Search NASA⌕ Search

SEARCH · Search NASA

Results for “compression ignition engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Demonstration of Better than Diesel Efficiency and Soot Emissions using Gasoline Compression Ignition in a Light Duty Engine with a Fuel Pressure Limitation

Increasing regulatory demand to reduce CO2 emissions has led to a focus on advanced combustion strategy development to improve overall engine efficiency. Gasoline compression ignition (GCI) has been demonstrated by others to have the potential to meet future CO2 regulations and emissions while achieving comparable to better efficiency than conventional diesel compression ignition (DCI). Soot and NOx emissions are also reduced significantly by using gasoline instead of diesel in compression ignition engines due to differences in composition, fuel properties, and reactivity. In comparison with diesel fuel, gasoline has a higher volatility and more resistance to autoignition, therefore, its longer ignition delay time will allow for better mixing of the air-fuel charge before combustion. In this study, a GCI combustion system has been tested in a Hyundai 2.2L engine as part of a US Department of Energy funded project. A double-injection strategy was tested from mid-to-high loads (5-20 bar BMEP) and for engine speeds in the range of 1200-3000 rpm. Up to 43.4% brake thermal efficiency was achieved using the GCI mode versus 41% using DCI mode. The GCI mode has demonstrated two distinct strategies that work at different load ranges, partially premixed compression ignition (PPCI) and mixing-controlled compression ignition (MCCI). Overall, this study shows that for similar engine-out NOx levels, GCI mode had higher brake thermal efficiency than DCI with lower fuel pressure and EGR required.

02 PETROLEUM↗
DOE OSTI2023

Artificial Neural Network Models for Octane Number and Octane Sensitivity: A Quantitative Structure Property Relationship Approach to Fuel Design

Octane sensitivity (OS), defined as the research octane number (RON) minus the motor octane number (MON) of a fuel, has gained interest among researchers due to its effect on knocking conditions in internal combustion engines. Compounds with a high OS enable higher efficiencies, especially within advanced compression ignition engines. RON/MON must be experimentally tested to determine OS, requiring time, funding, and specialized equipment. Thus, predictive models trained with existing experimental data and molecular descriptors (via quantitative structure-property relationships (QSPRs)) would allow for the preemptive screening of compounds prior to performing these experiments. Here, the present work proposes two methods for predicting the OS of a given compound: using artificial neural networks (ANNs) trained with QSPR descriptors to predict RON and MON individually to compute OS (derived octane sensitivity (dOS)), and using ANNs trained with QSPR descriptors to directly predict OS. Twenty-five ANNs were trained for both RON and MON and their test sets achieved an overall 6.4% and 5.2% error, respectively. Twenty-five additional ANNs were trained for both dOS and OS; dOS calculations were found to have 15.3% error while predicting OS directly resulted in 9.9% error. A chemical analysis of the top QSPR descriptors for RON/MON and OS is conducted, highlighting desirable structural features for high-performing molecules and offering insight into the inner mathematical workings of ANNs; such chemical interpretations study the interconnections between structural features, descriptors, and fuel performance showing that connectivity, structural diversity, and atomic hybridization consistently drive fuel performance.

09 BIOMASS FUELS↗
NASA NTRS1940

A Method of Measuring Piston Temperatures

A method that makes use of thermocouples has been developed to measure the temperature of engine pistons operating at high speeds. The thermocouples installed on the moving piston are connected with a potentiometer outside the engine by means of pneumatically operated plungers, which make contact with the piston thermocouples for about 10 crankshaft degrees at the bottom of the piston stroke. The equipment is operated satisfactory at engine speeds of 2,400 r.p.m. and shows promise of successful operation at higher engine speeds. Measurements of piston temperatures in a liquid-cooled compression-ignition engine and in an air-cooled spark-ignition are presented.

