Results for “data reconstruction” — Page 6

NASA NTRS1983

Reconstruction of the shuttle reentry air data parameters using a linearized Kalman filter

This paper presents the reconstruction of the space shuttle's wind-relative reentry trajectory for the orbital flights. The technique uses a linearized Kalman filter (LKF) to merge highand low-frequency inertial and wind-relative data to obtain enhanced high-frequency results that closely follow expected mean levels. Two verifications are presented. First, wind trajectories resulting from the reconstruction are compared with analytically predicted values. There is close comparison. Second, the frequency characteristics are investigated using system identification techniques. The stability and control model generated using the LKF trajectory shows good agreement between measured and predicted spacecraft response for both high and low frequencies.

Whitmore, S. A.↗

NASA NTRSDate not supplied

Kamodo’s Satellite Constellation Mission Planning Tool

Kamodo provides a functional model-agnostic interface to a growing collection of Heliophysics model outputs. The CCMC, in collaboration with the Geospace Dynamics Constellation Science Team, has recently developed Kamodo’s satellite constellation mission planning tool to perform reconstructions in any pair of dimensions, including time. The ‘reconstruction’ tool enables users to fly any 4-dimensional grid of satellites through a given model data set, reconstructing what the given constellation would observe during the mission. This capability facilitates determination of what satellite configuration is best for a given science question, even allowing comparison across multiple models. This tool, written in Python, is built upon Kamodo’s flythrough tool, which in turn depends on a growing network of model-specific interfaces. Since each model interface is designed with model-agnostic syntax, the flythrough tool and the satellite constellation mission planning tool also feature model-agnostic syntax. In this work, we will describe the basic analysis choices available in the tool and provide a variety of sample workflows. The tool is freely available at https://github.com/nasa/Kamodo for the public. We invite the community to use the reconstruction tool and adapt the provided workflows for their mission planning, and to contribute their own workflows to share with others.

software↗

NASA NTRSDate not supplied

SM25C-2002: Kamodo’s Satellite Constellation Mission Planning Tool

Kamodo provides a functional model-agnostic interface to a growing collection of Heliophysics model outputs. The CCMC, in collaboration with the Geospace Dynamics Constellation Science Team, has recently developed Kamodo’s satellite constellation mission planning tool to perform reconstructions in any pair of dimensions, including time. The ‘reconstruction’ tool enables users to fly any 4-dimensional grid of satellites through a given model data set, reconstructing what the given constellation would observe during the mission. This capability facilitates determination of what satellite configuration is best for a given science question, even allowing comparison across multiple models. This tool, written in Python, is built upon Kamodo’s flythrough tool, which in turn depends on a growing network of model-specific interfaces. Since each model interface is designed with model-agnostic syntax, the flythrough tool and the satellite constellation mission planning tool also feature model-agnostic syntax. In this work, we will describe the basic analysis choices available in the tool and provide a variety of sample workflows. The tool is freely available at https://github.com/nasa/Kamodo for the public. We invite the community to use the reconstruction tool and adapt the provided workflows for their mission planning, and to contribute their own workflows to share with others.

python↗

NASA NTRS1988

Extraction of topography from side-looking satellite systems - A case study with SPOT simulation data

A simulated data set was used to evaluate techniques for extracting topography from side-looking satellite systems for an area of northwest Washington state. A negative transparency orthophotoquad was digitized at a spacing of 85 microns, resulting in an equivalent ground distance of 9.86 m between pixels and a radiometric resolution of 256 levels. A bilinear interpolation was performed on digital elevation model data to generate elevation data at a 9.86-m resolution. The nominal orbital characteristics and geometry of the SPOT satellite were convoluted with the data to produce simulated panchromatic HRV digital stereo imagery for three different orbital paths and techniques for reconstructing topographic data were developed. Analyses with the simulated HRV data and other data sets show that the method is effective.

