SEARCH · Search NASA

Results for “area optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Comparing Satellite Rainfall Estimates with Rain-Gauge Data: Optimal Strategies Suggested by a Spectral Model

Validation of satellite remote-sensing methods for estimating rainfall against rain-gauge data is attractive because of the direct nature of the rain-gauge measurements. Comparisons of satellite estimates to rain-gauge data are difficult, however, because of the extreme variability of rain and the fact that satellites view large areas over a short time while rain gauges monitor small areas continuously. In this paper, a statistical model of rainfall variability developed for studies of sampling error in averages of satellite data is used to examine the impact of spatial and temporal averaging of satellite and gauge data on intercomparison results. The model parameters were derived from radar observations of rain, but the model appears to capture many of the characteristics of rain-gauge data as well. The model predicts that many months of data from areas containing a few gauges are required to validate satellite estimates over the areas, and that the areas should be of the order of several hundred km in diameter. Over gauge arrays of sufficiently high density, the optimal areas and averaging times are reduced. The possibility of using time-weighted averages of gauge data is explored.

Bell, Thomas L.↗

NASA NTRS2009

Initial Concept for Terminal Area Conflict Detection, Alerting, and Resolution Capability on or Near the Airport Surface

The Next Generation Air Transportation System (NextGen) concept for 2025 envisions the movement of large numbers of people and goods in a safe, efficient, and reliable manner. The NextGen will remove many of the constraints in the current air transportation system, support a wider range of operations, and deliver an overall system capacity up to 3 times that of current operating levels. In order to achieve the NextGen vision, research is necessary in the areas of surface traffic optimization, maximum runway capacity, reduced runway occupancy time, simultaneous single runway operations, and terminal area conflict prevention, among others. The National Aeronautics and Space Administration (NASA) is conducting Collision Avoidance for Airport Traffic (CAAT) research to develop technologies, data, and guidelines to enable Conflict Detection and Resolution (CD&R) in the Airport Terminal Maneuvering Area (ATMA) under current and emerging NextGen operating concepts. In this report, an initial concept for an aircraft-based method for CD&R in the ATMA is presented. This method is based upon previous NASA work in CD&R for runway incursion prevention, the Runway Incursion Prevention System (RIPS). CAAT research is conducted jointly under NASA's Airspace Systems Program, Airportal Project and the Aviation Safety Program, Integrated Intelligent Flight Deck Project.

Green, David F.↗

NASA NTRS2013

Initial Concept for Terminal Area Conflict Detection, Alerting, and Resolution Capability On or Near the Airport Surface, Version 2.0

The Next Generation Air Transportation System (NextGen) concept for 2025 envisions the movement of large numbers of people and goods in a safe, efficient, and reliable manner. The NextGen will remove many of the constraints in the current air transportation system, support a wider range of operations, and deliver an overall system capacity up to 3 times that of current operating levels. In order to achieve the NextGen vision, research is necessary in the areas of surface traffic optimization, maximum runway capacity, reduced runway occupancy time, simultaneous single runway operations, and terminal area conflict prevention, among others. The National Aeronautics and Space Administration (NASA) is conducting Collision Avoidance for Airport Traffic (CAAT) research to develop technologies, data, and guidelines to enable Conflict Detection and Resolution (CD&R) in the Airport Terminal Maneuvering Area (ATMA) under current and emerging NextGen operating concepts. The term ATMA was created to reflect the fact that the CD&R concept area of operation is focused near the airport within the terminal maneuvering area. In the following, an initial concept for an aircraft-based method for CD&R in the ATMA is presented. This method is based upon previous NASA work in CD&R for runway incursion prevention, the Runway Incursion Prevention System (RIPS).

Otero, Sharon D.↗

NASA NTRS1972

Optimal horizontal guidance law for aircraft in the terminal area.

Study of the horizontal guidance of aircraft in and near the terminal area. The problem of guiding an aircraft in minimum time from an arbitrary point to the outer marker is formulated as a nonlinear optimal control problem, and the control law solution is obtained by the application of the maximum principle. It is found that for some initial states the problem is singular. Furthermore, the extremal controls for this problem are not unique. Consequently, the optimal controls must be obtained on the basis of the value of the performance index. The control law is implemented in the form of a digital computer program which computes the optimal trajectory for arbitrary initial conditions.

