Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, TRAPEZOIDAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Effects of Canard Planform and Wing-Leading-Edge Modification on Low-Speed Longitudinal Aerodynamic Characteristics of a Canard Airplane Configuration

An investigation has been conducted at low subsonic speeds to study the effects of canard planform and wing-leading-edge modification on the longitudinal aerodynamic characteristics of a general research canard airplane configuration. The basic wing of the model had a trapezoidal planform, an aspect ratio of 3.0, a taper ratio of 0.143, and an unswept 80-percent-chord line. Modifications to the wing included addition of full-span and partial-span leading-edge chord-extensions. Two canard planforms were employed in the study; one was a 60 deg sweptback delta planform and the other was a trapezoidal planform similar to that of the basic wing. Modifications to these canards included addition of a full-span leading-edge chord-extension to the trapezoidal planform and a fence to the delta planform. For the basic-wing-trapezoidal-canard configuration, rather abrupt increases in stability occurred at about 12 deg angle of attack. A slight pitch-up tendency occurred for the delta-canard configuration at approximately 8 deg angle of attack. A comparison of the longitudinal control effectiveness for the basic-wing-trapezoidal-canard combination and for the basic-wing-delta-canard combination indicates higher values of control effectiveness at law angles of attack for the trapezoidal canard. The control effectiveness for the delta-canard configuration, however, is seen to hold up for higher canard deflections and to higher angles of attack. Use of a full-span chord-extension deflected approximately 30 deg on the trapezoidal canard greatly improved the control characteristics of this configuration and enabled a sizeable increase in trim lift to be realized.

Spencer, Bernard, Jr.↗
NASA NTRS1986

Equivalent plate analysis of aircraft wing box structures with general planform geometry

A new equilvalent plate analysis formulation is described which is capable of modeling aircraft wing structures with a general planform such as cranked wing boxes. Multiple trapezoidal segments are used to represent such planforms. A Ritz solution technique is used in conjunction with global displacement functions which encompass all the segments. This Ritz solution procedure is implemented efficiently into a computer program so that it can be used by rigorous optimization algorithms for application in early preliminary design. A direct method to interface this structural analysis procedure with aerodynamic programs for use in aeroelastic calculations is described. This equivalent plate analysis procedure is used to calculate the static deflections and stresses and vibration frequencies and modes of an example wing configuration. The numerical results are compared with results from a finite element model of the same configuration to illustrate typical levels of accuracy and computation times resulting from use of this procedure.

Giles, G. L.↗
NASA NTRS1986

Equivalent plate analysis of aircraft wing box structures with general planform geometry

A new equivalent plate analysis formulation is described which is capable of modeling aircraft wing structures with a general planform such as cranked wing boxes. Multiple trapezoidal segments are used to represent such planforms. A Ritz solution technique is used in conjunction with global displacement functions which encompass all the segments. This Ritz solution procedure is implemented efficiently into a computer program so that it can be used by rigorous optimization algorithms for application in early preliminary design. A direct method to interface this structural analysis procedure with aerodynamic programs for use in aeroelastic calculations is described. This equivalent plate analysis procedure is used to calculate the static deflections and stresses and vibration frequencies and modes of an example wing configuration. The numerical results are compared with results from a finite element model of the same configuration to illustrate typical levels of accuracy and computation times resulting from use of this procedure.

Giles, G. L.↗
NASA NTRS1983

Status review of a supersonically-biased fighter wing-design study

Results from an ongoing supersonically-biased fighter wing-design study are summarized. The study has been conducted to explore the effects of supersonic aerodynamic performance, transonic maneuvering, low-speed/high angle-of-attack characteristics, and airframe system integration requirements on fighter aircraft wing design. The approach adopted involves the theoretical and experimental investigation of four advanced aircraft configurations which differ only in wing geometry. Supersonic and low-speed/high angle-of-attack wind tunnel results have been obtained for 20 deg trapezoidal, 65 deg delta, 70/30-deg advanced cranked, and 70/66-deg advanced cranked wing configurations. The supersonic data show that the advanced cranked wings outperform the trapezoidal and delta wings at cruise and moderate lift conditions. Low-speed/high angle-of-attack results show that all wings have significant stability problems above an angle of attack of 20 deg. Aircraft sizing analysis results show that the advanced cranked-wing configurations are significantly lighter, based upon take-off gross weight, than either the trapezoidal or the delta wings.

Wood, R. M.↗
NASA NTRS1983

Some lessons from NACA/NASA aerodynamic studies following World War II

An historical account is presented of the new departures in aerodynamic research conducted by NACA, and subsequently NASA, as a result of novel aircraft technologies and operational regimes encountered in the course of the Second World War. The invention and initial development of the turbojet engine furnished the basis for a new speed/altitude regime in which numerous aerodynamic design problems arose. These included compressibility effects near the speed of sound, with attendant lift/drag efficiency reductions and longitudinal stability enhancements that were accompanied by a directional stability reduction. Major research initiatives were mounted in the investigation of swept, delta, trapezoidal and variable sweep wing configurations, sometimes conducted through flight testing of the 'X-series' aircraft. Attention is also given to the development of the first generation of supersonic fighter aircraft.

