Search NASA⌕ Search

SEARCH · Search NASA

Results for “YAWING MOMENTS - AILERONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Lateral control at high angles of attack using pneumatic blowing through a chined forebody

Directional control through the use of pneumatic blowing was investigated on a generic subscale model with a chined forebody with blowing through a chine slot in a direction normal to the forebody surface. Comparisons are made with a vertical tail on and off, and with control through rudder deflection. Force and moment data were obtained for various blowing coefficients over a 0-75 deg alpha range, and flow visualization was also conducted in order to see qualitative effects on the flowfield. Blowing through a chined forebody generates yaw moments at large alpha where control surfaces lose their effectiveness; these moments are much larger than obtained by jet thrust alone, since the forebody flowfield is modified through the interaction of the jet with the chine vortices. Directional control increased with angle of attack for a given blowing coefficient until a maximum was reached. Further increases in angle of attack results in a rapid loss of effectiveness. For angles of attack above 60 deg, yaw moments are generated by simple jet thrust effect. The effectiveness of the pneumatic system depended on tail configuration.

Arena, A. S., Jr.↗
NASA NTRS1976

Experimental aerodynamic characteristics for slender bodies with thin wings at angles of attack from 0 deg to 58 deg and Mach numbers from 0.6 to 2.0

An experimental investigation was conducted in the Ames 6-by-6-Foot Wind Tunnel to measure the static aerodynamic characteristics for bodies of circular and elliptic cross section with various thin flat-plate wings. Eighteen configuration combinations were tested at Mach numbers of 0.6, 0.9, 1.2, 1.5, and 2.0 at angles of attack from 0 deg to 58 deg. The data demonstrate that taper ratio and aspect ratio had only small effect on the aerodynamic characteristics, especially at the higher angles of attack. Undesirable side forces and yawing moments, which developed at angles of attack greater than about 25 deg, were generally no greater than those for the bodies tested alone. As for the bodies alone, the side forces and yawing moments increased as the nose fineness ratio increased and/or as the subsonic Mach number decreased.

Jorgensen, L. H.↗
NASA NTRS1977

An investigation of a close-coupled canard as a direct side-force generator on a fighter model at Mach numbers from 0.40 to 0.90

The canard panels had 5 deg of dihedral and were deflected differentially or individually over an incidence range from 10 deg to -10 deg and a model angle-of-attack range from -4 deg to 15 deg. Significant side forces were generated in a transonic tunnel by differential and single canard-panel deflections over the Mach number and angle-of-attack ranges. The yawing moment resulting from the forward location of the generated side force would necessitate a vertical tail/rudder trim force which would augment the forebody side force and be of comparable magnitude. Incremental side forces, yawing moments, lift, and pitching moments due to single canard-panel deflections were additive; that is, their sums were essentially the same as the forces and moments produced by differential canard-panel deflections of the same magnitude. Differential and single canard-panel deflections produced negligible rolling moments over the Mach number and angle-of-attack ranges.

Re, R. J.↗
NASA NTRS1989

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Low-speed wind tunnel experiments have been conducted to define methods for the manipulation of a generic fighter forebody's vortices in order to generate controlled yawing moments at high alpha. Attention is given to two vortex-control schemes: one involving independently controlled forebody tip strakes, and the other individually controlled blowing ports on the forebody. The most effective methods for forebody yawing-moment control were found to be the minimization of natural asymmetry with a pair of symmetrically mounted tip strakes, and the perturbation of the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗
NASA NTRS1992

Forebody flow control on a full-scale F/A-18 aircraft

A full-scale F/A-18 was tested in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center to measure the effectiveness of pneumatic forebody vortex control devices. By altering the forebody vortex flow, yaw control can be maintained to angles of attack greater than 50 deg. Two forebody vortex control devices were tested: a discrete circular jet and a tangential slot. The tests were conducted for angles of attack between 25 and 50 deg, and angles of sideslip from 0 to +/- 15 deg. The Reynolds number based on wing mean aerodynamic chord ranged from 4.5 x 10 exp 6 to 12.0 x 10 exp 6. The time-averaged side forces and yawing moments, along with both time-averaged and time-dependent pressures on the forebody of the aircraft are presented here for various configurations. Of particular interest was the results that the tangential slot blowing had a greater effect on the yawing moment than the discrete circular jet. Additionally, it was found that blowing very close to the radome apex was not as effective as blowing slightly farther aft on the radome, and that a 16-inch slot was more effective than either an 8- or 48-inch long slot.

