has been an increased emphasis on adaptive control technologies for recovery from control upsets or failures including damage scenarios. As part of these efforts, NASA has developed the Airborne Subscale Transport Aircraft Research (AirSTAR) flight facility to allow flight research and validation, and system testing for flight regimes that are considered too risky for full-scale manned transport airplane testing. The AirSTAR facility utilizes dynamically-scaled vehicles that enable the application of subscale flight test results to full scale vehicles. This paper describes the modeling and simulation approach used for AirSTAR vehicles that supports the goals of efficient, low-cost and safe flight research in abnormal flight conditions. Modeling of aerodynamics, controls, and propulsion will be discussed as well as the application of simulation to flight control system development, test planning, risk mitigation, and flight research.

Cunningham, Kevin↗
NASA NTRS1976

Space shuttle lift-off dynamic model

Previously developed dynamic models for the calculation of lift-off dynamic response of the space shuttle vehicle can handle only response of the vehicle with eight holddown arms attached or with all holddown arms detached. The new model developed in the referenced report takes into account the transition period between holddown and lift-off by giving the model the ability to vary holddown point separation as a function of vehicle flexible body and rigid body motion. This report documents a study made to verify the new model's capability to simulate vehicle response at lift-off. To do this, a finite element model of the skirt is made and coupled to the free-free modes of the vehicle and cantilevered modes calculated and compared with the previously developed model. Results indicate that the new model will be able to predict accurate vehicle loads.

Christian, D.↗
NASA NTRS1977

A technique for simulating turbulence for aerospace vehicle flight simulation studies

An atmospheric turbulence model which accommodates variability of turbulence properties along an aerospace vehicle trajectory was developed. The technique involves the use of Dryden spectral forms in which the defining parameters are the standard deviations (sigma) and integral scales (L) of turbulence. These spectra are expressed as nondimensional functions of the nondimensional frequency Omega = omega L/V where omega is dimensional radian frequency and V is the true air speed of the aerospace vehicle. The nondimensional spectra are factored by standard techniques to obtain nondimensional linear recursive filters in the time domain whereby band-limited white-like noise can be operated upon to obtain nondimensional longitudinal, lateral, and vertical turbulence velocities, as functions of nondimensional time, tV/L, where t is time. Application of the technique to the simulation of the space shuttle orbiter entry flight phase is discussed.

Fichtl, G. H.↗
NASA NTRS2014

Guaranteed Road Network Search with Small Unmanned Aircraft

The use of teams of small unmanned aircraft in real-world rapid-response missions is fast becoming a reality. One such application is search and detection of an evader in urban areas. This paper draws on results in graph-based pursuit-evasion, developing mappings from these abstractions to primitive motions that may be performed by aircraft, to produce search strategies providing guaranteed capture of road-bound targets. The first such strategy is applicable to evaders of arbitrary speed and agility, offering a conservative solution that is insensitive to motion constraints pursuers may possess. This is built upon to generate two strategies for capture of targets having a known speed bound that require searcher teams of much smaller size. The efficacy of these algorithms is demonstrated by evaluation in extensive simulation using realistic vehicle models across a spectrum of environment classes.

unmanned aircraft systems↗
NASA NTRS1996

Simulation model of the F/A-18 high angle-of-attack research vehicle utilized for the design of advanced control laws

The 'f18harv' six degree-of-freedom nonlinear batch simulation used to support research in advanced control laws and flight dynamics issues as part of NASA's High Alpha Technology Program is described in this report. This simulation models an F/A-18 airplane modified to incorporate a multi-axis thrust-vectoring system for augmented pitch and yaw control power and actuated forebody strakes for enhanced aerodynamic yaw control power. The modified configuration is known as the High Alpha Research Vehicle (HARV). The 'f18harv' simulation was an outgrowth of the 'f18bas' simulation which modeled the basic F/A-18 with a preliminary version of a thrust-vectoring system designed for the HARV. The preliminary version consisted of two thrust-vectoring vanes per engine nozzle compared with the three vanes per engine actually employed on the F/A-18 HARV. The modeled flight envelope is extensive in that the aerodynamic database covers an angle-of-attack range of -10 degrees to +90 degrees, sideslip range of -20 degrees to +20 degrees, a Mach Number range between 0.0 and 2.0, and an altitude range between 0 and 60,000 feet.

