Search NASA⌕ Search

SEARCH · Search NASA

Results for “area compressibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Comparative Life Cycle Assessment of Injection Molded and Big Area Additive Manufactured NdFeB Bonded Permanent Magnets

Permanent magnets are expected to play a crucial role in the realization of the clean economy. In particular, the neodymium-iron-boron (Nd2Fe14B or NdFeB) magnets, which have the highest energy density among rare earth permanent magnets, are needed for building more efficient windmill generators, electric vehicle motors, etc. Currently, near-net shape magnets can be either made through sintering and compression molding with extensive post machining or directly through injection molding. However, injection molding has a loading volume fraction limitation of 0.65 for nylon binders. A novel method of manufacturing bonded permanent magnets with loading fraction greater than 0.65 has been demonstrated using Big Area Additive Manufacturing (BAAM) printers. As energy density is directly proportional to the square of the magnet loading fraction, magnets produced using BAAM printers require less volume and magnetic material compared to that of injection molded magnets on average. A comparative LCA shows that this difference in magnetic powder consumption nearly constitutes the difference in the environmental impact categories. Even after assuming recycled magnetic input, the BAAM magnets perform better environmentally than injection molded magnets, especially in the ozone depletion category. Since BAAM printers can accommodate even higher loading fractions, at scale, BAAM printers possibly can bring about a significant decrease in rare earth mineral consumption and environmental emissions. So furthermore, single screw extrusion enables BAAM printers to have high print speeds and allow them to be economically competitive against injection molding. Therefore, BAAM printed magnets show promise in transitioning towards the clean economy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Model 9975 O Ring Fixture LongTerm Leak Performance (FY2021 Status Report)

Leak testing experiments to monitor the aging performance of Viton® GLT and GLT-S O-rings used in the model 9975 shipping package has been ongoing since 2004 at Savannah River National Laboratory. Seventy tests using mock-up 9975 primary containment vessels (PCVs) with GLT O-rings were assembled and heated to temperatures ranging from 200 to 450 °F. Due to material substitution, fourteen tests with GLT-S O-rings were initiated in 2008 and heated to temperatures ranging from 200 to 400 °F. The conditioning temperatures are elevated compared to the calculated maximum O-ring temperature in a 9975 package in storage, 158 °F, to accelerate aging and enable observations of O-ring failures in a reasonable time frame. The fixtures are leak tested periodically and all GLT O-ring fixtures aging at 350 °F or above have failed to maintain a leak-tight seal. Eight GLT O-ring fixtures aging at 300 °F have failed after 2.8 to 5.7 years at temperature while the remaining fixtures at 300 °F were retired from testing following more than five years without failure. There has been one GLT O-ring fixture which failed after 13.4 years aging at 200 °F. However, 19 other GLT O-rings aging at 200 °F have remained leak-tight for over 14 years and remain in test. No failures have yet been observed in GLT O-ring fixtures aging at 270 °F for 9.5 years. All GLT-S O-ring fixtures aging at 300 °F or above have failed their leak test. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 and 250 °F for 11.5 years. Data from the O-ring fixtures are generally consistent with results from compression stress-relaxation testing, and provide confidence in the predictive models based on those results. However, uncertainty exists in extrapolating these elevated temperature results to the lower temperatures of interest for normal storage in K-Area Complex (KAC). Oxygen consumption testing, which includes results from temperatures near KAC normal storage temperatures, is ongoing to provide further confidence and corroborate these extrapolations. The collective data from these test efforts suggest the minimum O-ring service life at KAC normal storage conditions should be at least 34 years for GLT and GLT-S O-rings. Measurement of compression set in O-rings removed from failed fixtures, compared to that from KAC surveillance O-rings, indicate significant margin remains for O-rings still in service in 9975 packages in KAC. Aging and periodic leak testing will continue for the remaining 26 mock-up PCV fixtures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Model 9975 O-Ring Fixture Long-Term Leak Performance (FY2022 Status Report)

