SEARCH · Search NASA

Results for “anode catalyst”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Electrosynthesis of ethylene glycol from C 1 feedstocks in a flow electrolyzer

Ethylene glycol is a widely utilized commodity chemical, the production of which accounts for over 46 million tons of CO 2 emission annually. Here we report a paired electrocatalytic approach for ethylene glycol production from methanol. Carbon catalysts are effective in reducing formaldehyde into ethylene glycol with a 92% Faradaic efficiency, whereas Pt catalysts at the anode enable formaldehyde production through methanol partial oxidation with a 75% Faradaic efficiency. With a membrane-electrode assembly configuration, we show the feasibility of ethylene glycol electrosynthesis from methanol in a single electrolyzer. The electrolyzer operates a full cell voltage of 3.2 V at a current density of 100 mA cm -2 , with a 60% reduction in energy consumption. Further investigations, using operando flow electrolyzer mass spectroscopy, isotopic labeling, and density functional theory (DFT) calculations, indicate that the desorption of a *CH 2 OH intermediate is the crucial step in determining the selectively towards ethylene glycol over methanol.

09 BIOMASS FUELS↗

DOE OSTI2021

Achieving 5,000-h and 8,000-h Low-PGM Electrode Durability on Automotive Drive Cycles

Whereas total Pt loading in anode and cathode catalysts below 0.125 mg cm −2 is required to meet the stringent cost target for automotive fuel cell systems (FCS) for light duty vehicles, low-loaded cathode catalysts are susceptible to unacceptable aging-related performance losses at high current densities. A framework model, validated by accelerated stress test data, has identified cell voltage, relative humidity (RH) and temperature as the key operating variables that affect degradation of a high-activity d-PtCo/C cathode catalyst with 0.1 mg cm −2 Pt loading. Drive cycle simulations indicate that these can be controlled by properly selecting the minimum FCS power, compressor-expander module (CEM) turndown, and stack coolant temperature. The optimum system parameters are 4-kW e minimum power for an 80-kW e FCS, CEM turndown of 12.5, and 66 °C average coolant exit temperature that combine to limit the maximum cell voltage to 850 mV and outlet RH to 90%–100%. Depending on Pt loading, the mismatch between actual and allowable degradation for 10% power loss over 5,000-h lifetime requires the stack to be oversized by 2.4%–5%, resulting in 8.4%–41% lower Pt utilization and 7.1%–20.5% penalty in stack cost. The corresponding results for 8,000-h lifetime are 10.3%-14% stack oversizing, 23%–51.8% lower Pt utilization, and 24.1%–35.4% stack cost penalty.

08 HYDROGEN↗

DOE OSTI2021

Tuning Surface Stoichiometry of SOFC Electrodes at the Molecular and Nano-scale for Enhanced Performance and Durability

This project achieved the following objectives. Different cation segregation behaviors of different common SOFC cathodes, including La 0.6 Sr 0.4 Co0.2Fe 0.8 O 3-δ (LSCF), Sr 0.5 Sm 0.5 O 3-δ (SSC), and PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O5 +δ (PBSCF), were determined. We showed how oxygen partial pressure and gas impurities impact the stability of SOFC cathodes. We developed atomic layer deposition (ALD) coating techniques for electrodes and showed that by introducing different elements and different ALD oxidizers, electrode surface chemistry can be altered, resulting in enhanced oxygen reduction kinetics. In addition, we developed solution infiltration technique to enhance performance and durability of electrodes. Different infiltrates as well as different thermal treatment processes were screened to identify the optimal surface modification process that yields both low impedance and high durability. The modified cathode shows excellent stability and has a low area specific resistance (ASR) of only 0.2 Ωcm 2 at 600 °C after over 2000 hours of operation. Further, we developed ceramic anodes, SrFe(Co,Mo)O 3 (SFCM) and SrFe(Ni,Mo)O 3 (SFNM), and enhanced anode oxidation kinetics by solution infiltration or in situ catalyst exsolution from the ceramic anode surface. The modified anodes showed improved performance in full SOFCs, and the optimized anode modification shows high stability for over 400 hours at 550 °C. Moreover, the modified anode also demonstrates high durability in methane. This work provides fundamental understanding of electrode surface chemistry and demonstrates a simple, facile, cost-effective approach to enhance catalytic activity and durability of SOFC electrodes.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2020