Strickland, Mark E.↗
NASA NTRS2010

Demonstration of an Aerocapture GN and C System Through Hardware-in-the-Loop Simulations

Aerocapture is an orbit insertion maneuver in which a spacecraft flies through a planetary atmosphere one time using drag force to decelerate and effect a hyperbolic to elliptical orbit change. Aerocapture employs a feedback Guidance, Navigation, and Control (GN&C) system to deliver the spacecraft into a precise postatmospheric orbit despite the uncertainties inherent in planetary atmosphere knowledge, entry targeting and aerodynamic predictions. Only small amounts of propellant are required for attitude control and orbit adjustments, thereby providing mass savings of hundreds to thousands of kilograms over conventional all-propulsive techniques. The Analytic Predictor Corrector (APC) guidance algorithm has been developed to steer the vehicle through the aerocapture maneuver using bank angle control. Through funding provided by NASA's In-Space Propulsion Technology Program, the operation of an aerocapture GN&C system has been demonstrated in high-fidelity simulations that include real-time hardware in the loop, thus increasing the Technology Readiness Level (TRL) of aerocapture GN&C. First, a non-real-time (NRT), 6-DOF trajectory simulation was developed for the aerocapture trajectory. The simulation included vehicle dynamics, gravity model, atmosphere model, aerodynamics model, inertial measurement unit (IMU) model, attitude control thruster torque models, and GN&C algorithms (including the APC aerocapture guidance). The simulation used the vehicle and mission parameters from the ST-9 mission. A 2000 case Monte Carlo simulation was performed and results show an aerocapture success rate of greater than 99.7%, greater than 95% of total delta-V required for orbit insertion is provided by aerodynamic drag, and post-aerocapture orbit plane wedge angle error is less than 0.5 deg (3-sigma). Then a real-time (RT), 6-DOF simulation for the aerocapture trajectory was developed which demonstrated the guidance software executing on a flight-like computer, interfacing with a simulated IMU and simulated thrusters, with vehicle dynamics provided by an external simulator. Five cases from the NRT simulations were run in the RT simulation environment. The results compare well to those of the NRT simulation thus verifying the RT simulation configuration. The results of the above described simulations show the aerocapture maneuver using the APC algorithm can be accomplished reliably and the algorithm is now at TRL-6. Flight validation is the next step for aerocapture technology development.

Masciarelli, James↗
NASA NTRS2010

Modeling and Simulation of the ARES UPPER STAGE Transportation, Lifting, Stacking and Mating Operations Within the Vehicle Assembly Building at KSC

This viewgraph presentation describes the modeling and simulation of the Ares Upper Stage Transportation, lifting, stacking, and mating operations within the Vehicle Assembly Building (VAB) at Kennedy Space Center (KSC). An aerial view of KSC Launch Shuttle Complex, two views of the Delmia process control layout, and an upper stage move subroutine and breakdown are shown. An overhead image of the VAB and the turning basin along with the Pegasus barge at the turning basin are also shown. This viewgraph presentation also shows the actual design and the removal of the mid-section spring tensioners, the removal of the AFT rear and forward tensioners tie downs, and removing the AFT hold down post and mount. US leaving the Pegasus Barge, the upper stage arriving at transfer aisle, upper stage receiving/inspection in transfer aisle, and an overhead view of upper stage receiving/inspection in transfer aisle are depicted. Five views of the actual connection of the cabling to the upper stage aft lifting hardware are shown. The upper stage transporter forward connector, two views of the rotation horizontal to vertical, the disconnection of the rear bolt ring cabling, the lowering of the upper stage to the inspection stand, disconnection of the rear bolt ring from the upper stage, the lifting of the upper stage and inspection of AFT fange, and the transfer of upper stage in an integrated stack are shown. Six views of the mating of the upper stage to the first stage are depicted. The preparation, inspection, and removal of the forward dome are shown. The upper stage mated on the integrated stack and crawler is also shown. This presentation concludes with A Rapid Upper Limb Assessment (RULA) utilizing male and female models for assessing risk factors to the upper extremities of human beings in an actual physical environment.

Kromis, Phillip A.↗
NASA NTRS2004

Modeling and Simulation of Reliability & Maintainability Parameters for Reusable Launch Vehicles using Design of Experiments

This paper describes the development of a methodology for estimating reliability and maintainability distribution parameters for a reusable launch vehicle. A disciplinary analysis code and experimental designs are used to construct approximation models for performance characteristics. These models are then used in a simulation study to estimate performance characteristic distributions efficiently. The effectiveness and limitations of the developed methodology for launch vehicle operations simulations are also discussed.