Pecsvaradi, T.↗

NASA NTRS1997

Optimal Trajectories for the Helicopter in One-Engine-Inoperative Terminal-Area Operations

This paper presents a summary of a series of recent analytical studies conducted to investigate one-engine-inoperative (OEI) optimal control strategies and the associated optimal trajectories for a twin engine helicopter in Category-A terminal-area operations. These studies also examine the associated heliport size requirements and the maximum gross weight capability of the helicopter. Using an eight states, two controls, augmented point-mass model representative of the study helicopter, continued takeoff (CTO), rejected takeoff (RTO), balked landing (BL), and continued landing (CL) are investigated for both vertical-takeoff-and-landing (VTOL) and short-takeoff-and-landing (STOL) terminal-area operations. The formulation of the non-linear optimal control problems with considerations for realistic constraints, solution methods for the two-point boundary-value problem, a new real-time generation method for the optimal OEI trajectories, and the main results of this series of trajector optimization studies are presented. In particular, a new balanced-weight concept for determining the takeoff decision point for VTOL Category-A operations is proposed, extending the balanced-field length concept used for STOL operations.

Chen, Robert T. N.↗

NASA NTRS1974

Study of genetic direct search algorithms for function optimization

The results are presented of a study to determine the performance of genetic direct search algorithms in solving function optimization problems arising in the optimal and adaptive control areas. The findings indicate that: (1) genetic algorithms can outperform standard algorithms in multimodal and/or noisy optimization situations, but suffer from lack of gradient exploitation facilities when gradient information can be utilized to guide the search. (2) For large populations, or low dimensional function spaces, mutation is a sufficient operator. However for small populations or high dimensional functions, crossover applied in about equal frequency with mutation is an optimum combination. (3) Complexity, in terms of storage space and running time, is significantly increased when population size is increased or the inversion operator, or the second level adaptation routine is added to the basic structure.

Zeigler, B. P.↗

NASA NTRS1987

Optimization of orbital assignment and specification of service areas in satellite communications

The mathematical nature of the orbital and frequency assignment problem for communications satellites is explored, and it is shown that choosing the correct permutations of the orbit locations and frequency assignments is an important step in arriving at values which satisfy the signal-quality requirements. Two methods are proposed to achieve better spectrum/orbit utilization. The first, called the delta S concept, leads to orbital assignment solutions via either mixed-integer or restricted basis entry linear programming techniques; the method guarantees good single-entry carrier-to-interference ratio results. In the second, a basis for specifying service areas is proposed for the Fixed Satellite Service. It is suggested that service areas should be specified according to the communications-demand density in conjunction with the delta S concept in order to enable the system planner to specify more satellites and provide more communications supply.

Wang, Cou-Way↗

NASA NTRS1980

Flat-plate photovoltaic array design optimization

An analysis is presented which integrates the results of specific studies in the areas of photovoltaic structural design optimization, optimization of array series/parallel circuit design, thermal design optimization, and optimization of environmental protection features. The analysis is based on minimizing the total photovoltaic system life-cycle energy cost including repair and replacement of failed cells and modules. This approach is shown to be a useful technique for array optimization, particularly when time-dependent parameters such as array degradation and maintenance are involved.

Ross, R. G., Jr.↗

NASA NTRS1991

New displacement-based methods for optimal truss topology design

Two alternate methods for maximum stiffness truss topology design are presented. The ground structure approach is used, and the problem is formulated in terms of displacements and bar areas. This large, nonconvex optimization problem can be solved by a simultaneous analysis and design approach. Alternatively, an equivalent, unconstrained, and convex problem in the displacements only can be formulated, and this problem can be solved by a nonsmooth, steepest descent algorithm. In both methods, the explicit solving of the equilibrium equations and the assembly of the global stiffness matrix are circumvented. A large number of examples have been studied, showing the attractive features of topology design as well as exposing interesting features of optimal topologies.

Bendsoe, Martin P.↗

NASA NTRS2014

Development of Super Ensemble-Based Aviation Turbulence Guidance (SEATG) for Air Traffic Management

A new method for forecasting turbulence is developed and evaluated using the high resolution weather model and in situ turbulence observations from commercial aircraft. The new method is an ensemble of various turbulence metrics from multiple time-lagged ensemble forecasts created using a sequence of four procedures. These include weather modeling, calculation of turbulence metrics, mapping the metrics into a common turbulence-scale, and production of final forecast. The new method uses similar methodology as current operational turbulence forecast with three improvements. First, it uses a higher resolution ((delta)x = 3 km) weather model to capture cloud resolving scale phenomena. Second, it computes the metrics for multiple forecasts that are combined at the same valid time resulting in a time-lagged ensemble of multiple turbulence metrics. Finally, it provides both deterministic and probabilistic turbulence forecasts. Results show the new forecasts match well with observed radar reflectivity along a surface front as well as convectively induced turbulence outside the clouds on research period. Overall performance skill of the new turbulence forecast compared with the observed EDR data during the research period is superior to any single turbulence metric. The probabilistic turbulence forecast is used in an example air traffic management application for creating a wind-optimal route considering turbulence information. The wind-optimal route passing through areas of 50% potential for moderate-or-greater turbulence and the lateral turbulence avoidance routes starting from three different waypoints along the wind-optimal route from Los Angeles international airport to John F. Kennedy international airport are calculated using different turbulence forecasts. This example shows additional flight time is required to avoid potential turbulence encounters.

