Results for “atomic processes” — Page 6

DOE OSTI2020

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

pressurized oxy-coal combustion, sub-micron ash ae↗

DOE OSTI2022

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Development of Powder Production Methods for Advanced LEU Fuel Concepts

A set of novel fuel concepts has been proposed for use in advanced low-enriched uranium (LEU) systems that utilize powder metallurgical methods for fabrication of the fuel forms. Preliminary tests demonstrated the ability to produce powder but did not yield the desired quality to be used as feedstock in these applications. This study seeks to establish an improved powder production method for uranium-based alloys and evaluate the parameters required to refine the particles produced by size and morphology. Powder samples were fabricated via atomization and analyzed for particle morphology utilizing sieving methods and scanning electron microscopy (SEM). Surrogate testing displayed improved performance in producing small (<250 µm) spherical particles, and initial tests demonstrated the initial capability to atomize uranium. Further work is required to refine the atomization process to produce high quality uranium microspheres.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1983

Theoretical studies of chromospheres and winds in cool stars

The formation of spectral lines in expanding spherical atmospheres was determined in a physically realistic way, taking into account multilevel atomic processes, partial frequency redistribution, and other non-LTE transfer effects that affect the formation of optically thick lines. The formation of MgII and Ca II circumstellar absorption lines in late type giants and supergiants is investigated. The radiative cooling rate as a function of density and temperature was calculated from the results of plane parallel chromospheric models and these results were used to approximate the radiative cooling in an extended wind. The run of temperature was calculated along with the density and velocity profiles. The most important prediction of these models is that a warm zone in the wind must exist as a result of the wave heating. Within this zone, the Ca II and Mg II atoms can be ionized to Ca III and Mg III, so that the gas is transparent in the resonance transitions.

Dupree, A.↗

DOE OSTI2022

Development of an Enhanced Radiation Physics Toolset for Modeling Spectral and Imaging Signatures in the Warm Dense Matter Experiments

Radiative and atomic processes in plasmas play a critical role in a wide variety of high energy density laboratory plasma (HEDLP) experiments. The emission, absorption, and transport of radiation can strongly affect the overall energetics and evolution of such plasmas. In addition, radiation-based diagnostics – including imaging, spectroscopy, and absolute flux measurements – are widely used to determine key features of HEDLPs. To advance our understanding of HEDLP science, it is vital to have high-fidelity computational physics tools that have well-tested radiation physics modeling, and that are readily accessible to researchers in the HEDLP community. Simulations play an extremely important role for planning and designing the experiments, as well as for post-experiment data analysis. Prism Computational Sciences develops software that is used by National Laboratories and universities (including five members of LaserNetUS network). Prominent examples of such research efforts include z-pinch and short-pulse laser experiments designed to study the basic physics of photoionized plasmas and photoionization fronts, as well as their application to astrophysical plasmas. The main effort was dedicated to the development of non-equilibrium equation-of-state (EOS) models within the HELIOS-CR code, a hydrodynamics code with inline collisional-radiative atomic kinetics. Gas cell experiments on Z and Omega demonstrated the importance of non-equilibrium effects on atomic kinetics in photoionized plasmas. Recent proof-of-principle experiments on Omega EP confirmed the advantages of using a short-pulse laser to create an intense radiation drive, leading to additional experiments being proposed. Photoionization front experiments at LLE also emphasizes the importance of radiation and atomic physics. In both studies, HELIOS-CR simulations played a crucial role in computing non-equilibrium opacities and ionization distributions. A newly developed non-LTE EOS model will help addressing possible non-equilibrium effects, on for example specific heat, and their influence in plasma evolution. Prism also implemented support for open-source atomic data generated by the Flexible Atomic Code. This allows researchers to generate custom atomic tables and use them within the complex framework of simulation tools developed by Prism. The ability to use open-source atomic data would be extremely valuable for hydrodynamics and spectroscopic simulations that include high-Z materials, e.g., picosecond x-ray pulse generation experiments. Support for new atomic structures was fully implemented, and the data can be used by all simulation tools developed at Prism: radiation-hydrodynamics, imaging and spectroscopy, EOS and opacity. The development resulted in a significant fidelity enhancement to the simulations tools developed by Prism that are currently used in other cutting-edge experiments including: opacity measurement experiments performed to both understand the basic radiative and atomic properties of plasmas as well as provide data for more accurately modeling the internal structure of the Sun and other stars, high-intensity short-pulse laser experiments performed to develop short-wavelength light sources for use as backlighters and to investigate fast ignition concepts for inertial fusion energy; capsule implosion experiments designed to develop inertial fusion as an energy source, etc.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Reinforcement Learning-Guided Long-Timescale Simulation of Hydrogen Transport in Metals

