Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING FLAPS, SPLIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

Effect of retractable-spoiler location on rolling- and yawing-moment coefficients

In this report are presented the results of wind-tunnel tests of retractable spoilers on the upper surface of a Clark Y wing, which have been made as part of an investigation of lateral control devices being conducted by the National Advisory Committee for Aeronautics. Spoilers with chords up to 15.0 percent of the wing chord were tested in several locations on a plain rectangular wing and in two locations on the same wing equipped with a 20.0 percent chord split flap down 60 degrees. Charts are given for four representative angles of attack from which values of rolling- and yawing-moment coefficients may be obtained for spoilers up to 15.0 percent chord located on the upper surface of a Clark Y wing. The tests showed that at low angles of attack practically the same rolling moments can be obtained with a given spoiler at any location back of 30.0 percent of the wing chord, while at high angles of attack there is a definite advantage in locating the spoiler at least as far forward as 30.0 percent of the chord. The yawing moments accompanying a given rolling moment increase positively as the spoiler location is moved forward from the trailing edge of the wing. It is concluded that the 30.0 percent chord location is probably the optimum provided that instantaneous response of the airplane to a control movement can be obtained.

Shortal, J A↗
NASA NTRS1944

Whirling Arm Tests on the Effect of Ground Proximity to an Airplane Wing

This report gives the results of tests on a rectangular wing model with a 20% full spun split flap, conducted on the whirling arm at the Daniel Guggenheim Airship Institute in Akron, Ohio. The effect of a ground board on the lift and pitching moment was measured. The ground board consisted of an inclined ramp rising up in the test channel to a level floor extending for some distance parallel to the model path. The path of the wing model with respect to the ground board accordingly represented with comparative exactness an airplane coming in for a landing. The ground clearances over the level portion of the board varied from 0 6 to 1,6 chord lengths. Results are given in the standard dimensionless coefficients plotted versus angle of attack for a particular ground clearance. The effect of the ground board is to increase the lift coefficient for a given angle of attack all the way up the stall. The magnitude of the increase varies both with the ground clearance and the angle of attack. The effect on the pitching moment coefficient is not so readily apparent due to experimental difficulties but, in general, the diving moment increases over the ground board. This effect is apparent principally at the high angles of attack. An exception to this effect occurs with flaps deflected at the lowest ground clearance (0.6 chords). Here the diving moment decreases over the ground board.

Long, M. E.↗
NASA NTRS1937

Wind-tunnel tests of a Clark Y wing with 'Maxwell' leading-edge slots

Aerodynamic force tests of a Clark Y wing equipped with "Maxwell" type leading-edge slots were conducted in the N.A.C.A. 7- by 10-foot tunnel to ascertain the aerodynamic characteristics, which involved the determination of the best slot-gap opening, the effects of slat width, and the effect of a trailing-edge flap. The Maxwell wing with a wide-chord slat (0.30 c(sub w)) and with a 0.211 c(sub w) split flap deflected 60 degrees had a C(sub L sub max) of 2.53 or about twice that of the plain wing. The wing with the wide slat also had, in general, improved aerodynamic characteristics over those of the Maxwell wing with slat, and had about the same aerodynamic characteristics as a Handley Page slotted wing with approximately the same size of slat.

Gauvain, William E↗
NASA NTRS1941

Characteristics of NACA 4400R Series Rectangular and Tapered Airfoils, Including the Effect of Split Flaps

At the request of the Bureau of Aeronautics, Navy Department, tests were made in the variable-density wind tunnel of a tapered wing of 3-10-18 plan form and based on the NACA 4400R series sections. The wing was also tested with 0.2 chord spit flaps, deflected 60 deg span ratios of 0.3, 0.5, 0.7 and 1.0 respectively. In order to get data from which to calculate the characteristics of the flapped wing, the investigation was extended to include tests of the four rectangular airfoils of the NACA 4400R series (4409R, 4412R, 4415R, and 4418R) with full-span 0.2 chord, trailing edge split flaps deflected 60 deg.