Pinkel, Benjamin↗
DOE OSTI2024

Understanding the ignition process and flame structure of conventional and oxygenated fuels under engine relevant conditions – An optical study

Renewably generated synthetic fuels such as poly-oxymethylene ethers (OME) have a significant potential to effectively break the soot-NOX trade-off in compression ignition engines by using exhaust gas recirculation (EGR) to maintain low nitrogen oxide (NOX) emissions while maintaining good efficiency and simultaneously contributing to circular carbon economy. However, owing to the fundamental differences in properties of OME when compared to fossil-based diesel fuels, it is critical to fully understand its ignition and combustion phenomenology to take advantage of this fuel to its utmost potential. In this context, this work outlines the results of a systematic experimental study performed in a heavy-duty, single-cylinder, optical engine probing the spatial and temporal progression of fuel decomposition and ignition behavior of OME when compared to n-dodecane, a diesel-fuel surrogate. Thermodynamic analysis and optical diagnostics techniques including simultaneous HCHO-PLIF and OH-PLIF complemented by high-speed OH* chemiluminescence were employed along with parametric sweeps of intake temperature and EGR dilution rates. OME does not exhibit any observable low temperature heat release irrespective of the ambient oxygen concentration. Differences in the observed diffusive flame structure such as longer flame lift-off length, less pronounced combustion recession, faster premixed burn at ignition (“volumetric” ignition), non-sooting behavior suggest that the inherent presence of fuel-bound oxygen in OME can skew the air-fuel ratio (AFR) distribution within the jet thereby reducing the reliance of combustion on mixing and air entrainment. This leads to rapid late-cycle oxidation leading to shorter combustion duration and favorable combustion phasing. Results also suggest that OME exhibits relatively weak negative temperature coefficient (NTC) behavior, however, the OME fuel-decomposition kinetic-pathways produce significant concentration of HCHO, which might be erroneously interpreted as a product of cool-flames.

Air-fuel ratio↗
DOE OSTI2020

Prediction of Research/Motor Octane Number and Octane Sensitivity Using Artificial Neural Networks

Octane sensitivity (OS), dfined as the research octane number (RON) minus the motor octane number (MON) of a given fuel, has gained interest among researchers due to its apparent ffect on knocking conditions in internal combustion engines. Compounds with a high OS enable higher efficiencies, especially with respect to advanced compression ignition engines. RON/MON must be experimentally tested to determine OS; however, the experimental methods utilized require a substantial amount of time, a significant monetary investment, and specialized equipment. To this end, predictive computational models trained with existing experimental data and molecular properties would allow for the preemptive screening of compounds prior to performing these experiments. The present work proposes two methods for predicting the OS of a given compound: using artficial neural networks (ANNs) trained with quantitative structure-property relationship (QSPR) descriptors to predict RON and MON individually to compute OS from RON/MON predictions (derived octane sensitivity, dOS), and using an ANN trained with QSPR descriptors to directly predict OS. ANNs trained to predict RON and MON achieved test set root-mean-square errors (RMSEs) of 10.499 and 7.551 respectively. dOS calculations were found to have a test set RMSE of 6.432 while predicting OS directly resulted in a test set RMSE of 7.019, showing it is more bene cial to obtain OS from RON/MON predictions than predicting it directly. Furthermore, relationships between individual QSPR descriptors and RON/MON/OS are discussed, highlighting correlations between specfic molecular features and these properties.

09 BIOMASS FUELS↗
DOE OSTI2020

Material-Dependent Antagonistic Effects between Soot and ZDDP

While soot in engine oil is known to accelerate the wear of diesel and gasoline direct-injection compression-ignition engines, there is a lack of consensus on the wear mechanism though various hypotheses have been proposed in the literature. Particularly, some recently observed antagonistic effects between soot and a common lubricant antiwear additive, zinc dialkyldithiophosphate (ZDDP), while others did not. The discrepancy is, in part, explained by the strong alloy dependence of such antagonism discovered in this study. Specifically, four alloys, 52100 steel and M2, M50, and A2 tool steels, are tested in lubricants containing carbon black (CB, a soot surrogate) with and without ZDDP present. Adding the CB alone to the oil increases the wear rate for all steel alloys as expected. However, distinct wear performance is observed for the four steel alloys when ZDDP is introduced to the CB-containing oil: while the 52100 steel has notable wear reduction, the three tool steels suffer significant wear increase. Comprehensive tribofilm characterization suggests that the Mo content in the steel alloy and the sulfur from ZDDP strongly influence wear behavior. The combination of CB/Mo-catalyzed sulfidation and CB-accelerated abrasion is hypothesized to be responsible for the high wear of the Mo-alloyed tool steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ducted Fuel Injection vs. Conventional Diesel Combustion: Extending the Load Range in an Optical Engine with a Four-Orifice Fuel Injector

