Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING BODY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Study of supersonic intersection flowfield at modified wing-body junctions

The problem of supersonic flow control using fillets and sweep for a wing-body junction has been investigated numerically using a three-dimensional Navier-Stokes code, which employs the MacCormack's time-split finite volume technique. An elliptic grid generation technique with direct control over spacing has been developed for constructing the grid at a filleted wing-body junction. The computed results for pressure distribution, particle paths, and limiting streamlines on the flat plate and fin surface for a swept fin show a decrease in the peak pressure on the fin leading edge and in the extent of the separated flow region. Moreover, the results for filleted juncture clearly show that the flow streamline patterns lose much of their vortical character with proper filleting. It has been demonstrated that fillets with a radius of three-and-one-half times the fin leading-edge diameter are required to weaken the vorticity in the horseshoe vortex by a factor of three for the Mach number and Reynolds number considered in the present study.

Lakshmanan, B.↗
NASA NTRS1986

Supersonic wing-body inteference at high angles of attack with emphasis on low aspect ratios

A systematic NASA data base for cruciform wing-body combinations has been analyzed to extract the values of the wing and body interference factors. The fin planforms vary in aspect ratio from 0.5 to 2.0, the Mach number from 2.5 to 4.5, and the angle of attack from 0 deg to 40 deg. Sufficient data are available to permit interpolation with respect to fin aspect ratio, taper ratio, Mach number, and angle of attack. The data base described in this paper can be used in an engineering prediction method to determine the normal force of planar wing-body combinations and for scaling the effects of body radius-fin semispan ratio.

Nielsen, J. N.↗
NASA NTRS1982

An analytical procedure for computing smooth transitions between two specified cross sections with applications to blended wing body configuration

An analytical procedure is described for designing smooth transition surfaces for blended wing-body configurations. Starting from two specified cross section shapes, the procedure generates a gradual transition from one cross section shape to the other as an analytic blend of the two shapes. The method utilizes a conformal mapping, with subsequent translation and scaling, to transform the specified and shapes to curves that can be combined more smoothly. A sample calculation is applied to a blended wing-body missile type configuration with a top mounted inlet.

Barger, R. L.↗
NASA NTRS2016

Overview of Low-Speed Aerodynamic Tests on a 5.75% Scale Blended-Wing-Body Twin Jet Configuration

The NASA Environmentally Responsible Aviation (ERA) Project sponsored a series of computational and experimental investigations of the propulsion and airframe integration issues associated with Hybrid-Wing-Body (HWB) or Blended-Wing-Body (BWB) configurations. NASA collaborated with Boeing Research and Technology (BR&T) to conduct this research on a new twin-engine Boeing BWB transport configuration. The experimental investigations involved a series of wind tunnel tests with a 5.75-percent scale model conducted in two low-speed wind tunnels. This testing focused on the basic aerodynamics of the configuration and selection of the leading edge Krueger slat position for takeoff and landing. This paper reviews the results and analysis of these low-speed wind tunnel tests.

Vicroy, Dan D.↗
NASA NTRS1996

Transonic Aerodynamic Characteristics of a Proposed Wing Body Reusable Launch Vehicle Concept

A proposed wing body reusable launch vehicle was tested in the Marshall Space Flight Center (MSFC) 14 x 14 inch trisonic wind tunnel during the winter of 1994. this test resulted in the vehicle's subsonic and transonic (Mach 03 to 1.96) longitudinal and lateral aerodynamic characteristics. The effects of control surface deflections on the basic vehicle aerodynamics including a body flap, elevons, ailerons, and tip fins are presented.

Springer, Anthony M.↗
NASA NTRS1996

Wing-Body Aeroelasticity on Parallel Computers

This article presents a procedure for computing the aeroelasticity of wing-body configurations on multiple-instruction, multiple-data parallel computers. In this procedure, fluids are modeled using Euler equations discretized by a finite difference method, and structures are modeled using finite element equations. The procedure is designed in such a way that each discipline can be developed and maintained independently by using a domain decomposition approach. A parallel integration scheme is used to compute aeroelastic responses by solving the coupled fluid and structural equations concurrently while keeping modularity of each discipline. The present procedure is validated by computing the aeroelastic response of a wing and comparing with experiment. Aeroelastic computations are illustrated for a high speed civil transport type wing-body configuration.