Leak testing experiments to monitor the aging performance of Viton® GLT and GLT-S O-rings used in the model 9975 shipping package has been ongoing since 2004 at Savannah River National Laboratory. Seventy tests using mock-up 9975 primary containment vessels (PCVs) with GLT O-rings were assembled and heated to temperatures ranging from 200 to 450 °F. Due to material substitution, fourteen tests with GLT-S O-rings were initiated in 2008 and heated to temperatures ranging from 200 to 400 °F. The conditioning temperatures are elevated compared to the calculated maximum O-ring temperature in a 9975 package in storage, 158 °F, to accelerate aging and enable observations of O-ring failures in a reasonable time frame. The fixtures are leak tested periodically and all GLT O-ring fixtures aging at 350 °F or above have failed to maintain a leak-tight seal. Eight GLT O-ring fixtures aging at 300 °F have failed after 2.8 to 5.7 years at temperature while the remaining fixtures at 300 °F were retired from testing following more than five years without failure. There has been one GLT O-ring fixture which failed after 13.4 years aging at 200 °F. However, 20 other GLT O-rings aging at 200 °F have remained leak-tight for over 14 years and remain in test. No failures have yet been observed in GLT O-ring fixtures aging at 270 °F for 10.4 years. All GLT-S O-ring fixtures aging at 300 °F or above have failed their leak test. No failures have yet been observed in GLT-S O-ring fixtures aging at 250 °F for 12.5 years. This year, one GLT-S O-ring fixture failed after 12.4 years aging at 200 °F. Data from the O-ring fixtures are generally consistent with results from compression stress-relaxation testing, and provide confidence in the predictive models based on those results. However, uncertainty exists in extrapolating these elevated temperature results to the lower temperatures of interest for normal storage in K-Area Complex (KAC). Oxygen consumption testing, which includes results from temperatures near KAC normal storage temperatures, is ongoing to provide further confidence and corroborate these extrapolations. The collective data from these test efforts suggest the minimum O-ring service life at KAC normal storage conditions should be at least 34 years for GLT and GLT-S O-rings. Measurement of compression set in O-rings removed from failed fixtures, compared to that from KAC surveillance O-rings, indicate significant margin remains for O-rings still in service in 9975 packages in KAC. Aging and periodic leak testing will continue for the remaining 25 mock-up PCV fixtures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of cyber attacks on distributed compressive sensing based state estimation in power distribution grids

Modern power distribution grids suffer from multiple vulnerabilities due to the tight integration between the physical system and the cyber infrastructure. Sophisticated and malicious cyber attacks continue to adversely impact the grid operation leading to performance degradation, service interruption, and grid failure. State estimation plays an essential role in grid monitoring and advancing cyber-attack situational awareness. In this regard, this paper first proposes a distributed compressive sensing (CS) state estimation approach for an unobservable distribution grid. Further, the proposed distributed CS approach divides the distribution grid into sub-areas to perform local state estimation. Then an alternating direction method of multipliers (ADMM) based iterative information exchange among neighboring areas is employed to complete the estimation process. In this estimation process, the impact of loss of measurement data, false data injection (FDI), replay, and neighborhood cyber-attacks is analyzed. Extensive simulations are performed on the IEEE 37-bus and IEEE 123-bus standard networks to demonstrate the algorithm’s robustness to the aforementioned cyber-attacks. A quantitative analysis of computational complexity and simulation time of the distributed CS based approach is also presented.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Spinning metasurface stack for spectro-polarimetric thermal imaging

