Search NASA⌕ Search

SEARCH · Search NASA

Results for “Vortex lattices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

The numerical simulation of subsonic flutter

The present paper describes a numerical simulation of unsteady, subsonic aeroelastic responses. The technique accounts for aerodynamic nonlinearities associated with angles of attack, vortex-dominated flow, static deformations, and unsteady behavior. The fluid and the wing together are treated as a single dynamic system, and the equations of motion for the structure and flowfield are integrated simultaneously and interactively in the time domain. The method employs an iterative scheme based on a predictor-corrector technique. The aerodynamic loads are computed by the general unsteady vortex-lattice method and are determined simultaneously with the motion of the wing. Two models are used to demonstrate the technique: a rigid wing on an elastic support experiencing plunge and pitch about the elastic axis, and a continuous wing rigidly supported at the root chord experiencing spanwise bending and twisting. The time domain solution coupled with the unsteady vortex-lattice method provides the capability of graphically depicting wing and wake motion. Several graphs that illustrate the time domain behavior of the wing and wake are presented.

Strganac, Thomas W.↗
NASA NTRS2000

Model Validation of Wake-Vortex/Aircraft Encounters

Wake-vortex effects on an 10% scale model of the B737-100 aircraft are calculated using both strip theory and vortex-lattice methods. The results are then compared to data taken in the 30ft x 60ft wind tunnel at NASA Langley Research Center (LaRC). The accuracy of the models for a reduced geometry, such with the horizontal stabilizer and the vertical tail removed, is also investigated. Using a 10% error in the circulation strength and comparing the model's results with the experiment illustrates the sensitivity of the models to the vortex circulation strength. It was determined that both strip theory and the vortex lattice method give accurate results when all the geometrical information is used. When the horizontal stabilizer and vertical tail were removed there were difficulties modeling the sideforce coefficient and pitching moment. With the removal of only the vertical tail unacceptable errors occurred when modeling the sideforce coefficient and yawing moment. Lift could not be accurately modeled with either the full geometry or the reduced geometry.

Pete, Kimberly R.↗
NASA NTRS1984

Wind tunnel wall interference in closed, ventilated and adaptive test sections

A wall interference correction method for closed rectangular test sections was developed which uses measured wall pressures. Measurements with circular discs for blockage and a rectangular wing as a lift generator in a square closed test section validate this method. These measurements are intended to be a basis of comparison for measurements in the same tunnel using ventilated (in these case, slotted) walls. Using the vortex lattice method and homogeneous boundary conditions, calculations were performed which show sufficiently high pressure levels at the walls for correction purposes in test sections with porous walls. In Gottingen, an adaptive test section (which is a deformable rubber tube of 800 mm diameter) was built and a computer program was developed which is able to find the necessary wall adaptation for interference-free measurements in a single step. To check the program prior to the first run, the vortex lattice method was used to calculate wall pressure distributions in the nonadapted test section as input data for the one-step method. Comparison of the pressure distribution in the adapted test section with free-flight data shows nearly perfect agreement. An extension of the computer program can be made to evaluate the remaining interference corrections.

Holst, H.↗
NASA NTRS2015

Static Aeroelastic Modeling of a Sub-Scale Wind Tunnel Model with Novel Flap Concept

This paper examines the static aeroelastic modeling of a flexible wind tunnel model equipped with a novel control effector known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system. The wind tunnel model is an approximately 10 percent sub-scale version of a wing designed to be equipped on a commerical transport aircraft such as the full-scale NASA Generic Transport Model (GTM). The structure of the model is made highly flexible such that a 10 percent of semi-span wing tip deflection is expected at a design lift condition, and a representation of the VCCTEF concept is incorporated on the model. Static aeroelastic modeling is conducted by using a representative single beam structural finite-element model coupled to a vortex-lattice aerodynamic model. The resulting aeroelastic model of the flexible wind tunnel model is compared against experimental wind tunnel test results from the actual model tested at the University of Washington Aeronautical Laboratory (UWAL). Comparison cases are made using reference and VICON measurements of VCCTEF flap deflections from the wind tunnel test data, and percent errors between the lift curve parameters are presented. The results show up to a maximum percent of error of <10% with regards to lift curve slope values between the aeroelastic model and the UWAL test data. The agreement of lift curve slope values from the aeroelastic model and experimental test results serves as validation for the coupled vortex-lattice finite-element static aeroelastic model.

