Search NASA⌕ Search

SEARCH · Search NASA

Results for “combustion chambers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Persistent Elevated Soot Emissions Induced by Clustered Stochastic Preignition Events

Stochastic Preignition (SPI) is an abnormal combustion phenomenon that can occur in spark-ignition engines particularly under high-load operation. SPI is characterized by uncontrolled initiation of combustion prior to spark discharge, an abnormal combustion process that can lead to severe knock events and significant engine damage. SPI has been associated with fuel properties, lubricant composition, and engine design and operation. Here, in this work, a single-cylinder test engine with a dry-sump oil system was utilized to study the SPI response of E10 and E25 fuels with a range of Reid Vapor Pressure (RVP). An automated test procedure was employed, consisting of ten square-waved load profile segments, with each segment composed of 5 min of low-load operation followed by 25 min of sustained high-load operation. These tests were replicated across multiple days of testing including a lubricant triple flush between tests, and an online Fuel in Oil diagnostic measurement. Exhaust particulate emissions were continuously measured by an AVL microsoot sensor (MSS). Elevated particulate matter emissions were observed to occur concurrently with SPI events as blooms of soot. Particularly after clustered events (i.e., multiple SPI cycles occurring within 10 consecutive engine cycles), high soot emissions were observed to persist over several days of sequential operation despite daily lubricant changes, a complete warm-up procedure, and sustained low-load operation between test segments. This result implies that the particulate emissions trends may be dominated by deposit-based effects, where higher load operation is needed to alter deposition and formation processes. The observed soot blooms were also found to correspond to a reduction in the engine fueling and the fuel engine oil dilution rate despite the engine exhaust remaining at stoichiometric exhaust operation. These observations suggest that post-SPI events, pathways for lubricant migration and consumption into the combustion chamber may occur until these pathways are closed from deposit formation or ring dynamics during extended operation. These observed sooting propensity persisted with all fuels tests, but a linear correlation was observed between the summation of soot and particulate matter index (PMI) value for each fuel as well as SPI events, proving that PMI is a crucial fuel property for reducing SPI.

Splitter, Derek [Oak Ridge National Laboratory (OR↗
DOE OSTI2020

THE EFFECT OF FUEL REACTIVITY AND EXHAUST GAS RECIRCULATION ON KNOCK PROPENSITY OF NATURAL GAS

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high compression ratio/elevated boost pressures and misfire at lean conditions/high exhaust gas recirculation (EGR) levels. The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine was used to characterize the effects of EGR and variation in natural gas fuel reactivity on the homogeneous ignition delay, flame propagation rate, and end- gas autoignition propensity for stoichiometric natural gas/oxidizer/EGR blends. A reduced chemical kinetic mechanism was also developed to accurately model the homogeneous ignition delays measured in the Colorado State University rapid compression machine (CSU RCM). Pipeline quality natural gas with a range of chemical reactivity (68 < Methane Number < 95) was simulated using mixtures of CH4, C2H6, and C3H8. Exhaust gas recirculation gases were simulated with mixtures of Ar, CO2, CO, and NO at substitution rates of 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 30.2 to 34.0 bar and compressed temperatures of 667 to 980 K. End-gas autoignition fraction and flame propagation rate were measured by initiating a laser spark in the center of the combustion chamber, after compression, at pressures of 30.7 to 32.7 bar and temperatures of 751 to 795 K. The results indicate that both fuel reactivity and the presence of reactive species (NO and CO) in the exhaust gas recirculation have a strong impact on end-gas autoignition fraction. A chemical kinetic mechanism was developed to predict homogeneous ignition delays for pipeline quality natural gas in a pressure and temperature range of 1-100 bar and 500-1000 K respectively. This mechanism accurately predicted measured homogeneous ignition delay in the RCM with a total average relative error of 11.0%.

Mohr, Jeffrey↗
DOE OSTI2022

Numerical Study on the Effect of Methane Doping in Hydrogen-Air Rotating Detonation Engines for Various Temperatures and Pressures

