Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING STALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Low-Reynolds Number Aerodynamics of an 8.9 Percent Scale Semispan Swept Wing for Assessment of Icing Effects

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing and computational flow simulations were carried out for an 8.9%-scale semispan wing based upon the Common Research Model airplane configuration. The wind-tunnel testing was conducted at the Wichita State University 7 ft x 10 ft Beech wind tunnel from Reynolds numbers of 0.8×10(exp 6) to 2.4×10(exp 6) and corresponding Mach numbers of 0.09 to 0.27. This paper presents the results of initial studies investigating the model mounting configuration, clean-wing aerodynamics and effects of artificial ice roughness. Four different model mounting configurations were considered and a circular splitter plate combined with a streamlined shroud was selected as the baseline geometry for the remainder of the experiments and computational simulations. A detailed study of the clean-wing aerodynamics and stall characteristics was made. In all cases, the flow over the outboard sections of the wing separated as the wing stalled with the inboard sections near the root maintaining attached flow. Computational flow simulations were carried out with the ONERA elsA software that solves the compressible, three-dimensional RANS equations. The computations were carried out in either fully turbulent mode or with natural transition. Better agreement between the experimental and computational results was obtained when considering computations with free transition compared to turbulent solutions. These results indicate that experimental evolution of the clean wing performance coefficients were due to the effect of three-dimensional transition location and that this must be taken into account for future data analysis. This research also confirmed that artificial ice roughness created with rapid-prototype manufacturing methods can generate aerodynamic performance effects comparable to grit roughness of equivalent size when proper care is exercised in design and installation. The conclusions of this combined experimental and computational study contributed directly to the successful implementation of follow-on test campaigns with numerous artificial ice-shape configurations for this 8.9% scale model.

Aerodynamics↗
NASA NTRS1976

Reduction of Stall-Spin Entry Tendencies Through Wing Aerodynamic Design

Results of recent wind tunnel tests and analyses are described which are aimed at helping to prevent spin entry after a stall by modifications to the aircraft wing. Simple add-on devices were utilized which modify the shape of the lift curve after stall, making it essentially flat to 30- 40 degree angle of attack. It is hypothesized that his will greatly reduce the danger of spin entry. Further research will be aimed at laying a firmer theoretical and analytical basis for the approach and at incorporating the complete full scale airplane and its dynamics into the problem.

Kroeger, R. A.↗
NASA NTRS1982

Some observations of separated flow on finite wings

Wind tunnel test results for aspects of flow over airfoils exhibiting single and multiple trailing edge stall 'mushroom' cells are reported. Rectangular wings with aspect ratios of 4.0 and 9.0 were tested at Reynolds numbers of 480,000 and 257,000, respectively. Surface flow patterns were visualized by means of a fluorescent oil flow technique, separated flow was observed with a tuft wand and a water probe, spanwise flow was studied with hot-wire anemometry, smoke flow and an Ar laser illuminated the centerplane flow, and photographs were made of the oil flow patterns. Swirl patterns on partially and fully stalled wings suggested vortex flow attachments in those regions, and a saddle point on the fully stalled AR=4.0 wing indicated a secondary vortex flow at the forward region of the separation bubble. The separation wake decayed downstream, while the tip vortex interacted with the separation bubble on the fully stalled wing. Three mushroom cells were observed on the AR=9.0 wing.

Winkelmann, A. E.↗
NASA NTRS1975

Prediction of span loading of straight-wing/propeller combinations up to stall

A method is presented for calculating the spanwise lift distribution on straight-wing/propeller combinations. The method combines a modified form of the Prandtl wing theory with a realistic representation of the propeller slipstream distribution. The slipstream analysis permits calculations of the nonuniform axial and rotational slipstream velocity field of propeller/nacelle combinations. This nonuniform field was then used to calculate the wing lift distribution by means of the modified Prandtl wing theory. The theory was developed for any number of nonoverlapping propellers, on a wing with partial or full-span flaps, and is applicable throughout an aspect ratio range from 2.0 and higher. A computer program was used to calculate slipstream characteristics and wing span load distributions for a number of configurations for which experimental data are available, and favorable comparisons are demonstrated between the theoretical predictions and the existing data.

Mcveigh, M. A.↗
NASA NTRS1992

Exploratory investigation of a spanwise blowing concept for tip-stall control on cranked-arrow wings

A novel blowing concept aimed at controlling the tip-panel stall of 'cranked-arrow' type wings was experimentally investigated. A spanwise-directed jet sheet tangential to the upper surface, blown from a chordwise slot located at the crank, interacts obliquely with the external flow to generate a powerful and highly controllable vortex, substantially covering the tip panel. The incremental suction due to this jet vortex, coupled with its flow stabilization effect improves the tip-panel maximum lift and stall characteristics, leading to pitch-up alleviation and lateral control augmentation. Low-speed wind tunnel flow visualizations, pressure measurements and force/moment results are presented validating the flow-control concept and illustrating its potential on a generic crank-arrow wing model.

Rao, Dhanvada M.↗
NASA NTRS1974

Effect of inlet ingestion of a wing tip vortex on turbojet stall margin

A two-dimensional inlet and a turbojet engine were investigated in a Mach 0.4 stream so as to ingest the tip vortex of a forward mounted wing. Results show that ingestion of a wing tip vortex by a turbojet engine can cause a large reduction in engine stall margin. The loss in stall compressor pressure ratio was primarily dependent on vortex location and rotational direction and not on total-pressure variations across the compressor face.

