Search NASA⌕ Search

SEARCH · Search NASA

Results for “Zirconate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of CMAS viscosity on the infiltration depth in thermal barrier coatings of different microstructures

Calcium magnesium aluminum silicate (CMAS) is one of the leading concerns for the gas turbine industry. The effects of CMAS viscosity and the coating microstructure on CMAS infiltration depth were explored by conducting a time dependent interaction study. Three CMAS compositions were used from literature, and their viscosities predicted through FactSage viscosity module were drastically different. The interaction was carried out on three different TBCs synthesized using the solution precursor plasma spray process (SPPS): two of the TBCs were made of yttrium aluminum garnet (YAG) having different microstructures that promote different modes of CMAS infiltration, and one TBC was made of gadolinium zirconate (GZO). All samples had stress relieving vertical cracks and different intensities of horizontally banded porosity, (inter pass boundaries IPBs). A concentration of 100 mg/cm 2 of CMAS was applied on the TBCs which were then subjected to a 5-minute interaction at 1300 °C. Samples were analyzed using scanning electron microscopy (SEM), electron dispersive X-ray spectroscopy (EDXS), and transmission electron microscopy (TEM). Low viscosity CMAS readily penetrated the TBCs while more viscous CMAS showed less penetration. The depth of CMAS infiltration depended on the coating microstructure. In the YAG with IPBs, the CMAS spread horizontally in the IPBs before infiltrating deeper, resulting in reduced infiltration depth compared to other samples in spite of having wider vertical cracks. TEM and EDXS analysis were performed to investigate the phases present in the CMAS-TBC interaction region in YAG. Two regions were chosen, the top TBC surface in direct contact with the sea of CMAS, and the region at the CMAS penetration ended within the coating. Finally, the results showed that no secondary phases like apatite were observed in YAG, thus it can be concluded that the arrest of CMAS happened solely because of CMAS viscosity and the short infiltration time.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chemical Speciation and Stability of Uranium in Unconventional Shales: Impact of Hydraulic Fracture Fluid

Uranium and other radionuclides are prominent in many unconventional oil/gas shales and is a potential contaminant in flowback/produced waters due to the large volumes/types of chemicals injected into the subsurface during stimulation. In this work, to understand the stability of U before and after stimulation, a geochemical study of U speciation was carried out on three shales (Marcellus, Green River, and Barnett). To do so, two types of samples for each shale were subjected to sequential chemical extractions: unreacted and shale-reacted with a synthetic hydraulic fracture fluid. Furthermore, a significant proportion of the total U (20–57%) was released from these three shales after reaction with fracture fluid, indicating that U is readily leachable. The total U released exceeds labile water-soluble and exchangeable fractions in unreacted samples, indicating that fluids leach more recalcitrant phases in the shale. Radiographic analysis of unreacted Marcellus shale thin sections shows U associated with detrital quartz and the clay matrix in the shale. Detrital zircon and TiO2 identified by an electron microprobe could account for the hot spots. This study shows that significant proportions of U in three shales are mobile upon stimulation. In addition, the extent of mobilization of U depends on the U species in these rocks.

58 GEOSCIENCES↗
DOE OSTI2021

The Role of Water and Hydroxyl Groups in the Structures of Stetindite and Coffinite, MSiO 4 (M = Ce, U)

