Search NASA⌕ Search

SEARCH · Search NASA

Results for “axial”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Peak axial-velocity decay with multi-element rectangular and triangular nozzles

The aircraft noise created by the impingement of engine exhaust jet of STOL aircraft with externally blown flaps is discussed. It was determined that the jet-flap interaction noise can be lowered by reducing the impinging velocity of the jet. The reduction must occur at a specific distance from the flap to be effective. The peak axial-velocity decay obtained with rectangular and triangular single element mixer nozzles is presented. Equations are developed for estimating the peak axial velocity decay curves for a wide range of nozzle configurations.

Groesbeck, D. E.↗
NASA NTRS1972

Peak axial-velocity decay with single- and multi-element nozzles.

Jet peak-velocity decay data were obtained for a variety of circular and noncircular single-element and multi-element nozzles for application to externally-blown-flap STOL aircraft. These data permit a rational approach, in terms of element type and element spacing, to nozzles designed to promote mixing of the jet exhaust with the surrounding air. Rapid mixing and the resulting lower axial jet velocity decreases the noise caused by the interaction of jet impingement on the flap assembly of EBF STOL aircraft. Empirical relationships are presented that permit the prediction of peak axial-velocity decay curves for a wide spectrum of mixer-type nozzles. The data are useful also in the design of ejector-type noise suppressors and for the suppression of VTOL downwash velocities caused by vertically oriented exhaust nozzles.

Von Glahn, U. H.↗
NASA NTRS1973

Turbulent mixing of multiple, co-axial helium jets in a supersonic air stream

An experimental study of a strut-mounted, five-port, coaxial gaseous fuel injector assembly in a Mach 4 air stream with P sub o = 145 psia and T sub o = 546 R was conducted. Helium was used as the injectant, and the interjet spacing was the main parameter varied. The principal data are in the form of helium concentration profiles at six axial stations and pitot pressure profiles at two axial stations. Schlieren photographs are also presented. The slight sensitivity of the mixing rate to decreased interjet spacing was determined in the range 3.5 or = to S/D or = to 5.0.

Lorber, A. K.↗
NASA NTRS1973

FORTRAN program for calculating velocities and streamlines on the hub-shroud mid-channel flow surface of an axial- or mixed-flow turbomachine. 1: User's manual

A FORTRAN 4 computer program has been developed that obtains a subsonic or shock-free transonic flow solution on the hub-shroud mid-channel flow surface of a turbomachine. The blade row may be fixed or rotating, and may be twisted and leaned. Flow may be axial or mixed, up to 45 deg from axial. Upstream and downstream flow variables may vary from hub to shroud, and provision is made to correct for loss of stagnation pressure. The results include velocities, streamlines, and flow angles on the flow surface; and approximate blade surface velocities. Subsonic solutions are obtained by a finite-difference stream-function solution. Transonic solutions are obtained by a velocity-gradient method, using information from a finite-difference stream-function solution at a reduced mass flow.

Katsanis, T.↗
NASA NTRS1973

A cylindrical shell with an axial crack under skew-symmetric loading.

The skew-symmetric problem for a cylindrical shell containing an axial crack is considered. It is assumed that the material has a special orthotropy - namely, that the shear modulus may be evaluated from the measured Young's moduli and Poisson ratios and is not an independent material constant. The problem is solved within the confines of an eighth-order linearized shallow shell theory. As numerical examples, the torsion of an isotropic cylinder and that of a specially orthotropic cylinder (titanium) are considered. The membrane and bending components of the stress intensity factor are calculated and are given as functions of a dimensionless shell parameter. In the torsion problem for the axially cracked cylinder the bending effects appear to be much more significant than that found for the circumferentially cracked cylindrical shell. Also, as the shell parameter increases, unlike the results found in the pressurized shell, the bending stresses around crack ends do not change sign.

Yuceoglu, U.↗
NASA NTRS1974

Data summary and computer program for axial-flow pump rotor performance

Assembly of noncavitating blade element performance data for axial-flow pump rotor configurations has been collected and organized. Program facilitates handling large amounts of experimental data involved and may be used as data reduction program to process flow and performance measurements from other axial-flow pump configurations.

