Search NASA⌕ Search

SEARCH · Search NASA

Results for “axial roots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Mixing of Multiple Jets with a Confined Subsonic Crossflow in a Cylindrical Duct

This paper summarizes NASA-supported experimental and computational results on the mixing of a row of jets with a confined subsonic crossflow in a cylindrical duct. The studies from which these results were derived investigated flow and geometric variations typical of the complex 3-D flowfield in the combustion chambers in gas turbine engines. The principal observations were that the momentum-flux ratio and the number of orifices were significant variables. Jet penetration was critical, and jet penetration decreased as either the number of orifices increased or the momentum-flux ratio decreased. It also appeared that jet penetration remained similar with variations in orifice size, shape, spacing, and momentum-flux ratio when the number of orifices was proportional to the square-root of the momentum-flux ratio. In the cylindrical geometry, planar variances are very sensitive to events in the near wall region, so planar averages must be considered in context with the distributions. The mass-flow ratios and orifices investigated were often very large (mass-flow ratio greater than 1 and ratio of orifice area-to-mainstream cross-sectional area up to 0.5), and the axial planes of interest were sometimes near the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. The results shown also seem to indicate that non-reacting dimensionless scalar profiles can emulate the reacting flow equivalence ratio distribution reasonably well. The results cited suggest that further study may not necessarily lead to a universal 'rule of thumb' for mixer design for lowest emissions, because optimization will likely require an assessment for a specific application.

Holdeman, James D.↗
NASA NTRS1999

Investigation of Point Doppler Velocimetry (PDV) for Transition Detection in Boundary Layers

A two-component Point Doppler Velocimeter (PDV) system has been improved through the use of vapor-limited iodine cells that have responses that are insensitive to temperature variations. Two-component PDV velocity measurements have been obtained for a 1 inch diameter uniform circular jet flow at a nominal exit velocity of 60 m/sec, corresponding to a Reynolds number of 100,000. Similar data have also been obtained for an annular jet and a swirling jet, These PDV data runs have been duplicated to judge the repeatability of these measurements, and also have been compared with hot wire anemometer data for the same flow conditions. PDV mean velocity results are repeatable to within approximately 1-2 meters per second; the PDV RMS velocity results are also quite repeatable. Exit profiles of PDV mean axial velocity data generally agree with hot wire anemometer results to within about 2 meters per second as well. However, the PDV RMS velocity results are consistently lower than the hot wire results everywhere but at the exit of the standard jet, where they are too high relative to the hot wire data. This is believed to at least be partially due to the method used to compute the RMS (Root Mean Square).

Kuhlman, John↗
NASA NTRS1974

A movable-mass attitude stabilization system for cable-connected artificial-g space stations

The development of an active, momentum-exchange system to be used for attitude stabilization of a class of cable-connected artificial-g space stations is studied. A system which employs a single movable control mass is examined for the control of a space station which has the physical appearance of two cylinders connected axially by cables. The dynamic model for the space station includes its aggregate rigid body rotation and relative torsional rotation between the bodies. A zero torsional stiffness design (one cable) and a maximum torsional stiffness design (eight cables) are examined in various stages of deployment, for selected spin velocities ranging from 4 rpm upwards. A linear, time-invariant, feed-back control system is employed, with gains calculated via a root-specification procedure. The movable mass controller provides critical wobble-damping capability for the crew quarters for all configurations and spin velocity.

Childs, D. W.↗
DOE OSTI2021

A Flow Rate Dependent 1D Model for Thermally Stratified Hot-Water Energy Storage

Stratified tank models are used to simulate thermal storage in applications such as residential or commercial hot-water storage tanks, chilled-water storage tanks, and solar thermal systems. The energy efficiency of these applications relates to the system components and the level of stratification maintained during various flow events in the tank. One-dimensional (1D) models are used in building energy simulations because of the short computation time but often do not include flow-rate dependent mixing. The accuracy of 1D models for plug flow, plug flow with axial conduction, and two convection eddy-diffusivity models were compared with experimental data sets for discharging a 50-gal residential tank and recharging the tank with hot water from an external hot-water source. A minimum and maximum relationship for the eddy diffusivity factor were found at Re <2100 and >10,000 for recirculation of hot water to the top of the tank and vertical tubes inletting cold water at the bottom. The root mean square error decreased from >4 °C to near 2 °C when considering flow-based mixing models during heating, while the exponential decay of the eddy diffusion results in a root mean square error reduction of 1 °C for cone-shaped diffusers that begin to relaminarize flow at the inlet.