Spectro-polarimetric imaging in the long-wave infrared (LWIR) region plays a crucial role in applications from night vision and machine perception to trace gas sensing and thermography. However, the current generation of spectro-polarimetric LWIR imagers suffers from limitations in size, spectral resolution, and field of view (FOV). While meta-optics-based strategies for spectro-polarimetric imaging have been explored in the visible spectrum, their potential for thermal imaging remains largely unexplored. In this work, we introduce an approach for spectro-polarimetric decomposition by combining large-area stacked meta-optical devices with advanced computational imaging algorithms. The co-design of a stack of spinning dispersive metasurfaces along with compressive sensing and dictionary learning algorithms allows simultaneous spectral and polarimetric resolution without the need for bulky filter wheels or interferometers. Our spinning-metasurface-based spectro-polarimetric stack is compact (<10×10×10cm) and robust, and it offers a wide field of view (20.5°). We show that the spectral resolving power of our system substantially enhances performance in machine learning tasks such as material classification, a challenge for conventional panchromatic thermal cameras. Our approach represents a significant advance in the field of thermal imaging for a wide range of applications including heat-assisted detection and ranging (HADAR).

Optics↗
DOE OSTI2021

Degradation Studies of Silicone Rubbers in Direct Contact with Corrosive Solids Under Compression

Silicone elastomers are polymer materials widely used within the complex, serving as cushions, adhesives, binders, and potting compounds. Excellent high-temperature resistance combined with low-temperature flexibility, high resistance to chemicals and long-term age-related stability, make silicones first-choice materials in many application areas. However, the siloxane bonds comprising the backbone of silicone elastomers are susceptible to hydrolysis when catalytic amounts of acid or base are present. Hydrolysis is a form of degradation that results in chain-cleavage and rearrangement reactions, which can manifest in changes to the physical response and mechanical properties of the elastomer. This task aims to assess and quantify the extent of degradation and/or corrosion of silicone elastomer materials when placed in direct compressive contact with an Arrhenius base under varying environments (oxidative/nonoxidative, relative humidity, temperature, time, etc.).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multiscale Modeling Framework Using Element‐Based Galerkin Methods for Moist Atmospheric Limited‐Area Simulations

This paper presents a multiscale modeling framework (MMF) to model moist atmospheric limited-area weather. The MMF resolves large-scale convection using a coarse grid while simultaneously resolving local features through numerous fine local grids and coupling them seamlessly. Both large- and small-scale processes are modeled using the compressible Navier-Stokes equations within the Nonhydrostatic Unified Model of the Atmosphere (NUMA), and are discretized using a continuous element-based Galerkin method (spectral elements) with high-order basis functions. Consequently, the large-scale and small-scale models share the same dynamical core but have the flexibility to be adjusted individually. The proposed MMF method is tested in 2D and 3D idealized limited-area weather problems involving storm clouds produced by squall line and supercell simulations. Numerical results from the MMF showed enhanced representation of cloud processes compared to the coarse model.

Kang, Soonpil [Naval Postgraduate School, Monterey↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, Part II: Representing interparticle comminution by K COMP

An applied and empirical compaction fracture resistance parameter, K COMP , was developed to represent the compression-induced interparticle-comminution response of granular brittle materials (e.g., ceramic or glass particles). The development of K COMP is an outcome from Part I of this three-paper series. The K COMP represents a continuum response of compaction fracture resistance and was adapted from established Griffith linear elastic fracture mechanics theory. From that, the K COMP relates macroscopically applied compressive stress to a corresponding inverse-square-root representative particle size, where the latter is estimated from an entire particle size distribution or specific surface area measurement. In conclusion, the K COMP value was not constant over a wide range of stresses for all examined brittle granular materials, and this is indicative of a change in the dominant mode of permanent deformation at higher compaction stresses.

brittle↗
DOE OSTI2023

Investigating Combinations of Alkali Metal Oxides and Hydrogenation Catalysts for Reactive Capture of CO2 to Useful C1 Products

