Search NASA⌕ Search

SEARCH · Search NASA

Results for “aerodynamic drag”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

The Minimum Induced Drag of Aerofoils

Equations are derived to demonstrate which distribution of lifting elements result in a minimum amount of aerodynamic drag. The lifting elements were arranged (1) in one line, (2) parallel lying in a transverse plane, and (3) in any direction in a transverse plane. It was shown that the distribution of lift which causes the least drag is reduced to the solution of the problem for systems of airfoils which are situated in a plane perpendicular to the direction of flight.

Munk, M. M.↗

"Coulombic Viscosity" In Granular Materials: Planetary and Astrophysical Implications

The term "Coulombic viscosity" is introduced here to define an empirically observed phenomenon from experiments conducted in both microgravity, and in ground-based 1-g conditions. In the latter case, a sand attrition device was employed to test the longevity of aeolian materials by creating two intersecting grain-circulation paths or cells that would lead to most of the grain energy being expended on grain-to-grain collisions (simulating dune systems). In the areas in the device where gravitationally-driven grain-slurries recycled the sand, the slurries moved with a boundary-layer impeded motion down the chamber walls. Excessive electrostatic charging of the grains during these experiments was prevented by the use of an a.c. corona (created by a Tesla coil) through which the grains passed on every cycle. This created both positive and negative ions which neutralized the triboelectrically-generated grain charges. When the corona was switched on, the velocity of the wall-attached slurries increased by a factor of two as approximately determined by direct observation. What appeared to be a freely-flowing slurry of grains impeded only by intergranular mechanical friction, had obviously been significantly retarded in its motion by electrostatic forces between the grains; with the charging reduced, the grains were able to move past one another without a flow "viscosity" imposed by the Coulombic intergranular forces. A similar phenomenon was observed during microgravity experiments aboard Space Shuttle in USML-1 & USML-2 spacelabs where freely-suspended clouds of sand were being investigated for their potential to for-m aggregates. In this environment, the grains were also charged electrostatically (by natural processes prior to flight), but were free from the intervention of gravity in their interactions. The grains were dispersed into dense clouds by bursts of air turbulence and allowed to form aggregates as the ballistic and turbulent motions damped out. During this very brief (30-60 sec) damping period, motion of the grains was observed to be retarded by the electrostatic interactions. The fact that the grains almost instantly formed aggregates was evidence that their ballistic motions had been constrained and redirected by the dipole-dipole interactions that led to filamentary aggregate development. Undoubtedly, the "Coulombic viscosity" of the cloud assisted in damping grain motion so rapidly. The electrostatically-induced grain-cloud viscosity or drag exerted on grain motion, is a complex function of three major parameters: charge magnitude, charge sign, and mean intergranular distance. The above experiments illustrate one particular type of granular behavior. The discussion here will therefore be restricted to drag relationships: (a) between grains that are naturally charged triboelectrically and thus exhibit dipole-dipole attractions between one another even if there are slight net charges present (which can be overwhelmed by dipole coupling at short distances), and (b) between grains that are densely spaced where the intergranular distance varies between zero and some value (usually tens or hundreds of grain diameters) that permits each grain to detect the dipole moment of another grain -- the distance is not so great that other grains appears as neutral electrical "singularities. I. Aeolian transport: During motion of grains in a saltation cloud (on Earth, Mars, or Venus), triboelectric charging must occur as a result of multiple grain contacts, and by friction with the entraining air. A situation might develop that is similar to the one described above in the attrition device: grain motion becoming significantly retarded (reduced flux) as grains find it increasingly difficult to either separate from the surface, or to pass one another without Coulombic retarding forces. A "Coulombic drag" will exist at flux initiation and increase with time to work in direct opposition to the aerodynamic drag that drives the grain motion. It is predicted that this will lead to an increase with time of both the aerodynamic and bed-dilatancy thresholds (3). Because of Paschen discharge effects in the martian atmosphere, the electrostatic charging in a saltation cloud may be partially abated, but this will lead to greater grain mobility, more charging, and thus to a charge-discharge steady state mediated by mechanical interactions. II. Dry colluvial systems: Sand avalanches on dunes, dry debris flows, talus flows, avalanches, and pyroclastic surges are examples of gravity-driven, dense granular flows where rock/grain fragmentation and grain-to-grain interactions cause triboelectrification (sometimes augmented by other electrical charging processes), and where the grain densities of the systems are such that strong dipole-dipole interactions between grains might be expected to be present. Because it is expected that the Coulombic forces between grains will cause a sluggishness or enhanced granular-flow viscosity, the motion of a grain mass will be retarded or damped so that this will assist, ultimately, in terminating the flow. The greatest Coulombic viscosity will be created in the most highly charged systems, which will also be the most energetic. Thus, grain flows have some tendency to be self-limiting by internal energy partitioning; gravitational potential is converted to Coulombic potential, which manifests itself as a drag force between the grains. III. Volcanic eruption plumes and impact ejecta curtains: The violence of these systems leads to powerful electrical charging of particulates. Lightning storms emanating from volcanic plumes are a testimony to the levels of charging. As pyroclastic grains interact forcefully and frequently within eruption plumes, it is reasonable to predict that the internal turbulent motions of the plume will be significantly damped by the Coulombic viscosity exerted by grain charges. Additional information is contained in the original.