Ducted fuel injection (DFI) is a technique to attenuate soot formation in compression ignition engines relative to conventional diesel combustion (CDC). The concept is to inject fuel through a small tube inside the combustion chamber to reduce equivalence ratios in the autoignition zone relative to CDC. DFI has been studied at loads as high as 8.5 bar gross indicated mean effective pressure (IMEP g ) and as low as 2.5 bar IMEP g using a four-orifice fuel injector. Across previous studies, DFI has been shown to attenuate soot emissions, increase NO x emissions (at constant charge dilution), and slightly decrease fuel conversion efficiencies for most tested points. This study expands on the previous work by testing 1.1 bar IMEPg (low-load/idle) conditions and 10 bar IMEPg (higher-load) conditions with the same four-orifice fuel injector, as well as examining potential causes of the degradations in NO x emissions and fuel conversion efficiencies. DFI and CDC are directly compared at each operating point in the study. At the low-load condition, the intake charge dilution was swept to elucidate the soot and NO x performance of DFI. The low-load range is important because it is the target of impending, more-stringent emissions regulations, and DFI is shown to be a potentially effective approach for helping to meet these regulations. The results also indicate that DFI likely has slightly decreased fuel conversion efficiencies relative to CDC. We find that the increase in NO x emissions with DFI is likely due to longer charge gas residence times at higher temperatures, which arise from shorter combustion durations and advanced combustion phasing relative to CDC.

42 ENGINEERING↗
NASA NTRS1939

A Comparison of Ignition Characteristics of Diesel Fuels as Determined in Engines and in a Constant-volume Bomb

Ignition-lag data have been obtained for seven fuels injected into heated, compressed air under conditions simulating those in a compression-ignition engine. The results of the bomb tests have been compared with similar engine data, and the differences between the two sets of results are explained in terms of the response of each fuel to variations in air density and temperature.

Selden, Robert F↗
DOE OSTI2025

Predicting Fuel Properties and Emissions for Advanced Biofuels for Diesel Engines (CRADA Final Report)

The project will investigate variations in biofuel composition and optimize performance in combustion for conventional and future compression ignition engines. It will evaluate a variety of bio-derived molecules in the diesel range that can be produced using technology in ExxonMobil’s portfolio as well as fuels that cover the range of potential molecular structures for robust model development. Changes in fuel/air premixing and stratification in advanced engines could alter the relationship between fuel properties and performance in comparison to current generation spray combustion approaches. NREL experience in fuel and combustion modeling will enable development of general rules for predicting performance of a wide range of biofuel options.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Ignition delay time and speciation of dibutyl ether at high pressures

Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550–650 K, P = 10, 20, 40 bar, φ = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900–1300 K, P = 20, 40 bar, φ = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100–1400 K, P = 20 bar. Pressure time-histories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. We found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.

09 BIOMASS FUELS↗
NASA NTRS1992

Three-dimensional modeling of diesel engine intake flow, combustion and emissions

A three-dimensional computer code (KIVA) is being modified to include state-of-the-art submodels for diesel engine flow and combustion: spray atomization, drop breakup/coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, soot and radiation, and the intake flow process. Improved and/or new submodels which were completed are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NOx, and spray/wall impingement with rebounding and sliding drops. Results to date show that adding the effects of unsteadiness and compressibility improves the accuracy of heat transfer predictions; spray drop rebound can occur from walls at low impingement velocities (e.g., in cold-starting); larger spray drops are formed at the nozzle due to the influence of vaporization on the atomization process; a laminar-and-turbulent characteristic time combustion model has the flexibility to match measured engine combustion data over a wide range of operating conditions; and finally, the characteristic time combustion model can also be extended to allow predictions of ignition. The accuracy of the predictions is being assessed by comparisons with available measurements. Additional supporting experiments are also described briefly. To date, comparisons with measured engine cylinder pressure and heat flux data were made for homogeneous charge, spark-ignited and compression-ignited engines. The model results are in good agreement with the experiments.

