Results for “anode-free manufacturing” — Page 6

NASA NTRS1985

Suppression of Marangoni Convection in Float Zones

The basic purpose of this program is to demonstrate by means of an Earth-based 1-g experiment that the undesirable Marangoni (surface tension) convection can be suppressed or significantly reduced by means of gas jets directed tangentially to the free surface of the liquid in a float zone. These jets will establish the tangential shear stress field over the surface which must be adjusted to equal the counter-stress resultant of the Marangoni shear stress which causes the convection. For proposed materials processing in space (o-g), particularly of important, highly reactive semiconductor materials, e.g., silicon, microgravity will virtually eliminate the unwanted thermal-buoyancy convection in the liquid silicon, but will have no effect in reducing the Marangoni convection. Unless this can be sufficiently suppressed by other means, there may be no significant advantages to the proposed space processing of reactive semiconductors. Although some inert gas such as argon must be used for the corrosive liquid silicon, the Earth-based experiment uses air jets and various transparent oils, since the basic principle involved is the same. The first float zone is enclosed in a very small rectangular box with a quasi-planar free surface. Stable Marangoni convection has been achieved and velocities measured photographically. The air jet system with variable velocity and temperature is under construction. Three independent parameters must be optimized to attain maximum suppression: the gas velocity, angle of attack, and gas temperature.

Robert F Dressler↗

NASA NTRS2007

Hubble Space Telescope Battery Capacity Update

Orbital battery performance for the Hubble Space Telescope is discussed and battery life is predicted which supports decision to replace orbital batteries by 2009-2010 timeframe. Ground characterization testing of cells from the replacement battery build is discussed, with comparison of data from battery capacity characterization with cell studies of Cycle Life and 60% Stress Test at the Naval Weapons Surface Center (NWSC)-Crane, and cell Cycle Life testing at the Marshal Space Flight Center (MSFC). The contents of this presentation includes an update to the performance of the on-orbit batteries, as well as a discussion of the HST Service Mission 4 (SM4) batteries manufactured in 1996 and activated in 2000, and a second set of SM4 backup replacement batteries which began manufacture Jan 11, 2007, with delivery scheduled for July 2008.

Hollandsworth, Roger↗

NASA NTRS1991

Lightweight, High-Energy Lead/Acid Battery

Concept for lead/acid battery calls for woven-grid bipolar electrodes. Stack of bipolar cells form lead/acid battery. Each cell contains pair of folded electrodes, negative on one side of fold, positive on other. In high-voltage configuration, battery has higher specific energy and power. Rugged, longlived, and maintenance-free. Made from readily available, low-cost materials by standard lead/acid production methods, well suited for use in electronic equipment, aircraft, and electric vehicles for industrial and passenger service.

Rippel, Wally E.↗

NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗

NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗

NASA NTRSDate not supplied

Effects of Ground Boards on Acoustic Signals

Acoustic ground boards are used to provide hard reflective surfaces for microphones when taking outdoor measurements. These boards also have a wide variety of potential impacts on the signal received by the microphones. A comprehensive experimental campaign was completed in which various ground board and microphone configurations were tested to determine their effects on the acoustic signals returned by the microphones. Comparisons are made between these setups and a free-field reference case. Normal impedance testing on various combinations of sand, plywood, and ground board material was also completed.

Mark CAnderson↗

NASA NTRS1991

Bipolar lead acid battery development

A modular bipolar battery configuration is under development at Johnson Control, Inc. (JCI) and the Jet Propulsion Laboratory (JPL). The battery design, incorporating proven lead acid electrochemistry, yields a rechargeable, high-power source that is light weight and compact. This configuration offers advantages in power capability, weight, and volume over conventional monopolar batteries and other battery chemistries. The lead acid bipolar battery operates in a sealed, maintenance-free mode allowing for maximum application flexibility. It is ideal for high-voltage and high-power applications.