Marshall, J. R.↗

Estimating Drag and Heating Coefficients for Hollow Reentry Objects in Transitional Flow Using DSMC

In NASA’s Object Reentry Survival Analysis Tool (ORSAT), aerodynamic drag and aerothermal heating coefficients are computed for each of the free-molecular, continuum, and transitional flow regimes using analytical and semi-analytical methods. These methods are typically limited to convex, blunt objects (such as spheres) and are applied to other objects such as boxes and cylinders using multiplicative “shape factors” to account for the different behavior. Previous literature has analyzed the aerodynamic and aerothermodynamic properties of flow around sharp-edged objects like boxes and cylinders in transitional flow, though only those objects with solid external boundaries. However, many reentry objects we have encountered in real spacecraft have been hollow (i.e., with the potential to allow flow through them). We present here preliminary results from analyses performed using the NASA Direct Simulation Monte Carlo (DSMC) Analysis Code (DAC) on hollow cylinders and boxes (with varying wall thickness-diameter ratio).

Marichalar, Jeremiah J.↗

Dynamics of Drag Free Formations in Earth Orbit

In this paper the translational equations of motion of a formation of n spacecraft in Earth orbit, n(sub f) of which are drag-free spacecraft, are derived in a coordinate-free manner using the balance of linear momentum and direct tensor notation. A drag-free spacecraft consists of a spacecraft bus and a proof mass shielded from external disturbances in an internal cavity. By controlling the spacecraft so that the proof mass remains centered in the cavity, the spacecraft follows a purely gravitational orbit. The results described in this paper provide a first step toward coupling drag-free control technology with formation flying in order to mitigate the effect of differential aerodynamic drag on formation flying missions (e.g., Earth imaging applications) in low Earth orbit.

drag-free technology↗

High Reynolds Number Predictions for the Baseline Arrow Wing at Mach 2.48

The NASA High Speed Research (HSR) Program is intended to establish a technology base enabling industry development of an economically viable and environmentally acceptable second generation high speed civil transport (HSCT). The objective of the Configuration Aerodynamics task of the program is the development of aerodynamic drag reduction, stability and control, and propulsion airframe integration technologies required to support the HSCT development process. Aerodynamic design tools are being developed, evaluated, and validated through ground based experimental testing. In addition, methods for ground to flight scaling are being developed and refined.

Rivers, Melissa↗

An investigation of drag reduction for a standard truck with various modifications

A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a standard truck model. The physical variables included: a cab mounted air deflector; a boattail on the rear of the cargo compartment; flow-vanes on the front of the cargo compartment; and a forebody fairing over the cab. Tests were conducted at yaw angles (relative wind angle) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.4 x 100,000 to 6.1 x 100,000 based upon the equivalent diameter of the vehicles. The forebody fairing and the flow-vane with the closed bottom were very effective in improving the flow over the forward part of the cargo compartment. The forebody fairing provided a calculated fuel saving of 5.6 liters per hour (1.5 gallons per hour) over the baseline configuration for a ground speed of 88.6 km/hr (55 mph) in national average winds.