Lanser, Wendy R.↗
NASA NTRS1958

Estimation of Directional Stability Derivatives at Small Angles and Subsonic and Supersonic Speeds

Methods are presented for estimating the directional stability derivative increments contributed by the stabilizing surfaces of subsonic and supersonic aircraft. These methods are strictly applicable at zero angle of attack and small angles of sideslip. The procedure of totaling the incremental coefficients to obtain an estimation of the total empennage side-force and yawing-moment coefficient derivatives is also shown, together with numerical examples. A correlation is presented between estimated and experimental incremental coefficients which indicates that the methods of this report generally estimate the increment of side force gained by the addition of a panel to within +/-10 percent of the experimental value while the yawing-moment increment is generally estimated to within +/-20 percent. This is true for both subsonic and supersonic Mach numbers. An example application of the methods to one of the problems in directional stability, that of minimizing the effect of Mach number on the side-force coefficient derivative of the empennage, is discussed.

Goodwin, Frederick K.↗
NASA NTRS1994

Wind tunnel measurements on a full-scale F/A-18 with a tangentially blowing slot

A full-scale F/A-18 was tested in the 80 by 120-Foot Wind Tunnel at NASA Ames Research Center to measure the effectiveness of a tangentially blowing slot in generating significant yawing moments while minimizing coupling in the pitch and roll axes. Various slot configurations were tested to determine the optimum configuration. The test was conducted for angles of attack from 25 to 50 deg, angles of sideslip from -15 to +15 deg, and freestream velocities from 67 ft/sec to 168 ft/sec. By altering the forebody vortex flow, yaw control was maintained for angles of attack up to 50 deg. Of particular interest was the result that blowing very close to the radome apex was not as effective as blowing slightly farther aft on the radome, that a 16-inch slot was more efficient, and that yawing moments were generated without inducing significant rolling or pitching moments.

Lanser, Wendy R.↗
NASA NTRS1960

Experimental Determination of the Effects of Frequency and Amplitude of Oscillation on the Roll-Stability Derivatives for a 60 Degree Delta-Wing Airplane Model

A 60' delta-wing airplane model was oscillated in roll for several frequencies and amplitudes of oscillation to determine the effects of the oscillatory motion on the roll-stability derivatives for the model. The derivatives were measured at a Reynolds number of 1,600,000 for the wing alone, the wing-fuselage combination, and the complete model which included a triangular-plan-form vertical tail. Both rolling and yawing moments due to rolling velocity exhibited large frequency effects for angles of attack higher than 16 degrees. Variations in these derivatives were measured for the lowest frequencies of oscillation; as the frequency increased, the derivatives because more nearly linear with angle of attack. Both velocity derivatives were considerably different at high angles of attack from the corresponding derivatives measured by the steady-state rolling-flow technique. Rolling and yawing moments due to rolling acceleration were measured and similarly found to be highly dependent on frequency at high angles of attack. Some period and time-to-damp computations, which were made to reveal the significance of the acceleration derivatives, indicated that inclusion of the measured derivatives in the equations of motion lengthened the period of the lateral oscillation by 10 percent for a typical delta-wing airplane and increased the time to damp to one-half amplitude by 50 percent.

Fisher, Lewis R.↗
NASA NTRS1994

Comparison of full-scale, small-scale, and CFD results for F/A-18 forebody slot blowing

It has been shown experimentally that forebody flow control devices provide a significant increase in yaw control for fighter aircraft at high angle-of-attack. This study presents comparisons of the various experimental and computational results for tangential slot blowing on the F/A-18 configuration. Experimental results are from the full-scale and 6 percent-scale model test and computational solutions are from both isolated forebody and and full aircraft configurations. The emphasis is on identifying trends in the variation of yawing moment with blowing-slot exit conditions. None of the traditional parameters (mass flow ratio, blowing momentum coefficient, velocity ratio) succeeded in collapsing all of the results into a common curve. Several factors may effect the agreement between the 6 percent- and full-scale results including Reynolds number effects, sensitivity of boundary layer transition from laminar to turbulent flow, and poor geometric fidelity, particularly of the blowing slot. The disagreement between the full-scale and computed yawing moments may be due to a mismatch in the slot exit conditions for the same mass flow ratio or aircraft configuration modeling. The general behavior of slot blowing on the 6 percent-scale and computational models is correct, but neither matches the full-scale results.