Miller, M. J.↗
NASA NTRS1974

Computer program for definition of transonic axial-flow compressor blade rows

A method is presented for designing axial-flow compressor blading from blade elements defined on cones which pass through the blade-edge streamline locations. Each blade-element centerline is composed of two segments which are tangent to each other. The centerline and surfaces of each segment have constant change of angle with path distance. The stacking line for the blade elements can be leaned in both the axial and tangential directions. The output of the computer program gives coordinates for fabrication and properties for aeroelastic analysis for planar blade sections. These coordinates and properties are obtained by interpolation across conical blade elements. The program is structured to be coupled with an aerodynamic design program.

Crouse, J. E.↗
NASA NTRS1974

FORTRAN program for calculating velocities and streamlines on the hub-shroud mid-channel flow surface of an axial-or mixed-flow turbomachine. 2: Programmer's manual

A FORTRAN-IV computer program, MERIDL, has been developed that obtains a subsonic or shock-free transonic flow solution on the hub-shroud mid-channel flow surface of a turbomachine. The blade row may be fixed or rotating and may be twisted and leaned. Flow may be axial or mixed, up to 45 deg from axial. Upstream and downstream flow variables can vary from hub to shroud, and provision is made to correct for loss of stagnation pressure. The results include velocities, streamlines, and flow angles on the flow surface and approximate blade surface velocities. Subsonic solutions are obtained by a finite-difference stream-function solution. Transonic solutions are obtained by a velocity-gradient method, using information from a finite-difference stream-function solution at a reduced mass flow.

Katsanis, T.↗
NASA NTRS1974

Shock-induced separation of adiabatic turbulent boundary layers in supersonic axially symmetric internal flow

An experimental investigation at Mach 4 of shock-induced turbulent boundary layer separation at the walls of axially symmetric flow passages is discussed, with particular emphasis placed on determining the shock strengths required for incipient separation. The shock waves were produced by interchangeable sting-mounted cones placed on the axes of the flow passages and aligned with the freestream flow. The interactions under study simulate those encountered in axially symmetric engine inlets of supersonic aircraft. Knowledges of the shock strengths required for boundary layer separation in inlets is important since for shocks of somewhat greater strength rather drastic alterations in the inlet flow field may occur.

Page, R. J.↗
NASA NTRS1974

Axial flow measurements in trailing vortices

A scanning laser Doppler velocimeter was used to measure the axial velocity defect in the cores of trailing vortices behind a lifting airfoil of rectangular planform. Data were obtained at several different angles of attack and downstream distances ranging from 30 to 1000 chord lengths. The test was designed to obtain continuous data from the near field into the far field while removing uncertainties associated with the interpretation of data obtained by the hydrogen bubble technique. The measured velocities of V sub x/U sub infinity are compared with those predicted. The agreement is remarkably good over the entire range of downstream distances, which supports the credibility of calculating axial velocities using the results of Moore and Saffman (1973).

Ciffone, D. L.↗
NASA NTRS1975

Effect on fan flow characteristics of length and axial location of a cascade thrust reverser

A series of static tests were conducted on a model fan with a diameter of 14.0 cm to determine the fan operating characteristics, the inlet static pressure contours, the fan-exit total and static pressure contours, and the fan-exit pressure distortion parameters associated with the installation of a partial-circumferential-emission cascade thrust reverser. The tests variables included the cascade axial length, the axial location of the reverser, and the type of fan inlet. It was shown that significant total and static pressure distortions were produced in the fan aft duct, and that some configurations induced a static pressure distortion at the fan face. The amount of flow passed by the fan and the level of the flow distortions were dependent upon all the variables tested.

Dietrich, D. A.↗
NASA NTRS1974

Turbulent mixing of multiple co-axial gaseous fuel jets in a supersonic airstream

An experimental and analytical investigation of a strut-mounted, four-nozzle, downstream-facing, gaseous fuel-injector assembly was conducted in a Mach 4 airstream at 154 psia and 520 R. Helium was used as the injectant in order to simulate a low molecular weight fuel, and the interjet spacing (S/D) was the main parameter varied. The principal data are in the form of helium concentration profiles at seven axial stations, Mach number distributions at three axial stations, and Schlieren photographs of the flow field at different interjet spacings. An approximate analysis was developed based upon a linearization in the Von Mises plane, Crocco integrals for the temperature and concentrations fields, and an eddy viscosity model. Good agreement with the data was achieved. It was found that, at these conditions, interjet spacing has a significant effect on mixing only up to S/D of approximately 2.5, with the concentration of the injectant at a given point becoming smaller as S/D is increased.