Diffusion in alloys is an important class of atomic processes. However, atomistic simulations of diffusion in chemically complex solids are confronted with the timescale problem: the accessible simulation time is usually far shorter than that of experimental interest. In this work, long-timescale simulation methods are developed using reinforcement learning (RL) that extends simulation capability to match the duration of experimental interest. Two special limits, RL transition kinetics simulator (TKS) and RL low-energy states sampler (LSS), are implemented and explained in detail, while the meaning of general RL are also discussed. As a testbed, hydrogen diffusivity is computed using RL TKS in pure metals and a medium entropy alloy, CrCoNi, and compared with experiments. The algorithm can produce counter-intuitive hydrogen-vacancy cooperative motion. We also demonstrate that RL LSS can accelerate the sampling of low-energy configurations compared to the Metropolis–Hastings algorithm, using hydrogen migration to copper (111) surface as an example.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Mitigating Heavy Ion Irradiation‐Induced Degradation in p‐type SnO Thin‐Film Transistors at Room Temperature

The study investigates the mitigation of radiation damage on p‐type SnO thin‐film transistors (TFTs) with a fast, room‐temperature annealing process. Atomic layer deposition is utilized to fabricate bottom‐gate TFTs of high‐quality p‐type SnO layers. After 2.8 MeV Au 4+ irradiation at a fluence level of 5.2 × 10 12 ions cm −2 , the output drain current and on/off current ratio ( I on / I off ) decrease by more than one order of magnitude, field‐effect mobility ( μ FE ) reduces more than four times, and subthreshold swing (SS) increases more than four times along with a negative shift in threshold voltage. The observed degradation is attributed to increased surface roughness and defect density, as confirmed by scanning electron microscopy (SEM), high‐resolution micro‐Raman, and transmission electron microscopy (TEM) with geometric phase analysis (GPA). A technique is demonstrated to recover the device performance at room temperature and in less than a minute, using the electron wind force (EWF) obtained from low‐duty‐cycle high‐density pulsed current. At a pulsed current density of 4.0 × 10 5 A cm −2 , approximately four times increase in I on / I off is observed, 41% increase in μ FE , and 20% decrease in the SS of the irradiated TFTs, suggesting effectiveness of the new annealing technique.

Al-Mamun, Nahid Sultan↗

DOE OSTI2021

Construction of Lattice Strain in Bimetallic Nanostructures and Its Effectiveness in Electrochemical Applications

Bimetallic nanocrystals (NCs), associated with various surface functions such as ligand effect, ensemble effect, and strain effect, exhibit superior electrocatalytic properties. The stress-induced surface strain effect can alter binding strength between the surface active sites and reactants as well as their intermediates, and the electrochemical performance of bimetallic NCs can be significantly facilitated by the lattice-strain modification via their morphologies, sizes, shell-thickness, surface defectiveness as well as compositions. Here in this review, an overview of fundamental principles, characterization techniques, and quantitative determination of the surface lattice strain is provided. Various strategies and synthesis efforts on creating lattice-strain-engineered bimetallic NCs, including the de-alloying process, atomic layer-by-layer deposition, thermal treatment evolution, one-pot synthesis, and other efforts are also discussed. It is further outlined how the lattice strain effect promotes electrochemical catalysis through the selected case studies. The reactions on oxygen reduction reaction, small molecular oxidation, water splitting reaction, and electrochemical carbon dioxide reduction reactions are focused. In particular, studies of lattice strain arisen from core–shell nanostructure and defectiveness are highlighted. Lastly, the potential challenges are summarized and the prospects of lattice-strain-based engineering on bimetallic nanocatalysts with suggestion and guidance of the future electrocatalyst design are envisioned.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Phase evolution in two-phase alloys during severe plastic deformation

Herein, phase evolution in FCC metals with strongly interacting alloy components during severe plastic deformation is investigated using molecular dynamics simulations. Specifically, we study the alloy microstructure in steady state, nucleation and growth of precipitates in supersaturated alloys, and the decomposition of precipitates in undersaturated alloys. The results are compared to a modified effective temperature model, providing a physical understanding for the atomic processes underlying the model and a perspective on its strengths and weaknesses. Key observations in this work are nucleation and growth of precipitates during SPD at a temperature of 100 K; Gibbs-Thomson-like behavior relating solubility to precipitate size under steady-state shearing; a direct relationship between the effective temperature and the shear modulus; and the importance of cluster agglomeration during precipitate growth. The study also reveals that the mechanisms of forced chemical mixing depends on precipitate size, adding complications for effective temperature models describing inhomogeneous systems. The simulations are shown to provide good semiquantitative agreement with experimental findings reported in the literature.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Design and performance analysis of a Swirl Pintle injector for a 1 MW th pressurized oxy-coal combustor