Muirhead, V. U.↗

Flight Testing of a Low Cost De-Orbiting Device for Small Satellites

Use of small and very small spacecraft is rapidly becoming more common. Methods to intentionally deorbit these spacecraft at the end of useful satellite life are required. A family of mass efficient Roll-Out De- Orbiting devices (RODEO"TM") was developed by Composite Technology Development, Inc. (CTD). RODEO"TM" consists of lightweight film attached to a simple, ultra-lightweight, roll-out composite boom structure. This system is rolled to stow within a lightweight launch canister, allowing easy integration to the small satellite bus. The device is released at the end of useful lifetime and the RODEO"TM" composite boom unrolls the drag sail in a matter of seconds. This dramatically increases the deployed surface area, resulting in the higher aerodynamic drag that significantly reduces the time until reentry. A RODEO"TM" flight demonstration was recently conducted as part of the Colorado Space Grant Consortium's (COSGC) RocketSat-8 program, a program to provide students hands-on experience in developing experiments for space flight. The experiment was ultimately a success and RODEO (trademark) is now ready for future CubeSat missions.

Turse, Dana↗

An investigation of drag reduction for tractor trailer vehicles with air deflector and boattail

A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a trailer model. The physical variables included: a cab mounted wind deflector, boattail on trailer, flow vanes on trailer front, forced transition on trailer, and decreased gap between tractor and trailer. Tests were conducted at yaw angles (relative wind angles) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.58 x 10 to the 5th power 6.12 x 10 to the 5th power based upon the equivalent diameter of the vehicles. The wind deflector on top of the cab produced a calculated reduction in fuel consumption of about 5 percent of the aerodynamic portion of the fuel budget for a wind speed of 15.3 km/hr (9.5 mph) over a wind angle range of 0 deg to 180 deg and for a vehicle speed of 88.5 km/hr (55 mph). The boattail produced a calculated 7 percent to 8 percent reduction in fuel consumption under the same conditions. The decrease in gap reduced the calculated fuel consumption by about 5 percent of the aerodynamic portion of the fuel budget.

Muirhead, V. U.↗

Flight test evaluation of drag effects on surface coatings on the NASA Boeing 737 TCV airplane

A flight test program was conducted in which the effects of various surface coatings on aerodynamic drag were investigated; results of this program are described in this report. The tests were conducted at NASA-Langley Research Center on the terminal configured vehicle (TCV) Boeing 737 research airplane. The Boeing Company, as contractor with NASA under the Energy Efficient Transport (EET) program, planned and evaluated the experiment. The NASA-TCV Program Office coordinated the experiment and performed the flight tests. The principal objective of the test was to evaluate the drag reduction potential of an elastomeric polyurethane surface coating, CAAPCO B-274, which also has been considered for application on transport airplanes to protect leading edges from erosion. The smooth surface achievable with this type of coating held some promise of reducing the skin friction drag as compared to conventional production type aircraft surfaces, which are usually anodized bare metal or coated with corrosion protective paint. Requirements for high precision measurements were the principal considerations in the experiment.

George-Falvy, D.↗

Application of microgravity and containerless environments to the investigation of fusion target fabrication technology

After the first observation of the core-centering force within a liquid shell in the KC-135 flight experiment, this force was successfully reproduced in terrestrial laboratories using two experimental techniques. The core-centering force generated for a compound drop system in the neutral buoyancy tank provides the first correlation between theoretical and experimental results. When this force was generated in a more realistic fusion-pellet system using the focusing-radiator levitating system, it was shown that this is a very strong force indeed in view of the fact that the ratio of specific gravities between the water and the core is approximately five. It is believed that this centering force will contribute significantly to an overall understanding of the fabrication physics of a fusion target system. Results from experiments in a vertical drag-free wind tunnel and in a 16-ft low pressure drop furnace suggest that eliminating or reducing the aerodynamic drag on fusion pellets during their formation stage will prevent the decentering of the bubble. Metallic and metallic glass fusion targets are seen as holding promise for improving and simplifying the fabrication process for ablative-type fusion targets.