Rotating detonation engines (RDEs) have gained attention as a promising technology for future aviation engines. However, the numerical studies of these systems pose severe challenges due to the broad range of spatial and temporal scales. In this study, we use an adaptive mesh refinement based compressible, reactive solver PeleC to resolve the broad range of scales and accurately capture shock and detonation waves using high-resolution numerical schemes. Multi- species transport along with compressible Navier-Stokes equations are solved in the model along with a finite-rate based chemistry model. Embedded boundary method is used to model the complex geometry consisting of discrete fuel nozzles and the combustion chamber. The fuel consisting predominantly of hydrogen is doped with varying levels of methane while air is used as the oxidizer. For a specified total pressure and temperature, the number of stable detonation waves is found to decrease with increasing methane concentration in the fuel mixture. Additionally, no stable detonation solutions are observed for methane composition higher than 20% by volume for the range of operating conditions studied (300-900K, 10 Atm). The increased presence of high temperature zones is also indicative of higher thermal NOx emissions at low methane concentrations. The effect of fuel-air mixture composition and temperature on the detonability, detonation wave structure, mode transitions and their stability are analyzed in this study in addition to their implication on NOx emission.

automatic mesh refinement↗
DOE OSTI2022

System and method for engine control with pressure reactive device to control combustion timing

The present disclosure relates to a system for controlling ignition of an intake charge directed into an internal combustion engine. The system may have a movable component operably associated with at least one of a piston of the engine or a combustion chamber of the engine. The movable component may be tuned to deflect in response to a predetermined pressure being reached in a cylinder in which the piston is housed. The movable component operates to deflect in response to the predetermined pressure being reached in the cylinder as the piston travels toward top dead center during its compression stroke, to change a compression ratio of the engine.

Killingsworth, Nicholas↗
DOE OSTI2022

Air-fuel micromix injector having multibank ports for adaptive cooling of high temperature combustor

A method of using a combustor for high temperature combustion. The combustor is equipped with a showerhead type micromix air-fuel injector. The injector faceplate has its ports concentrically arranged into “banks”, to which delivery of fuel can be controlled on a bank-by-bank basis. During combustor operation, the temperature of the air into the combustor is monitored. If the temperature is above a predetermined threshold, fuel is delivered to fewer than all banks of ports. As a result, the bank(s) of ports to which fuel is not delivered inject only air into the combustion chamber, and the other bank(s) of ports inject the air-fuel mixture as usual.

Coogan, Shane B.↗
DOE OSTI2023

GDCI engine with accelerated oil warm-up

A piston oil squirter is selectively opened when an oil temperature is below a threshold oil temperature to transfer heat from the combustion chamber and heat the oil more rapidly when the engine is cold.

Roth, Gregory Thomas↗
DOE OSTI2023

Combustion control using spiking neural networks

A system that controls a combustion engine stores network vectors in a memory that represent diverse and distinct spiking neural networks. The system decodes the network vectors and trains and evaluates the spiking neural networks. The system duplicates selected network vectors and crosses-over the duplicated network vectors that represent modified spiking neural networks. The system mutates the crossed-over duplicated network vectors by randomly modifying one or more portions of the crossing-over duplicated network vectors. The system meter exhaust gas into an intake manifold when an engine temperature exceeds a threshold, an engine load exceeds a threshold, an engine's rotation-per-minute rate exceeds a threshold, and a fuel flow exceeds a threshold. The system modifies fuel flow into an engine's combustion chamber on a cycle-to-cycle basis by the trained spiking neural network.

Puente, Brian P. Maldonado↗
DOE OSTI2024

Gas turbine combustion section having an integrated fuel cell assembly

A combustion section defines an axial direction, a radial direction, and a circumferential direction. The combustion section includes a casing that defines a diffusion chamber. A combustion liner is disposed within the diffusion chamber and defines a combustion chamber. The combustion liner is spaced apart from the casing such that a passageway is defined between the combustion liner and the casing. A fuel cell assembly is disposed in the passageway. The fuel cell assembly includes a fuel cell stack having a plurality of fuel cells each extending between an inlet end and an outlet end. Each fuel cell of the plurality of fuel cells includes an air channel and a fuel channel each fluidly coupled to the combustion chamber.

Hong, Seung-Hyuck↗
DOE OSTI2020

Assessment of turbulent combustion models for simulating pre-chamber ignition in a natural gas engine

Lean combustion in an internal combustion engine is a promising strategy to increase thermal efficiency by leveraging a more favorable specific heat ratio of the fresh mixture and simultaneously suppressing the heat losses to the cylinder wall. However, unstable ignition events and slow flame propagation at fuel-lean condition lead to high cycle-to-cycle variability and hence limit the high-efficiency engine operating range. Pre-chamber ignition is considered an effective concept to extend the lean operating limit, by providing spatially distributed ignition with multiple turbulent flame-jets and enabling faster combustion rate compared to the conventional spark ignition approach. From a numerical modeling perspective, to date, still the science base and available simulation tools are inadequate for understanding and predicting the combustion processes in pre-chamber ignited engines. In this paper, conceptually different RANS combustion models widely adopted in the engine modeling community were used to simulate the ignition and combustion processes in a medium-duty natural gas engine with a pre-chamber spark-ignition system. A flamelet-based turbulent combustion model, i.e., G-equation, and a multi-zone well-stirred reactor model were employed for the multi-dimensional study. Simulation results were compared with experimental data in terms of in-cylinder pressure and heat release rate. Finally, the analysis of the performance of the two models is carried out to highlight the strengths and limitations of the two formulations respectively.