1D flow model↗
NASA NTRS1997

On-Orbit and Ground Performance of the PGBA Plant Growth Facility

PGBA, a plant growth facility developed for commercial space biotechnology research, successfully grew a total of 30 plants (6 species) for 10 days on board the Space Shuttle Endeavour (STS-77) and is scheduled for reflight on board MSL-1 (STS-83) for a 16 day flight. The PGBA life support systems provide atmospheric, thermal, and humidity control as well as lighting and nutrient supply in a 23.6 liter chamber. Atmosphere treatment includes ethylene and other hydrocarbon removal, CO2 replenishment, and O2 control. The normally closed system uses controlled CO2 replenishment from the crew cabin as required by the plants. Temperature is controlled (1 C) at user-specified setpoints between 20-32 C, using water-filled coolant loops, solid state Peltier thermoelectric devices, and liquid heat exchangers. The thermoelectric cooling systems were optimized for low power consumption and high cooling efficiencies. Relative humidity is maintained between 60-100% using a cooled porous metal plate to remove water vapor from the air stream without cooling the bulk air below the dew point. The lighting system utilizes three compact fluorescent bi-axial lights with variable lighting control and light intensity (PAR) between 220 and 330 micromol/sq m/s at a distance of 20 cm in spaceflight configuration (on orbit power limited to 230 Watt for entire payload). A ground, up to 550 micromol/sq m/s light intensity can be achieved with 330 Watt payload power consumption. Plant water and nutrient support is sustained via the 'Nutrient Pack' system including the passive or active 'Water Replenishable Nutrient Pack.' The root matrix material (soil or Agar) and nutrient formulation of each pack is prepared according to plant species and experimental requirements. These systems were designed by NASA Ames personnel. Data acquisition and control systems provide 32 channels of environmental data as well as digitized or analog video signals for downlink.

Hoehn, A.↗
NASA NTRS1981

The influence of gyroscopic forces on the dynamic behavior of rotating blades

The question of divergent oscillatory stability of an axial turbomachine blade when the bladed rotor system is subjected to a forced precessional motion is studied by using two simplified models of the blade. The simplest (lumped) model is a point mass restrained by three orthogonal linear springs attached to the rotor. An improved distributed parameter model represents the blade by a uniform cantilever beam with bending in one plane. In both instances instability is shown to be strongly dependent upon the ratio of blade root radius to blade length and the magnitude of the rotor spin relative to the nonrotating blade natural frequency for realistic values of precession rate. Results are presented on augmented Campbell diagrams. Implications for design and operation are drawn as are the characteristics of needed future studies.

Sisto, F.↗
NASA NTRS1988

Current-driven resistive ballooning modes in axially bounded solar flare plasmas

The most unstable current-driven resistive modes of an axially bounded coronal loop are found in computer simulations to exhibit the spatial structure of ballooning modes. The observed modes are not confined to mode rational surfaces, but instead have broad radial extent. A theory assuming ballooning mode spatial structure predicts that a minimum current should be required for linear instability, and that, when the mode is unstable, the linear growth rate scales linearly with the resistivity eta below a critical resistivity, and scales as cu root of eta for larger resistivities. Both predictions are borne out by simulation results. Both theory and simulation analyses of the mode suggest that the strong radial structure of the mode near the ends of the system is the primary contributing factor to the instability of the mode. A helical current sheet is formed in the nonlinear evolution of the mode near the edge of the current channel and is accompanied by a strong radial gradient in the current and partial current reversal.