Lee, M. C.↗

Acoustic Liner Drag: Further Measurements on Novel Facesheet Perforate Geometries

Over the past several years, the NASA Langley Liner Physics Team has worked to develop methods capable of characterizing the aerodynamic drag of acoustic liners in addition to their acoustic performance. For a given liner, one can compute its resistance factor, λ, based on static pressure drop measurements. The current study details experiments in the NASA Langley Grazing Flow Impedance Tube to quantify the relative drag of several perforate-over-honeycomb liner configurations at flow speeds of Mach 0.3 and 0.5. The liner facesheets incorporate novel perforate geometries rather than the conventional, round hole designs typically used. Measurements of the resistance factor for each liner are made with and without acoustic excitation. A tonal acoustic source is used at sound pressure levels of 140 and 150 dB over a frequency range of 400 to 3000 Hz when performing acoustic measurements. Educed impedance spectra are calculated to determine the impact of variations in perforate geometry on acoustic performance and the relationship between acoustic and drag performance.

Howerton, Brian M.↗

Orbit keeping attitude control for space station

It is pointed out that on-orbit configuration variability is expected to be a characteristic of a space station. The implementation of such a chracteristic will present reboost and thruster control system designers with a number of new challenges. The primary requirement for the space station orbit reboost (or orbit keeping) system is to ensure system viability for extended duration and prevent an uncontrolled reentry as with Skylab. For a station in a low earth orbit, earodynamic drag will be sufficient to cause relatively quick orbit altitude decay. A propulsion system is, therefore, needed to counteract the aerodynamic drag forces and to boost the vehicle to the desired orbit altitudes. A description is given of a typical reboost operational procedure and propellant requirements. Attention is given to thruster control systems, and aspects of reboost guidance.

Barrows, D.↗

Computing interference flows past cylinder-fin-sting assembly in and near a cavity

The internal carriage of stores by the military aircraft is an option, particularly at high speeds, for a possible reduction in the aerodynamic drag and in the radar observability. Trade studies of this option, which include the safe separation of stores from their bays and aerodynamic complications of a cavity flow, require studying the aircraft and the stores together. With this motivation, the computer code, VISCC, is developed to solve the three-dimensional, Reynolds-averaged, unsteady, compressible, and complete Navier-Stokes equations. The store considered here for simulation is a missile configuration with four tail fins and an L-shaped offset sting. The missile is placed first directly above the opening of a rectangular box cavity, then submerged completely inside the cavity. The freestream Mach and the unit Reynolds numbers are 2.75 and 2.97 million per foot, respectively. The results of the time-accurate computations depict these complex flows and help understanding the interference effects. The time-averaged surface pressures compare favorably with the available wind tunnel data.

Baysal, O.↗

Performance Impact of Deflagration to Detonation Transition Enhancing Obstacles

A sub-model is developed to account for the drag and heat transfer enhancement resulting from deflagration-to-detonation (DDT) inducing obstacles commonly used in pulse detonation engines (PDE). The sub-model is incorporated as a source term in a time-accurate, quasi-onedimensional, CFD-based PDE simulation. The simulation and sub-model are then validated through comparison with a particular experiment in which limited DDT obstacle parameters were varied. The simulation is then used to examine the relative contributions from drag and heat transfer to the reduced thrust which is observed. It is found that heat transfer is far more significant than aerodynamic drag in this particular experiment.