Pressurized Oxy-coal combustion has the potential to achieve high thermal efficiency by recovering the latent heat of steam from flue gases and providing options for up to 95% carbon capture. Here, this study proposes a novel burner technology for pressurized oxy-coal combustion and investigates its operability. Three burner versions are designed and tested; no swirl, swirl numbers 0.9 and 1.2 to identify optimum design parameters and performance. A commercially available Dantec Dynamics software is used to conduct the shadowgraph experiments to observe burner performance. Coal water slurry is used as fuel with three different slurry ratios where the coal percentage by weights were 30, 40 and 50. Droplet size, distribution, spray angle and jet breakup lengths are measured and analyzed to quantify the performance. The study found that increasing the swirl number enhanced atomization. Implementing swirlers allowed the jet to spread through faster primary jet separation, thus improving atomization. In addition, higher slurry ratios improved the generation of smaller particles. However, it was also found that excessive increases in oxidizer momentums negatively impact the atomization process by jet shrinkage. The study concluded that operating a pintle burner at 1.2 swirl conditions with a 40/60 slurry ratio produces optimum performance.

42 ENGINEERING↗

DOE OSTI2025

Surface engineering of polymeric membranes with metal oxides for improved fouling resistance and superior oil-water separation

Rapid industrial growth has increased the need for efficient membranes to separate oil-water emulsions. Polyvinylidene fluoride (PVDF) membranes, although widely used due to their chemical inertness and favorable mechanical properties, suffer from fouling due to their intrinsic hydrophobicity. Modifying these membranes after fabrication offers a practical solution as it easily fits into existing large-scale manufacturing processes. Atomic layer deposition (ALD), an atomically-precise vapor phase surface modification technique, can create ultrathin metal oxide layers that greatly improve membrane hydrophilicity without significantly affecting the original pore size. However, PVDF's lack of reactive chemical moieties makes ALD challenging. Here, in this study, we present a simple alkali treatment that greatly enhances ALD nucleation and growth on PVDF membranes. This treatment imparts exceptional oil-water emulsion separation capabilities and antifouling behavior in PVDF membranes after just a few ALD cycles, surpassing the performance of PVDF membranes coated with hundreds of ALD cycles. This dramatic reduction in the number of ALD cycles required could enable cost-effective modification of commercial PVDF membranes at scale using spatial, roll-to-roll ALD. These modified membranes outperform reported modified PVDF membranes, with >99 % permeance recovery and <1 % irreversible loss of permeance and >98 % oil rejection from oil-water emulsions over 100 h continuous operation, making them promising for advanced water purification technologies.

Atomic layer deposition↗

DOE OSTI2026

Identification of In Situ Generated High-Spin Fe(II)-N 4 Active Sites for Acidic Oxygen Reduction Reaction via Operando 57 Fe Mössbauer Spectroscopy

Iron-nitrogen-carbon (FeNC) catalysts are considered among the most promising alternative to Pt catalysts in acidic oxygen reduction reaction (ORR), yet the geometric and electronic structures of the true active site under reaction conditions have not been clearly elucidated. Herein, we synthesized a representative FeNC catalyst by pyrolyzing Fe 3+ absorbed on ZIF-8-derived N-doped carbon at a mild temperature under the H 2 /Ar atmosphere, where a formation mechanism of FeN 4 sites through a Zn-mediated Fe nanoparticle atomization process was proposed. The resulting FeNC-750 catalyst shows high acidic ORR activity with a half-wave potential of 0.838 V and a peak power density of 1 W cm -2 in proton-exchange membrane fuel cell (PEMFC). By using operando 57 Fe Mössbauer spectroscopy on FeNC-750, it was revealed that the pyrrolic N-coordinated high-spin Fe 2+ N 4 sites, which are in situ generated from high-spin Fe 3+ N 4 during ORR, are identified as catalytic active states. Density functional theory calculations further verified that, compared to the pyridinic N-coordinated low-spin Fe 2+ N 4 , the pyrrolic N-coordinated high-spin Fe 2+ exhibits optimized adsorption energy for reaction intermediates, thereby lowering the energy barrier of the rate-determining step (RDS) and facilitating OH* desorption. In conclusion, this work provides both experimental and theoretical evidence of the true active site in the FeNC during acidic ORR, offering significant insights for the rational design of high-performance materials for acidic fuel cells.