Reactor with advanced architecture for the electrochemical reaction of CO2, CO, and other chemical compounds

A platform technology that uses a novel membrane electrode assembly including a cathode layer comprising a reduction catalyst and a first anion-and-cation-conducting polymer, an anode layer comprising an oxidation catalyst and a cation-conducting polymer, a membrane layer comprising a cation-conducting polymer, the membrane layer arranged between the cathode layer and the anode layer and conductively connecting the cathode layer and the anode layer, in a COx reduction reactor has been developed. The reactor can be used to synthesize a broad range of carbon-based compounds from carbon dioxide.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Reactor with advanced architecture for the electrochemical reaction of CO2, CO, and other chemical compounds

Kuhl, Kendra P.↗

DOE OSTI2020

Hierarchically-Structured Ti/TiO 2 Electrode for Hydrogen Evolution Synthesized via 3D Printing and Anodization

Hierarchically-structured, electro-catalysts consisting of a titanium core with controlled macro-porosity and a thin titania surface-layer with controlled nano-porosity were synthesized via combination of additive manufacturing and in-situ anodization. The electrodes were tested for hydrogen evolution reaction and depicted competitive electro-catalytic activities, with Tafel slopes between 40 and 56 mV dec -1 . The electrodes also depicted competitive onset and over potentials when compared with other electrode alternatives. The synthesis approach for the electro-catalysts reported in this work is being extended to other metal/metal-oxide pairs and applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Durable, pure water–fed, anion-exchange membrane electrolyzers through interphase engineering

Anion-exchange membrane water electrolyzers (AEMWEs) promise scalable, low-cost hydrogen production but are limited by the electrochemical instability of their anode ionomers. We report interphase engineering using inorganic-containing molecular additives that coassemble with ionomer, enabling pure water-fed AEMWEs to operate with a degradation rate <0.5 millivolt per hour at 2.0 amperes per square centimeter and 70°C-a >20-fold durability improvement. Analysis of different additives and ionomers shows that the stabilization mechanism involves cross-links between metal oxo/hydroxo oligomers and ionomers. Under operation, the inorganic additive enriches, forming an interphase near the water-oxidation catalyst that passivates the anode ionomer against continuous degradation while maintaining mechanical integrity and hydroxide conductivity. This additive-based interphase-engineering strategy provides a path to durable AEMWEs that operate without supporting electrolytes and is adaptable across diverse catalysts and ionomers for electrochemical technologies.

Hou, Shujin↗

DOE OSTI2022

Novel Co‐Catalytic Activities of Solid and Liquid Phase Catalysts in High‐Rate Li‐Air Batteries

Abstract Li‐air batteries are considered strong candidates for the next‐generation energy storage systems designed for electrical transportation. However, low cyclability and current rates are two major drawbacks that hinder them from further realization. These issues necessitate the discovery of novel materials to significantly enhance the redox process of discharge products. In this study, a novel catalytic system comprised of tin sulfide (SnS) nanoflakes as a solid catalyst and tin iodide (SnI 2 ) as a dual‐functional electrolyte additive is discovered. This system enables operating the battery at high current rates up to 10 000 mA g −1 (corresponding to 1 mA cm −2 ). The SnS catalyst shows outstanding catalytic activity for both oxygen reduction and evolution reactions compared to carbon, noble metals, and other transition metal dichalcogenides. It also exhibits good structural integrity at high rates. The computations indicate numerous possible oxygen reduction sites without oxygen dissociations on the SnS surface through solution mechanism that is likely responsible for the formation of Li 2 O 2 . The calculations also indicate that the role of the SnI 2 is not only reacting with the lithium anode to provide protection but reducing the charge potential by promoting catalytic decomposition of the Li 2 O 2 . This work provides new novel additives for designing high‐rate Li‐air batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