Lorber, A. K.↗
NASA NTRS1976

Thermal Analysis of Axially Grooved Heat Pipes

The liquid viscous drag and the evaporator film coefficient were determined analytically for a heat pipe with axial rectangular grooves under zero-g conditions. The liquid pressure drop and the evaporator film coefficient for an axially grooved heat pipe were found to be expressed by the functions of the meniscus angle, which makes it possible to predict its performance analytically. The performance near its capillary pumping limit is influenced by the contact angle.

Kamotani, Y.↗
NASA NTRS1975

Effects of casing treatment on a small, transonic axial-flow compressor

Improved axial compressor surge margin through effective rotor casing treatment has been identified from test results on large axial compressors. A modified scale of a large compressor was built and tested to determine if similar improvements in surge margin could be duplicated in small-size turbomachinery. In addition, the effects of rotor radial running clearance, both with and without casing treatment, were investigated and are discussed. Test results of the scale configuration are presented and compared to the parent compressor.

Holman, F. F.↗
NASA NTRS1976

Computation of the inviscid supersonic flow over an external axial corner

A second-order finite-difference procedure is used to evaluate the inviscid supersonic flowfield surrounding an external axial corner composed of swept planar compression surfaces and representing the inlets on existing high-speed aircraft. The governing partial differential equations in conservation-law form are hyperbolic with respect to the axial coordinate and are solved iteratively by means of MacCormack's algorithm. The procedure treats both the peripheral shock wave and vortical singularities as discontinuities. Numerical results are presented for two parametric studies regarding the effects on the flowfield of varying the free-stream Mach number and the leading edge sweep of the horizontal wedge. Results of parametric Mach number study agree with the Mach number independence principle in that as the Mach number increases, such characteristics as shock shape, cross-flow sonic line location, and vortical singularity position approach an asymptote.

Kutler, P.↗
NASA NTRS1976

Investigation of performance limits in axial groove heat pipes

The entrainment-shear performance limit which occurs in axial groove heat pipes was investigated and explained. In the existing heat pipe literature the entrainment heat flux limit is defined as the condition where the Weber number is greater than or equal to one. In this analysis, the critical value for the entrainment Weber number is found to be 2 pi less than or equal to 3 pi. Perhaps more important to the heat pipe designer than the entrainment performance limit is the prediction of the performance degradation due to vapor-liquid shearing stress which is also described. Preliminary qualitative experiments were conducted to observe the shear. stress wave formation phenomena. The equations presented may be used to predict and minimize the vapor-liquid shear stress performance effects that occur in axial groove and puddle flow artery heat pipes.

Feldman, K. T.↗
NASA NTRS1976

Deformations of thick two-material cylinder under axially varying radial pressure

Stresses and deformations in thick, short, composite cylinder subjected to axially varying radial pressure are studied. Effect of slippage at the interface is examined. In the NASTRAN finite element model, multipoint constraint feature is utilized. Results are compared with theoretical analysis and SAP-IV computer code. Results from NASTRAN computer code are in good agreement with the analytical solutions. Results suggest a considerable influence of interfacial slippage on the axial bending stresses in the cylinder.

Patel, Y. A.↗
NASA NTRS1977

Axially grooved heat pipes - 1976

This paper summarizes the 'state-of-the-art' of axially grooved heat pipes. Applications are identified and the related heat pipe design and performance are defined. Recent developments in the analysis, design and fabrication of axially grooved hardware are also discussed. A mathematical model which predicts the hydrodynamic behavior and accounts for liquid recession, liquid/vapor shear interaction and 1-g puddle flow is also presented. Performance data for various fluids in the 100-500 K range is compared to predictions from the Groove Analysis Program (GAP). Finally, a simplified closed form solution which accounts for gravity effects, self-priming and composite pumping by the grooves as well as all of the hydrodynamic losses is also discussed.

Brennan, P. J.↗