Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wall conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Turbulent boundary layer on a convex, curved surface

The effects of strong convex curvature on boundary layer turbulence were investigated. The data gathered on the behavior of Reynolds stress suggested the formulation of a simple turbulence model. Three sets of data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning, and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero - thus avoiding any effects of streamwise acceleration on the wall layers. Results show that after a sudden introduction of curvature, the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. In contrast, when the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions.

Gillis, J. C.↗
NASA NTRS1981

Experimental data and model for the turbulent boundary layer on a convex, curved surface

Experiments were performed to determine how boundary layer turbulence is affected by strong convex curvature. The data gathered on the behavior of the Reynolds stress suggested the formulation of a simple turbulence model. Data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero. Two experiments were performed at delta/R approximately 0.10, and one at weaker curvature with delta/R approximately 0.05. Results show that after a sudden introduction of curvature the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. When the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions. A simple turbulence model, which was based on the theory that the Prandtl mixing length in the outer layer should scale on the velocity gradient layer, was shown to account for the slow recovery.

Gillis, J. C.↗
NASA NTRS1983

Iterative PNS method for attached flows with upstream influence

A stable global-iteration procedure is developed by utilizing successive sweeps, from inflow to outflow boundaries, of a parabolized Navier-Stokes code for attached, steady supersonic flow. It is shown that the procedure converges in about ten or fewer iterations, and allows for the upstream influence within the subsonic region of a supersonic boundary layer. An implicit forward difference is employed in the subsonic region to evaluate the pressure-gradient term in the streamwise momentum equation. The pressure-gradient term is normally approximated in standard single-sweep parabolized methods, suppressing the upstream influence. The iterative results obtained demonstrate the validity of the single-sweep method for weak interactions. For hypersonic viscous interaction on a flat plate at a Mach number of 5.8, it is found that the single-sweep method has a small error that vanishes as the Reynolds number of the flow is increased. However, the skin friction has an error of about 10 percent for low Reynolds numbers and for hot wall conditions. The application of this method to laminar two-dimensional flow over weak expansion and compression corners shows that the pressure and skin friction results in the vicinity of the expansion corner compare favorably with a time-dependent Navier-Stokes numerical solution.

Rakich, J. V.↗
NASA NTRS1984

Numerical simulation of controlled flow tunnel for V/STOL testing

A 'smart' wind tunnel concept for V/STOL transition regime studies is presented and performance is projected with numerical simulations. The wind tunnel would provide a flow that faithfully represents free air flow and thereby permits accurate lift calculations for V/STOL aircraft. The design concept is based on free-air tunnels used for planar wings. Modifications are necessary to account for the highly deflected, vortical wake produced in low-speed take-off and landing situations. A three-step numerical procedure covering the potential flow of a high lift system in free-air, controlled flow data with a model in a wind tunnel and addition of the wall conditions to the simulation as a feedback loop to correct the closed-tunnel is described. The initial simulation is for three-dimensional full span jet flapped wings, and is derived from extended two-dimensional calculations. The results indicate that only partial control of the tunnel flow is sufficient to serve as a valid environment for V/STOl studies.

Joppa, R. G.↗
NASA NTRS1985

A 3-dimensional Navier-Stokes-Euler code for blunt-body flow computations

The shock-layer flowfield is obtained with or without viscous and heat-conducting dissipations from the conservative laws of fluid dynamics equations using a shock-fitting implicity finite-difference technique. The governing equations are cast in curvilinear-orthogonal coordinates and transformed to the domain between the shock and the body. Another set of equations is used for the singular coordinate axis, which, together with a cone generator away from the stagnation point, encloses the computation domain. A time-dependent alternating direction implicit factorization technique is applied to integrate the equations with local-time increment until a steady solution is reached. The shock location is updated after the flowfield computation, but the wall conditions are implemented into the implicit procedure. Innovative procedures are introduced to define the initial flowfield, to treat both perfect and equilibrium gases, to advance the solution on a coarse-to-fine grid sequence, and to start viscous flow computations from their corresponding inviscid solutions. The results are obtained from a grid no greater than 28 by 18 by 7 and converged within 300 integration steps. They are of sufficient accuracy to start parabolized Navier-Stokes or Euler calculations beyond the nose region, to compare with flight and wind-tunnel data, and to evaluate conceptual designs of reentry spacecraft.

Li, C. P.↗
NASA NTRS1987

Numerical simulation of compressible flow around complex two-dimensional cavities

Compressible viscous flow around two-dimensional cavities, that model the midplane flow in and around an airborne telescope cavity, are obtained through numerical simulation. Numerical solutions using the patched grid CSCM scheme for compressible, unsteady flow are presented for the cavities, with and without blowing. The time evolving solutions show interesting flow features. Relevant results for a limited number of problems presented here show the unsteady nature of the flow and its dependence on various parameters such as Reynolds number, the wall conditions, etc. The voluminous data of time evolving flow field solutions are analyzed through movies of the velocity vectors, and contours of other flow variables.