Boosting the performances of protonic solid oxide fuel cells for co-production of propylene and electricity from propane by integrating thermo- and electro- catalysis

Protonic solid oxide fuel cells (p-SOFC) integrated with clean thermal energy sources are promising platforms for decarbonized chemical production in addition to power generation, such as on-purpose propylene production from propane dehydrogenation (PDH). The catalytic performance of the conventional nickel-cermet-based anode materials in p-SOFC for propane conversion is restrained by their low active surface area and proneness to coking. In this work, by integration of a highly efficient industry-relevant thermal catalyst PtGa/ZSM-5 for PDH reaction, we demonstrate that both the electrochemical and catalytic performance of the propane-fueled p-SOFC can be effectively enhanced. The PtGa catalyst integrated p-SOFC exhibits a peak power density of 93 mW cm -2 at 600°C, which is greater by about 100% and 50% than that without catalyst or with a perovskite-based (Pr 0.3 Sr 0.7 ) 0.9 Ni 0.1 Ti 0.9 O 3 (PSNT) catalyst layer, respectively. The PDH activity and olefin selectivity of the PtGa catalyst is also significantly higher than that of the PSNT catalyst. In addition, much improved coke tolerance and propylene selectivity (over 90%) compared to the catalyst-free Ni-cermet anode materials were achieved by integrating the industrial catalyst layer. The propane conversion can be further improved by an applied current density, whereas the olefin selectivity is almost unaltered. The excellent performance of the PtGa catalyst integrated p-SOFC is attributed to the high surface area, intrinsically high catalytic activity, selectivity, and anti-coking properties of the catalytic layer for propane conversion. In conclusion, this work provides a general approach and a case study for boosting the performances of p-SOFCs in chemical production by integrating thermo- and electro- catalysis.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Understanding and improving anode performance in an alkaline membrane electrolyzer using statistical design of experiments

The behavior of the oxygen-evolving positive electrode (i.e. anode) in the anion exchange membrane water electrolyzer (AEMEL) is complex and influenced by several factors. Very few studies have been performed to understand oxygen evolution reaction (OER) behavior by optimizing the individual factors that influence performance. Here, this study highlights the effects of catalyst loading, catalyst selection, porous transport layer (PTL) type and conductive additive content. The influence of each factor is elucidated through a design of experiments (DoE) approach with a full statistical analysis. Electrochemical data, alongside Pareto charts, parametric trends and their mutual interactions are discussed. This DoE approach is also helpful in making useful predictions and discovering new combinations to be tested. The end result was a high-performance AEMEL able to operate at a current density of 1.0 A/cm 2 at 1.80 V with IrOx OER and PtNi hydrogen evolution reaction (HER) catalysts using 0.3 M KOH fed to the anode. Even lower operating voltage was observed with PbRuOx catalyst at the anode, 1.64 V @ 1.0 A/cm 2 , though the cell decay rate was higher. Lastly, a IrOx/PtNi cell was stably operated continuously for 30 days (720 h) at 1.0 A/cm 2 . This study can serve as a guide for optimal electrode design with insights into component-performance compromises, which can aid in making design choices and performing techno-economic analyses.

08 HYDROGEN↗

DOE OSTI2025

In situ studies of a molten metal anode ablation in a nearly atmospheric pressure DC arc

A DC arc with a meltable metal anode in a near-atmospheric pressure hydrocarbon gas is an emerging method for producing single-walled carbon nanotubes (SWCNTs). In these systems, evaporation of the molten metal anode determines the formation of catalyst seed particles needed for SWCNT growth, and therefore, should be monitored, controlled, and optimized. Evaluating the anode ablation rate by weighing the anode before and after a synthesis run is unfeasible due to anode carburization in the hydrocarbon atmosphere. To overcome this, we implemented a high-speed, 2D, 2-color pyrometry for reliable temperature measurements of the molten anode in a DC arc. The obtained temperature fields were used to calculate the anode ablation rates. Results showed the importance of resolving the arc and molten pool dynamics, as well as addressing the issue of reflections. Furthermore, significant changes in ablation rates were revealed upon addition of CH 4 , which must be considered when scaling up the production of SWCNTs.