modeling↗

NASA NTRS1999

NASA Aeronautics Multidisciplinary Analysis and Design Fellowship Program

This program began as a grant from NASA Headquarters, NGT-10025, which was in effect from 10/l/93 until 10/31/96. The remaining funding for this effort was transferred from NASA Headquarters to NASA Langley and a new grant NGT-1-52155 was issued covering the period II/l/96 to 5/15/99. This report serves as the final report of NGT-1-52155. For a number of years, Virginia Tech had been on the forefront of research in the area of multidisciplinary analysis and design. In June of 1994, faculty members from aerospace and ocean engineering, engineering science and mechanics, mechanical engineering, industrial engineering, mathematics and computer sciences, at Virginia Tech joined together to form the Multidisciplinary Analysis and Design (MAD) Center for Advanced Vehicles. The center was established with the single goal: to perform research that is relevant to the needs of the US industry and to foster collaboration between the university, government and industry. In October of 1994, the center was chosen by NASA headquarters as one of the five university centers to establish a fellowship program to develop a graduate program in multidisciplinary analysis and design. The fellowship program provides full stipend and tuition support for seven U. S. students per year during their graduate studies. The grant is currently being administered by the NMO Branch of NASA Langley. To advise us regarding the problems faced by the industry, an industrial advisory board has been formed consisting of representatives from industry as well as government laboratories. The present membership includes major aerospace companies: Aurora Flight Sciences, Boeing: Philadelphia, Boeing: Long Beach, Boeing: Seattle, Boeing: St. Louis, Cessna, Ford, General Electric, Hughes, Lockheed-Martin: Palo Alto, Northrop-Grumman, Sikorsky, smaller, aerospace software companies: Aerosoft, Phoenix Integration and Proteus Engineering, along with representatives from government agencies, including: NASA Ames, Langley and Lewis. The function of the advisory board is to channel information from its member companies to faculty members concerning problems that need research attention in the general area of multidisciplinary design optimization (MDO). The faculty and their graduate students make presentations to the board on their research. The board makes recommendations on the research and suggests new areas and problems which need attention. Many students participating in the program spend 3-6 months in industry working on their research projects. We are completing the fifth year of the fellowship program and have had four advisory board meetings in Blacksburg. Ten students have spent the three month periods in industry. In addition to the research element of the MAD Center efforts we also have an academic component. We have developed a menu of design-related graduate courses and two new courses: one in Aerospace Manufacturing and another in MDO. Some of the MAD Center activities are described on the world-wide web at http://www.aoe.vt.edu/mads.html The MAD Center represents an innovative approach for joint Industry-Government-University cooperation in the development of a comprehensive program in engineering education which addresses the design needs of industry. The following charts list detail of the grant: mission of the MAD center, faculty members, purpose of the advisory board, board members, summary of the graduate and undergraduate program, history of the fellowship program, mission of the fellowship program, requirements of MAD fellows, course requirements, students supported, advisory board participants, and MAD center research papers

Grossman, B.↗

NASA NTRS1989

Appendix: Results obtained to date

Optimization procedures are described for the rotor blade design process by integrating appropriate disciplines and accounting for important interactions among the disciplines. Progress is reported in the areas of aerodynamic performance optimization, dynamic optimization, optimum placement of tuning masses for vibration reduction, and structural optimization. Selected results from these activities are highlighted in this appendix.

Walsh, Joanne L.↗

NASA NTRS1980

Large area flexible solar array design for Space Shuttle application

A large area flexible solar array has been designed for Shuttle power augmentation. The solar array utilizes large area, low cost, weldable solar cells. The paper addresses how the unique requirements of this system are implemented into the design. Economic and reliability issues relating to the optimization of a large area, foldable solar array concomitant to the Shuttle/Orbiter system are reviewed.

Souza, C. J.↗

NASA NTRS1972

Optimal horizontal guidance law for aircraft in the terminal area.

