Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Preliminary study of propulsion systems and airplane wing parameters for a US Navy subsonic V/STOL aircraft

Two V/STOL propulsion concepts were evaluated in a common aircraft configuration. One propulsion system consists of cross coupled turboshaft engines driving variable pitch fans. The other system is a gas coupled combination of turbojet gas generators and tip turbine fixed pitch fans. Evaluations were made of endurance at low altitude, low speed loiter with equal takeoff fuel loads. Effects of propulsion system sizing, bypass ratio, and aircraft wing planform parameters were investigated and compared. Shaft driven propulsion systems appear to result in better overall performance, although at higher installed weight, than gas systems.

Zola, C. L.↗
NASA NTRS1984

An investigation of aerodynamic characteristics of wings having vortex flow using different numerical codes

Three different numerical codes are employed to determine the aerodynamic characteristics of wings with separation induced vortex flows. Both flat as well as cambered wings of various planform shapes are studied. The effects of wing thickness, fuselage, notch ratio and multiple vortex modeling on aerodynamic performance of the wing are also examined. The theoretically predicted results are compared with experimental results to validate the various computer codes used in this study. An analytical procedure for designing aerodynamically effective leading edge extension (LEE) for a thick delta wing is also presented.

Sushil K Chaturvedi↗
NASA NTRS1976

Pressure distribution on a 1- by 3-meter semispan wing at sweep angles from 0 deg to 40 deg in subsonic flow

A 1- by 3-meter semispan wing of taper ratio 1.0 with NACA 0012 airfoil section contours was tested in the Langley V/STOL tunnel to measure the pressure distribution at five sweep angles, 0 deg, 10 deg, 20 deg, 30 deg, and 40 deg, through an angle-of-attack range from -6 deg to 20 deg. The pressure data are presented as plots of pressure coefficients at each static-pressure tap location on the wing. Flow visualization wing-tuft photographs are also presented for a wing of 40 deg sweep. A comparison between theory and experiment using two inviscid theories and a viscous theory shows good agreement for pressure distributions, normal forces, and pitching moments for the wing at 0 deg sweep.

Yip, L. P.↗
NASA NTRS1975

An investigation of supersonic aeroelastic characteristics of oblique winged aircraft

Two formulations of the oblique wing flutter problem are presented: one formulation allows wing bending deformations and the rigid body roll degree of freedom while the second formulation includes bending-torsional deformation and roll degrees of freedom. Flutter is found to occur in two basic modes. The first mode is associated with bending-roll coupling and occurs at low reduced frequency values. The other instability mode is primarily one of classical bending-torsion with negligible roll coupling; this mode occurs at much higher reduced frequencies. The occurrence of bending-roll coupling mode leads to lower flutter speeds while the bending-torsion mode is associated with higher flutter speeds. The ratio of the wing mass moment of inertial in roll to the fuselage moment of inertia evidently plays a major role in the determination of which of the two instabilities is critical.

Weisshaar, T. A.↗
NASA NTRS1971

Aerodynamics of lift fan V/STOL aircraft

V/stol aircraft lift fan aerodynamics, discussing optimum fan pressure ratios, augmentation ratio, noise constraints, wing loading and fan configurations

Hall, L. P.↗
NASA NTRS1975

Quiet Clean Short-haul Experimental Engine (QCSEE) UTW fan preliminary design

High bypass geared turbofan engines and propulsion systems designed for short-haul passenger aircraft are described. The propulsion technology required for future externally blown flap aircraft with engines located both under the wing and over the wing is emphasized. The aerodynamic and mechanical preliminary design of the QCSEE under the wing 1.34 pressure ratio fan with variable blade pitch is presented. Design information is given for two pitch change actuation systems which will provide reverse thrust.

Source record↗
NASA NTRS1980

Parametric study of variation in cargo-airplane performance related to progression from current to spanloader designs

A parametric analysis was made to investigate the relationship between current cargo airplanes and possible future designs that may differ greatly in both size and configuration. The method makes use of empirical scaling laws developed from statistical studies of data from current and advanced airplanes and, in addition, accounts for payload density, effects of span distributed load, and variations in tail area ratio. The method is believed to be particularly useful for exploratory studies of design and technology options for large airplanes. The analysis predicts somewhat more favorable variations of the ratios of payload to gross weight and block fuel to payload as the airplane size is increased than has been generally understood from interpretations of the cube-square law. In terms of these same ratios, large all wing (spanloader) designs show an advantage over wing-fuselage designs.

Toll, T. A.↗
NASA NTRS1934

The effects of equal-pressure fixed slots on the characteristics of a Clark Y Airfoil

A type of fixed open slot so arranged that no flow would pass through it at a lift coefficient corresponding to high-speed flight was investigated in the N.A.C.A. 7 by 10 foot wind tunnel to determine the possibilities of such a high-lift device for increasing the speed-range ratio of a wing. The condition of no through flow was achieved by locating the slot openings at points of equal static pressure at the design lift coefficient as determined from the pressure distribution about the plain wing. Two models of Clark Y wings with such equal-pressure slots were tested and the smoke-flow patterns about them observed. The results of this investigation show that the condition of no air flow through the slot at the desired lift coefficient is attainable. The surface discontinuities produced by the slot openings have, however, such a large effect on the drag that such slots show little promise. An appreciable increase is produced in the maximum lift and the speed-range can be as high as for the plain wing.