Orthosilicates adopt the zircon structure types ( I 4 1 /amd ), consisting of isolated SiO 4 tetrahedra joined by A-site metal cations, such as Ce and U. They are of significant interest in the fields of geochemistry, mineralogy, nuclear waste form development, and material science. Stetindite (CeSiO 4 ) and coffinite (USiO 4 ) can be formed under hydrothermal conditions despite both being thermodynamically metastable. Water has been hypothesized to play a significant role in stabilizing and forming these orthosilicate phases, though little experimental evidence exists. To understand the effects of hydration or hydroxylation on these orthosilicates, in situ high-temperature synchrotron and laboratory-based X-ray diffraction was conducted from 25 to ~850 °C. Stetindite maintains its I 4 1 /amd symmetry with increasing temperature but exhibits a discontinuous expansion along the a- axis during heating, presumably due to the removal of water confined in the [001] channels, which shrink against thermal expansion along the a -axis. Furthermore, additional in situ high-temperature Raman and Fourier transform infrared spectroscopy also confirmed the presence of the confined water. Coffinite was also found to expand nonlinearly up to 600 °C and then thermally decompose into a mixture of UO 2 and SiO 2 . A combination of dehydration and dehydroxylation is proposed for explaining the thermal behavior of coffinite synthesized hydrothermally. Additionally, we investigated high-temperature structures of two coffinite-thorite solid solutions, uranothorite (U x Th 1– x SiO 4 ), which displayed complex variations in composition during heating that was attributed to the negative enthalpy of mixing. Lastly, for the first time, the coefficients of thermal expansion of CeSiO 4 , USiO 4 , U 0.46 Th 0.54 SiO 4 , and U 0.9 Th 0.1 SiO 4 were determined to be α V = 14.49 × 10 –6 , 14.29 × 10 –6 , 17.21 × 10 –6 , and 17.23 × 10 –6 °C –1 , respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Coupled Chemical and Mechanical Control of Phase Stability in Lanthanide-Substituted BiVO 4

Doping is widely used to enhance the photoelectrochemical performance of BiVO 4 , yet solubility limits and polymorphic stability constrain compositional tuning. Here, in this study, the role of trivalent cation substitution (Ln = La, Nd, Dy, Ho, Y) on pressure-induced phase transformations in Bi 1–x Ln x VO 4 (x ≤ 0.5) is described. Powder X-ray and neutron diffraction reveal that increasing Ln content stabilizes the tetragonal zircon-type polymorph under ambient conditions, while applied pressures of up to ∼5 GPa promote conversion to the monoclinic fergusonite-type polymorph. In-situ neutron diffraction on Bi 0.8 La 0.2 VO 4 shows a reversible monoclinic to tetragonal transition near 2–3 GPa with a bulk modulus of 147 GPa. The extent of conversion depends strongly on dopant identity, concentration, and synthetic route, with mixed-phase solid-state samples converting more efficiently than phase-pure coprecipitated materials. These results demonstrate pressure as a viable pathway to access metastable, doped BiVO 4 compositions beyond conventional solubility limits.

Sypkes, Kathryn I. [University of Sydney, NSW (Aus↗
DOE OSTI2024

Superior Piezo-/Ferro-Electricity in Antiferroelectric Ag x NbO 3-δ Thin Films by Nanopillar Local Structure Design

Antiferroelectrics are fundamental mother compounds critical in developing innovative lead-free piezoelectrics and ferroelectrics and hold great promise for wide-ranging applications in energy conversion and electronic devices. However, harnessing their superior properties presents a significant challenge due to the delicate balance required between their various states. Here, in this study, through the unique design of nanopillar structures to alleviate the local polar heterogeneity, we have achieved significantly improved piezo-/ferro-electricity in classic lead-free antiferroelectric Ag x NbO 3-δ (x = 1, 0.9, and 0.8) epitaxial thin films. The effective piezoelectric coefficient reaches 440 pm V –1 , 1 order of magnitude larger than the stoichiometric AgNbO 3 , rivaling classic lead zirconate titanate piezoelectrics. Atomic-scale electron microscopy investigations unravel the underlying mechanisms. The nanopillars, characterized by antisite occupancy of both Ag and Nb atoms and forming out-of-phase boundaries with the matrix, reduce the local crystal symmetry via interphase strain. This leads to the creation of flexible multinanodomain structures that significantly facilitate polarization rotation, thus substantially enhancing the piezoelectric performance. This study demonstrates the feasibility of engineering local heterogeneity through nanopillar design, offering a generally applicable method for property improvement of a wide range of antiferroelectrics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Scalable Surface Micro-Texturing of LLZO Solid Electrolytes for Battery Applications