Venkatapathy, Ethiraj↗
NASA NTRS1987

A mapped finite difference study of noise propagation in nonuniform ducts with mean flow

The primary objective of this work is to study noise propagation in acoustically lined variable area ducts with mean fluid flow. The method of study is numerical in nature and involves a body-fitted grid mapping procedure in conjunction with a factored-implicit finite difference technique. The mean fluid flow model used is two-dimensional, inviscid, irrotational, incompressible, and nonheat conducting. Fully-coupled solutions of the linearized gasdynamic equations are obtained for both positive and negative Mach numbers as well as for hard and soft wall conditions. The factored-implicit finite difference technique used did give rise to short wavelength perturbations, but these were dampened by the introduction of higher order artificial dissipation terms into the scheme. Results compared favorably with available numerical and experimental data.

Raad, Peter E.↗
NASA NTRS1990

The inviscid stability of supersonic flow past a sharp cone

The effects of lateral curvature on the development of supersonic laminar inviscid boundary-layer flow on a sharp cone with adiabatic wall conditions are investigated analytically, with a focus on the linear temporal inviscid stability properties. The derivation of the governing equations and of a 'triply generalized' inflexion condition is outlined, and numerical results for freestream Mach number 3.8 are presented in extensive graphs and characterized in detail. A third instability mode related to the viscous mode observed by Duck and Hall (1990) using triple-deck theory is detected and shown to be more unstable and to have larger growth rates than the second mode in some cases. It is found that the 'sonic' neutral mode is affected by the lateral curvature and becomes a supersonic neutral mode.

Duck, Peter W.↗
NASA NTRS1991

On the stability of compressible flow past axisymmetric bodies

Compressible linear stability theory for axisymmetric flows is presented. The theory is applied to flow past a cylinder and a sharp cone at a Mach number of 5 with adiabatic wall conditions. The effect of transverse curvature and body divergence is studied. It is found that transverse curvature has a stabilizing influence on axisymmetric (first and second mode) disturbances while it has a destabilizing influence on the asymmetric (oblique first mode) disturbances. The body divergence effects are stabilizing for both symmetric and asymmetric disturbances. Comparisons made with the results of planar stability theory show that, for a cylinder, curvature effects become more pronounced with increasing distance along the cylinder. For a sharp cone, these effects become less significant further away from the cone tip since the body radius increases faster than the growth of the boundary layer. The effect of cone angle on stability is also studied.

Malik, M. R.↗
NASA NTRS1991

Analysis of flight-measured boundary-layer stability and transition data

The paper concentrates on the computational analysis of both the Tollmien-Schlichting and crossflow-type instabilities using the results of a boundary-layer transition flight experiment on a smooth swept test surface. In addition, the effect of nonadiabatic wall conditions is analyzed using the measured surface temperature distribution on the boundary-layer development and stability growth. The computational methods utilized in analyzing the boundary-layer stability characteristics are discussed: one approach analyzes the Tollmien-Schlichting and crossflow instabilities independently with maximum Tollmien-Schlichting n-factors near nine and maximum crossflow n-factors near six at transition onset for separate cases, while the second approach analyzes the instabilities for maximum growth regardless of the type. As much as a 27-percent increase in n-factor is found at transition onset due to an increased Tollmien-Schlichting instability.

Obara, Clifford J.↗
NASA NTRS1992

An experimental/computational study of sharp fin induced shock wave/turbulent boundary layer interactions at Mach 5 - Experimental results

A combined experimental/computational study has been performed of sharp fin induced shock wave/turbulent boundary layer interactions at Mach 5. The current paper focuses on the experiments and analysis of the results. The experimental data include mean surface heat transfer, mean surface pressure distributions and surface flow visualization for fin angles of attack of 6, 8, 10, 12, 14 and 16-degrees at Mach 5 under a moderately cooled wall condition. Comparisons between the results and correlations developed earlier show that Scuderi's correlation for the upstream influence angle (recast in a conical form) is superior to other such correlations in predicting the current results, that normal Mach number based correlations for peak pressure heat transfer are adequate and that the initial heat transfer peak can be predicted using pressure-interaction theory.

Rodi, Patrick E.↗
NASA NTRS1992

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗
NASA NTRS1995

Exhausted Plume Flow Field Prediction Near the Afterbody of Hypersonic Flight Vehicles in High Altitudes

A two-dimensional computer code to solve the Burnett equations has been developed which computes the flow interaction between an exhausted plume and hypersonic external flow near the afterbody of a flight vehicle. This Burnett-2D code extends the capability of Navier-Stokes solver (RPLUS2D code) to include high-order Burnett source terms and slip-wall conditions for velocity and temperature. Higher-order Burnett viscous stress and heat flux terms are discretized using central-differencing and treated as source terms. Blocking logic is adopted in order to overcome the difficulty of grid generation. The computation of exhaust plume flow field is divided into two steps. In the first step, the thruster nozzle exit conditions are computed which generates inflow conditions in the base area near the afterbody. Results demonstrated that at high altitudes, the computations of nozzle exit conditions must include the effects of base flow since significant expansion exists in the base region. In the second step, Burnett equations were solved for exhaust plume flow field near the afterbody. The free stream conditions are set at an altitude equal to 80km and the Mach number is equal to 5.0. The preliminary results show that the plume expansion, as altitude increases, will eventually cause upstream flow separation.

