Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - LIFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Flight-measured buffet characteristics of a supercritical wing and a conventional wing on a variable-sweep airplane

Windup-turn maneuvers were performed to assess the buffet characteristics of the F-111A aircraft and the same aircraft with a supercritical wing, which is referred to as the F-111 transonic aircraft technology (TACT) aircraft. Data were gathered at wing sweep angles of 26, 35, and 58 deg for Mach numbers from 0.60 to 0.95. Wingtip accelerometer data were the primary source of buffet information. The analysis was supported by wing strain-gage and pressure data taken in flight, and by oil-flow photographs taken during tests of a wind tunnel model. In the transonic speed range, the overall buffet characteristics of the aircraft having a supercritical wing are significantly improved over those of the aircraft having a conventional wing.

Monaghan, R. C.↗
NASA NTRS1979

Wind-tunnel investigation of a large-scale VTOL aircraft model with wing root and wing thrust augmentors

Tests were conducted in the Ames 40 by 80 foot wind tunnel to determine the aerodynamic characteristics of a large-scale V/STOL aircraft model with thrust augmentors. The model had a double-delta wing of aspect ratio 1.65 with augmentors located in the wing root and the wing trailing edge. The supply air for the augmentor primary nozzles was provided by the YJ-97 turbojet engine. The airflow was apportioned approximately 74 percent to the wing root augmentor and 24 percent to wing augmentor. Results were obtained at several trailing-edge flap deflections with the nozzle jet-momentum coefficients ranging from 0 to 7.9. Three-component longitudinal data are presented with the agumentor operating with and without the horizontal tail. A limited amount of six component data are also presented.

Aoyagi, K.↗
NASA NTRS1981

Self-induced wing rock of slender delta wings

As part of a research program aimed at exploring basic mechanisms that cause wing rock in combat aircraft, an investigation was conducted to study the aerodynamic factors which cause the low-speed wing rock exhibited by slender delta wings. A flat-plate delta wing with 80 deg leading-edge sweep was subjected to conventional static-force tests and dynamic wind-tunnel experiments which included forced-oscillation, rotary, and free-to-roll tests. In addition, visualization of the flow phenomena involved was obtained by observing tuft patterns and using a helium-bubble technique. This paper summarizes the results of this study. Fundamental information is presented on the aerodynamic mechanisms that cause the wing rock and the problem of mathematically modeling the aerodynamics and motions is discussed.

Nguyen, L. T.↗
NASA NTRS1986

An investigation of tip planform influence on the aerodynamic load characteristics of semispan, upswept wing and wing-tip

A semi-span wing, equipped with an interchangeable tip, which was varied in planform and size was examined. Total wing aerodynamic loading was obtained from the wind tunnel scale system. The wing tip was mounted on a separate six-component strain gauge balance, which provided the aerodynamic loads on the tip. The tests were accomplished in the NASA Ames 7X10-Foot Wind Tunnel at a Mach number of 0.178. The aerodynamic load characteristics of the wing and of the tip were presented with the tip at several incidence angles relative to the wing inboard section.

Vanaken, Johannes M.↗
NASA NTRS1937

Free-spinning Wind-tunnel Tests of a Low-wing Monoplane with Systemic Changes in Wings and Tails

A series of tests was made at the National Advisory Committee for Aeronautics (NACA) free-spinning tunnel to determine the effect of systematic changes in wing and tail arrangement upon steady-spinning and recovery characteristics of a conventional low-wing monoplane model for a basic loading condition. Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 wing-tail combinations, observations were made of steady spins for four control settings and of recoveries for five control manipulators. The results are presented in the form of charts comparing the spin characteristics. The results showed that, with a poor tail arrangement, wing plan form and tip shape had a considerable effect on the spinning characteristics.

Seidman, Oscar↗
NASA NTRS1935

Tests of Nacelle-Propeller Combinations in Various Positions with Reference to Wings VI : Wings and Nacelles with Pusher Propeller

This report is the sixth of a series giving wind tunnel tests results on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. The present report gives the results of tests of a radial-engine nacelle with pusher propeller in 17 positions with reference to a Clark Y wing; tests of the same nacelle and propeller in three positions with reference to a thick wing; and tests of a body and pusher propeller with the thick wing, simulating the case of a propeller driven by an extension shaft from an engine within the wing. Some preliminary tests were made on pusher nacelles alone.

Wood, Donald H↗
NASA NTRS1994

Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included.

Hernandez, Gloria↗
NASA NTRS1959

Subsonic Wing Loadings on a 45 deg Sweptback Wing and Body Combination at High Angles of Attack

A study has been made of the subsonic pressure distributions and loadings for a 45 deg sweptback-wing and body combination at angles of attack up to 36 deg. The wing had an aspect ratio of 5.5, a taper ratio of 0.53, and NACA 64A010 sections normal to the quarter-chord line and was mounted on a slender body of fineness ratio 12.5. Test results are presented for Mach numbers of 0.30 and 0.50 with corresponding Reynolds numbers of 1.5 and 2.0 million, respectively. The stall patterns and spanwise loadings at high angles of attack for the present model are correlated with those for other 45 deg sweptback wing and body combinations having aspect ratios between 4.0 and 8.0. A tentative approach is presented for extrapolating the Weissinger span-loading method to higher angles of attack, and for deriving the spanwise-load distributions for 45 deg sweptback wings at angles of attack above 20 deg. The investigation also included tests of the body in combination with only one panel of the swept wing. The problem of estimating the normal-force coefficient for the single panel at high angles of attack is considered.