A challenge for lithium lanthanum zirconate (LLZO)-based solid-state batteries is to increase the critical current density (CCD) to enable high current cycling. A promising strategy is to modify the LLZO surface morphology to provide a larger contact area with the Li metal. Here, a surface-textured thin LLZO electrolyte was prepared through an easily scalable process. The texturing process is a simple pressing of green LLZO tapes between micro-textured substrates. A variety of textures can be produced, depending on the type of substrate, and texturing can be on either one side or both sides. For this work, after pressing and sintering, several micro-patterns are formed on thin LLZO (~118 μm thick). The properties of the various samples were characterized to investigate the impact of surface texturing, and the most promising ones were selected for electrochemical testing in symmetrical lithium cells and full cells. Li symmetric cells using a coarse ridge-textured LLZO exhibit ~2.5 times increased CCD compared to planar non-textured LLZO, and a solid-state full cell shows stable cycling and improved rate performance. Finally, we believe this process offers a favorable trade-off of processing complexity vs structural optimization to maximize CCD.

25 ENERGY STORAGE↗
DOE OSTI2024

eReaxFF force field development for BaZr 0.8 Y 0.2 O 3-δ solid oxide electrolysis cells applications

The use of solid-oxide materials in electrocatalysis applications, especially in hydrogen-evolution reactions, is promising. However, further improvements are warranted to overcome the fundamental bottlenecks to enhancing the performance of solid-oxide electrolysis cells (SOECs), which is directly linked to the more-refined fundamental understanding of complex physical and chemical phenomena and mass exchanges that take place at the surfaces and in the bulk of electrocatalysis materials. Here, we developed an eReaxFF force field for barium zirconate doped with 20 mol% of yttrium, BaZr 0.8 Y 0.2 O 3-δ (BZY20) to enable a systematic, large-length-scale, and longer-timescale atomistic simulation of solid-oxide electrocatalysis for hydrogen generation. All parameters for the eReaxFF were optimized to reproduce quantum-mechanical (QM) calculations on relevant condensed phase and cluster systems describing oxygen vacancies, vacancy migrations, electron localization, water adsorption, water splitting, and hydrogen generation on the surfaces of the BZY20 solid oxide. Using the developed force field, we performed both zero-voltage (excess electrons absent) and non-zero-voltage (excess electrons present) molecular dynamics simulations to observe water adsorption, water splitting, proton migration, oxygen-vacancy migrations, and eventual hydrogen-production reactions. Based on investigations offered in the present study, we conclude that the eReaxFF force field-based approach can enable computationally efficient simulations for electron conductivity, electron leakage, and other non-zero-voltage effects on the solid oxide materials using the explicit-electron concept. Moreover, we demonstrate how the eReaxFF force field-based atomistic-simulation approach can enhance our understanding of processes in SOEC applications and potentially other renewable-energy applications.

08 HYDROGEN↗
DOE OSTI2020

Large electromechanical strain and unconventional domain switching near phase convergence in a Pb-free ferroelectric

In many ferroelectrics, large electromechanical strains are observed near regions of composition- or temperature- driven phase coexistence. Phenomenologically, this is attributed to easy re-orientation of the polarization vector and/or phase transition, although their effects are highly convoluted and difficult to distinguish experimentally. Here, we used synchrotron X-ray scattering and digital image correlation to differentiate between the microscopic mechanisms leading to large electrostrains in an exemplary Pb-free piezoceramic Sn-doped barium calcium zirconate titanate. Large electrostrains of ~0.2% measured at room-temperature are attributed to an unconventional effect, wherein polarization switching is aided by a reversible phase transition near the tetragonal-orthorhombic phase boundary. Additionally, electrostrains of ~0.1% or more could be maintained from room temperature to 140°C due to a succession of different microscopic mechanisms. In situ X-ray diffraction elucidates that while 90° domain reorientation is pertinent below the Curie temperature ( T C ), isotropic distortion of polar clusters is the dominant mechanism above T C .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Investigation of MgO additives on microstructure and properties of thin LLZO electrolytes for all-solid-state batteries