Aeroelasticity↗
DOE OSTI2024

Vortex phase diagram of the kagome superconductor CsV 3 ⁢Sb 5

The screening response of the kagome superconductor CsV 3 ⁢Sb 5 was obtained from high-resolution ac mutual inductance measurements. At zero applied magnetic field and low temperatures, we observe no evidence for gapless quasiparticles, while near T c we find evidence for enhanced fluctuations. A rich vortex state appears above H c⁢1 ≈30 Oe, exhibiting successive emergence of vortex phases. For a fixed magnetic field, lowering the temperature below T c⁡ (H) leads to a wide range of vortex liquid state in a landscape of weak pinning potential, which gives rise to an irreversibility line. Further lowering the temperature, we identify the vortex melting line followed by the peak effect manifested in enhanced vortex pinning strength and critical current. Finally, we suggest that such an unusual behavior, where the peak effect region is fully contained within the vortex lattice state below the irreversibility line, is a consequence of the strong anisotropy and weak bulk pinning in CsV 3 ⁢Sb 5 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1926

Lattice arrangements for rapid convergence

A simple, systematic, optimized vortex-lattice approach is developed for application to lifting-surface problems. It affords a significant reduction in computational costs when compared to current methods. Extensive numerical experiments have been carried out on a wide variety of configurations, including wings with camber and single or multiple flaps, as well as high-lift jetflap systems. Rapid convergence as the number of spanwise or chordwise lattices are increased is assured, along with accurate answers. The results from this model should be useful not only in preliminary aircraft design but also, for example, as input for wake vortex roll-up studies and transonic flow calculations.

Hough, G. R.↗
DOE OSTI2020

Mechanism for Anomalous Hall Ferromagnetism in Twisted Bilayer Graphene

Motivated by the recent observation of an anomalous Hall effect in twisted bilayer graphene, here we use a lowest Landau level model to understand the origin of the underlying symmetry-broken correlated state. This effective model is rooted in the occurrence of Chern bands which arise due to the coupling between the graphene device and its encapsulating substrate. Our model exhibits a phase transition from a spin-valley polarized insulator to a partial or fully valley unpolarized metal as the bandwidth is increased relative to the interaction strength, consistent with experimental observations. In sharp contrast to standard quantum Hall ferromagnetism, the Chern number structure of the flat bands precludes an instability to an intervalley coherent phase, but allows for an excitonic vortex lattice at large interaction anisotropy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1977

Rolling moments in a trailing vortex flow field

Pressure distributions are presented which were measured on a wing in close proximity to a tip vortex of known structure generated by a larger, upstream semispan wing. Overall loads calculated by integration of these pressures are checked by independent measurements made with an identical model mounted on a force balance. Several conventional methods of wing analysis are used to predict the loads on the following wing. Strip theory is shown to give uniformly poor results for loading distribution, although predictions of overall lift and rolling moment are sometimes acceptable. Good results are obtained for overall coefficients and loading distribution by using linearized pressures in vortex-lattice theory in conjunction with a rectilinear vortex. The equivalent relation from reverse-flow theory that can be used to give economic predictions for overall loads is presented.

Mcmillan, O. J.↗
NASA NTRS1977

Rolling moments in a trailing vortex flow field

Pressure distributions are presented which were measured on a wing in close proximity to a tip vortex of known structure generated by a larger, upstream semispan wing. Overall loads calculated by integration of these pressures are checked by independent measurements made with an identical model mounted on a force balance. Several conventional methods of wing analysis are used to predict the loads on the following wing. Strip theory is shown to give uniformly poor results for loading distribution, although predictions of overall lift and rolling moment are sometimes acceptable. Good results are obtained for overall coefficients and loading distribution by using linearized pressures in vortex-lattice theory in conjunction with a rectilinear vortex. The equivalent relation from reverse-flow theory that can be used to give economic predictions for overall loads is presented.

Mcmillan, O. J.↗
DOE OSTI2021

Campbell penetration depth in low carrier density superconductor YPtBi

Magnetic penetration depth, λ m , was measured as a function of temperature and magnetic field in single crystals of low carrier density superconductor YPtBi by using a tunnel-diode oscillator technique. Measurements in zero DC magnetic field yield London penetration depth, λ L ( T ) , but in the applied field the signal includes the Campbell penetration depth, λ C ( T ) , which is the characteristic length of the attenuation of small excitation field, H AC , into the Abrikosov vortex lattice due to its elasticity. Whereas the magnetic field dependent λ C exhibit λ C ~ B p with p = 1 / 2 in most of the conventional and unconventional superconductors, we found that p ≈ 0.23 << 1 / 2 in YPtBi due to rapid suppression of the pinning strength. From the measured λ C ( T , H ) , the critical current density is j c ≈ 40 A / cm 2 at 75 mK. We find that this is orders of magnitude lower than that of conventional superconductors of comparable T c .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1984