Ungar, Stephen G.↗

NASA NTRS2022

Quantifying Errors in 3D CME Parameters Derived from Synthetic Data Using White-Light Reconstruction Techniques

Current efforts in space weather forecasting of CMEs have been focused on predicting their arrival time and magnetic structure. To make these predictions, methods have been developed to derive the true CME speed, size, position, and mass, among others. Difficulties in determining the input parameters for CME forecasting models arise from the lack of direct measurements of the coronal magnetic fields and uncertainties in estimating the CME 3D geometric and kinematic parameters after eruption. White-light coronagraph images are usually employed by a variety of CME reconstruction techniques that assume more or less complex geometries. This is the first study from our International Space Science Institute (ISSI) team “Understanding Our Capabilities in Observing and Modeling Coronal Mass Ejections”, in which we explore how subjectivity affects the 3D CME parameters that are obtained from the Graduated Cylindrical Shell (GCS) reconstruction technique, which is widely used in CME research. To be able to quantify such uncertainties, the “true” values that are being fitted should be known, which are impossible to derive from observational data. We have designed two different synthetic scenarios where the “true” geometric parameters are known in order to quantify such uncertainties for the first time. We explore this by using two sets of synthetic data: 1) Using the ray-tracing option from the GCS model software itself, and 2) Using 3D magnetohydrodynamic (MHD) simulation data from the Magnetohydrodynamic Algorithm outside a Sphere code. Our experiment includes different viewing configurations using single and multiple viewpoints. CME reconstructions using a single viewpoint had the largest errors and error ranges overall for both synthetic GCS and simulated MHD white-light data. As the number of viewpoints increased from one to two, the errors decreased by approximately 4° in latitude, 22° in longitude, 14° in tilt, and 10° in half-angle. Our results quantitatively show the critical need for at least two viewpoints to be able to reduce the uncertainty in deriving CME parameters. We did not find a significant decrease in errors when going from two to three viewpoints for our specific hypothetical three spacecraft scenario using synthetic GCS white-light data. As we expected, considering all configurations and numbers of viewpoints, the mean absolute errors in the measured CME parameters are generally significantly higher in the case of the simulated MHD white-light data compared to those from the synthetic white-light images generated by the GCS model. We found the following CME parameter error bars as a starting point for quantifying the minimum error in CME parameters from white-light reconstructions: Δθ (latitude)=6° +2° -3° , Δϕ (longitude)=11° +18° -6° , Δγ (tilt)=25° +8° -7° , Δx (half-angle)=10° +12° -6° , Δh (height)=0.6 +1.2 -0.4 R ⨀ , and Δκ (ratio)=0.1 +0.03 -0.02 .

Coronal mass ejections↗

NASA NTRS2022

Quantifying Errors in 3D CME Parameters Derived From Synthetic Data Using White-Light Reconstruction Techniques

Current efforts in space weather forecasting of CMEs have been focused on predicting their arrival time and magnetic structure. To make these predictions, methods have been developed to derive the true CME speed, size, position, and mass, among others. Difficulties in determining the input parameters for CME forecasting models arise from the lack of direct measurements of the coronal magnetic fields and uncertainties in estimating the CME 3D geometric and kinematic parameters after eruption. White-light coronagraph images are usually employed by a variety of CME reconstruction techniques that assume more or less complex geometries. This is the first study from our International Space Science Institute (ISSI) team “Understanding Our Capabilities in Observing and Modeling Coronal Mass Ejections”, in which we explore how subjectivity affects the 3D CME parameters that are obtained from the Graduated Cylindrical Shell (GCS) reconstruction technique, which is widely used in CME research. To be able to quantify such uncertainties, the “true” values that are being fitted should be known, which are impossible to derive from observational data. We have designed two different synthetic scenarios where the “true” geometric parameters are known in order to quantify such uncertainties for the first time. We explore this by using two sets of synthetic data: 1) Using the ray-tracing option from the GCS model software itself, and 2) Using 3D magnetohydrodynamic (MHD) simulation data from the Magnetohydrodynamic Algorithm outside a Sphere code. Our experiment includes different viewing configurations using single and multiple viewpoints. CME reconstructions using a single viewpoint had the largest errors and error ranges overall for both synthetic GCS and simulated MHD white-light data. As the number of viewpoints increased from one to two, the errors decreased by approximately 4° in latitude, 22° in longitude, 14° in tilt, and 10° in half-angle. Our results quantitatively show the critical need for at least two viewpoints to be able to reduce the uncertainty in deriving CME parameters. We did not find a significant decrease in errors when going from two to three viewpoints for our specific hypothetical three spacecraft scenario using synthetic GCS white-light data. As we expected, considering all configurations and numbers of viewpoints, the mean absolute errors in the measured CME parameters are generally significantly higher in the case of the simulated MHD white-light data compared to those from the synthetic white-light images generated by the GCS model. We found the following CME parameter error bars as a starting point for quantifying the minimum error in CME parameters from white-light reconstructions: Δθ (latitude)=6° +2° -3° , Δϕ (longitude)=11° +18° -6° , Δγ (tilt)=25° +8° -7° , Δx (half-angle)=10° +12° -6° , Δh (height)=0.6 +1.2 -0.4 R ⨀ , and Δκ (ratio)=0.1 +0.03 -0.02 .