Greenberg, Harry↗
NASA NTRS1948

Longitudinal-stability Investigation of High-lift and Stall-control Devices on a 52 Degree Sweptback Wing with and Without Fuselage and Horizontal Tail at a Reynolds Number of 6.8 x 10(exp 6).

Contains low-speed longitudinal stability characteristics of a 52 degree sweptback wing of aspect ratio 2.88, taper ratio 0.625, and NACA 64 (sub 1)-112 airfoil sections normal to the 0.282-chord line, in combination with split flaps, leading-edge flaps, and upper-surface fences. Low-wing and midwing-fuselage aerodynamic characteristics are presented with and without a horizontal tail at various vertical locations. Tests were conducted at a Reynolds number of 6.8 x 10(exp 6).

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS1978

Flap survey test of a combined surface blowing model: Flow measurements at static flow conditions

The Combined Surface Blowing (CSB) V/STOL lift/propulsion system consists of a blown flap system which deflects the exhaust from a turbojet engine over a system of flaps deployed at the trailing edge of the wing. Flow measurements consisting of velocity measurements using split film probes and total measure surveys using a miniature Kiel probe were made at control stations along the flap systems at two spanwise stations, the centerline of the nozzle and 60 percent of the nozzle span outboard of the centerline. Surface pressure measurements were made in the wing cove and the upper surface of the first flap element. The test showed a significant flow separation in the wing cove. The extent of the separation is so large that the flow into the first flap takes place only at the leading edge of the flap. The velocity profile measurements indicate that large spanwise (3 dimensional) flow may exist.

Fukushima, T.↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and of Several High-lift Devices on the Aerodynamic Characteristics in Yaw of a 47.5 Degree Sweptback

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5 and the airfoil sections normal to the quarter-chord line were NACA 61(sub 1)-A112. Tests included the plain wing and the wing with various combinations of extensible leading-edge and split flaps. The investigation was made to determine the effect of boundary-layer control by suction on the aerodynamic characteristics in yaw and on the effectiveness of a split-flap-type aileron for a range of angle of attack and suction-flow coefficient at a Reynolds number of 4.2 x 10 (exp 6) corresponding to a Mach number of approximately 0.07.

BOUNDARY LAYER - COMPLETE WINGS↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1947

An Investigation of the Low-speed Stability and Control Characteristics of Swept-forward and Swept-back Wing in the Ames 40- by 80-foot Wind Tunnel

An investigation has been made at large scale of the characteristics of highly swept wings. Data were obtained at several angles of sideslip on wings having angles of sweep of plus or minus 45 degrees, plus or minus 30 degrees, and 0 degrees. The airfoil sections of the wings varied from approximately NACA 0015 at the root to NACA 23009 at the tip. Each wing was investigated with flaps under flection, partial-span split flaps deflected 60 degrees, full-span split flaps defected 60 degrees and split-flap-type ailerons deflected plus or minus 15 degrees. Values of maximum lift were obtained at Reynolds numbers raging from 5.7 to 9.2 times 10 to the 6th power. In this report the summarized results are compared with the predictions made by use of the simplified theory for the effect of sweep and with existing small-scale data. The basic wind-tunnel results from which these summary data were taken are included in an appendix. The primary problems accompanying the use of weep as revealed by this investigation are the loss in maximum lift, the high effective dihedral, and the sharp reduction in lateral-control effectiveness. In general, simple theory enables good predictions to be made of the gross effects of sweep but further refinements are necessary to obtain the accuracy required for design purposes. In cases where comparisons can be made, the indications are that, as sweep increases, scale effects diminish and large-scale results approach small-scale results.