Otani, Niels F.↗
DOE OSTI2024

Neural network emulation of spontaneous fission

Large-scale computations of fission properties are an important ingredient for nuclear reaction network calculations simulating rapid neutron-capture process (the 𝑟 process) nucleosynthesis. Due to the large number of fissioning nuclei potentially contributing to the 𝑟 process, a microscopic description of fission based on nuclear density functional theory (DFT) is computationally challenging. Here, we explore the use of neural networks (NNs) to construct DFT emulators capable of predicting potential energy surfaces and collective inertia tensors across the whole nuclear chart, starting from a minimal set of DFT calculations. We use constrained Hartree-Fock-Bogoliubov (HFB) calculations to predict the potential energy and collective inertia tensor in the axial quadrupole and octupole collective coordinates, for a set of nuclei in the 𝑟-process region. We then employ NNs to emulate the HFB energy and collective inertia tensor across the considered region of the nuclear chart. Least-action pathways characterizing spontaneous fission half-lives and fragment yields are then obtained by means of the nudged elastic band method. The potential energy predicted by NNs agrees with the DFT value to within a root-mean-square error of 500 keV, and the collective inertia components agree to within an order of magnitude. These results are largely independent of the NN architecture. The exit points on the outer turning line are found to be well emulated. For the spontaneous fission half-lives the NN emulation provides values that are found to agree with the DFT predictions within a factor of 10 3 across more than 70 orders of magnitude. Neural networks are able to emulate the potential energy and collective inertia well enough to reasonably predict physical observables. Future directions of study, such as the inclusion of additional collective degrees of freedom and active learning, will improve the predictive power of microscopic theory and further enable large-scale fission studies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2006

3D Relativistic Magnetohydrodynamic Simulations of Magnetized Spine-Sheath Relativistic Jets

Numerical simulations of weakly magnetized and strongly magnetized relativistic jets embedded in a weakly magnetized and strongly magnetized stationary or weakly relativistic (v = c/2) sheath have been performed. A magnetic field parallel to the flow is used in these simulations performed by the new GRMHD numerical code RAISHIN used in its RMHD configuration. In the numerical simulations the Lorentz factor gamma = 2.5 jet is precessed to break the initial equilibrium configuration. In the simulations sound speeds are less than or equal to c/the square root of 3 in the weakly magnetized simulations and less than or equal to 0.56 c in the strongly magnetized simulations. The Alfven wave speed is less than or equal to 0.07 c in the weakly magnetized simulations and less than or equal to 0.56 c in the strongly magnetized simulations. The results of the numerical simulations are compared to theoretical predictions from a normal mode analysis of the linearized relativistic magnetohydrodynamic (RMHD) equations capable of describing a uniform axially magnetized cylindrical relativistic jet embedded in a uniform axially magnetized relativistically moving sheath. The theoretical dispersion relation allows investigation of effects associated with maximum possible sound speeds, Alfven wave speeds near light speed and relativistic sheath speeds. The prediction of increased stability of the weakly magnetized system resulting from c/2 sheath speeds and the stabilization of the strongly magnetized system resulting from c/2 sheath speeds is verified by the numerical simulation results.

Mizuno, Yosuke↗
NASA NTRS2004

Aligning Arrays of Lenses and Single-Mode Optical Fibers

A procedure now under development is intended to enable the precise alignment of sheet arrays of microscopic lenses with the end faces of a coherent bundle of as many as 1,000 single-mode optical fibers packed closely in a regular array (see Figure 1). In the original application that prompted this development, the precise assembly of lenses and optical fibers serves as a single-mode spatial filter for a visible-light nulling interferometer. The precision of alignment must be sufficient to limit any remaining wavefront error to a root-mean-square value of less than 1/10 of a wavelength of light. This wavefront-error limit translates to requirements to (1) ensure uniformity of both the lens and fiber arrays, (2) ensure that the lateral distance from the central axis of each lens and the corresponding optical fiber is no more than a fraction of a micron, (3) angularly align the lens-sheet planes and the fiber-bundle end faces to within a few arc seconds, and (4) axially align the lenses and the fiber-bundle end faces to within tens of microns of the focal distance. Figure 2 depicts the apparatus used in the alignment procedure. The beam of light from a Zygo (or equivalent) interferometer is first compressed by a ratio of 20:1 so that upon its return to the interferometer, the beam will be magnified enough to enable measurement of wavefront quality. The apparatus includes relay lenses that enable imaging of the arrays of microscopic lenses in a charge-coupled-device (CCD) camera that is part of the interferometer. One of the arrays of microscopic lenses is mounted on a 6-axis stage, in proximity to the front face of the bundle of optical fibers. The bundle is mounted on a separate stage. A mirror is attached to the back face of the bundle of optical fibers for retroreflection of light. When a microscopic lens and a fiber are aligned with each other, the affected portion of the light is reflected back by the mirror, recollimated by the microscopic lens, transmitted through the relay lenses and the beam compressor/expander, then split so that half goes to a detector and half to the interferometer. The output of the detector is used as a feedback control signal for the six-axis stage to effect alignment.