Coronal mass ejections↗

NASA NTRS2011

Ares I-X Separation and Reentry Trajectory Analyses

The Ares I-X Flight Test Vehicle was launched on October 28, 2009 and was the first and only test flight of NASA s two-stage Ares I launch vehicle design. The launch was successful and the flight test met all of its primary and secondary objectives. This paper discusses the stage separation and reentry trajectory analysis that was performed in support of the Ares I-X test flight. Pre-flight analyses were conducted to assess the risk of stage recontact during separation, to evaluate the first stage flight dynamics during reentry, and to define the range safety impact ellipses of both stages. The results of these pre-flight analyses were compared with available flight data. On-board video taken during flight showed that the flight test vehicle successfully separated without any recontact. Reconstructed trajectory data also showed that first stage flight dynamics were well characterized by pre-flight Monte Carlo results. In addition, comparisons with flight data indicated that the complex interference aerodynamic models employed in the reentry simulation were effective in capturing the flight dynamics during separation. Finally, the splash-down locations of both stages were well within predicted impact ellipses.

Tartabini, Paul V.↗

NASA NTRS2015

Post-Flight Aerodynamic and Aerothermal Model Validation of a Supersonic Inflatable Aerodynamic Decelerator

NASA's Low Density Supersonic Decelerator Program is developing new technologies that will enable the landing of heavier payloads in low density environments, such as Mars. A recent flight experiment conducted high above the Hawaiian Islands has demonstrated the performance of several decelerator technologies. In particular, the deployment of the Robotic class Supersonic Inflatable Aerodynamic Decelerator (SIAD-R) was highly successful, and valuable data were collected during the test flight. This paper outlines the Computational Fluid Dynamics (CFD) analysis used to estimate the aerodynamic and aerothermal characteristics of the SIAD-R. Pre-flight and post-flight predictions are compared with the flight data, and a very good agreement in aerodynamic force and moment coefficients is observed between the CFD solutions and the reconstructed flight data.

Supersonic Flight Dynamics Test↗

NASA NTRS2017

Data Reduction Pipeline for the CHARIS Integral-Field Spectrograph I: Detector Readout Calibration and Data Cube Extraction

We present the data reduction pipeline for CHARIS, a high-contrast integral-field spectrograph for the Subaru Telescope. The pipeline constructs a ramp from the raw reads using the measured nonlinear pixel response and reconstructs the data cube using one of three extraction algorithms: aperture photometry, optimal extraction, or chi-squared fitting. We measure and apply both a detector flatfield and a lenslet flatfield and reconstruct the wavelength- and position-dependent lenslet point-spread function (PSF) from images taken with a tunable laser. We use these measured PSFs to implement a chi-squared-based extraction of the data cube, with typical residuals of approximately 5 percent due to imperfect models of the under-sampled lenslet PSFs. The full two-dimensional residual of the chi-squared extraction allows us to model and remove correlated read noise, dramatically improving CHARIS's performance. The chi-squared extraction produces a data cube that has been deconvolved with the line-spread function and never performs any interpolations of either the data or the individual lenslet spectra. The extracted data cube also includes uncertainties for each spatial and spectral measurement. CHARIS's software is parallelized, written in Python and Cython, and freely available on github with a separate documentation page. Astrometric and spectrophotometric calibrations of the data cubes and PSF subtraction will be treated in a forthcoming paper.