Harris, Thomas A↗
NASA NTRS1948

Free-flight Investigation at Transonic and Supersonic Speeds of the Rolling Effectiveness of a 42.7 Degree Sweptback Wing Having Partial-span Ailerons

An investigation of the rolling effectiveness at transonic and supersonic speeds of partial-span ailerons on a 42.7 degree sweptback wing having symmetrical circular-arc airfoil sections of 10-percent thickness ratio normal to the wing quarter-chord line has been made by means of rocket-propelled test vehicles. The results are compared with results of a supersonic wind-tunnel test at Mach number 1.9.

CONTROLS, LATERAL↗
NASA NTRS1942

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplane

An investigation was conducted in the NACA full-scale wind tunnel to determine the drag and the propulsive efficiency of nacelle-propeller arrangements for a large range of nacelle sizes. In contrast with usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a four-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplanes weighing from about 20 to 100 tons. The results show the drag, the propulsive efficiency, and the over-all efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model is shown for both propeller-removed and propeller-operating conditions.

Silverstein, Abe↗
NASA NTRS1956

Directional Stability of Towed Airplanes

So far, very careful investigations have been made regarding the flight properties, in particular the static and dynamic stability, of engine-propelled aircraft and of untowed gliders. In contrast, almost no investigations exist regarding the stability of airplanes towed by a towline. Thus, the following report will aim at investigating the directional stability of the towed airplane and, particularly, at determining what parameters of the flight attitude and what configuration properties affect the stability. The most important parameters of the flight attitude are the dynamic pressure, the aerodynamic coefficients of the flight attitude, and the climbing angle. Among the configuration properties, the following exert the greatest influence on the stability: the tow-cable length, the tow-cable attachment point, the ratio of the wing loadings of the towing and the towed airplanes, the moments of inertia, and the wing dihedral of the towed airplane. In addition, the size and shape of the towed airplane vertical tail, the vertical tail length, and the fuselage configuration are decisive factors in determining the yawing moment and side force due to sideslip, respectively.

Soehne, W.↗
NASA NTRS1939

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplanes, Special Report

An investigation is in progress in the NACA full-scale wind tunnel to determine the drag and propulsive efficiency of nacelle sizes. In contrast with the usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a 4-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplane weighing from about 20 to 100 tons. The results show that the drag, the propulsive efficiency, and the overall efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model are shown for both propeller-removed and propeller-operating conditions.

Silverstein, Abe↗
NASA NTRS1984

Aerodynamic canard/wing parametric analysis for general aviation applications

Vortex panel and vortex lattice methods have been utilized in an analytic study to determine the two- and three-dimensional aerodynamic behavior of canard and wing configurations. The purpose was to generate data useful for the design of general aviation canard aircraft. Essentially no two-dimensional coupling was encountered and the vertical distance between the lifting surfaces was found to be the main contributor to interference effects of the three-dimensional analysis. All canard configurations were less efficient than a forward wing with an aft horizontal tail, but were less sensitive to off-optimum division of total lift between the two surfaces, such that trim drag could be less for canard configurations. For designing a general aviation canard aircraft, results point toward large horizontal and vertical distance between the canard and wing, a large wing-to-canard area ratio, and with the canard at a low incidence angle relative to the wing.

Keith, M. W.↗
NASA NTRS1993

Grid and aerodynamic sensitivity analyses of airplane components

An algorithm is developed to obtain the grid sensitivity with respect to design parameters for aerodynamic optimization. The procedure is advocating a novel (geometrical) parameterization using spline functions such as NURBS (Non-Uniform Rational B-Splines) for defining the wing-section geometry. An interactive algebraic grid generation technique, known as Two-Boundary Grid Generation (TBGG) is employed to generate C-type grids around wing-sections. The grid sensitivity of the domain with respect to geometric design parameters has been obtained by direct differentiation of the grid equations. A hybrid approach is proposed for more geometrically complex configurations such as a wing or fuselage. The aerodynamic sensitivity coefficients are obtained by direct differentiation of the compressible two-dimensional thin-layer Navier-Stokes equations. An optimization package has been introduced into the algorithm in order to optimize the wing-section surface. Results demonstrate a substantially improved design due to maximized lift/drag ratio of the wing-section.

Sadrehaghighi, Ideen↗
NASA NTRS1987

High angle of attack hypersonic aerodynamics

A new aerodynamics force model is presented which is based on modified Newtonian theory and empirical correlations. The algebraic model was developed for complete vehicles from take off to orbital speeds and for large angles of attack. Predictions are compared to results for a wind tunnel model at a Mach number of 20, and the full scale Shuttle Orbiter for Mach numbers from 0.25 to 20 for angles of attack from 0 to 50 deg. The maximum shuttle orbiter lift/drag at Mach 10 and 20 is 1.85 at 20-deg angle-of-attack. Aerodynamic force predictions are made for a transatmospheric vehicle, which is a derivative of the Shuttle Orbiter, for Mach numbers from 4 to 27 at angles of attack from 5 to 40 deg. Predicted aerodynamic force data indicate that lift/drag ratios of 5.2 at Mach number 10 and 3.6 at Mach number 26 are obtainable. Changes in force coefficients with changes in: nose angle, sweep angle, and (volume exp 2/3)/planform area are quantified for Mach numbers of 10 and 26. Lift/drag ratios increase with decreasing nose angle and (volume exp 2/3)/planform area and increasing wing sweep angle. Lift/drag ratios are independent of these variables for angles of attack in excess of 20 deg at Mach 10 and 30 deg at Mach 26.

Harloff, Gary J.↗