Liu, Duncan↗
NASA NTRS1983

Sound diffraction at wall impedance discontinuities in a circular cylinder, investigated using Wiener-Hopf technique

Rigorous solutions are presented for sound diffraction in a circular cylinder with axial discontinuities of the wall admittance (or impedance). Analytical expressions are derived for the reflection and the transmission coefficients for duct modes. The results are discussed quantitatively in the limits of small admittance shifts (delta) and of low frequencies (ka). One of the results is the low frequency behavior of the reflection coefficient R(o) sub 00 of the fundamental mode. For the mode of a hardwall duct reflected from the junction with a softwall duct, (R(o) sub oo yields - (1-square root of (ka) square root of (2/i delta)); this result is in contrast to the frequency dependence of the reflection from the open end of a hardwall duct, for which R(o) sub oo yields - 1-(ka) squared/2 .

Cho, Y. C.↗
NASA NTRS1983

Vibration characteristics of a deployable controllable-geometry truss boom

An analytical study was made to evaluate changes in the fundamental frequency of a two dimensional cantilevered truss boom at various stages of deployment. The truss could be axially deployed or retracted and undergo a variety of controlled geometry changes by shortening or lengthening the telescoping diagonal members in each bay. Both untapered and tapered versions of the truss boom were modeled and analyzed by using the finite element method. Large reductions in fundamental frequency occurred for both the untapered and tapered trusses when they were uniformly retracted or maneuvered laterally from their fully deployed position. These frequency reductions can be minimized, however, if truss geometries are selected which maintain cantilever root stiffness during truss maneuvers.

Dorsey, J. T.↗
NASA NTRS2000

Full Field Scalar Measurements in a Pulsating Helium Jet using Rainbow Schlieren Deflectometry

The flow structure of a pulsating helium jet was investigated using quantitative rainbow schlieren deflectometry. The operating parameters included the tube inside diameter, the jet Reynolds number and the jet Richardson number. The jet structure was characterized by the frequency spectrum, temporal evolution of the oscillations and mean and root-mean-square profiles of the species mole fraction, which in this case, was helium. Experiments were conducted using a variable nozzle facility. Angular deflection data were obtained using rainbow schlieren deflectometry across full field of color images taken at a temporal resolution of 60Hz. The flicker cycle was analyzed by instantaneous rainbow schlieren images, contour plots of deflection angle and helium mole fraction placed sequentially in time. Two observe the flow downstream, the tube was lowered with respect to the optical setup and images were taken at different axial planes. In this way, the laminar, transition and turbulent regions of the jet flow were observed. Abel inversion algorithm was utilized to reconstruct the refractive index field from the measurements of the beam deflection angle. The concentration field was then generated from the refractive index field. The phenomenon of vortex initiation and propagation in the flicker cycle was described by correlating the ray deflection angle and concentration contour plots. Experiments in the flickering jet reveal global oscillation in the flow field. The effect of jet exit Reynolds number and jet Richardson number on the flickering frequency was analyzed. The effect of jet Richardson number was more pronounced than that of the jet exit Reynolds number. The flow field was studies quantitatively in terms of temporal evolution and statistical description of helium mole fraction.

Pasumarthi, Kasyap S.↗
NASA NTRS1984

Inlet boundary layer effects in an axial compressor rotor. I - Blade-to-blade effects

This paper discusses experimental data measured on the blading and downstream of an isolated compressor rotor with thick inlet endwall boundary layers. The objective of the study was to compare these results with data acquired previously with thin inlet boundary layers and to assess the impact of inlet boundary layer thickness on the secondary flow. Flow visualization results showed the powerful impact of the hub corner stall and how at the same near stall flow coefficient where with thin inlet boundary layers the blade was separated at midspan, with thick inlet boundary layers it was attached. It was also shown that while secondary flow was very weak, it did produce sufficient radial redistribution to cause an apparent negative loss at the blade root.

Wagner, J. H.↗
NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗
DOE OSTI2023

Skyrme–Hartree–Fock–Bogoliubov mass models on a 3D mesh: IIb. Fission properties of BSkG2