Eskra, Michael↗

NASA NTRS1994

Review of European Microgravity Measurements

AA In a French/Russion cooperation, CNES developed a microgravity detection system for analyzing the Mir space station micro-g-environment for the first time. European efforts to characterize the microgravity (1/9) environment within a space laboratory began in the late seventies with the design of the First Spacelab Mission SL-1. Its Material Science Double Rack was the first payload element to carry its own tri-axial acceleration package. Even though incapable for any frequency analysis, the data provided a wealth of novel information for optimal experiment and hardware design and operations for missions to come. Theoretical investigations under ESA contract demonstrated the significance of the detailed knowledge of micro-g data for a thorough experiment analysis. They especially revealed the high sensitivity of numerous phenomena to low frequency acceleration. Accordingly, the payloads of the Spacelab missions D-1 and D-2 were furnished with state-of-the-art detection systems to ensure frequency analysis between 0.1 and 100 Hz. The Microgravity Measurement Assembly (MMA) of D-2 was a centralized system comprising fixed installed as well as mobile tri-axial packages showing real-time data processing and transmission to ground. ESA's free flyer EURECA carried a system for continuous measurement over the entire mission. All EURECA subsystems and experimental facilities had to meet tough requirements defining the upper acceleration limits. In a French/Russion cooperation, CNES developed a mi crogravity detection system for analyzing the Mir space station micro-g-environment for the first time. An approach to get access to low frequency acceleration between 0 and 0.02 Hz will be realized by QSAM (Quasi-steady Acceleration Measurement) on IML-2, complementary to the NASA system Spacelab Acceleration Measurement System SAMS. A second flight of QSAM is planned for the Russian free flyer FOTON.

H Hamacher↗

NASA NTRSDate not supplied

Leveraging High-Level Synthesis to Migrate Motor Control Algorithms From Microcontroller to FPGA

As motor control algorithms become increasingly complex, traditional microcontroller-based implementations are reaching computational limits that prevent the controller from operating at the required speed. This paper presents a novel workflow leveraging High-Level Synthesis (HLS) to migrate motor control algorithms from a microcontroller implementation to a Field-Programmable Gate Array (FPGA) implementation. The proposed approach utilizes the free Vitis HLS software to automatically convert Embedded Coder-generated C code from a Simulink model into Hardware Description Language (HDL) code suitable for FPGA deployment.

FPGA↗

NASA NTRSDate not supplied

Leveraging High-Level Synthesis to Migrate Motor Control Algorithms From Microcontroller to FPGA

As motor control algorithms become increasingly complex, traditional microcontroller-based implementations are reaching computational limits that prevent the controller from operating at the required speed. This paper presents a novel workflow leveraging High-Level Synthesis (HLS) to migrate motor control algorithms from a microcontroller implementation to a Field-Programmable Gate Array (FPGA) implementation. The proposed approach utilizes the free Vitis HLS software to automatically convert Embedded Coder-generated C code from a Simulink model into Hardware Description Language (HDL) code suitable for FPGA deployment.

FPGA↗

NASA NTRS1975

The 1975 GSFC Battery Workshop

The proceedings of the 1975 Goddard Space Flight Center Battery Workshop are presented. The major topics of discussion were nickel cadmium batteries and, to a lesser extent, nickel hydrogen batteries. Battery design, manufacturing techniques, testing programs, and electrochemical characteristics were considered. The utilization of these batteries for spacecraft power supplies was given particular attention.

Source record↗

NASA NTRS2026

Thermal Protection Facility: Taking the Heat

Video highlighting the products and manufacturing capabilities of the Thermal Protection Facility at Kennedy Space Center which is part of the JSC EA/ES division. This record includes an mp4 video with a run time of 9 min. 13 sec.; in color; with sound.

TPSF↗

NASA NTRS1994

Thermal Testing of High Performance: Thermal Barrier Coatings for Turbine Blades

A 350 micron thick 7 wt.% Y 2 O 3 -ZrO 2 (7YSZ) ceramic Thermal Barrier Coating (TBC) was manufactured in an argon atmosphere and with a strictly controlled substrate temperature on flat IN 600 samples and on IN 100 aircraft turbine blades. This new atmosphere and temperature controlled spraying (ATCS) allows the reduction of the residual stresses and an improvement in the microstructure and in the mechanical properties of the coating. The good performance of these new TBC's was assessed in thermal fatigue and in thermal shock tests carried out in air at 1100°C and at 1280°C respectively. The oxidation rate of the metal-ceramic interface was measured at 1100°C. Failure of the TBC's was induced only by the deterioration (like oxidation, cracking, ...) of the uncoated parts of the samples, as testing temperature was too severe for the base metals. Spalling was thereafter driven by compressive stresses near the aluminum oxide layer at the metal-ceramic interface. The results of these tests underline the good quality of the ceramic coating manufactured by the new ATCS technology.