Marangoni↗

DOE OSTI2026

Mitigating Hydrogen-Induced Degradation of Iridium Anodes in Proton Exchange Membrane Water Electrolyzers

One promising method for reducing precious metal usage in proton exchange membrane water electrolysis is lowering iridium (Ir) loading at the anode. However, low-loading Ir catalysts often suffer from poor stability under high current densities. In this study, hydrogen (H2) crossover from the cathode to the anode is identified as a key degradation pathway. Temperature-programmed reduction confirms the reduction of IrO2 at 80 °C in a hydrogen environment, highlighting the vulnerability of IrO2-based catalysts to H2 exposure. To mitigate this effect, palladium (Pd) is introduced as an anode additive, acting as an H2 oxidation catalyst and mitigating IrO2 reduction. This protective role is verified by inductively coupled plasma optical emission spectroscopy and in situ X-ray absorption spectroscopy, showing significantly suppressed Ir dissolution at 80 °C under H2 flow when an O-covered Pd surface is present at oxygen evolution reaction potentials. Results from the current study identify a new strategy in improving activity and durability of catalysts in electrolyzers.

58 GEOSCIENCES↗

DOE OSTI2022

Discovery of LaAlO 3 as an efficient catalyst for two-electron water electrolysis towards hydrogen peroxide

Electrochemical two-electron water oxidation reaction (2e-WOR) has drawn significant attention as a promising process to achieve the continuous on-site production of hydrogen peroxide (H 2 O 2 ). However, compared to the cathodic H 2 O 2 generation, the anodic 2e-WOR is more challenging to establish catalysts due to the severe oxidizing environment. In this study, we combine density functional theory (DFT) calculations with experiments to discover a stable and efficient perovskite catalyst for the anodic 2e-WOR. Our theoretical screening efforts identify LaAlO 3 perovskite as a stable, active, and selective candidate for catalyzing 2e-WOR. Our experimental results verify that LaAlO 3 achieves an overpotential of 510 mV at 10 mA cm -2 in 4 M K 2 CO 3 /KHCO 3 , lower than those of many reported metal oxide catalysts. In addition, LaAlO 3 maintains a stable H 2 O 2 Faradaic efficiency with only a 3% decrease after 3 h at 2.7 V vs. RHE. This computation-experiment synergistic approach introduces another effective direction to discover promising catalysts for the harsh anodic 2e-WOR towards H 2 O 2 .

08 HYDROGEN↗

DOE OSTI2023

On the Operando Structure of Ruthenium Oxides during the Oxygen Evolution Reaction in Acidic Media

In the search for rational design strategies for oxygen evolution reaction (OER) catalysts, linking the catalyst structure to activity and stability is key. However, highly active catalysts such as IrO x and RuO x undergo structural changes under OER conditions, and hence, structure–activity–stability relationships need to take into account the operando structure of the catalyst. Under the highly anodic conditions of the oxygen evolution reaction (OER), electrocatalysts are often converted into an active form. Here, we studied this activation for amorphous and crystalline ruthenium oxide using X-ray absorption spectroscopy (XAS) and electrochemical scanning electron microscopy (EC-SEM). We tracked the evolution of surface oxygen species in ruthenium oxides while in parallel mapping the oxidation state of the Ru atoms to draw a complete picture of the oxidation events that lead to the OER active structure. Our data show that a large fraction of the OH groups in the oxide are deprotonated under OER conditions, leading to a highly oxidized active material. The oxidation is centered not only on the Ru atoms but also on the oxygen lattice. This oxygen lattice activation is particularly strong for amorphous RuO x . We propose that this property is key for the high activity and low stability observed for amorphous ruthenium oxide.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Flow-based anode for the electrocatalytic oxidation of a fuel or other reductant