Large-scale models of nuclear structure are currently the only way to provide consistent datasets for the many properties of thousands of exotic nuclei that are required by nucleosynthesis simulations. In [W. Ryssens et al., Eur. Phys. J. A 58, 246 (2022)], we recently presented the new BSkG2 model based on an energy density functional of the Skyrme type. Relying on a flexible three-dimensional coordinate representation of the nucleus, the model takes into account both triaxial deformation and time-reversal symmetry breaking. BSkG2 achieves a state-of-the-art global description of nuclear ground state (g.s.) properties and reproduces in particular the known masses with a root-mean-square (rms) deviation of 678 keV. Moving beyond g.s. properties, the model also reproduces all empirical values for the primary and secondary barriers as well as isomer excitation energies of actinide nuclei with rms deviations below 500 keV, i.e. with unprecedented accuracy. Here we discuss in detail the extension of our framework to the calculation of the fission barriers of 45 actinide nuclei, including odd-mass and odd-odd systems. We focus in particular on the impact of symmetry breaking which is key to the accuracy of the model: we allow systematically for axial, reflection and time-reversal symmetry breaking. The effect of the latter on the fission properties of odd-mass and odd-odd nuclei is small, but we find that allowing for shapes with triaxial or octupole deformation, as well as shapes with both, is crucial to achieving this accuracy. Here, the numerical accuracy of our coordinate space approach, the variety of nuclear configurations explored and the simultaneous successful description of fission properties and known masses makes BSkG2 the tool of choice for the large-scale study of nuclear structure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Blunt Impact Brain Injury using Cellular Injury Criterion

The Advanced Combat Helmet (\ACH") military specification (\mil-spec") requires a helmeted magnesium (\Mg") Department of Transportation (\DOT") headform be dropped vertically, with an impact speed of 3.1 m/s (10 ft/s), onto a steel hemispherical target. The pass/fail criteria are based on translational acceleration (150 G) alone, absent of any rotational component. Without a rotational component, the specification's injury risk application is limited to skull fracture and peripheral hematomas (subdural, subarachnoid), since this translational acceleration injury risk assessment is based on the Wayne State Tolerance Curve (\WSTC"). To provide a more comprehensive view of injury for the entire brain, an alternative approach is needed. To meet this need, we worked with a larger group called PANTHER, a collaboration between national laboratories, industry, and academia. Collaborations specific to research and results presented here come from efforts led by Mr. Ron Szalkowski and Mr. Sushant Malave, Ms. Alice Fawzi, and Dr. Christian Franck. We have developed a prototypical injury risk criterion based on the neuronal response to abrupt changes in general motion (translation, rotation, or both). The cellular-based mild traumatic brain injury (\cbmTBI") criterion utilizes both the strain and strain rate of brain tissue to account for the stretch and rate of stretch that occurs throughout the brain as a result of blunt impact to the head. We conducted physical experiments of an ACH-fitted magnesium headform, which produced repeatable headform peak accelerations. Then, we developed a simulation of the experiment, and validated the simulation output with the experimental data. We then substituted the magnesium headform with a human headform, consisting of skin, muscle, bone, gray matter, white matter, cerebral-spinal fluid, membranes, vasculature, intravertebral discs, airway and sinus. We quantified brain injury risk using the cbmTBI criterion, using the current mil-spec test and a modified test. The modified mil-spec test used an inclined anvil target that was located posterior to the crown of the helmet in the axial plane. While the current mil-spec test produced brain deformation from head translation alone, the modified test produced brain deformation from head translation and rotation, which is closer to most real world and combat theater impacts (e.g., such as occur in tertiary blast exposure). Compared to the current mil-spec test, the modified test produced elevated strains in the human digital twin. These data, mapped to the cbmTBI criterion, suggest increased injury risk for blunt impacts that cause rotation and translation, rather than just translation alone. Moreover, these data may lead to a rotational performance metric, which is rooted in the biology and pathology of the brain's response to impact and blast, and which should be used to improve next-generation helmet designs.

42 ENGINEERING↗
NASA NTRS1992

Investigation of rotor blade roughness effects on turbine performance

The cold air test program was completed on the SSME (Space Shuttle Main Engine) HPFTP (High Pressure Fuel Turbopump) turbine with production nozzle vane rings and polished coated rotor blades with a smooth surface finish of 30 microinch (0.76 micrometer) RMS (Root Mean Square). The smooth blades were polished by an abrasive flow machining process. The test results were compared with the air test results from production rough coated rotor blades with a surface finish of up to 400 microinch (10.16 micrometer) RMS. Turbine efficiency was higher for the smooth blades over the entire range tested. Efficiency increased 2.1 percentage points at the SSME 104 percent RPL (Rated Power Level) condition. This efficiency improvement could reduce the SSME HPFTP turbine inlet temperature by 57 degrees Rankine (32 degrees Kelvin) increasing turbine durability. The turbine flow parameter increased and the mid-span outlet swirl angle became more axial with the smooth rotor blades.

Boynton, J. L.↗