FeNC catalyst↗

DOE OSTI2024

Spatiotemporal dynamics of fast electron heating in solid-density matter via XFEL

Abstract High-intensity, short-pulse lasers are crucial for generating energetic electrons that produce high-energy-density (HED) states in matter, offering potential applications in igniting dense fusion fuels for fast ignition laser fusion. High-density targets heated by these electrons exhibit spatially non-uniform and highly transient conditions, which have been challenging to characterize due to limitations in diagnostics that provide simultaneous high spatial and temporal resolution. Here, we employ an X-ray Free Electron Laser (XFEL) to achieve spatiotemporally resolved measurements at sub-micron and femtosecond scales on a solid-density copper foil heated by laser-driven fast electrons. Our X-ray transmission imaging reveals the formation of a solid-density hot plasma localized to the laser spot size, surrounded by Fermi degenerate, warm dense matter within a picosecond, and the energy relaxation occurring within the hot plasma over tens of picoseconds. These results validate 2D particle-in-cell simulations incorporating atomic processes and provide insights into the energy transfer mechanisms beyond current simulation capabilities. This work significantly advances our understanding of rapid fast electron heating and energy relaxation in solid-density matter, serving as a key stepping stone towards efficient high-density plasma heating and furthering the fields of HED science and inertial fusion energy research using intense, short-pulse lasers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Cooperative mechanisms behind nanoscale smoothing on metal surfaces: From adatom diffusion to step nucleation

Many technologies require stable or metastable surface morphology. Here, in this paper we study the factors that control the metastability of a common feature of rough surfaces: “hillocks.” We use low energy electron microscopy to follow the evolution of the individual atomic steps in hillocks on Pd(111). We show that the uppermost island in the stack often adopts a static, metastable configuration. Modeling this result shows that the degree of the metastability depends on the configuration of steps dozens of atomic layers lower. Our model allows us to link surface metastability to the atomic processes of surface evolution.

Fernandes Cauduro, Andre Luis↗

DOE OSTI2024

Ultra-intense femtosecond laser interactions with aligned nanostructures

The interaction of ultrafast laser pulses of relativistic intensity with high aspect ratio nanostructures can efficiently and volumetrically heat matter to an ultra-high-energy-density regime encountered in the center of stars and within the core of fusion capsules compressed by the world’s largest lasers. It also generates gigantic quasi-static electromagnetic fields that accelerate particles to very high energy. Here, we present an overview of the physics and applications of these dense relativistic plasmas that can be created with pulses of relatively modest energy from lasers that can operate at a high repetition rate. Recent nanowire array experiments produced near-solid density plasmas with an extreme degree of ionization (e.g., Au +72 ), converted ultrafast pulses of laser light into intense x-ray flashes with record efficiency, and accelerated ions to MeV energies, efficiently driving micro-scale fusion reactions that generate flashes of quasi-monoenergetic neutrons. These plasmas also serve as a platform for advancing the understanding of atomic processes in extreme environments and open a new pathway to laser-driven fusion energy. The irradiation of nanostructures at intensities of > 1 x 10 22 W cm –2 is predicted to lead to an extreme ultra-high energy density plasma regime characterized by terabar pressures that is virtually unexplored.

Optics↗

DOE OSTI2024

Physics-assisted Latent Space Dynamics Learning for Stiff Collisional-radiative Models

Collisional-radiative (CR) models describe the atomic processes in a plasma by tracking the population density in the ground and excited states for each charge state of the atom/ion. These models predict important plasma properties such as charge state distributions and radiative emissivity and opacity. Accurate descriptions of the CR balance of the plasma are essential in fusion whole device modeling, especially when significant impurities are introduced into the plasmas. In an integrated fusion plasma and CR simulation, a CR model, which is a high-dimensional stiff ODE, needs to be solved on each grid point in the configuration space, and can overwhelm the overall computational cost. In this work, we propose a machine-learning-based method that discovers a latent space and learns its corresponding latent dynamics, which can capture the essential physics to make accurate predictions at much lower online computational cost. The proposed approach is physics-assisted, due to its combination of a physical latent space and a data-driven latent space. It has been demonstrated that the proposed architecture can predict both the full-order CR dynamics and a physical quantity of interest accurately.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Jump-Start U.S. Manufacturing of High-Performance Permanent Magnets

Gas atomized feedstock powders for Nd-Fe-B based magnets are more robust and cost effective than the strip-cast sheet currently used as feedstock for milling by the magnet industry. However, gas atomized powder’s crystallinity and grain boundary phases are less ideal than the strip cast flake. We proposed to optimize the atomization process as well as the powder chemistry to address this issue and to eliminate heavy rare earth elements from these magnet alloys. Our goal is to help GKN-Hoeganaes, a US metal powder company, who used to make Nd-Fe-B magnets, to bring back US manufacturing of these high energy density permanent magnets.

36 MATERIALS SCIENCE↗