As the world endures environmental crises associated with climate change and the rise of atmospheric CO2 concentrations from anthropogenic CO2 emission, carbon capture and utilization (CCU) technologies are increasingly necessary. Reactive carbon capture (RCC) technologies, in which capture and conversion of CO2 occur in a single reactor, are more energetically and economically attractive by avoiding the need to purify, compress, and transport the captured CO2. To this end, dual function materials (DFMs) - composed of sorbents and catalysts co-dispersed on the same high surface area carrier - have been developed. The sorbent component allows for selective capture of CO2 from a gas stream and the catalyst component subsequently performs the in-situ conversion of the adsorbed CO2 upon introduction of a reactive gas (typically H2). The end product of the most established DFM, comprised of Ru and/or Ni with an alkaline sorbent, is methane via the CO2 methanation reaction. While renewable methane would be an excellent transition fuel, fossil methane is inexpensive (averaging $2.57/MMBTU in pre-pandemic 2019) and the economics of renewable methane utilization are noncompetitive. This requires the design and investigation of DFMs that enable CO2 capture and conversion to more valuable and more useful C1 products like CO or methanol (average price of methanol was $20.61/MMBTU in pre-pandemic 2019). These products can then be further upgraded to high energy density synthetic fuels, and related carbonaceous products, for more sustainable alternatives in industries that are difficult to decarbonize, specifically heavy duty vehicles and aviation. Herein, we report various sorbent + catalyst combinations to achieve the production of useful C1 products through reactive capture of CO2.

carbon capture↗
DOE OSTI2023

Imaging velocity interferometer system for any reflector (VISAR) diagnostics for high energy density sciences

Two variants of optical imaging velocimetry, specifically the one-dimensional streaked line-imaging and the two-dimensional time-resolved area-imaging versions of the Velocity Interferometer System for Any Reflector (VISAR), have become important diagnostics in high energy density sciences, including inertial confinement fusion and dynamic compression of condensed matter. Here, we give a brief review of the historical development of these techniques, then describe the current implementations at major high energy density (HED) facilities worldwide, including the OMEGA Laser Facility and the National Ignition Facility. We illustrate the versatility and power of these techniques by reviewing diverse applications of imaging VISARs for gas-gun and laser-driven dynamic compression experiments for materials science, shock physics, condensed matter physics, chemical physics, plasma physics, planetary science and astronomy, as well as a broad range of HED experiments and laser-driven inertial confinement fusion research.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Direct growth of crystalline SiGe nanowires on superconducting NbTiN thin films

Novel heterostructures created by coupling one-dimensional semiconductor nanowires with a superconducting thin film show great potential toward next-generation quantum computing. Here, by growing high-crystalline SiGe nanowires on a NbTiN thin film, the resulting heterostructure exhibits Ohmic characteristics as well as a shift of the superconducting transition temperature (T c ). The structure was characterized at atomic resolution showing a sharp SiGe/NbTiN interface without atomic interdiffusion. Lattice spacing, as calculated from large-area x-ray diffraction experiments, suggests a potential preferred d-spacing matching between (200) NbTiN and (110) SiGe grains. The observed out-of-plane compressive strain within the NbTiN films coupled with SiGe nanowires explains the downward shift of the superconductivity behavior. The presented results post scientific insights toward functional heterostructures by coupling multi-dimensional materials, which could enable tunable superconductivity that benefits the quantum science applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Amphiphilic Baskets for Supramolecular Nanoarchitectures at Interfaces: Inverted Monolayer Formation on Water