combustion model evaluation↗
DOE OSTI2025

CFD modeling of non-catalytic, partial-oxidation engine reformer for flare mitigation

Flaring associated natural gas is commonly employed in the oil and gas industry to reduce methane (CH 4 ) emissions but generates carbon dioxide (CO 2 ) and harmful pollutants, significantly contributing to air pollution and posing risks to public health. To mitigate this impact, M2X Energy Inc. has developed a small-scale, modular gas-to-methanol system. This system features an engine reformer that performs fuel-rich partial oxidation of wellhead gas to produce syngas—a mixture of carbon monoxide (CO) and hydrogen (H 2 )—followed by a downstream reactor for methanol synthesis. This study focused on computational fluid dynamics (CFD) modeling of the engine reformer to simulate partial oxidation chemistry, predict the rich-burn operating limit, and assess syngas quality, ultimately aiding in design and operational optimization. The CFD model, developed within a Reynolds-Averaged Navier-Stokes (RANS) turbulence framework, incorporated sub-models for turbulent combustion, a chemical mechanism with polycyclic aromatic hydrocarbon (PAH) pathways, and soot emissions to accurately capture the fuel-rich, turbulent jet ignition and combustion processes. Model validation against experimental data showed good agreement across pre- and main-chamber pressures, apparent heat release rates, and exhaust gas concentrations of key species (H 2 , CO, CO 2 , CH 4 ) for varying intake equivalence ratios. Here, the model identified a rich-burn operating limit near a fuel-air equivalence ratio of 2.35, consistent with experimental observations. Furthermore, syngas quality analysis revealed that extending the rich-burn limit through engine reformer optimization could enhance syngas production, contributing to higher methanol synthesis efficiency.

Computational Fluid Dynamics↗
DOE OSTI2025

Chemical Reactor Network Modeling of Ammonia Rich-Quench-Lean Combustion Using a Partially Stirred Reactor Approach

Ammonia is a promising alternative to hydrogen with high energy density and favorable storage and transport characteristics. However, low flammability and a propensity for high nitrogen oxide (NO x ) emissions make direct utilization challenging. Recently, two-stage rich-quench-lean (RQL) combustion strategies have shown promise in achieving low NO x emissions with ammonia. In this approach, the rich stage serves to oxidize a portion of the fuel while thermally decomposing as much of the remaining ammonia as possible, generating hydrogen. In the second (lean) stage, air is rapidly introduced, burning out the hydrogen and residual ammonia. Two-stage RQL combustion of ammonia has been investigated in the open literature both experimentally and numerically. In general, idealized chemical reactor network (CRN) models predict NO x concentrations below those of 2D/3D computational fluid dynamics models and experiments. The primary drivers of these discrepancies may be largely attributed to finite rate mixing nonadiabatic operation. The typical CRN model is comprised of a perfectly-stirred-reactor (PSR), followed by a plug-flow-reactor (PFR), meant to represent the flame, and postflame zones, respectively. In the two-stage RQL approach two PSR-PFR networks are arranged sequentially, corresponding to the rich and lean stages, with secondary air injection in between. In the authors' past work, this arrangement has demonstrated the significant sensitivity of exit NO x to the rich stage equivalence ratio, while the amount of secondary air injection was shown to be less critical. In this paper, the CRN model is extended to (1) include the impacts of heat loss and (2) utilize a partially-stirred-reactor (PaSR) approach to study the impacts of mixing on emissions performance. Varying amounts of heat loss are applied to the rich relaxation zone to understand emissions performance and changes to optimization of equivalence ratio and residence time. Premixed and nonpremixed configurations are considered in the rich stage PaSR, with varying degrees of mixing intensity to study the interaction between mixing, transport, and kinetic timescales. Critically, the impact of mixing between hot products and secondary air injection is studied to understand practical injector needs. Results show unburnt ammonia leaving the rich stage as a primary contributor to NO x emissions – driven both by increased heat loss and reduced mixing rates. Furthermore, heat losses have been shown to create conditions that are conducive to increased N 2 O formation in the lean stage. In conclusion, the results of this study will be considered in the context of developing optimized two-stage RQL combustors for ammonia.