L Bertamini↗

NASA NTRS2026

List of Commercial and Advanced Developmental Niobium-Based Alloys of the Space Age

This report compiles a list of commercial and developmental niobium-based alloys developed during the Space Age (late 1950s through mid-1970s) for extreme-temperature applications, including rocket engine thrust chambers, hypersonic re-entry thermal protection systems, and space fission reactor loops. Niobium (Nb) was widely pursued because it provided the lowest density (~8.6 g/cc) among the primary refractory metals, a high melting temperature (~2470°C), exceptional low-temperature ductility, good formability, and compatibility with liquid alkali metals. An evaluation of physical metallurgy mechanisms, focusing on solid-solution strengthening via heavy refractory solutes (W, Mo, Ta), dual-purpose reactive solutes (Hf, Zr, Ti), and dispersion strengthening using carbides, nitrides, and oxides is presented. Additionally, the report compares Western and Soviet Union metallurgical approaches, explaining how supply chain factors and manufacturing infrastructure influenced element selection, interstitial chemistry, and alloy identification/naming conventions. Cataloging these historical alloy chemical compositions serves as a foundational reference for modern alloy additive manufacturing, thermodynamic CALPHAD modeling, and machine-learning discovery pipelines for next-generation extreme-environment niobium-based alloys.

Physical Metallurgy↗

NASA NTRS1982

Pressure Switch Is a Low Cost Battery Indicator

Conventional pressure switch, fabricated by printed-circuit manufacturing techniques, can indicate when charge on battery departs from preset level. Membrane on switch is exposed to internal pressure of battery, which varies according to stored charge. When pressure varies from preset level, switch can turn on a light-emitting diode or similar indicator to warn user that battery is low.

Abita, J. L.↗

NASA NTRS1976

Viking lander spacecraft battery

The Viking Lander was the first spacecraft to fly a sterilized nickel-cadmium battery on a mission to explore the surface of a planet. The significant results of the battery development program from its inception through the design, manufacture, and test of the flight batteries which were flown on the two Lander spacecraft are documented. The flight performance during the early phase of the mission is also presented.

Newell, D. R.↗

NASA NTRS2002

The 2001 NASA Aerospace Battery Workshop

This document contains the proceedings of the 34th annual NASA Aerospace Battery Workshop, hosted by the Marshall Space Flight Center, November 27-29, 2001. The workshop was attended by scientists and engineers from various agencies of the US Government, aerospace contractors, and battery manufacturers, as well as international participation in like kind. The subjects covered included nickel-hydrogen, nickel-cadmium, lithium-ion, and silver-zinc technologies.

Brewer, Jeff C.↗

NASA NTRS2026

Investigating Dual Electrospinning as a Means of Enhancing Passive Thermal Control Coatings for Cryogenic Propellant Storage in Extraterrestrial Environments

Passive thermal control is necessary as space exploration becomes increasingly widespread. Materials with superior optical properties (high solar reflectance and infrared emittance) are critical for passive thermal control because they can reject most of the incident solar radiation and promote thermal emission from cryogenic propellant storage tanks, enabling the extraterrestrial storage of cryogens. We have demonstrated in previous studies that electrospun nanofibers exhibit exceptional optical properties, offering significant benefits for passive radiative cooling in space. Particularly, electrospun polyvinylidene fluoride-co-hexafluoropropylene PVDF-HFP nanofibers demonstrate exceptionally high solar reflectance (>99%) and strong thermal emittance (measured at ~300 K). However, they exhibit nanostructural changes in the presence of atomic oxygen, which is prevalent in Low Earth Orbit. This study focuses on creating a unique blend of polymeric (PVDF-HFP) and ceramic-based (silica) nanofibers by leveraging the chemical stability and atomic oxygen resistance of silica, using the dual electrospinning manufacturing method. This approach aims to preserve the structural properties of the polymeric counterpart without compromising its optical performance, thereby providing an innovative method for manufacturing environmentally resilient passive thermal control nanofibers with desirable optical and thermal control functionalities for extraterrestrial storage of cryogenic propellants.

Chieloka Ibekwe↗