Reitz, R. D.↗
DOE OSTI2023

Development of a High-Pressure Fuel Injection System for Use with Propane-DME

Paper details the design approach and performance of a high-pressure common rail fuel injection system used with Propane-DME mixtures targeting high injection pressures on a light duty 2.2L inline-4 compression ignition engine. The study estimates the bulk modulus of elasticity based on the hardware geometry and operating pressures to assess the compressibility of Propane and DME across a range of pressures typical of the LD engine application. The compressibility factor ranges from 500 to 3000 bar, significantly lower than the theoretical values for the conditions tested. The high-pressure pump performance is optimized via the implementation of an inlet metering valve operated on a crank-angle open/close sequence to control pressure at the common rail. The application of a model-based controller and the use of high-speed sampling of rail pressure indicate that pressure at the rail can be attained with the pump metering valve, and without use of the pressure relieve valve present in the rail. Results show a significant reduction on pumping work parasitics and of fuel heating, on the order of 40°C, at typical working conditions with the proposed approach. Injector rates of injection with Propane-DME are very similar to those of Diesel. Paper compares bench data of rates of injection versus simulation predictions across operating pressures of 200 to 1000bar and from injection commands spanning 0.20 to 2.0ms. Furthermore, the accuracy of the model predictions are attributed in part by to the updated fuel compressibility modulus descriptions attained during the testing.

42 ENGINEERING↗
NASA NTRS2001

New Technology Sparks Smoother Engines and Cleaner Air

Automotive Resources, Inc. (ARI) has developed a new device for igniting fuel in engines-the SmartPlug.TM SmartPlug is a self-contained ignition system that may be retrofitted to existing spark-ignition and compression-ignition engines. The SmartPlug needs as little as six watts of power for warm-up, and requires no electricity at all when the engine is running. Unlike traditional spark plugs, once the SmartPlug ignites the engine, and the engine heats up, the power supply for the plug is no longer necessary. In the utility industry, SmartPlugs can be used in tractors, portable generators, compressors, and pumps. In addition to general-purpose applications, such as lawn mowers and chainsaws, SmartPlugs can also be used in the recreational, marine, aviation, and automotive industries. Unlike traditional ignition systems, the SmartPlug system requires no distributor, coil points, or moving parts. SmartPlugs are non-fouling, with a faster and cleaner burn than traditional spark plugs. They prevent detonation and are not sensitive to moisture, allowing them to be used on a variety of engines. Other advantages include no electrical noise, no high voltage, exceptionally high altitude capabilities, and better cold-start statistics than those of standard spark ignition systems. Future applications for the SmartPlug are being evaluated by manufacturers in the snowmobile industry.

Source record↗
DOE OSTI2023

A Computational Investigation of Engine Heat Transfer with Ducted Fuel Injection

Ducted fuel injection (DFI) is an innovative method that curtails or prevents soot formation in direct-injection compression-ignition engines. DFI uses a simple duct, positioned outside each injector hole, facilitating the fuel/charge gas mixing before ignition. This reduces the equivalence ratio below two, in the autoignition zone, which in turn decreases soot formation. But this method also reduces fuel-conversion efficiency. This study investigates the effects of DFI on in-cylinder heat transfer. Experiments with conventional diesel combustion (CDC) and DFI were performed at four different dilution levels. Computational fluid dynamics (CFD) simulations were carried out at conditions matching those of the experiments, and the simulations were validated by the experimental data. The CFD simulations enabled to examine of in-cylinder heat release and temperature distributions. The heat transfer to the piston, head, and cylinder was investigated. The results show that DFI increased the heat transfer to the walls compared to CDC under the same conditions. This could help explain why DFI has been observed to reduce fuel-conversion efficiency by approximately 1% (absolute) relative to CDC under certain conditions. The efficiency loss typically decreases with dilution, such that DFI can improve fuel-conversion efficiencies relative to CDC at higher dilution levels.