Spearman, M. L.↗
NASA NTRS2000

Efficient Analysis of Complex Structures

Last various accomplishments achieved during this project are : (1) A Survey of Neural Network (NN) applications using MATLAB NN Toolbox on structural engineering especially on equivalent continuum models (Appendix A). (2) Application of NN and GAs to simulate and synthesize substructures: 1-D and 2-D beam problems (Appendix B). (3) Development of an equivalent plate-model analysis method (EPA) for static and vibration analysis of general trapezoidal built-up wing structures composed of skins, spars and ribs. Calculation of all sorts of test cases and comparison with measurements or FEA results. (Appendix C). (4) Basic work on using second order sensitivities on simulating wing modal response, discussion of sensitivity evaluation approaches, and some results (Appendix D). (5) Establishing a general methodology of simulating the modal responses by direct application of NN and by sensitivity techniques, in a design space composed of a number of design points. Comparison is made through examples using these two methods (Appendix E). (6) Establishing a general methodology of efficient analysis of complex wing structures by indirect application of NN: the NN-aided Equivalent Plate Analysis. Training of the Neural Networks for this purpose in several cases of design spaces, which can be applicable for actual design of complex wings (Appendix F).

Kapania, Rakesh K.↗
NASA NTRS1977

Reynolds number effects on the aerodynamic characteristics of irregular planform wings at Mach number 0.3

The subsonic aerodynamic characteristics of a series of irregular planform wings were studied in wind tunnel tests conducted at M = 0.3 over a range of Reynolds numbers from 1.6 million to 26 million/m. The five basic wing planforms varied from a trapezoidal to a delta shape. Leading edge extensions, added to the basic shape, varied in approximately 5 deg increments from the wing leading edge sweep-back angle to a maximum 80 deg. Most of the tests were conducted using an NACA 0008 airfoil section with grit boundary layer trips. Tests were also conducted using an NACA 0012 airfoil section and an 8% thick wedge. In addition, the effect of free transition (no grit) was investigated. A body was used on all models.

Kruse, R. L.↗
NASA NTRS1972

A study to determine the flight characteristics and handling qualitites of variable geometry spacecraft. Volume 3: Low L/D concept with fold-down wings

A study was conducted to determine the flight characteristics and wing deployment transients for a variable geometry spacecraft concept having a hypersonic lift-to-drag ratio near 1.0, and employing fold-down wings. Unpowered flight conditions were considered throughout the study. The body of the spacecraft uses a trapezoidal cross section. The variable geometry wings, stowed in the sides of the vehicle, are deployed at transonic speeds.

Friedman, G. R.↗
NASA NTRS1982

Experimental determination of flow-interference effects of wing-mounted, two-dimensional, full-capture propulsion nacelles in close proximity to a vehicle body at a Mach number of 6

Experimental tests have been conducted to determine possible aerodynamic interference effects due to the lateral positioning of two dimensional propulsion nacelles mounted on a wing surface in close proximity to a vehicle body. The tests were conducted at a Mach number of 6 and a Reynolds number 7 million per foot. The angle of attack range for force tests was -9 deg to 9 deg. The model configurations consisted of combinations of rectangular and trapezoidal cross section bodies with a wing swept 65 and a rectangular planform wing. A pair of two dimensional, flow through propulsion nacelles simulated full capture inlet operation.

Vahl, W. A.↗
NASA NTRS1961

Aerodynamic Characteristics of a Canard and an Outboard-Tail Airplane Model at High Subsonic Speeds

An investigation has been made in the Langley high-speed 7- by 10-foot tunnel through a range of Mach numbers from 0.60 to 0.95 of the static longitudinal and lateral stability and control characteristics of a canard airplane configuration and an outboard-tail configuration. The canard model had a twisted wing with approximately 67 deg of sweepback and an aspect ratio of 2.91 and was tested with three trapezoidal canard surfaces having ratios of exposed area to wing area of 0.032, 0.076, and 0.121. The canard model had a single body-mounted vertical tail. The outboard-tail model had its horizontal- and vertical-tail surfaces mounted on slender bodies attached to the wing tips and located to the rear and outboard of the 67 deg sweptback wing of aspect ratio 1.00. The data, which are presented with limited analysis, provide information at high subsonic speeds on these two types of high-speed airplanes which have previously been tested at supersonic speeds and reported in NACA RM L58BO7 and NACA RM L58E20.