To realize high-energy density lithium lanthanum zirconate (LLZO)-based solid-state batteries (SSB), LLZO electrolytes should be fabricated with low thickness and high mechanical strength. An effective strategy for strengthening ceramic materials is to use additives. Here, we employed MgO nanopowders and fibers as additives for the thin LLZO electrolyte in order to improve the mechanical strength. The microstructure, mechanical properties, and electrochemical properties are characterized to investigate the effects of adding MgO and sintering time. The MgO remains at grain boundaries after sintering, making the microstructure of LLZO fine and uniform. The mechanical strength of the MgO-added LLZO was enhanced by more than 60% while maintaining high ionic conductivity (1 × 10 -4 S cm -1 ) at room temperature. Li symmetric cells using the MgO fiber–LLZO and MgO powder–LLZO exhibit 2 and 3 times higher critical current density (CCD) than those of pure LLZO, and a solid-state full cell exhibits stable cycling performance. Further, these results demonstrate that the use of MgO nanopowder or fiber as an additive for thin LLZO is beneficial for high-current density cycling, by improving mechanical properties and microstructure.

25 ENERGY STORAGE↗
DOE OSTI2020

On the role of the zirconia/ceria interface in the degradation of solid oxide electrolysis cells

Gd-doped Ceria (GDC) barrier layers are widely used in solid oxide electrolysis cells to prevent reactions between the Y-stabilized Zirconia (YSZ) electrolyte and oxygen electrode. In some cases, electrolysis operation causes fracture near the GDC/YSZ interface. Here, we explain this effect using a numerical calculation, showing that a peak oxygen pressure is observed near the GDC/YSZ interface during electrolysis operation. Moreover, GDC/YSZ interdiffusion and possible zirconate phase formation occurring during electrode firing yield a low oxygen ion conductivity region that introduces a much higher peak oxygen partial pressure at the interdiffusion layer/YSZ interface, thereby exacerbating degradation. The results indicate that the peak pressure can be reduced and, thereby, damage can be mitigated by altering processing in order to minimize interdiffusion, decreasing the GDC layer thickness, and reducing oxygen electrode polarization resistance or altering electrolyte transport properties, e.g., changing the Gd doping level of GDC to increase the oxygen vacancy diffusivity.

Physics↗
DOE OSTI2022

Piezoelectric property of PZT nanofibers characterized by resonant piezo-force microscopy

Nano-piezoelectric materials have drawn tremendous research interest. However, characterization of their piezoelectric properties, especially measuring the piezoelectric strain coefficients, remains a challenge. Normally, researchers use an AFM-based method to directly measure nano-materials’ piezoelectric strain coefficients. But, the extremely small piezoelectric deformation, the influence from the parasitic electrostatic force, and the environmental noise make the measurement results questionable. In this paper, a resonant piezo-force microscopy method was used to accurately measure the piezoelectric deformation from 1D piezoelectric nanofibers. During the experiment, the AFM tip was brought into contact with the piezoelectric sample and set to work at close to its first resonant frequency. A lock-in amplifier was used to pick up the sample’s deformation signal at the testing frequency. By using this technique, the piezoelectric strain constant d 33 of the Lead Zirconate Titanate (PZT) nanofiber with a diameter of 76 nm was measured. The result showed that d 33 of this PZT nanofiber was around 387 pm/V. Meanwhile, by tracking the piezoelectric deformation phase image, domain structures inside PZT nanofibers were identified.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulating the non-monotonic strain response of nanoporous multiferroic composites under electric field control