Unal, Resit↗
NASA NTRS1979

Phase 1 of the near team hybrid passenger vehicle development program. Appendix C: Preliminary design data package. Volume 2: Appendices

The design, development, efficiency, manufacturability, production costs, life cycle cost, and safety of sodium-sulfur, nickel-zinc, and lead-acid batteries for electric hybrid vehicles are discussed. Models are given for simulating the vehicle handling quality, and for finding the value of: (1) the various magnetic quantities in the different sections in which the magnetic circuit of the DC electric machine is divided; (2) flux distribution in the air gap and the magnetization curve under load conditions; and (3) the mechanical power curves versus motor speed at different values of armature current.

Piccolo, R.↗
NASA NTRS2011

Modeling, Analysis and Simulation Approaches Used in Development of the National Aeronautics and Space Administration Max Launch Abort System

The National Aeronautics and Space Administration (NASA) Engineering and Safety Center was chartered to develop an alternate launch abort system (LAS) as risk mitigation for the Orion Project. Its successful flight test provided data for the design of future LAS vehicles. Design of the flight test vehicle (FTV) and pad abort trajectory relied heavily on modeling and simulation including computational fluid dynamics for vehicle aero modeling, 6-degree-of-freedom kinematics models for flight trajectory modeling, and 3-degree-of-freedom kinematics models for parachute force modeling. This paper highlights the simulation techniques and the interaction between the aerodynamics, flight mechanics, and aerodynamic decelerator disciplines during development of the Max Launch Abort System FTV.

Yuchnovicz, Daniel E.↗
NASA NTRSDate not supplied

3D Representation of UAV-obstacle Collision Risk under off-nominal conditions

Safe operations of autonomous unmanned aerial vehicles (UAVs) in low-altitude airspace with beyond visual line-of-sight (BVLOS) flights demand robust risk monitoring of airspace as well as of people and property on ground. One of the safety critical factors for UAV flights is the risk of collision with static and dynamic obstacles in proximity to its flight path. This paper presents a detailed formulation of risk likelihood of obstacle collision incorporating the effects of off-nominal conditions introduced by component failures, degraded controllability and environmental disturbances such as wind gusts. The deviation in the planned trajectory caused due to wind is computed utilizing a point-mass 3D kinematic simulation model of the vehicle. Likelihood of risk for the flight plan is then analyzed based on generating the probability of collision for each point in the trajectory. The proposed risk factor is demonstrated on real flight data from experimental flights of an octocopter at NASA Langley Research Center in presence of simulated obstacles and wind conditions. Effect of varying wind conditions, distance from obstacles, level of controllability and obstacle measurement noise on the risk factor is demonstrated. The proposed approach enables risk-informed decision making for timely mitigation of current and future unsafe events in autonomous systems.

Portia Banerjee↗
DOE OSTI2025

AutonomieAI: An efficient and deployable vehicle energy consumption estimation toolkit

Here, this paper presents AutonomieAI, a novel toolkit designed for efficient energy estimation of vehicles across diverse trip scenarios, routes, and drive cycles, applicable to a broad range of vehicle powertrain technologies. It leverages state-of-the-art Machine Learning techniques to deliver real-time energy prediction of vehicles, enabling co-simulation with transportation level system tools and opening doors for large-scale optimization at city, network or national level. Benchmark results show that AutonomieAI achieves high accuracy, with an average percentage error below 2% for most powertrain types, and computational efficiency capable of processing over 10,000 trips per second. Applications of AutonomieAI have potential to offer the flexibility to assist in solving eco-routing problems, optimize for vehicle and powertrain selection, study charging decision behavior, and optimize for charging station placement. AutonomieAI is the result of large neural network based model architectures, trained on very large and unique high fidelity vehicle simulation data. It is lightweight, deployable, efficient and has accuracy comparable to specialized and complex physics based simulation softwares.