Interfacial chemistry of molecular baskets remains poorly understood despite their promise for supramolecular applications of detection and sequestration of toxic molecules including those of illicit drugs, organophosphorus compounds, and anticancer agents. We present a fundamental investigation of the interfacial behavior of three amphiphilic supramolecular baskets (ASB 4, 8, and 12), having increasingly longer yet linear alkyl chains at the top of their bowl-shaped cavity. The studies were completed at the air−water interface to elucidate surface activity, interfacial stability, self-assembly, and monolayer organization that drive inverted monolayer formation, in which the molecular arms orient toward the aqueous phase in a configuration opposite to that typically observed for lipids. Herein, surface pressure−area isotherms of ASB 4, 8, 12, deposited on a water surface, were performed in tandem with nonequilibrium relaxation experiments to quantify surface activity, thermodynamic stability, and monolayer compressibility of the baskets’ monolayer assembly. Brewster angle microscopy enabled direct visualization of morphological evolution, aggregation, and packing at the interface. We show that systematic extension of the hydrocarbon arms, from four to 12 methylene groups, progressively modifies intermolecular packing, drives distinct two-dimensional aggregation pathways, and increases number densities at the air−water interface. Atomistic molecular dynamics simulations corroborate many of these experimentally observed trends and provide mechanistic detail on the cooperative roles of basket topology and interfacial concentration in regulating the hydration structure and dynamics within the cavities generated by surface-adsorbing baskets, consistent with observed variations in surface activity and packing. Our results establish how the topology of these unique supramolecules and their concentration govern interfacial organization and offer a rational framework for designing amphiphiles with predictable behavior at soft interfaces.

Hydrocarbons↗
DOE OSTI2022

U.S. Industrial and Commercial Motor System Market Assessment Report. Volume 3: Energy Saving Opportunity

This report seeks to inform the potential for motor systems to support decarbonization by estimating their potential energy, electricity cost, and CO 2 emissions reduction potential from adoption of proven energy efficiency actions and advanced technologies. This is the third and final report in a series of reports disseminating the findings of the U.S. Department of Energy’s (DOE’s) Motor System Market Assessment (MSMA). The MSMA and this report focus on polyphase motor systems greater than or equal to 1 horsepower (hp) in the industrial and commercial sectors. In the U.S. Industrial and Commercial Motor System Market Assessment Report Volume 1: Characteristics of the Installed Base (Volume 1 report), it was determined that these motor systems consume more than 1,000 terawatt-hours (TWh) annually. This equates to 29% of the U.S. electric grid load and results in 765 million metric tons (MMT) of CO 2 emissions and $166 billion in electricity costs. This report finds that substantial reductions to these energy, cost, and emissions impacts are possible, with three areas of significant opportunity being (1) improved load matching, (2) replacing older inefficient motors with more efficient motors, and (3) improving the condition of fluid (e.g., air, water, compressed air) distribution systems. A summary of the savings potential from these three opportunities placed within the context of the overall consumption for motor systems is illustrated in Figure ES 1 (industrial) and Figure ES 2 (commercial).

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Volumetrics of Hydrogen Storage by Physical Adsorption

Physical adsorption remains a promising method for achieving fast, reversible hydrogen storage at both ambient and cryogenic conditions. Research in this area has recently shifted to focus primarily on the volumetric (H 2 stored/delivered per volume) gains achieved within an adsorptive storage system over that of pure H 2 compression; however, the methodology for estimating a volumetric stored or delivered amount requires several assumptions related to the ultimate packing of the adsorbent material into an actual storage system volume. In this work, we critically review the different assumptions commonly employed, and thereby categorize and compare the volumetric storage and delivery across numerous different porous materials including benchmark metal-organic frameworks, porous carbons, and zeolites. In several cases, there is a significant gain in both storage and delivery by the addition of an adsorbent to the high-pressure H 2 storage system over that of pure compression, even at room temperature. Lightweight, low-density materials remain the optimal adsorbents at low temperature, while higher density, open metal-containing frameworks are necessary for high-density room temperature storage and delivery.

08 HYDROGEN↗
DOE OSTI2021

Applying design principles to improve hydrogen storage capacity in nanoporous materials