Chou, Lynn Chen↗
NASA NTRS1998

Boundary Layer Transition in the Leading Edge Region of a Swept Cylinder in High Speed Flow

Experiments were conducted on a 76 degree swept cylinder to establish the behavior of the attachment line transition process in a low-disturbance level, Mach number 1.6 flow. For a near adiabatic wall condition, the attachment-line boundary layer remained laminar up to the highest attainable Reynolds number. The attachment-line boundary layer transition under the influence of trip wires depended on wind tunnel disturbance level, and a transition onset condition for this flow is established. Internal heating raised the surface temperature of the attachment line to induce boundary layer instabilities. This was demonstrated experimentally for the first time and the frequencies of the most amplified disturbances were determined over a range of temperature settings. Results were in excellent agreement to those predicted by a linear stability code, and provide the first experimental verification of theory. Transition onset along the heated attachment line at an R-bar of 800 under quiet tunnel conditions was found to correlate with an N factor of 13.2. Increased tunnel disturbance levels caused the transition onset to occur at lower cylinder surface temperatures and was found to correlate with an approximate N factor of 1 1.9, so demonstrating that the attachment-line boundary layer is receptive to increases in the tunnel disturbance level.

Coleman, Colin P.↗
NASA NTRS2009

Compressibility Considerations for kappa-omega Turbulence Models in Hypersonic Boundary Layer Applications

The ability of kappa-omega models to predict compressible turbulent skin friction in hypersonic boundary layers is investigated. Although uncorrected two-equation models can agree well with correlations for hot-wall cases, they tend to perform progressively worse - particularly for cold walls - as the Mach number is increased in the hypersonic regime. Simple algebraic models such as Baldwin-Lomax perform better compared to experiments and correlations in these circumstances. Many of the compressibility corrections described in the literature are summarized here. These include corrections that have only a small influence for kappa-omega models, or that apply only in specific circumstances. The most widely-used general corrections were designed for use with jet or mixing-layer free shear flows. A less well-known dilatation-dissipation correction intended for boundary layer flows is also tested, and is shown to agree reasonably well with the Baldwin-Lomax model at cold-wall conditions. It exhibits a less dramatic influence than the free shear type of correction. There is clearly a need for improved understanding and better overall physical modeling for turbulence models applied to hypersonic boundary layer flows.

Rumsey, C. L.↗
NASA NTRS1983

Wall-function boundary conditions in the solution of the Navier-Stokes equations for complex compressible flows

To make computer codes for two-dimensional compressible flows more robust and economical, wall functions for these flows, under adiabatic conditions, have been developed and tested. These wall functions have been applied to three two-equation models of turbulence. The tests consist of comparisons of calculated and experimental results for transonic and supersonic flow over a flat plate and for two-dimensional and axisymmetrical transonic shock-wave/boundary-layer interaction flows with and without separation. The calculations are performed with an implicit algorithm that solves the Reynolds-averaged Navier-Stokes equations. It is shown that results obtained agree very well with the data for the complex compressible flows tested, provided criteria for use of the wall functions are followed. The expected savings in cost of the computations and improved robustness of the code were achieved.

Viegas, J. R.↗
NASA NTRSDate not supplied

Numerical Investigation of Heat Transfer on the NASA SIDRM Model

NASA has developed a Simulated Inter-Duct Research Model (SIDRM) to study ice crystal icing in aircraft engines. A numerical investigation has been completed using the NASA in-house code, GlennHT. For each flow condition, many different wall thermal boundary conditions were imposed. Six uniform wall temperature cases were generated, with wall temperature relative to the freestream total temperature of 0.85, 0.90, 0.95, 1.05, 1.10, and 1.15. In addition, five cases with uniform heat flux were generated. Heat fluxes were chosen to generate average wall temperatures in the range explored by the uniform wall temperature cases. Included in the uniform heat flux cases is the adiabatic case where heat flux equals zero. The results of these simulations are then used to quantify the degree to which the heat transfer coefficient depends on wall thermal boundary condition. It is seen that the heat transfer coefficient is fairly independent of wall thermal boundary condition, as expected. However, it would appear that, at least in some locations, it may be prudent to attempt to correlate a variation of heat transfer coefficient with wall thermal boundary condition.

Ice Crystal Icing↗
NASA NTRS1984

Effect of boundary layers on solid walls in three-dimensional subsonic wind tunnels

A solution for the tunnel wall boundary layer effects for three-dimensional subsonic tunnels is presented. The model potentials are represented with simple singularities placed on the centerline of the tunnel and Laplace's equation in cylindrical coordinates is solved for either the conventional homogeneous slotted-wall boundary condition, the solid-wall viscous boundary condition, or a combination of them. The most pronounced wall boundary layer effect is on solid blockage for completely closed wind tunnels. Boundary layers on the wall reduce the blockage from the solid-wall, no-boundary-layer case in a manner similar to opening slots in a solid wall. Additionally, for solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, whereas the lift interference factor at the model station does not depend on the boundary layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Adcock, J. B.↗