The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

Grantz, A. C.↗
NASA NTRS1989

Prediction of forces and moments for flight vehicle control effectors: Workplan

Two research activities directed at hypersonic vehicle configurations are currently underway. The first involves the validation of a number of classical local surface inclination methods commonly employed in preliminary design studies of hypersonic flight vehicles. Unlike studies aimed at validating such methods for predicting overall vehicle aerodynamics, this effort emphasizes validating the prediction of forces and moments for flight control studies. Specifically, several vehicle configurations for which experimental or flight-test data are available are being examined. By comparing the theoretical predictions with these data, the strengths and weaknesses of the local surface inclination methods can be ascertained and possible improvements suggested. The second research effort, of significance to control during take-off and landing of most proposed hypersonic vehicle configurations, is aimed at determining the change due to ground effect in control effectiveness of highly swept delta planforms. Central to this research is the development of a vortex-lattice computer program which incorporates an unforced trailing vortex sheet and an image ground plane. With this program, the change in pitching moment of the basic vehicle due to ground proximity, and whether or not there is sufficient control power available to trim, can be determined. In addition to the current work, two different research directions are suggested for future study. The first is aimed at developing an interactive computer program to assist the flight controls engineer in determining the forces and moments generated by different types of control effectors that might be used on hypersonic vehicles. The first phase of this work would deal in the subsonic portion of the flight envelope, while later efforts would explore the supersonic/hypersonic flight regimes. The second proposed research direction would explore methods for determining the aerodynamic trim drag of a generic hypersonic flight vehicle and ways in which it can be minimized through vehicle design and trajectory optimization.

Maughmer, Mark D.↗
NASA NTRS1975

A subvortex technique for the close approach to a discretized vortex sheet

The close-approach problem associated with flow calculation methods based on vortex-lattice theory was examined numerically using two-dimensional discretized vortex sheets. The analysis first yields a near-field radius of approximately the distance apart of the vortices in the lattice; only within this distance from the sheet are the errors arising from the discretization significant. Various modifications to the discrete vortices are then considered with the objective of reducing the errors. This leads to a near-field model in which a vortex splits into an increasing number of subvortices as it is approached. The subvortices, whose strengths vary linearly from the vortex position, are evenly distributed along an interpolated curve passing through the basic vortices. This subvortex technique can be extended to the three-dimensional case and is efficient because the number of vortices is effectively increased, but only where and when needed.

Maskew, B.↗
NASA NTRS1983

High angle-of-attack calculations of the subsonic vortex flow on slender bodies

A nonlinear vortex-lattice method is utilized for the calculation of separated vortex flows over slender bodies at high incidence. Symmetric and asymmetric vortex flow cases are calculated showing good agreement with recently obtained experimental data for an ogive-cyclinder body at high Reynolds numbers. The only input needed for these calculations is the positions of the separation lines on the body. Studies of some of the numerical aspects of this method are described and conclusions are implemented to improve the calculations.

Almosnino, D.↗
NASA NTRS1985

Lift due to thickness for low aspect ratio wings in incompressible flow

The problem under consideration is a numerical study of the effects of thickness on lift for low aspect ratio wings in steady incompressible inviscid flow at moderate angles of attack. At these angles of attack the flow separates along the leading edge giving rise to a lift substantially higher than that computed by classical attached flow potential theory. The problem is treated as a perturbation expansion in a small thickness parameter. The lifting elements of the flow are modeled using a nonlinear vortex lattice method which replaces the leading and trailing edge vortex sheets by segmented straight vortex filaments. The thickness elements of the flow are modeled with a mean plane source distribution and a modification to the wing boundary conditions. Results are obtained for wings with biconvex and NACA 0012 sections which compare well with available experimental data. The important observation that the effect of thickness is to decrease the lift is made.

Dodbele, S. S.↗
NASA NTRS1976

Scanning laser-velocimeter surveys and analysis of multiple vortex wakes of an aircraft

A laser velocimeter capable of rapidly scanning a flow field while simultaneously sensing two components of the velocity was used to measure the vertical and streamwise velocity structure 1.5 spans downstream in the wake of a model typical of a large subsonic transport (Boeing 747). This flow field was modeled by a superposition of axisymmetric vortices with finite cores. This theoretical model was found to agree with the measured velocities everywhere except where two vortices were in close proximity. Vortex strengths derived from the span loading on the wing as predicted by vortex-lattice theory also agree with the present measurements. The axisymmetric vortex model used herein is a useful tool for analytically investigating the vortex wakes of aircraft.

Corsiglia, V. R.↗
NASA NTRS1978

Research on the statically thrusting propeller

Methods for calculating the induced flow at propeller blades were analyzed by treating the wake formation as an initial problem in time. An unsteady vortex lattice technique was applied to the wake formation and the vortex core size was studied.

Eisenhuth, J. J.↗
NASA NTRS1987

Loss of lift due to thickness for low-aspect-ratio wings in incompressible flow

The problem under consideration is a numerical study of the effects of thickness on lift for low-aspect-ratio wings in steady incompressible inviscid flow at moderate angles of attack. At these angles of attack the flow separates along the leading edge giving rise to a lift substantially higher than that computed by classical attached-flow potential theory. The problem is treated as a perturbation expansion in a small thickness parameter. The lifting elements of the flow are modeled using a nonlinear vortex-lattice method which replaces the leading and trailing-edge vortex sheets by segmented straight vortex filaments. The thickness elements of the flow are modeled with a mean-plane source distribution and a modification to the wing boundary conditions. Results are obtained for wings with biconvex and NACA 0012 sections which compare well with available experimental data. The important observation that the effect of thickness is to decrease the lift is made.

Dodbele, S. S.↗