Paxson, Daniel E.↗

The Effect of Drag Model on Heatshield Recession due to Particle Impacts for Martian Spacecraft

A spacecraft entering the Martian atmosphere during a dust storm may experience recession to the heatshield due to dust particle impacts. Aerodynamic drag is the primary force that determines the trajectory of the dust particles through the shock layer. This paper examines the effect of particle drag model on the heatshield recession. Three particle drag models are assessed including two that are intended to be applicable over a wide range of particle flow conditions. Particle trajectories are computed in conditions measured during the 2007 major global dust storm. It was found that accounting for Knudsen number and compressibility effects made a large difference in the estimated particle impact velocity. The two drag models that were valid for transitional, compressible particle flow environments predicted only slightly-different amounts of heatshield recession due to dust particle impacts. A brief description of the effects of non-spherical particles on drag coefficients is provided.

Heatshield↗

The Effect of Drag Model on Heatshield Recession due to Particle Impacts for Martian Spacecraft

A spacecraft entering the Martian atmosphere during a dust storm may experience recession to the heatshield due to dust particle impacts. Aerodynamic drag is the primary force that determines the trajectory of the dust particles through the shock layer. This paper examines the effect of particle drag model on the heatshield recession. Three particle drag models are assessed including two that are intended to be applicable over a wide range of particle flow conditions. Particle trajectories are computed in conditions measured during the 2007 major global dust storm. It was found that accounting for Knudsen number and compressibility effects made a large difference in the estimated particle impact velocity. The two drag models that were valid for transitional, compressible particle flow environments predicted only slightly-different amounts of heatshield recession due to dust particle impacts. A brief description of the effects of non-spherical particles on drag coefficients is provided.

Heatshield↗

Analysis and evaluation of an integrated laminar flow control propulsion system

Reduction of drag has been a major goal of the aircraft industry as no other single quantity influences the operating costs of transport aircraft more than aerodynamic drag. It has been estimated that even modest reduction of frictional drag could reduce fuel costs by anywhere from 2 to 5 percent. Current research on boundary layer drag reduction deals with various approaches to reduce turbulent skin friction drag as a means of improving aircraft performance. One of the techniques belonging to this category is laminar flow control in which extensive regions of laminar flow are maintained over aircraft surfaces by delaying transition to turbulence through the ingestion of boundary layer air. While problems of laminar flow control have been studied in some detail, the prospect of improving the propulsion system of an aircraft by the use of ingested boundary layer air has received very little attention. An initial study for the purpose of reducing propulsion system requirements by utilizing the kinetic energy of boundary layer air was performed in the mid-1970's at LeRC. This study which was based on ingesting the boundary layer air at a single location, did not yield any significant overall propulsion benefits; therefore, the concept was not pursued further. However, since then it has been proposed that if the boundary layer air were ingested at various locations on the aircraft surface instead of just at one site, an improvement in the propulsion system might be realized. The present report provides a review of laminar flow control by suction and focuses on the problems of reducing skin friction drag by maintaining extensive regions of laminar flow over the aircraft surfaces. In addition, it includes an evaluation of an aircraft propulsion system that is augmented by ingested boundary layer air.

Keith, Theo G., Jr.↗

GRACE Mission Design: Impact of Uncertainties in Disturbance Environment and Satellite Force Models

The Gravity Recovery and Climate Experiment (GRACE) primary mission will be performed by making measurements of the inter-satellite range change between two co-planar, low altitude, near-polar orbiting satellites. Understanding the uncertainties in the disturbance environment, particularly the aerodynamic drag and torques, is critical in several mission areas. These include an accurate estimate of the spacecraft orbital lifetime, evaluation of spacecraft attitude control requirements, and estimation of the orbital maintenance maneuver frequency necessitated by differences in the drag forces acting on both satellites. The FREEMOL simulation software has been developed and utilized to analyze and suggest design modifications to the GRACE spacecraft. Aerodynamic accommodation bounding analyses were performed and worst-case envelopes were obtained for the aerodynamic torques and the differential ballistic coefficients between the leading and trailing GRACE spacecraft. These analyses demonstrate how spacecraft aerodynamic design and analysis can benefit from a better understanding of spacecraft surface accommodation properties, and the implications for mission design constraints such as formation spacing control.

Mazanek, Daniel D.↗