Anode half-cells for the electrocatalytic oxidation of a liquid or gaseous fuel or other reductant are disclosed, along with electrochemical cells that include such half-cells. The anode half-cells include redox mediator/heterogeneous redox catalyst pairs within an electrolyte solution that is also in contact with an electrode. The electrode is not in direct contact with the heterogeneous catalyst. The redox mediator must include at least one carbon atom and be capable of transferring or accepting electrons and protons while undergoing reduction or oxidation.In operation, the fuel or other reductant is oxidized and the redox mediator is reduced at the heterogeneous catalyst. The reduced form of the redox mediator can then migrate to the electrode, where it is converted back to its oxidized form, which can then migrate back to the heterogeneous catalyst, where the cycle is repeated. The disclosed anode half-cells can be used in electrochemical cells, such as in fuel cells that produce electricity, or in electrosynthetic cells that produce one or more desired chemical products.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Non-noble metal based electro-catalyst compositions for proton exchange membrane based water electrolysis and methods of making

The invention provides electro-catalyst compositions for an anode electrode of an acid mediated proton exchange membrane-based water electrolysis system. The compositions include a noble metal component selected from the group consisting of iridium oxide, ruthenium oxide, rhenium oxide and mixtures thereof, and a non-noble metal component selected from the group consisting of tantalum oxide, tin oxide, niobium oxide, titanium oxide, tungsten oxide, molybdenum oxide, yttrium oxide, scandium oxide, cooper oxide, zirconium oxide, nickel oxide and mixtures thereof. Further, the non-noble metal component can include a dopant. The dopant can be at least one element selected from Groups III, V, VI and VII of the Periodic Table. The compositions can be prepared using any solution based methods involving a surfactant approach or a sol gel approach. Further, the compositions are prepared using noble metal and non-noble metal precursors. Furthermore, a thin film containing the compositions can be deposited onto a substrate to form the anode electrode.

Kumta, Prashant N.↗

DOE OSTI2022

Tuning Catalyst Activation and Utilization Via Controlled Electrode Patterning for Low-Loading and High-Efficiency Water Electrolyzers

An anode electrode concept of thin catalyst-coated liquid/gas diffusion layers (CCLGDLs), by integrating Ir catalysts with Ti thin tunable LGDLs with facile electroplating in proton exchange membrane electrolyzer cells (PEMECs), is proposed. The CCLGDL design with only 0.08 mg Ir cm -2 can achieve comparative cell performances to the conventional commercial electrode design, saving ~97% Ir catalyst and augmenting a catalyst utilization to ~24 times. CCLGDLs with regulated patterns enable insight into how pattern morphology impacts reaction kinetics and catalyst utilization in PEMECs. A specially designed two-sided transparent reaction-visible cell assists the in situ visualization of the PEM/electrode reaction interface for the first time. Oxygen gas is observed accumulating at the reaction interface, limiting the active area and increasing the cell impedances. In this work, it is demonstrated that mass transport in PEMECs can be modified by tuning CCLGDL patterns, thus improving the catalyst activation and utilization. The CCLGDL concept promises a future electrode design strategy with a simplified fabrication process and enhanced catalyst utilization. Furthermore, the CCLGDL concept also shows great potential in being a powerful tool for in situ reaction interface research in PEMECs and other energy conversion devices with solid polymer electrolytes.

08 HYDROGEN↗

DOE OSTI2025

Standardization and best practices in single-cell testing for liquid alkaline water electrolysis

The increasing demand for efficient and sustainable hydrogen production has driven significant advancements in water electrolysis technologies. Among these, liquid alkaline water electrolysis (LAWE) stands out for its cost-effectiveness and scalability. This manuscript establishes best practices and standardized testing procedures for single-cell LAWE, focusing on the use of nickel foam as both anode and cathode substrates, while incorporating catalysts such as nickel-iron layered double hydroxide (NiFe-LDH) as the anode material and nickel-molybdenum on carbon (NiMo/C) as the cathode material. By providing detailed guidelines on material preparation, cell assembly, and performance evaluation, this work offers a comprehensive framework to improve reproducibility and ensure consistency. The results demonstrate that applying these best practices minimizes variability across different laboratories and experimental setups, laying the groundwork for more robust comparisons and accelerating progress in LAWE research.

08 HYDROGEN↗