Search NASA⌕ Search

SEARCH · Search NASA

Results for “airfoil design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Aerodynamic characteristics of the 10-percent-thick NASA supercritical airfoil 33 designed for a normal-force coefficient of 0.7

A 10-percent-thick supercritical airfoil based on an off-design sonic-pressure plateau criterion was developed and experimental aerodynamic characteristics measured. The airfoil had a design normal-force coefficient of 0.7 and was identified as supercritical airfoil 33. Results show the airfoil to have good drag rise characteristics over a wide range of normal-force coefficients with no measurable shock losses up to the Mach numbers at which drag divergence occurred for normal-force coefficients up to 0.7. Comparisons of experimental and theoretical characteristics were made and composite drag rise characteristics were derived for normal-force coefficients of 0.5 and 0.7 and a Reynolds number of 40 million.

Harris, C. D.↗
NASA NTRS1999

Active Control of Flow Separation Over an Airfoil

Designing an aircraft without conventional control surfaces is of interest to aerospace community. In this direction, smart actuator devices such as synthetic jets have been proposed to provide aircraft maneuverability instead of control surfaces. In this article, a numerical study is performed to investigate the effects of unsteady suction and blowing on airfoils. The unsteady suction and blowing is introduced at the leading edge of the airfoil in the form of tangential jet. Numerical solutions are obtained using Reynolds-Averaged viscous compressible Navier-Stokes equations. Unsteady suction and blowing is investigated as a means of separation control to obtain lift on airfoils. The effect of blowing coefficients on lift and drag is investigated. The numerical simulations are compared with experiments from the Tel-Aviv University (TAU). These results indicate that unsteady suction and blowing can be used as a means of separation control to generate lift on airfoils.

Ravindran, S. S.↗
NASA NTRS1987

Wind tunnel results of the high-speed NLF(1)-0213 airfoil

Wind tunnel tests were conducted to evaluate a natural laminar flow airfoil designed for the high speed jet aircraft in general aviation. The airfoil, designated as the High Speed Natural Laminar Flow (HSNLF)(1)-0213, was tested in two dimensional wind tunnels to investigate the performance of the basic airfoil shape. A three dimensional wing designed with this airfoil and a high lift flap system is also being evaluated with a full size, half span model.

Sewall, William G.↗
NASA NTRS1995

An approach to the constrained design of natural laminar flow airfoils

A design method has been developed by which an airfoil with a substantial amount of natural laminar flow can be designed, while maintaining other aerodynamic and geometric constraints. After obtaining the initial airfoil's pressure distribution at the design lift coefficient using an Euler solver coupled with an integml turbulent boundary layer method, the calculations from a laminar boundary layer solver are used by a stability analysis code to obtain estimates of the transition location (using N-Factors) for the starting airfoil. A new design method then calculates a target pressure distribution that will increase the larninar flow toward the desired amounl An airfoil design method is then iteratively used to design an airfoil that possesses that target pressure distribution. The new airfoil's boundary layer stability characteristics are determined, and this iterative process continues until an airfoil is designed that meets the laminar flow requirement and as many of the other constraints as possible.

Green, Bradford Earl↗
NASA NTRS1997

An Approach to the Constrained Design of Natural Laminar Flow Airfoils

A design method has been developed by which an airfoil with a substantial amount of natural laminar flow can be designed, while maintaining other aerodynamic and geometric constraints. After obtaining the initial airfoil's pressure distribution at the design lift coefficient using an Euler solver coupled with an integral turbulent boundary layer method, the calculations from a laminar boundary layer solver are used by a stability analysis code to obtain estimates of the transition location (using N-Factors) for the starting airfoil. A new design method then calculates a target pressure distribution that will increase the laminar flow toward the desired amount. An airfoil design method is then iteratively used to design an airfoil that possesses that target pressure distribution. The new airfoil's boundary layer stability characteristics are determined, and this iterative process continues until an airfoil is designed that meets the laminar flow requirement and as many of the other constraints as possible.