In this work, we simulate and analyze the mechanical response of a class of multiferroic materials consisting of a templated porous nanostructure made out of cobalt ferrite (CFO) partially filled by atomic layer deposition (ALD) with a ferroelectric phase of lead zirconate titanate (PZT). The strain in the device is measured when an electric field is applied for varying ALD thicknesses, displaying a non-monotonic dependence with a maximum strain achieved for a coating thickness of 3 nm. To understand this behavior, we apply finite element modeling to the smallest repeatable unit of the nanoporous template and simulate the mechanical response as a function of PZT coating thickness. We find that this non-monotonic response is caused by the interplay between two driving forces opposing one another. First, increased porosity works toward increasing the strain due to a reduced system stiffness. Second, decreased porosity involves a larger mass fraction of PZT, which drives the electro-mechanical response of the structure, thus leading to a larger strain. The balance between these two driving forces is controlled by the shear coupling at the CFO/PZT interface and the effective PZT cross section along the direction of the applied electric field. Here, our numerical results show that considering a nonlinear piezoelectric response for PZT leads to an improved agreement with the experimental data, consistent with ex situ poling of the nanostructure prior to magnetic measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Strain transfer in porous multiferroic composites of CoFe 2 O 4 and PbZr x Ti 1- x O 3

This manuscript examines the mechanism of strain-coupling in a multiferroic composite of mesoporous cobalt ferrite (CFO), conformally filled with lead zirconate titanate (PZT). We find that when the composites are electrically poled, remanent strain from the piezoelectric PZT layer can be transferred to the magnetostrictive CFO layer. X-ray diffraction shows that this strain transfer is greatest in the most porous samples, in agreement with magnetometry measurements, which show the greatest change in sample saturation magnetization in the most porous samples. In conclusion, strain analysis shows that porosity both accommodates greater lattice strain and mitigates the effects of substrate clamping in thin film strain-coupled composites.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

New dynamic diamond anvil cell for time-resolved radial x-ray diffraction

The dynamic diamond anvil cell (dDAC) is a recently developed experimental platform that has shown promise for studying the behavior of materials at strain rates ranging from intermediate to quasi-static and shock compression regimes. Combining dDAC with time-resolved x-ray diffraction (XRD) in the radial geometry (i.e., with incident x-rays perpendicular to the axis of compression) enables the study of material properties such as strength, texture evolution, and deformation mechanisms. This work describes a radial XRD dDAC setup at beamline P02.2 (Extreme Conditions Beamline) at DESY’s PETRA III synchrotron. Time-resolved radial XRD data are collected for titanium, zirconium, and zircon samples, demonstrating the ability to study the strength and texture of materials at compression rates above 300 GPa/s. In addition, the simultaneous optical imaging of the DAC sample chamber is demonstrated. The ability to conduct simultaneous radial XRD and optical imaging provides the opportunity to characterize plastic strain and deviatoric strain rates in the DAC at intermediate rates, exploring the strength and deformation mechanisms of materials in this regime.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Development of an ultraprecise glue-free bimorph deformable mirror with a length of 460 mm

Lead zirconate titanate (PZT) bimorph mirrors are essential for performing multiple functions, such as beam shaping, wavefront correction, and dynamic focusing with adjustable beam sizes. They typically consist of a mirror substrate with PZT electrodes bonded to the substrate using a thin epoxy film. However, glue-bonded PZT mirrors exhibit low reproducibility in measurement results. One source of this variability is water absorption by the substrate’s epoxy adhesive during wet fabrication processes, such as elastic emission machining (EEM), which leads to swelling and deformation. Additionally, longer deformable bimorph mirrors require larger PZT electrodes, further complicating their design and fabrication, particularly during bonding and ultraprecise metrology. To address these challenges, silver nanoparticles were employed to bond PZT elements to the silicon (Si) mirror, eliminating the need for epoxy glue. Here, in this study, we developed an inorganic-glue-free PZT bimorph mirror with a length of 460 mm and 28 channels. The glue-free bonding method successfully ensured the high reproducibility of measurements after water immersion. This approach resulted in a shape error of only 0.41 nm root mean square after the figure correction process using an ultraprecise EEM process. Scanning acoustic tomography and basic response function tests confirmed the success of the bonding process, showing no critical voids. Furthermore, the shape changes induced by applying voltages to the PZT electrodes closely matched predictions obtained from simulations. These results demonstrate the reliability and precision of the proposed glue-free bonding technique, paving the way for improved performance of new PZT bimorph mirrors.