Mccormack, Gerald M↗
NASA NTRS1939

Wind-tunnel investigation of NACA 23012, 23021, and 23030 airfoils with various sizes of split flap

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of large-chord NACA and 23021, and 23030 airfoils with split flaps 10, 20, 30, and 40 percent of the wing chord to determine the section aerodynamic characteristics of the airfoils as affected by airfoil thickness, flap chord, and flap deflection. The complete section aerodynamic characteristics of all the combinations tested are given in the form of graphs of lift, drag, and pitching-moment coefficients, and certain applications to aerodynamic design are discussed.

Wenzinger, Carl J↗
NASA NTRS1939

Wind-tunnel Investigation of Effect of Yaw on Lateral-stability Characteristics I : Four N.A.C.A. 23012 Wings of Various Plan Forms with and Without Dihedral

Four N.A.C.A. 23012 wings were tested at several angles of yaw in the N.A.C.A. 7- by 10-foot wind tunnel. All the wings have rounded tips and, in plan form, one is rectangular and the others are tapered 3:1 with various amounts of sweep. Each wing was tested with two amounts of dihedral and with partial-span split flaps. The coefficients of lift, drag, and pitching moment are given for all the models at zero yaw. The coefficients of rolling moment, yawing moment, and side force are given for the rectangular wing at all values of yaw tested. The rate of change in the coefficients with angle of yaw is given in convenient form for stability calculations.

Bamber, M J↗
NASA NTRS1948

An Investigation of the Wing and the Wing-Fuselage Combination of a Full-Scale Model of the Republic XP-91 Airplane in the Ames 40-by 80-Foot Wing Tunnel

Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll af the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device, The maximum lift coefficient of the model with split flaps and the original partial-span straight slats was only 1.2; whereas a value of approximately 1.8 was obtained by drooping the slat and extending it full span, Improvement in maximum lift of approximately the same amount resulted when a full-span nose flap was substituted for the original partial-span slat.

Hunton, Lynn W.↗
NASA NTRS1942

Preliminary Wind-Tunnel Tests of the Effect of Nacelles on the Characteristics of a Twin-Engine Bomber Model with Low-Drag Wing, Special Report

Tests were made in the NACA 19-foot pressure tunnel of a simplified twin-engine bomber model with an NACA low-drag wing primarily to obtain an indication of the effects of engine nacelles on the characteristics of the model both with and without simple split trailing-edge flaps. Nacelles with conventional-type cowlings representative of those used on an existing high-performance airplane and with NACA high-speed type E cowlings were tested. The tests were made without propeller slipstream. The aerodynamic effects of adding the nacelles to the low-drag wing were similar to the effects commonly obtained by adding similar nacelles to conventional wings. The maximum lift coefficient without flaps was slightly increased, but the increment in maximum lift due to deflecting the flaps was somewhat decreased. The stalling characteristics were improved by the presence of the nacelles. Addition of the nacelles had a destabilizing effect on the pitching moments, as is usual for nacelles that project forward of the wing. The drag increments due to the nacelles were of the usual order of magnitude, with the increment due to the nacelles with NACA type E cowlings approximately one-third less than that of the nacelles with conventional cowlings with built-in air scoops.

Wenzinger, Carl J.↗
NASA NTRS1998

Atmospheric Probe Model: Construction and Wind Tunnel Tests

The material contained in this document represents a summary of the results of a low speed wind tunnel test program to determine the performance of an atmospheric probe at low speed. The probe configuration tested consists of a 2/3 scale model constructed from a combination of hard maple wood and aluminum stock. The model design includes approximately 130 surface static pressure taps. Additional hardware incorporated in the baseline model provides a mechanism for simulating external and internal trailing edge split flaps for probe flow control. Test matrix parameters include probe side slip angle, external/internal split flap deflection angle, and trip strip applications. Test output database includes surface pressure distributions on both inner and outer annular wings and probe center line velocity distributions from forward probe to aft probe locations.

Vogel, Jerald M.↗
NASA NTRS1973

Aerodynamic characteristics of a large-scale model with a swept wing and a jet flap having an expandable duct

The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.

Aiken, T. N.↗