Fournier, Paul G.↗
NASA NTRS1974

A quasi-vortex-lattice method in thin wing theory

A quasi-continuous method is developed for solving thin-wing problems. For the purpose of satisfying the wing boundary conditions, the spanwise vortex distribution is assumed to be stepwise-constant, while the chordwise vortex integral is reduced to a finite sum through a modified trapezoidal rule and the theory of Chebyshev polynomials. Wing-edge and Cauchy singularities are acounted for. The total aerodynamic characteristics are obtained by an appropriate quadrature integration. The two-dimensional results for airfoils without flap deflection reproduce the exact solutions in lift and pitching moment coefficients, the leading edge suction, and the pressure difference at a finite number of points. For a flapped airfoil, the present results are more accurate than those given by the vortex-lattice method. The three-dimensional results also show an improvement over the results of the vortex-lattice method. Extension to nonplanar applications is discussed.

Lan, C. E.↗
NASA NTRS1983

Supersonic aerodynamic characteristics of a tail-control cruciform maneuverable missile with and without wings

The aerodynamic characteristics for a winged and wingless cruciform missile configuration were examined. The configuration had an ogive-cylinder body with a 3.5 caliber forebody; an overall length-to-diameter ratio of 11.667; and had cruciform tails that were trapezoidal in planform. Tests were made both with and without 72.9 degree cruciform delta wings. The investigation was made for Mach numbers from 1.50 to 4.63, roll attitudes of 0 degrees and 45 degrees, angles of attack from -4 degrees to 22 degrees, and tail control deflections from 10 degrees to -40 degrees.

Spearman, M. L.↗
NASA NTRS1947

Voltera's Solution of the Wave Equation as Applied to Three-Dimensional Supersonic Airfoil Problems

A surface integral is developed which yields solutions of the linearized partial differential equation for supersonic flow. These solutions satisfy boundary conditions arising in wing theory. Particular applications of this general method are made, using acceleration potentials, to flat surfaces and to uniformly loaded lifting surfaces. Rectangular and trapezoidal plan forms are considered along with triangular forms adaptable to swept-forward and swept-back wings. The case of the triangular plan form in sideslip is also included. Emphasis is placed on the systematic application of the method to the lifting surfaces considered and on the possibility of further application.

Heslet, Max A↗
NASA NTRS1951

A summary of lateral-stability derivatives calculated for wing plan forms in supersonic flow

A compilation of theoretical values of the lateral-stability derivatives for wings at supersonic speeds is presented in the form of design charts. The wing plan forms for which this compilation has been prepared include a rectangular, two trapezoidal, two triangular, a fully-tapered swept-back, a sweptback hexagonal, an unswept hexagonal, and a notched triangular plan form. A full set of results, that is, values for all nine of the lateral-stability derivatives for wings, was available for the first six of these plan forms only. The reasons for the incompleteness of the results available for other plan forms are discussed.

Jones, Arthur L↗
NASA NTRS1986

Planform effects for low-fineness ratio multibody configurations at supersonic speeds

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration has been conducted in NASA Langley Research Center's Unitary Plan Wind Tunnel at Mach numbers 1.6, 1.8, 2.0, and 2.16. Experimental and theoretical values of lift, drag, and pitching moment were obtained on three configurations which varied in outboard panel planform only. The three variations were at 65 deg delta, a 70/66 deg cranked arrow, and a 20 deg trapezoidal planform . The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics and to evaluate the ability of two existing linearized-theory aerodynamic methods to predict these effects. Experimental data showed that the planforms produced the lift, drag-due-to-lift, and pitching-moment characteristics typically found on single-body configurations. However, the data also showed that planform has a minimal influence on zero-lift drag, which is not typical of single-body configurations. Theoretical aerodynamic analysis indicated that codes based on linearized theory adequately predicted the effect of planform on the supersonic aerodynamics.

Mcmillin, S. N.↗
NASA NTRS1993

Experimental aerodynamic characteristics of a generic hypersonic accelerator configuration at Mach numbers 1.5 and 2.0

An experimental investigation of the static longitudinal and lateral-directional aerodynamic characteristics of a generic hypersonic research vehicle was conducted in the Langley Unitary Plan Wind Tunnel (UPWT). A parametric study was performed to determine the interference effects of various model components. Configuration variables included delta and trapezoidal canards; large and small centerline-mounted vertical tails, along with a set of wing-mounted vertical tails; and a set of model noses with different degrees of bluntness. Wing position was varied by changing the longitudinal location and the incidence angle. The test Mach numbers were 1.5 and 2.0 at Reynolds numbers of 1 x 10(exp 6) per foot, 2 x 10(exp 6) per foot, and 4 x 10(exp 6) per foot. Angle of attack was varied from -4 degrees to 27 degrees, and sideslip angle was varied from -8 degrees to 8 degrees. Generally, the effect of Reynolds number did not deviate from conventional trends. The longitudinal stability and lift-curve slope decreased with increasing Mach number. As the wing was shifted rearward, the lift-curve slope decreased and the longitudinal stability increased. Also, the wing-mounted vertical tails resulted in a more longitudinally stable configuration. In general, the lift-drag ratio was not significantly affected by vertical-tail arrangement. The best lateral-directional stability was achieved with the large centerline-mounted tail, although the wing-mounted vertical tails exhibited the most favorable characteristics at the higher angles of attack.

Walker, Ira J.↗