Ichii, Yoshio [SLAC National Accelerator Laborator↗
DOE OSTI2025

Completion of lunar magma ocean solidification at 4.43 Ga

Crystallization of the lunar magma ocean yielded a chemically unique liquid residuum named KREEP. This component is expressed as a large patch on the near side of the Moon and a possible smaller patch in the northwest portion of the Moon’s South Pole-Aitken basin on the far side. Thermal models estimate that the crystallization of the lunar magma ocean (LMO) could have spanned from 10 and 200 My, while studies of radioactive decay systems have yielded inconsistent ages for the completion of LMO crystallization covering over 160 My. Here, we show that the Moon achieved >99% crystallization at 4,429 ± 76 Ma, indicating a lunar formation age of ~4,450 Ma or possibly older. Using the 176 Lu– 176 Hf decay system (t 1/2 = 37 Gy), we found that the initial 176 Hf/ 177 Hf ratios of lunar zircons with varied U–Pb ages are consistent with their crystallization from a KREEP-rich reservoir with a consistently low 176 Lu/ 177 Hf ratio of 0.0167 that emerged ~140 My after solar system formation. The previously proposed younger model age of ~4.33 Ga for the source of mare basalts (240 My after solar system formation) might reflect the timing of a large impact. Our results demonstrate that lunar magma ocean crystallization took place while the Moon was still battered by planetary embryos and planetesimals leftover from the main stage of planetary accretion. The study of Lu–Hf model ages for samples brought back from the South Pole-Aitken basin will help to assess the lateral continuity of KREEP and further understand its significance in the early history of the Moon.

Science & Technology - Other Topics↗
DOE OSTI2021

A mini-review on proton conduction of BaZrO 3 -based perovskite electrolytes

Abstract Proton conducting ceramics show promise in fuel cells, electrolyzers, permeation membranes, sensor applications, and membrane reactors. Among several types of materials that exhibit proton conduction, perovskite oxides show high proton conductivity at intermediate temperatures, presenting potential benefits for long-term use and lower costs for energy applications. Doped barium zirconate, BaZrO 3 , is a material that has shown high proton conductivity with encouraging chemical stability. Therefore, it is considered a promising material especially for proton-conducting solid oxide electrochemical cells. Although the proton conduction of doped BaZrO 3 has been extensively characterized, the specific phenomena behind its proton conduction are not fully understood. Only recently have specialized techniques and computational tools begun to elucidate the phenomena that determine the conduction properties of the material. In this mini review, an evaluation of the factors affecting the proton conductivity of doped BaZrO 3 perovskites and the phenomena governing variations in proton concentration and mobility are presented. Special attention is given to proton interactions with dopants and their resulting effect on hydration and transport properties. Technical strategies are provided to give some guidance on the development of protonic ceramics in energy conversion applications.

08 HYDROGEN↗
DOE OSTI2022

Faradaic efficiency in protonic-ceramic electrolysis cells

Abstract Proton-conducting ceramics (e.g. doped barium zirconates or cerates) are typically mixed ionic-electronic conductors (MIECs). The electronic conduction, typically in the form of positively charged small polarons or electron holes, leads to ‘electronic leakage.’ In an ideal steam-electrolysis cell, one gas-phase H 2 molecule is produced from every two electrons delivered from an external power source. In other words, such ideal behavior achieves 100% faradaic efficiency. However, the electronic flux associated with MIEC membranes contributes to reduced faradaic efficiency. The present paper develops a model that predicts the behavior of faradaic efficiency as a function of electrolysis-cell operating conditions. Although the model framework is more general, the paper focuses on the behavior of a cell based upon a BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3 − δ (BCZYYb) membrane. The study predicts the effects of operating conditions, including temperature, pressure, and gas compositions.

Zhu, Huayang↗