Autonomie↗
DOE OSTI2022

EVI-Equity

EVI-Equity (Electric Vehicle Infrastructure for Equity) is a $200k project, started around in June of 2021, with a funding from the Vehicle Technologies Office (VTO). The motivation was to create a new analytical capability that can enable us to quantify and investigate equitable access to and distribution of existing and future deployment of PEVs and EVSEs in neighborhoods, cities, states, and the nation. EVI-Equity is a bottom-up equity-focused analysis model, built upon individual (synthetic) households, aggregated by census block groups. It consists of four core components - community engagement, environmental profiling, household expenditures, and network design. Although there are some commonalities, EVI-Equity is not a vehicle choice model, charging simulation model, or transportation demand model. EVI-Equity is rather a cross-cutting analysis tool, dedicated for evaluating equitable EV adoption and EVSE deployment, encompassing and bridging a wide variety of related tools, models, and frameworks. Some of the results indicate the importance of used vehicle market for low-income households. The presentation also highlights similarities and variations as to preferred public charging locations. For example, regardless of household income, retail spots are the most preferred location for public charging, followed by curbside/street. However, the results also imply that the importance of workplace charging may vary with income - the lower the income, the less important. Environmental profiling results, with an example of ground-level ozone in Atlanta area, show that the contrast between the haves and the have nots of plug-in electric vehicles depends on location. The assessment of household expenditures illustrates the economic impact of home charging access on an individual household level - the lower the income, the greater the impact is. Lastly, Denver metro area and the state of South Dakota are used to showcase the impact of different network design of charging infrastructure, as well as alternative (vs. baseline/existing) electric vehicle adoption pattern.

ADVANCED PROPULSION SYSTEMS,ENERGY PLANNING, POLIC↗
NASA NTRS2009

Real-Time Hardware-in-the-Loop Simulation of Ares I Launch Vehicle

The Ares Real-Time Environment for Modeling, Integration, and Simulation (ARTEMIS) has been developed for use by the Ares I launch vehicle System Integration Laboratory at the Marshall Space Flight Center. The primary purpose of the Ares System Integration Laboratory is to test the vehicle avionics hardware and software in a hardware - in-the-loop environment to certify that the integrated system is prepared for flight. ARTEMIS has been designed to be the real-time simulation backbone to stimulate all required Ares components for verification testing. ARTE_VIIS provides high -fidelity dynamics, actuator, and sensor models to simulate an accurate flight trajectory in order to ensure realistic test conditions. ARTEMIS has been designed to take advantage of the advances in underlying computational power now available to support hardware-in-the-loop testing to achieve real-time simulation with unprecedented model fidelity. A modular realtime design relying on a fully distributed computing architecture has been implemented.

Tobbe, Patrick↗
NASA NTRS2014

Benefits of a Unified LaSRS++ Simulation for NAS-Wide and High-Fidelity Modeling

The LaSRS++ high-fidelity vehicle simulation was extended in 2012 to support a NAS-wide simulation mode. Since the initial proof-of-concept, the LaSRS++ NAS-wide simulation is maturing into a research-ready tool. A primary benefit of this new capability is the consolidation of the two modeling paradigms under a single framework to save cost, facilitate iterative concept testing between the two tools, and to promote communication and model sharing between user communities at Langley. Specific benefits of each type of modeling are discussed along with the expected benefits of the unified framework. Current capability details of the LaSRS++ NAS-wide simulations are provided, including the visualization tool, live data interface, trajectory generators, terminal routing for arrivals and departures, maneuvering, re-routing, navigation, winds, and turbulence. The plan for future development is also described.

Glaab, Patricia↗
NASA NTRS2022

IRIS: High-fidelity Perception Sensor Modeling for Closed-Loop Planetary Simulations

Perception plays a key role in autonomous and semi-autonomous planetary exploration vehicles. For instance, landers can use computer vision techniques for identifying safe landing locations, aerial vehicles use cameras as navigation sensors, and planetary rovers use them for localization and hazard detection. Engineering simulations of such systems requires the accurate modeling of perception and vision sensors for simulating autonomy scenarios. In addition, the modeling of sensors for landers, aerial and ground vehicles requires the ability to handle large and high-resolution terrains, the accurate modeling of illumination, hi-fidelity rendering via ray/path tracing and the inclusion of sensor characteristics. Vision sensor models strive to simulate sensor reality by using physics principles to model the interaction of light and objects. Furthermore, high frame rate performance is highly desirable for in-the-loop simulations involving vehicle dynamics and control software. In this paper we describe a new sensor modeling capability called Inter-planetary Rendering for Imaging and Sensors (IRIS) that meets these requirements for the real-time and high-fidelity simulation of vision sensors for planetary aerospace and robotics applications.

Elmquist, Asher↗