Axelson, John A↗
NASA NTRS2002

Wing Torsional Stiffness Tests of the Active Aeroelastic Wing F/A-18 Airplane

The left wing of the Active Aeroelastic Wing (AAW) F/A-18 airplane has been ground-load-tested to quantify its torsional stiffness. The test has been performed at the NASA Dryden Flight Research Center in November 1996, and again in April 2001 after a wing skin modification was performed. The primary objectives of these tests were to characterize the wing behavior before the first flight, and provide a before-and-after measurement of the torsional stiffness. Two streamwise load couples have been applied. The wing skin modification is shown to have more torsional flexibility than the original configuration has. Additionally, structural hysteresis is shown to be reduced by the skin modification. Data comparisons show good repeatability between the tests.

Lokos, William A.↗
NASA NTRS1929

Cantilever Wings for Modern Aircraft: Some Aspects of Cantilever Wing Construction with Special Reference to Weight and Torsional Stiffness

In the foregoing remarks I have made an attempt to touch on some of the structural problems met with in cantilever wings, and dealt rather fully with a certain type of single-spar construction. The experimental test wing was a first attempt to demonstrate the principles of this departure from orthodox methods. The result was a wing both torsionally stiff and of light weight - lighter than a corresponding biplane construction.

WINGS - STRUCTURE↗
NASA NTRS1973

A study of the effects of aeroelastic divergence on the wing structure of an oblique-wing supersonic transport configuration

The aerodynamic characteristics of transport aircraft with oblique wing flying at supersonic speeds are discussed. Aeroelastic divergence of the forward swept portion of the wing is analyzed. The effect of aspect ratio as a method for avoiding aeroelastic divergence is examined. A relatively low aspect ratio appears necessary for an oblique wing when constructed of conventional aluminum alloy materials. The aspect ratio may be increased by increasing the wing thickness ratio and by utilizing materials with higher moduli of elasticity and rigidity.

Source record↗
NASA NTRS1972

EBF noise tests with engine under-the-wing and over-the-wing configurations

Noise tests of externally blown flaps with the engine under the wing and engine over the wing configurations were conducted. Flap noise data obtained on a TF-34 aircraft are discussed. Noise data obtained during a free-jet forward-speed-effect analysis are presented. Noise sources associated with upper surface flap blowing are described. Results of a small scale configuration screening study and some large scale model test data are analyzed. The noise data for the engine over wing configurations are compared with the engine under the wing configurations.

Dorsch, R. G.↗
NASA NTRS1976

Effects of wing leading-edge radius and Reynolds number on longitudinal aerodynamic characteristics of highly swept wing-body configurations at subsonic speeds

An investigation was conducted in the Langley low turbulence pressure tunnel to determine the effects of wing leading edge radius and Reynolds number on the longitudinal aerodynamic characteristics of a series of highly swept wing-body configurations. The tests were conducted at Mach numbers below 0.30, angles of attack up to 16 deg, and Reynolds numbers per meter from 6.57 million to 43.27 million. The wings under study in this investigation had leading edge sweep angles of 61.7 deg, 64.61 deg, and 67.01 deg in combination with trailing edge sweep angles of 0 deg and 40.6 deg. The leading edge radii of each wing planform could be varied from sharp to nearly round.

Henderson, W. P.↗
NASA NTRS1979

Exploratory study of the influence of wing leading-edge modifications on the spin characteristics of a low-wing single-engine general aviation airplane

A wide variety of model and airplane tests were conducted to explore the effects of wing leading-edge modifications on the stalling and spinning characteristics of a low-wing general aviation research airplane configuration. The results presented herein discuss the effects of leading-edge airfoil modifications applied to the full wing span and to partial-span locations. The results obtained in the study indicate that the wing modifications can produce large effects (both favorable or unfavorable) on spin resistance, developed spin characteristics, and spin recovery.

Dicarlo, D. J.↗
NASA NTRS1982

Wing flap-type control effectiveness and effects of control hinge gap seals for a supercritical wing

Wind-tunnel tests were made to investigate the control effectiveness of wing trailing-edge flap-type aerodynamic controls for a supercritical wing. The tests determined the effects of spanwise flap control location, two different wing transition grit location patterns, magnitude of angular control deflection, control hinge moments and control hinge gap seals. Results show that the inboard flap position deflections caused interference rearward at the vertical tail, and that all flap positions for deflections in one direction only caused interference at the horizontal tail at a higher than design Mach number. Changes in wing transition grit pattern caused significant changes to static longitudinal characteristics and longitudinal control effectiveness.

Anglin, E. L.↗
NASA NTRS1983

Numerical simulation of the leading-edge separation vortex for a wing and strake-wing configuration

In the present investigation, the 'thin layer' Navier-Stokes equations are used to compute the flow about a delta wing and a strake-delta wing configuration. Both configurations possess blunt noses and rounded leading edges. The computational grid about these configurations is generated using a newly developed three-dimensional grid-generation code which solves a set of Poisson equations with spherical coordinate variables using an alternating direction implicit (ADI) scheme. Computational results are obtained for an isolated wing with 60 deg sweep and a strake-wing configuration with 80-60 deg sweep. Computations for angles of attack in the range from 6 to 30 deg are presented. Attention is given to the effect of the angle of attack, the Mach number, and the Reynolds number. Theoretical results are compared with experimental data.

Fujii, K.↗
NASA NTRS1983

Wing loading on a 60 degree delta wing with vortex flaps

Wind tunnel tests were conducted on a 60 deg delta wing with three vortex flap designs to determine pressure distributions over the wing and flap. The results showed that an optimum vortex flap design depends on proper definition of the vortex flap deflection angle. They also revealed that flap thickness plays an important role in the behavior of the vortex flow over the flap and wing and can have a substantial effect on wing and flap pressure loading. Design codes which fail to account for thickness may result in a much less than optimum flap and deprive the designer of an important tool in designing an effective flap with optimum loading.

Marchman, J. F., III↗