Mitchell, G. A.↗
NASA NTRS1977

Aerodynamic characteristics of wing-body configuration with two advanced general aviation airfoil sections and simple flap systems

Aerodynamic characteristics of a general aviation wing equipped with NACA 65 sub 2-415, NASA GA(W)-1, and NASA GA(PC)-1 airfoil sections were examined. The NASA GA(W)-1 wing was equipped with plain, split, and slotted partial- and full-span flaps and ailerons. The NASA GA(PC)-1 wing was equipped with plain, partial- and full-span flaps. Experimental chordwise static-pressure distribution and wake drag measurements were obtained for the NASA GA(PC)-1 wing at the 22.5-percent spanwise station. Comparisons were made between the three wing configurations to evaluate the wing performance, stall, and maximum lift capabilities. The results of this investigation indicated that the NASA GA(W)-1 wing had a higher maximum lift capability and almost equivalent drag values compared with both the NACA 65 sub 2-415 and NASA GA(PC)-1 wings. The NASA GA(W)-1 had a maximum lift coefficient of 1.32 with 0 deg flap deflection, and 1.78 with 41.6 deg deflection of the partial-span slotted flap. The effectiveness of the NASA GA(W)-1 plain and slotted ailerons with differential deflections were equivalent. The NASA GA(PC)-1 wing with full-span flaps deflected 0 deg for the design climb configuration showed improved lift and drag performance over the cruise flap setting of -10 deg.

Morgan, H. L., Jr.↗
NASA NTRS1978

Application of the laser velocimeter to airfoil research

A laser velocimeter (LV) was installed in the Langley V/STOL tunnel to measure the velocity field about a wing with a NACA 0012 airfoil section. These measurements were compared at low angle of attack with a two dimensional, viscous flow prediction program. The velocity field over the wing in a fully stalled condition was also measured by the LV. The unique ability of the LV to measure absolute flow magnitude and direction without prior knowledge of general flow direction was demonstrated in the complex separated reverse flows near the wing upper surface at the high angle of attack. The general characteristics of the flow field over the stalled wing were substantiated by a vapor screen flow visualization technique.

Hoad, D. R.↗
NASA NTRS1945

Summary of Measurements in Langley Full-Scale Tunnel of Maximum Lift Coefficients and Stalling Characteristics of Airplanes

The results of measurements in the Langley full-scale tunnel of the maximum lift coefficients and stalling characteristics of airplanes have been collected. The data have been analyzed to show the nature of the effects on maximum lift and stall of wing geometry, fuselages and nacelles, propeller slipstream, surface roughness, and wing leading-edge appendages such as ducts, armaments, tip slats, and airspeed heads. Comparisons of full-scale-tunnel and flight measurements of maximum lift and stall are included in some cases, and the effects of the different testing techniques on the maximum-lift measurements are also given.

Sweberg, Harold H↗
NASA NTRS1945

Determination of the Stability and Control Characteristics of a Tailless All-Wing Airplane Model with Sweepback in the Langley Free-Flight Tunnel

Force and flight tests were performance on an all-wing model with windmilling propellers. Tests were conducted with deflected and retracted flaps, with and without auxiliary vertical tail surfaces, and with different centers of gravity and trim coefficients. Results indicate serious reduction of stick-fixed longitudinal stability because of wing-tip stalling at high lift coefficient. Directional stability without vertical tail is undesirably low. Low effective dihedral should be maintained. Elevator and rudder control system is satisfactory.

WING FLAPS - DEFLECTION↗
NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in realtime, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗
NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in real-time, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real-time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗
NASA NTRS1938

NACA Stall-Warning Indicator

The stall-warning indicator employs a total-head tube located close to the wing surface in a region wherein local stalling occurs before the main portion of the wing stalls. The artificial production of a localized stalled region is accomplished by means of a sharp leading edge extending a few inches along the span. An abrupt drop in the total pressure relative to a static reference taken at some convenient point occurs at the stall in this region. Thin drop in total pressure caused the contraction of a pressure cell to which the total-head tube and the static orifice are connected and closed an electrical circuit that actuates a warning signal.

Thopmson, F L↗
NASA NTRS1972

Dynamic stability test results on an 0.024 scale B-1 air vehicle

Dynamic longitudinal and lateral-directional stability characteristics of the B-1 air vehicle were investigated in three wind tunnels at the Langley Research Center. The main rotary derivatives were obtained for an angle of attack range of -3 degrees to +16 degrees for a Mach number range of 0.2 to 2.16. Damping in roll data could not be obtained at the supersonic Mach numbers. The Langley 7 x 10 foot high speed tunnel, the 8 foot transonic pressure tunnel, and the 4 foot Unitary Plan wind tunnel were the test sites. An 0.024 scale light-weight model was used on a forced oscillation type balance. Test Reynolds number varied from 474,000/ft to 1,550,000/ft. through the Mach number range tested. The results showed that the dynamic stability characteristics of the model in pitch and roll were generally satisfactory up to an angle attack of about +6 degrees. In the wing sweep range from 15 to 25 degrees the positive damping levels in roll deteriorated rapidly above +2 degrees angle of attack. This reduction in roll damping is believed to be due to the onset of separation over the wing as stall is approached.

Beeman, R. R.↗
NASA NTRS1992

A LEX blowing technique for post-stall lateral control of trapezoidal wings

An exploratory low-speed wind-tunnel investigation of a pneumatic technique for LEX-induced lift augmetation on a low-aspect-ratio trapezoidal wing near C sub L, MAX is reported. The technique involved lateral sheet ejection from LEX edge-slots, with emphasis on nonsymmetrical blowing to obtain incremental roll control at high angles of attack when the aileron power is declining. Preliminary experiments on a pressure instrumented semispan wing model followed by force/moment measurements on a full-span LEX-wing configuration confirmed the effectiveness of LEX blowing for lateral control improvement up to an angle of attack of 45 deg and with a momentum coefficient of less than 02.

Rao, Dhanvada M.↗