Lanser, Wendy R.↗
NASA NTRS1981

Comparison of upwind and downwind rotor operations of the DOE/NASA 100-kW Mod-O wind turbine

Three aspects of the test results are compared: rotor blade bending loads, rotor teeter response, and nacelle yaw moments. As a result of the tests, it is shown that while mean flatwise bending moments were unaffected by the placement of the rotor, cyclic flatwise bending tended to increase with wind speed for the downwind rotor while remaining somewhat uniform with wind speed for the upwind rotor, reflecting the effects of increased flow disturbance for a downwind rotor. Rotor teeter response was not significantly affected by the rotor location relative to the tower, but appears to reflect reduced teeter stability near rated wind speed for both configurations. Teeter stability appears to return above wind speed, however. Nacelle yaw moments are higher for the upwind rotor but do not indicate significant design problems for either configuration.

Glasgow, J. C.↗
NASA NTRS1981

Comparison of upwind and downwind rotor operation of the DOE/NASA 100-kW MOD-0 wind turbine

Tests were conducted on a 38m diameter horizontal axis wind turbine, which had first a rotor downwind of the supporting truss tower and then upwind of the tower. Aside from the placement of the rotor and the direction of rotation of the drive train, the wind turbine was identical for both tests. Three aspects of the test results are compared: rotor blade bending loads, rotor teeter response, and nacelle yaw moments. As a result of the tests, it is shown that while mean flatwise bending moments were unaffected by the placement of the rotor, cyclic flatwise bending tended to increase with wind speed for the downwind rotor while remaining somewhat uniform with wind speed for the upwind rotor, reflecting the effects of increased flow disturbance for downwind rotor. Rotor teeter response was not significantly affected by the rotor location relative to the tower, but appears to reflect reduced teeter stability near rated wind speed for both configurations. Teeter stability appears to return above rated wind speed, however. Nacelle yaw moments are higher for the upwind rotor but do not indicate significant design problems for either configuration.

Glasgow, J. C.↗
NASA NTRS1972

Asymmetric lateral-directional characteristics of pointed bodies of revolution at high angles of attack

A low-speed wind-tunnel investigation was conducted in order to determine the cause of asymmetric yawing moments produced by long pointed fuselage nose shapes at high angles of attack. Force tests were conducted with a cone, tangent-ogive model, and a paraboloid of revolution over a range of Reynolds numbers from 0.15 million to 0.35 million for an angle-of-attack range from 0 deg to 75 deg and an angle-of-sideslip range of plus or minus 30 deg. Tuft and smoke flow-visualization tests were also conducted to aid in the analysis. Large asymmetric yawing moments were obtained for the cone and tangent-ogive body at high angles of attack (of the order of 40 to 60 deg). These large moments were caused by asymmetric shedding of vortex sheets off the long pointed nose. The asymmetric moments could be eliminated by use of symmetrically arranged strikes on the nose. The paraboloid of revolution did not produce a strong asymmetric flow field at high angles of attack and did not exhibit asymmetric moments.

Coe, P. L., Jr.↗
NASA NTRS1994

Numerical analysis of tangential slot blowing on a generic chined forebody

A numerical study is performed to investigate the effects of tangential slot blowing on a generic chined forebody. The Reynolds-averaged, thin-layer, Navier-Stokes equations are solved to obtain the high-angle-of-attack viscous flow field about a generic chined forebody. Tangential slot blowing is investigated as a means of forebody flow control to generate side force and yawing moment on the forebody. The effects of jet mass flow ratios, angle of attack, and blowing slot location in the axial and circumferential directions are studied. The computed results are compared with available wind tunnel experimental data. The solutions with and without blowing are also analyzed using helicity density contours, surface flow patterns, and off-surface instantaneous streamlines. The results of this analysis provide details of the flow field about the generic chined forebody, as well as show that tangential slot blowing can be used as a means of forebody flow control to generate side force and yawing moment.