Green, Bradford E.↗
NASA NTRS1980

Rotor redesign for a highly loaded 1800 ft/sec tip speed fan, 2

Tests were conducted on a 0.5 hub/tip ratio single-stage fan designed to produce a pressure ratio of 2.280 at an efficiency of 83.8 percent with a rotor tip speed of 548.6 m/sec (1800 ft/sec). The rotor was designed utilizing a quasi three dimensional design system and four-part, multiple-circular-arc airfoil sections. The rotor is the third in a series of single-stage fans that have included a precompression airfoil design and a multiple-circular-arc airfoil design. The stage achieved a peak efficiency of 82.8 percent after performance had deteriorated by 0.6 of a point. The design mass flow was achieved at the peak efficiency point, and the stage total pressure ratio was 2.20, which is lower than the design goal of 2.28. The surge margin of 13% from the peak efficiency point exceeded the design goal of 7%.

Bolt, C. R.↗
NASA NTRS1975

Transonic airfoil analysis and design using Cartesian coordinates

An inverse numerical technique for designing transonic airfoils having a prescribed pressure distribution is presented. The method uses the full potential equation, inverse boundary conditions, and Cartesian coordinates. It includes simultaneous airfoil update and utilizes a direct-inverse approach that permits a logical method for controlling trailing edge closure. The method can also be used for the analysis of flowfields about specified airfoils. Comparison with previous results shows that accurate results can be obtained with a Cartesian grid. Examples show the application of the method to design aft-cambered and other airfoils specifically for transonic flight.

Carlson, L. A.↗
NASA NTRS1952

On the design of airfoils in which the transition of the boundary layer is delayed

A method is presented for designing suitable thickness distributions and mean camber lines for airfoils permitting extensive chordwise laminar flow. Wind tunnel and flight tests confirming the existence of laminar flow; possible maintenance of laminar flow by area suction; and the effects of wind tunnel turbulence and surface roughness on the promotion of premature boundary layer transition are discussed. In addition, estimates of profile drag and scale effect on maximum lift of the derived airfoils are made.

BOUNDARY LAYER CONTROL - AIRFOILS↗
NASA NTRS1978

Design and analytical study of a rotor airfoil

An airfoil section for use on helicopter rotor blades was defined and analyzed by means of potential flow/boundary layer interaction and viscous transonic flow methods to meet as closely as possible a set of advanced airfoil design objectives. The design efforts showed that the first priority objectives, including selected low speed pitching moment, maximum lift and drag divergence requirements can be met, though marginally. The maximum lift requirement at M = 0.5 and most of the profile drag objectives cannot be met without some compromise of at least one of the higher order priorities.

Dadone, L. U.↗
NASA NTRS1987

Design and test of a natural laminar flow/large Reynolds number airfoil with a high design cruise lift coefficient

Research activity on an airfoil designed for a large airplane capable of very long endurance times at a low Mach number of 0.22 is examined. Airplane mission objectives and design optimization resulted in requirements for a very high design lift coefficient and a large amount of laminar flow at high Reynolds number to increase the lift/drag ratio and reduce the loiter lift coefficient. Natural laminar flow was selected instead of distributed mechanical suction for the measurement technique. A design lift coefficient of 1.5 was identified as the highest which could be achieved with a large extent of laminar flow. A single element airfoil was designed using an inverse boundary layer solution and inverse airfoil design computer codes to create an airfoil section that would achieve performance goals. The design process and results, including airfoil shape, pressure distributions, and aerodynamic characteristics are presented. A two dimensional wind tunnel model was constructed and tested in a NASA Low Turbulence Pressure Tunnel which enabled testing at full scale design Reynolds number. A comparison is made between theoretical and measured results to establish accuracy and quality of the airfoil design technique.

Kolesar, C. E.↗
NASA NTRS1982

Experimental studies of the Eppler 61 airfoil at low Reynolds numbers

The results of an experimental study to document the effects of separation and transition on the performance of an airfoil designed for low Reynolds number operation are presented. Lift, drag and flow visualization data were obtained for the Eppler 61 airfoil section for chord Reynolds numbers from about 30,000 to over 200,000. Smoke flow visualization was employed to document the boundary layer behavior and was correlated with the Eppler airfoil design and analysis computer program. Laminar separation, transition and turbulent reattachment had significant effects on the performance of this airfoil.