Combustion↗
DOE OSTI2023

Neutronic engine

An internal combustion engine for neutron diffraction analysis is provided. The engine includes an elongated piston chamber formed from an aluminum alloy to ensure maximum neutron visibility into the combustion chamber. An elongated piston assembly reciprocates within the elongated piston chamber, the piston assembly including an upper piston joined to a lower piston. The upper piston and the lower piston are hollow, thereby reducing the reciprocating mass and increasing neutron access to the combustion chamber. The upper piston is lubricated with a neutron-transparent fluorocarbon lubricant such as perfluoropolyether (PFPE), while the lower piston and the crankcase are lubricated with hydrocarbon lubricant. The engine enables 3D and time-resolved measurements of strain, stress, and temperature, as well as phase transformation, texture, and microstructure.

Wissink, Martin L.↗
DOE OSTI2022

Advanced Finite-Volume Numerics and Source Term Assumptions for Kernel and G-Equation Modelling of Propane/Air Flames

Here G-Equation models represent propagating flame fronts with an implicit two-dimensional surface representation (level-set). Level-set methods are fast, as transport source terms for the implicit surface can be solved with finite-volume operators on the finite-volume domain, without having to build the actual surface. However, they include approximations whose practical effects are not properly understood. In this study, we improved the numerics of the FRESCO CFD code’s G-Equation solver and developed a new method to simulate kernel growth using signed distance functions and the analytical sphere-mesh overlap. We analyzed their role for simulating propane/air flames, using three well-established constant-volume configurations: a one-dimensional, freely propagating laminar flame; a disc-shaped, constant-volume swirl combustor; and torch-jet flame development through an orifice from a two-chamber device. We tested the explicit (sub-cycled) vs. implicit formulation for the standard transport operators (advection, diffusion, compressibility). In addition to the accurate flame swept-volume method for chemistry and species source term, we developed a more accurate estimator for the burnt/unburnt split cell composition. Then, we developed a signed-distance-function (SDF) based method which provides a more stable reinitialization of the level-set field at every time-step. We found that simplifying assumptions common to several G-Equation implementations, for straightforward terms such as compressibility and advection, lead to large errors in predicting the propagation of even laminar flames, with deviations up to ~300% in simulated vs. formulated flame speed. Conversely, the enhanced numerics enabled through the SDF field reinitialization and improved chemistry source term improve simulation stability and smooth flame propagation even with significantly larger solver time-steps.

42 ENGINEERING↗
DOE OSTI2020

Significance of the Direct Excitation Mechanism for High-Frequency Response of Premixed Flames to Flow Oscillations

Premixed flames are sensitive to flow disturbances, which can arise from acoustic or vortical fluctuations. For transverse instabilities, it is known that a dominant mechanism for flame response is “injector coupling,” whereby pressure oscillations associated with transverse waves excite axial flow disturbances. These axial flow disturbances then excite heat release oscillations. The objective of this paper is to consider another mechanism—the direct sensitivity of the unsteady heat release to transverse acoustic waves—and to compare its significance relative to the induced axial disturbances, in a linear framework. The rate at which the flame adds energy to the disturbance field is quantified using the Rayleigh criterion and evaluated over a range of control parameters, such as flame length and swirl number. The results show that radial modes induce heat release fluctuations that always add energy to the acoustic field, whereas heat release fluctuations induced by mixed radial-azimuthal modes can add or remove energy. These amplification rates are then compared to the flame response from induced axial fluctuations. For combustor-centered flames, these results show that the direct excitation mechanism has negligible amplification rates relative to the induced axial mechanism for radial modes. For transverse modes, the fact that the nozzle is located at a pressure node indicates that negligible induced axial velocity disturbances are excited; as such, the direct mechanism dominates. As a result, for flames that are not centered on pressure nodes, the direct mechanism for mixed modes dominates for certain nozzle locations and flame angles.