Şener, Ramazan↗
DOE OSTI2023

Design optimization of an ethanol heavy-duty engine using design of experiments and bayesian optimization

Diesel-fueled engines still hold a large market share in the medium and heavy-duty transportation sector. However, the increase in fossil fuel prices and the strict emission regulations are leading engine manufacturers to seek cleaner alternatives without a compromise in performance. Alcohol-based fuels, such as ethanol, offer a promising alternative to diesel fuel in meeting regulatory demands. Ethanol provides cleaner combustion and lower levels of soot due to its chemical properties, in particular its lower level of carbon content. In addition, the stoichiometric operating conditions of alcohol fueled engines enable the mitigation of NOx emissions in aftertreatment stage. With the promise of retrofitting diesel engines to run on ethanol to reduce emissions, the thermal efficiency of these engines remains the primary optimization target. In order to find the optimal ethanol-fueled engine design that maximizes the thermal efficiency, a large design space needs to be investigated using engineering tools. In this study, previous research by the authors on optimizing the design of a single-cylinder ethanol-fueled engine was extended to explore the design space for a heavy-duty multi-cylinder engine configuration. A heavy-duty engine setup with multiple operating conditions at different engine speeds and loads were considered. A design optimization analysis was performed to identify the potential designs that maximize the indicated thermal efficiency in an ethanol-fueled compression ignition engine. First, a computational fluid dynamics (CFD) model of the engine was validated using experimental data for four drive cycle points. Using a design of experiments (DoE) approach and a parameterized piston bowl geometry, the model was then exercised to explore the relationship among geometric features of the piston bowl and spray targeting angle and indicated thermal efficiency across all tested operating conditions. After evaluating 165~candidate designs, a piston bowl geometry was identified that yielded an increase between 1.3 to 2.2 percentage points in indicated thermal efficiency for all tested conditions, while satisfying the operational design constraints for peak pressure and maximum pressure rise rate. The increased performance was attributed to enhanced mixing that led to the formation of a more homogeneous distribution of in-cylinder temperature and equivalence ratio, higher combustion temperatures, and shorter combustion duration. Finally, a Bayesian optimization (BOpt) analysis was employed to find the optimal piston bowl geometry with a fixed spray injector angle for one of the operating conditions. Using BOpt, a piston candidate was identified that resulted in a 1.9~percentage point increase in thermal efficiency from the baseline design, yet only required 65\% of the design samples investigated using the DoE approach.

Tekgul, Bulut↗
NASA NTRS1932

Preliminary Tests on the Vaporization of Fuel Sprays

High-speed motion pictures were taken of fuel sprays injected into the combustion chamber of the N.A.C.A. combustion apparatus. Three fuels, ethyl alcohol, gasoline, and fuel oil, which differed considerably in volatility were tested. By maintaining the engine temperature below that required for ignition the spray could be studied from soon after the start of injection until 130 crank degrees later. The results show that the sprays vaporize appreciably so that it is possible for the ignition in high speed compression-ignition engines to take place from the vapor phase.

Rothrock, A M↗
DOE OSTI2020

Ducted Fuel Injection vs. Free-Spray Injection: A Study of Mixing and Entrainment Effects Using Numerical Modeling

Diesel engines are an important technology for transportation of both people and goods. However, historically they have suffered a significant downside of high soot and nitrogen oxides (NO x ) emissions. Recently, ducted fuel injection (DFI) has been demonstrated to attenuate soot formation in compression-ignition engines and combustion vessels by 50% to 100%. This allows for diesel engines to be run at low-NO x emissions that would have otherwise produced significantly more soot due to the soot/NO x tradeoff. Currently the root causes of this soot attenuation are not well understood. To be able to better optimize DFI for use across a variety of engines and conditions, it is important to understand clearly how it works. This study expands on the current understanding of DFI by using numerical modeling under nonreacting conditions to provide insights about the roles of entrainment and mixing that would have been much more challenging to obtain experimentally. We report this study found that DFI enhances charge gas entrainment upstream of the duct and blocks entrainment inside of the duct. Mixing is enhanced by the duct, which results in lower peak equivalence ratios at the exit of the duct.

42 ENGINEERING↗
NASA NTRS1932

Experiments on the Distribution of Fuel in Fuel Sprays

The distribution of the fuel in sprays for compression-ignition engines was investigated by taking high-speed spark photographs of fuel sprays produced under a wide variety of conditions, and also by injecting them against pieces of Plasticine. A photographic study was made of sprays injected into evacuated chambers, into the atmosphere, into compressed air, and into transparent liquids. Pairs of identical sprays were injected counter to each other and their behavior analyzed. Small high-velocity air jets were directed normally to the axes of fuel sprays, with the result that the envelope of spray which usually obscures the core was blown aside, leaving the core exposed on one side.

Lee, Dana W↗