Burns, T. F.↗
NASA NTRS1982

Boeing Vertol noise reduction experience

Boeing Vertol Model 234, CH-47D and 347 tandem rotor helicopters demonstrate noise levels that comply with the overall noise standard requirements. The helicopters achieve these noise levels because they are, by design, free of impulsive noise in level flight and climb. Avoiding an impulsive noise signature is achieved by developing and applying configuration design criteria that eliminate blade vortex intersections and recognize advancing blade tip noise limitations in high speed forward flight. Airfoil design, rotor separation and rotor tipspeed selection all contribute to the noise control. Compliance with the approach element of the standards is marginal at best. The approach problem is not appreciably alleviated by reduced tipspeed and airfoil design. Since it is a single rotor phenomenon, it is not alleviated by rotor separation in the tandem configuration. Tip shapes may provide the answer, but to date this approach has not led to a satisfactory solution.

Walls, W. W.↗
NASA NTRS1984

An Experimental Evaluation of Advanced Rotorcraft Airfoils in the NASA Ames Eleven-foot Transonic Wind Tunnel

Five full scale rotorcraft airfoils were tested in the NASA Ames Eleven-Foot Transonic Wind Tunnel for full scale Reynolds numbers at Mach numbers from 0.3 to 1.07. The models, which spanned the tunnel from floor to ceiling, included two modern baseline airfoils, the SC1095 and SC1094 R8, which have been previously tested in other facilities. Three advanced transonic airfoils, designated the SSC-A09, SSC-A07, and SSC-B08, were tested to confirm predicted performance and provide confirmation of advanced airfoil design methods. The test showed that the eleven-foot tunnel is suited to two-dimensional airfoil testing. Maximum lift coefficients, drag coefficients, pitching moments, and pressure coefficient distributions are presented. The airfoil analysis codes agreed well with the data, with the Grumman GRUMFOIL code giving the best overall performance correlation.

Flemming, Robert J.↗
NASA NTRS2020

Robust Conceptual Design of Transonic Airfoils

This paper describes an integrated, multi-fidelity analysis and heuristic design approach that can be used to derive initial airfoil designs for transonic flight. If successful, the final result is a geometry that can be expected to produce reasonable aerodynamic performance when used with higher order analysis methods. A key aspect of the methodology is the use of a “sonic-plateau” pressure distribution as the target distribution for inverse design. The sonic- plateau distribution is easily parameterized and has the advantage of automatically resulting in a smooth airfoil shape without any discontinuities built into the surface due to the presence of a shock in the target pressure distribution. Inverse design is performed on each airfoil using a parametrically defined pressure distribution at a reduced lift coefficient and Mach number from the design condition. The methodology is demonstrated by designing an airfoil at 38% of the wing semispan for a 737-200-like aircraft. The demonstration problem shows that the methodology is able to achieve rapid and robust convergence to the solution. The calculated designed airfoil was found to be sufficiently higher than Mach number, and the maximum thickness was close to the targeted value.

Olson, Erik D.↗
NASA NTRS1993

Demonstration of multipoint design procedures for transonic airfoils

Two multipoint design procedures were applied to reduce the wave drag of a baseline airfoil at two design points. The first procedure iteratively averages two intermediate airfoil shapes, each one redesigned at one of the two design points, to develop an improved airfoil. The second procedure iteratively averages two pressure distributions, each one obtained from an intermediate airfoil redesigned at one of the two design points, to develop an improved airfoil. Successful application of each procedure to design an improved airfoil for design points with similar chordwise pressure distributions, shock locations, and shock strengths is demonstrated. Application of a combination of both procedures to design an improved airfoil at design points with dissimilar chordwise pressure distributions, shock locations, and shock strengths is also presented. Results from wind tunnel tests of the baseline airfoil and of the improved airfoil for the dissimilar design points verified the predicted drag improvements.

Mineck, Raymond E.↗
NASA NTRS1961

Hovering Characteristics of a Rotor having an Airfoil Section Designed for Flying-Crane Type of Helicopter

Results of an investigation, conducted on the Langley helicopter test tower, of a rotor having an NACA 632A015 airfoil thickness distribution in combination with an NACA 230 mean line are presented. Comparison with a previously reported test of a symmetrical rotor blade efficiency was substantially improved over a wide range of tip Mach numbers. The maximum mean lift coefficient was essentially unchanged from that obtained with uncambered blades. Some data showing the effect of a distributed type of leading-edge roughness are also included.

Shivers, James P.↗