Guruswamy, Guru P.↗
NASA NTRS1999

Inlet Noise Reduction by Shielding for the Blended-Wing-Body Airplane

Noise shielding benefits associated with an advanced unconventional subsonic transport concept, the Blended-Wing-Body, were studied using a 4- percent scale, 3-engine nacelle model. The study was conducted in the Anechoic Noise Research Facility at NASA Langley Research Center. A high- frequency, wideband point source was placed inside the nacelles of the center engine and one of the side engines in order to simulate broadband engine noise. The sound field of the model was measured with a rotating microphone array that was moved to various stations along the model axis and with a fixed array of microphones that was erected behind the model. Ten rotating microphones were traversed a total of 22 degrees in 2-degree increments. Seven fixed microphones covered an arc that extended from a point in the exhaust exit plane of the center engine (and directly below its centerline) to a point 30 degrees above the jet centerline. While no attempt was made to simulate the noise emission characteristics of an aircraft engine, the model source was intended to radiate sound in a frequency range encompassing 1, 2, and 3 times the blade passage of a typical full-scale engine. In this study, the Blended-Wing-Body model was found to provide significant shielding of inlet noise. In particular, noise radiated downward into the forward sector was reduced by 20 to 25 dB overall in the full-scale frequencies from 2000 to 4000 Hz, decreasing to 10 dB or less at the lower frequencies. Also, it was observed that noise associated with the exhaust radiates into the sector directly below the model downstream to reduce shielding efficiency.

Clark, Lorenzo R.↗
NASA NTRS2016

Conceptual Design and Structural Optimization of NASA Environmentally Responsible Aviation (ERA) Hybrid Wing Body Aircraft

Simultaneously achieving the fuel consumption and noise reduction goals set forth by NASA's Environmentally Responsible Aviation (ERA) project requires innovative and unconventional aircraft concepts. In response, advanced hybrid wing body (HWB) aircraft concepts have been proposed and analyzed as a means of meeting these objectives. For the current study, several HWB concepts were analyzed using the Hybrid wing body Conceptual Design and structural optimization (HCDstruct) analysis code. HCDstruct is a medium-fidelity finite element based conceptual design and structural optimization tool developed to fill the critical analysis gap existing between lower order structural sizing approaches and detailed, often finite element based sizing methods for HWB aircraft concepts. Whereas prior versions of the tool used a half-model approach in building the representative finite element model, a full wing-tip-to-wing-tip modeling capability was recently added to HCDstruct, which alleviated the symmetry constraints at the model centerline in place of a free-flying model and allowed for more realistic center body, aft body, and wing loading and trim response. The latest version of HCDstruct was applied to two ERA reference cases, including the Boeing Open Rotor Engine Integration On an HWB (OREIO) concept and the Boeing ERA-0009H1 concept, and results agreed favorably with detailed Boeing design data and related Flight Optimization System (FLOPS) analyses. Following these benchmark cases, HCDstruct was used to size NASA's ERA HWB concepts and to perform a related scaling study.

Quinlan, Jesse R.↗
NASA NTRS1994

Wing-Body Aeroelasticity Using Finite-Difference Fluid/Finite-Element Structural Equations on Parallel Computers

In recent years significant advances have been made for parallel computers in both hardware and software. Now parallel computers have become viable tools in computational mechanics. Many application codes developed on conventional computers have been modified to benefit from parallel computers. Significant speedups in some areas have been achieved by parallel computations. For single-discipline use of both fluid dynamics and structural dynamics, computations have been made on wing-body configurations using parallel computers. However, only a limited amount of work has been completed in combining these two disciplines for multidisciplinary applications. The prime reason is the increased level of complication associated with a multidisciplinary approach. In this work, procedures to compute aeroelasticity on parallel computers using direct coupling of fluid and structural equations will be investigated for wing-body configurations. The parallel computer selected for computations is an Intel iPSC/860 computer which is a distributed-memory, multiple-instruction, multiple data (MIMD) computer with 128 processors. In this study, the computational efficiency issues of parallel integration of both fluid and structural equations will be investigated in detail. The fluid and structural domains will be modeled using finite-difference and finite-element approaches, respectively. Results from the parallel computer will be compared with those from the conventional computers using a single processor. This study will provide an efficient computational tool for the aeroelastic analysis of wing-body structures on MIMD type parallel computers.

Byun, Chansup↗
NASA NTRS1979

Aerodynamic characteristics at Mach numbers of 1.5, 1.8, and 2.0 of a blended wing-body configuration with and without integral canards

An exploratory, experimental, and theoretical investigation was made of a cambered, twisted, and blended wing-body concept with and without integral canard surfaces. Theoretical calculations of the static longitudinal and lateral aerodynamic characteristics of the wing-body configurations were compared with the characteristics obtained from tests of a model in the Langley Unitary Plan wind tunnel. Mach numbers of 1.5, 1.8, and 2.0 and a Reynolds number per meter of 6.56 million were used in the calculations and tests. Overall results suggest that planform selection is extremely important and that the supplemental application of new calculation techniques should provide a process for the design of supersonic wings in which spanwise distribution of upwash and leading-edge thrust might be rationally controlled and exploited.

Robins, A. W.↗
NASA NTRS1955

Quasi-cylindrical theory of wing-body interference at supersonic speeds and comparison with experiment

A theoretical method is presented for calculating the flow field about wing-body combinations employing bodies deviating only slightly in shape from a circular cylinder. The method is applied to the calculation of the pressure field acting between a circular cylindrical body and a rectangular wing. The case of zero body angle of attack and variable wing incidence is considered as well as the case of zero wing incidence and variable body angle of attack. An experiment was performed especially for the purpose of checking the calculative examples.

Nielsen, Jack N↗