A complete nonlinear control law is derived for guiding an aircraft in minimum time from an arbitrary initial position and heading to a prescribed terminal position and heading in the horizontal plane. The solution is obtained with the aid of the maximum principle, and is implemented by constructing a digital-computer program for the resulting switching logic.

Pecsvaradi, T.↗

NASA NTRS2004

Human Motion Tracking at Marshall Space Flight Center's Collaborative Engineering Center ANVIL

The installation and use of electromagnetic human motion trackers requires a specially designed and metal-free environment for optimal performance. Such an area is not readily available at the Marshall Space Flight Center Collaborative Engineering Center ANVIL. Our paper details a systems engineering approach to installing and operating Ascension Technologies Ethernet MotionStar tracking system in a sub-optimal environment, used with the JACK human computer model's motion capture capabilities. We also discuss how this system is integrated into the Marshall Space Flight Center's Human Engineering process.

Henderson, Steven J.↗

NASA NTRS1995

Optimal domain decomposition strategies

The primary interest of the authors is in the area of grid generation, in particular, optimal domain decomposition about realistic configurations. A grid generation procedure with optimal blocking strategies has been developed to generate multi-block grids for a circular-to-rectangular transition duct. The focus of this study is the domain decomposition which optimizes solution algorithm/block compatibility based on geometrical complexities as well as the physical characteristics of flow field. The progress realized in this study is summarized in this paper.

Yoon, Yonghyun↗

NASA NTRS1999

High-Area-Ratio Rocket Nozzle at High Combustion Chamber Pressure: Experimental and Analytical Validation

Experimental data were obtained on an optimally contoured nozzle with an area ratio of 1025:1 and on a truncated version of this nozzle with an area ratio of 440:1. The nozzles were tested with gaseous hydrogen and liquid oxygen propellants at combustion chamber pressures of 1800 to 2400 psia and mixture ratios of 3.89 to 6.15. This report compares the experimental performance, heat transfer, and boundary layer total pressure measurements with theoretical predictions of the current Joint Army, Navy, NASA, Air Force (JANNAF) developed methodology. This methodology makes use of the Two-Dimensional Kinetics (TDK) nozzle performance code. Comparisons of the TDK-predicted performance to experimentally attained thrust performance indicated that both the vacuum thrust coefficient and the vacuum specific impulse values were approximately 2.0-percent higher than the turbulent prediction for the 1025:1 configurations, and approximately 0.25-percent higher than the turbulent prediction for the 440:1 configuration. Nozzle wall temperatures were measured on the outside of a thin-walled heat sink nozzle during the test fittings. Nozzle heat fluxes were calculated front the time histories of these temperatures and compared with predictions made with the TDK code. The heat flux values were overpredicted for all cases. The results range from nearly 100 percent at an area ratio of 50 to only approximately 3 percent at an area ratio of 975. Values of the integral of the heat flux as a function of nozzle surface area were also calculated. Comparisons of the experiment with analyses of the heat flux and the heat rate per axial length also show that the experimental values were lower than the predicted value. Three boundary layer rakes mounted on the nozzle exit were used for boundary layer measurements. This arrangement allowed total pressure measurements to be obtained at 14 different distances from the nozzle wall. A comparison of boundary layer total pressure profiles and analytical predictions show good agreement for the first 0.5 in. from the nozzle wall; but the further into the core flow that measurements were taken, the more that TDK overpredicted the boundary layer thickness.

Jankovsky, Robert S.↗

NASA NTRS1988

An initiative in multidisciplinary optimization of rotorcraft

Described is a joint NASA/Army initiative at the Langley Research Center to develop optimization procedures aimed at improving the rotor blade design process by integrating appropriate disciplines and accounting for important interactions among the disciplines. The activity is being guided by a Steering Committee made up of key NASA and Army researchers and managers. The committee, which has been named IRASC (Integrated Rotorcraft Analysis Steering Committee), has defined two principal foci for the activity: a white paper which sets forth the goals and plans of the effort; and a rotor design project which will validate the basic constituents, as well as the overall design methodology for multidisciplinary optimization. The paper describes the optimization formulation in terms of the objective function, design variables, and constraints. Additionally, some of the analysis aspects are discussed and an initial attempt at defining the interdisciplinary couplings is summarized. At this writing, some significant progress has been made, principally in the areas of single discipline optimization. Results are given which represent accomplishments in rotor aerodynamic performance optimization for minimum hover horsepower, rotor dynamic optimization for vibration reduction, and rotor structural optimization for minimum weight.

Adelman, Howard M.↗