Hydrogen is an attractive option for energy storage because it can be produced from renewable sources and produces environmentally benign byproducts. However, the volumetric energy density of molecular hydrogen at ambient conditions is low compared to other storage methods like batteries, so it must be compressed to attain a viable energy density for applications such as transportation. Nanoporous materials have attracted significant interest for gas storage because they can attain high storage density at lower pressure than conventional compression. Here, we examine how to improve the cryogenic hydrogen storage capacity of a series of porous aromatic frameworks (PAFs) by controlling the pore size and increasing the surface area by adding functional groups. We also explore tradeoffs in gravimetric and volumetric measures of the hydrogen storage capacity and the effects of temperature swings using grand canonical Monte Carlo simulations. We also consider the effects of adding functional groups to the metal–organic framework NU-1000 to improve its hydrogen storage capacity. We find that highly flexible alkane chains do not improve the hydrogen storage capacity in NU-1000 because they do not extend into the pores; however, rigid chains containing alkyne groups do increase the surface area and hydrogen storage capacity. Finally, we demonstrate that the deliverable capacity of hydrogen in NU-1000 can be increased from 40.0 to 45.3 g/L (at storage conditions of 100 bar and 77 K and desorption conditions of 5 bar and 160 K) by adding long, rigid alkyne chains into the pores.

08 HYDROGEN↗
DOE OSTI2025

High-current-density electrosynthesis of formate from captured CO 2 solution by MOF-derived bismuth nanosheets

Greenhouse gas emissions present a significant challenge to humanity, and utilizing renewable electricity to convert emitted CO 2 into value-added products offers a promising solution; however, traditional CO 2 capture and regeneration processes remain energy-intensive, restricting the overall system efficiency and decarbonization efficacy. In this study, an advanced direct reduction of captured CO 2 with large current densities for formate electrosynthesis was demonstrated without the need for CO 2 regeneration or compression. The bismuth nanosheet (DRM-BiNS) was synthesized by direct reduction of a Bi-based MOF, representing a new class of catalytic materials with a large surface area and interconnected pores, suitable for the direct reduction of captured CO 2 . By seamlessly combining experimentation and simulation, insights into the structure-parameter-performance relation were acquired in a flow cell setting, including critical membrane-electrode distance, cell orientation, and pumping flow rate. Important flow-cell components, such as catholyte volume, electrode substrate, membrane choice, and ionomer type, were also carefully examined to enhance the cell performance. In sharp contrast to prior studies limited to current densities below 20 mA/cm 2 in bicarbonate-based captured CO 2 solutions, this work demonstrates a remarkable current density of 300 mA/cm 2 with an FE to formate comparable to the case with gas-fed CO 2 reduction. Moreover, the process sustained an FE above 50% at a high current density of 500 mA/cm 2 . The DRM-BiNS catalyst exhibited outstanding selectivity, activity, and stability, significantly outperforming oxide-derived bismuth nanosheets (OD-BiNS) in captured CO 2 reduction. Furthermore, these findings offer critical insights into the development of sustainable and scalable CO 2 utilization technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Experimental characterization of a section of a spherically imploding plasma liner formed by merging hypersonic plasma jets

In this work, we report experimental results on merging of hypersonic plasma jets, which is the fundamental building block for forming spherically imploding plasma liners as a potential standoff compression driver for magneto-inertial fusion. Jets are formed and launched by contoured-gap coaxial plasma guns mounted at the six vertices and the center of a hexagon covering approximately one-tenth of the surface area of a 9-ft-diameter spherical chamber. First, from experiments with two and three merging jets of four different species (N, Ar, Kr, and Xe), we show that (1) density spatial non-uniformities can be large (with electron-density jumps ranging from 2.9 for N to 6.6 for Xe) when shocks form upon jet merging, but smaller (density jumps <2) when shocks do not form; (2) jet impurities (20% Ti in these experiments) can increase the level of density spatial non-uniformity by increasing the collisionality of jet merging, leading to shock formation rather than potentially more desirable shockless jet merging; and (3) the liner Mach number can remain high (≳10), as required for plasma liners to be an effective compression driver. Secondly, from experiments with six and seven merging jets using Ar, we present results with improved jet-to-jet mass balance of <2% across jets, including (1) evidence of substantially increased balance in the jet merging and symmetry of the liner structure and (2) potentially favorable changes in the jet-merging morphology with the addition of the seventh jet. Ultimately, for both experiments, we present comparisons between experimental and synthetic data from three-dimensional hydrodynamic codes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