42 ENGINEERING↗
DOE OSTI2021

Describing the Mechanism of Instability Suppression Using a Central Pilot Flame With Coupled Experiments and Simulations

Pilot flames are commonly used to extend combustor operability limits and suppress combustion oscillations in low-emissions gas turbines. Combustion oscillations, a coupling between heat release rate oscillations and combustor acoustics, can arise at the operability limits of low-emissions combustors where the flame is more susceptible to perturbations. While the use of pilot flames is common in land-based gas turbine combustors, the mechanism by which they suppress instability is still unclear. In this study, we consider the impact of a central jet pilot on the stability of a swirl-stabilized flame in a variable-length, single-nozzle combustor. Previously, the pilot flame was found to suppress the instability for a range of equivalence ratios and combustor lengths. We hypothesize that combustion oscillation suppression by the pilot occurs because the pilot provides hot gases to the vortex breakdown region of the flow that recirculate and improve the static, and hence dynamic, stability of the main flame. This hypothesis is based on a series of experimental results that show that pilot efficacy is a strong function of pilot equivalence ratio but not pilot flow rate, which would indicate that the temperature of the pilot products as well as the combustion intensity of the pilot flame play more of a role in oscillation stabilization than the length of the pilot flame relative to the main flame. Further, the pilot-flame efficacy increases with pilot-flame equivalence ratio until it matches the main-flame equivalence ratio; at pilot equivalence ratios greater than the main equivalence ratio, the pilot-flame efficacy does not change significantly with pilot equivalence ratio. To understand these results, we use large-eddy simulation (LES) to provide a detailed analysis of the flow in the region of the pilot flame and the transport of radical species in the region between the main flame and pilot flame. Furthermore, the simulation, using a flamelet/progress variable-based chemistry tabulation approach and standard eddy viscosity/diffusivity turbulence closure models, provides detailed information that is inaccessible through experimental measurements.

42 ENGINEERING↗
DOE OSTI2021

Optimum Multinozzle Configuration for Minimizing the Rayleigh Integral During High-Frequency Transverse Instabilities

This paper develops a formalism for optimizing nozzle location/configuration with respect to combustion stability of high-frequency transverse modes in a can combustor. The stability of these acoustically noncompact flames was assessed using the Rayleigh integral (RI). Several key control parameters influence RI—flame angle, swirling strength, nozzle location, as well as nozzle location with respect to the acoustic mode shape. In this study, we consider a N-around-1 configuration such as typically used in a multi-nozzle can system and study the overall stability of this system for different natural transverse modes. Typically, such nozzles are distributed in a uniformly circular manner for which we study the overall RI, and for cases where RI > 0, we optimize the nozzle distribution that can reduce and minimize RI. For a fixed geometry such as a circular configuration, the analysis shows how the flame's parameters must vary across the different nozzles, to result in a relatively stable system. Additionally, for a fixed set of flame parameters, the analysis also indicates the noncircular distribution of the N nozzles that minimizes RI. Overall, the analysis aims to provide insights on designing nozzle locations around the center nozzle for minimal amplification of a given transverse mode.

42 ENGINEERING↗
DOE OSTI2022

Experimental Investigation of Interactions Between Two Closely Spaced Azimuthal Modes in a Multinozzle Can Combustor

Thermoacoustic instabilities in annular or circular combustors are often coupled with azimuthal modes. These modes can be characterized by a spin ratio (SR), which quantifies the dominant mode between two counter-rotating waves, and a phase difference between them, which is directly related to the orientation of the antinodal line. This study investigates the instability amplitudes, SR, and phase difference of two closely spaced (3% of their mean frequency), yet distinct azimuthal modes; one is the first azimuthal (1A) mode, and the other is a combination of first azimuthal and first longitudinal (1A1L) mode. Each mode itself consists of two peaks that are spaced even more closely in frequency (0.8%). Furthermore, distinct harmonics at 2× and 3× of these frequencies, presumably associated with nonlinearities, are also evident in the spectra. Each mode is bandpass filtered in spectrum to analyze them separately. For the 1A mode, the SR and phase difference exhibit a variety of behaviors—including quasi-periodic standing waves, spinning waves, and intermittency—depending on operating conditions such as thermal power and azimuthal fuel staging. Similar trends are observed for the 1A1 L mode. Moreover, there is clear coupling between the 1A and 1A1 L modes, as their SRs are almost synchronized during the quasi-periodic standing wave. This synchronization is observed in phase differences as well, but not in the instability amplitude. For spinning dominant wave conditions, the SRs of each mode have similar average values, but they fluctuate in a seemingly random fashion. For the phase difference, both average and fluctuation are not correlated. In contrast, the instability amplitudes are strongly correlated, with modulation of the 1A mode leading to that of the 1A1 L mode. Furthermore, these results clearly indicate that complex coupling occurs across closely spaced frequencies under instability conditions, coupling that must be understood in order to capture limit cycle dynamics.

33 ADVANCED PROPULSION SYSTEMS↗