Agosta, Roxana M.↗
NASA NTRS1995

Computational analysis of forebody tangential slot blowing on the high alpha research vehicle

A numerical analysis of forebody tangential slot blowing as a means of generating side force and yawing moment is conducted using an aircraft geometry. The Reynolds-averaged, thin-layer, Navier-Stokes equations are solved using a partially flux-split, approximately-factored algorithm. An algebraic turbulence model is used to determine the turbulent eddy viscosity values. Solutions are obtained using both patched and overset grid systems. In the patched grid model, and actuator plane is used to introduce jet variables into the flow field. The overset grid model is used to model the physical slot geometry and facilitate modeling of the full aircraft configuration. A slot optimization study indicates that a short slot located close to the nose of the aircraft provided the most side force and yawing moment per unit blowing coefficient. Comparison of computed surface pressure with that obtained in full-scale wind tunnel tests produce good agreement, indicating the numerical method and grid system used in the study are valid. Full aircraft computations resolve the changes in vortex burst point due to blowing. A time-accurate full-aircraft solution shows the effect of blowing on the changes in the frequency of the aerodynamic loads over the vertical tails. A study of the effects of freestream Mach number and various jet parameters indicates blowing remains effective through the transonic Mach range. An investigation of the force onset time lag associated with forebody blowing shows the lag to be minimal. The knowledge obtained in this study may be applied to the design of a forebody tangential slot blowing system for use on flight aircraft.

Gee, Ken↗
NASA NTRS1994

F/A-18 forebody vortex control. Volume 1: Static tests

A wind tunnel test was conducted on a six percent model of the F/A-18 at the NASA Ames 7 X 10-Foot Low Speed Wind Tunnel. The primary objective of the test was to evaluate several forebody vortex control configurations at high angles of attack in order to determine the most effective method of obtaining well behaved yawing moments, in preparation for the rotary balance test. Both mechanical and pneumatic systems were tested. Single and dual rotating nose tip strakes and a vertical nose strake were tested at different sizes and deflections. A series of jet blowing configurations were located at various fuselage stations, azimuth angles, and pointing angles ranging from straight aft to 60 deg canted inboard. Slot blowing was investigated for several slot lengths and fuselage stations. The effect of blowing rate was tested for both of these pneumatic systems. The most effective configurations were then further tested with a variation of both sideslip angle and Reynolds number over a range of angles of attack from 0 to 60 deg. It was found that a very robust system can be developed that provides yawing moments at angles of attack up to 60 deg that significantly exceeds that available from 30 deg of rudder deflection (F/A-18 maximum) at 0 deg angle of attack.

Kramer, Brian R.↗
NASA NTRS1974

Aerodynamic roll damping of a T-tail transport configuration

The aerodynamic roll damping and the yawing moment due to roll rate for a model of a T-tail transport with aft-mounted engines were measured by means of a small-amplitude forced-oscillation mechanism. The tests were made for Mach numbers between 0.21 and 0.80 over a range of angles of attack from about minus 4 deg to 22 deg. The basic configuration had positive damping in roll at low angles of attack with regions of low positive and negative damping for angles of attack above 8 deg to 10 deg. There was good agreement between the theoretical estimates of the roll damping for the wing alone and the experimental results at an angle of attack of 0 deg for Mach numbers of 0.60 and less. The T-tail configuration and the engine nacelles mounted aft on the fuselage did not significantly affect either the damping in roll or the yawing moment due to roll rate.

Boyden, R. P.↗
NASA NTRS1932

Pressure Distribution Over the Fuselage of a PW-9 Pursuit Airplane in Flight

This report presents the results obtained from pressure distribution tests on the fuselage of a PW-9 pursuit airplane in a number of conditions of flight. The investigation was made to determine the contribution of the fuselage to the total lift in conditions considered critical for the wing structure, and also to determine whether the fuselage loads acting simultaneously with the maximum tail loads were of such a character as to be of concern with respect to the structural design of other parts of the airplane. The results show that the contribution of the fuselage toward the total lift is small on this airplane. Aerodynamic loads on the fuselage are, in general, unimportant from the structural viewpoint, and in most cases they are of such character that, if neglected, a conservative design results. In spins, aerodynamic forces on the fuselage produce diving moments of appreciable magnitude and yawing moments of small magnitude, but opposing the rotation of the airplane. A table of cowling pressures for various maneuvers is included in the report.

Rhode, Richard V↗
NASA NTRS1951

Aerodynamic Characteristics of a Flying-Boat Hull Having a Length-Beam Ratio of 15, TED No. NACA 2206

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

Riebe, John M.↗