Brandt, Timothy D.↗

NASA NTRS1989

Kalman estimation for SEDS measurements

The first on-orbit experiment of the Small Expendable Deployer System (SEDS) for tethered satellites will collect telemetry data for tethered length, rate of deployment, and tether tension. The post-flight analysis will use this data to reconstruct the deployment history and determine payload position and tether shape. Two Kalman estimator algorithms were written, and output using simulated measurement data was compared. Both estimators exhibited the same estimated state histories, indicating that numerical instability in the traditional algorithm was not the cause of filter divergence. Estimation of acceleration biases was added, which reduced the error but did not correct the divergence. An add-a-bead estimator that adds lumped masses as the tether is deployed was written, which provides a state model that matches the BEADSIM simulation providing the true measurements and states. This twenty-one bead estimator produced state histories similar to those of the two-bead estimator, indicating that the filter divergence was not caused by a reduced-order model. The noise models used to date are relatively simple and may be the source of estimator divergence. The investigation of colored noise models, cross-correlated measurement and process covariances, and noise-adaptive filter techniques is recommended.

Carrington, Connie K.↗

NASA NTRS2013

High resolution wind measurements for offshore wind energy development

A method, apparatus, system, article of manufacture, and computer readable storage medium provide the ability to measure wind. Data at a first resolution (i.e., low resolution data) is collected by a satellite scatterometer. Thin slices of the data are determined. A collocation of the data slices are determined at each grid cell center to obtain ensembles of collocated data slices. Each ensemble of collocated data slices is decomposed into a mean part and a fluctuating part. The data is reconstructed at a second resolution from the mean part and a residue of the fluctuating part. A wind measurement is determined from the data at the second resolution using a wind model function. A description of the wind measurement is output.

Nghiem, Son Van↗

NASA NTRS2009

Trajectory Reconstruction of the ST-9 Sounding Rocket Experiment Using IMU and Landmark Data

This paper presents trajectory reconstruction of the ST-9 sounding rocket experiment using the onboard IMU data and descent imagery. The raw IMU accelerometer measurements are first converted into inertial acceleration and then used in trajectory integration. The descent images are pre-processed using a map-matching algorithm and unique landmarks for each image are created. Using the converted IMU data and descent images, the result from dead-reckoning and the kinematic-fix approaches are first compared with the GPS measurements. Then, both the IMU data and landmarks are processed together using a batch least-squares filter and the position, velocity, stochastic acceleration, and camera orientation of each image are estimated. The reconstructed trajectory is compared with the GPS data and the corresponding formal uncertainties are presented. The result shows that IMU data and descent images processed with a batch filter algorithm provide the trajectory accuracy required for pin-point landing.

Park, Ryan S.↗

NASA NTRS1980

Geometric representation methods for multi-type self-defining remote sensing data sets

Efficient and convenient representation of remote sensing data is highly important for an effective utilization. The task of merging different data types is currently dealt with by treating each case as an individual problem. A description is provided of work which is carried out to standardize the multidata merging process. The basic concept of the new approach is that of the self-defining data set (SDDS). The creation of a standard is proposed. This standard would be such that data which may be of interest in a large number of earth resources remote sensing applications would be in a format which allows convenient and automatic merging. Attention is given to details regarding the multidata merging problem, a geometric description of multitype data sets, image reconstruction from track-type data, a data set generation system, and an example multitype data set.

Anuta, P. E.↗

NASA NTRS1985

Infrared Astronomical Satellite (IRAS) Catalogs and Atlases. Explanatory Supplement

The Infrared Astronomical Satellite (IRAS) mission is described. An overview of the mission, a description of the satellite and its telescope system, and a discussion of the mission design, requirements, and inflight modifications are given. Data reduction, flight tests, flux reconstruction and calibration, data processing, and the formats of the IRAS catalogs and atlases are also considered.

Beichman, C. A.↗

NASA NTRS1981

Total Hip Joint Replacement Biotelemetry System

The development of a biotelemetry system that is hermetically sealed within a total hip replacement implant is reported. The telemetry system transmits six channels of stress data to reconstruct the major forces acting on the neck of the prosthesis and uses an induction power coupling technique to eliminate the need for internal batteries. The activities associated with the telemetry microminiaturization, data recovery console, hardware fabrications, power induction systems, electrical and mechanical testing and hermetic sealing test results are discussed.

Boreham, J. F.↗

NASA NTRS1993

Grid-independent upwind scheme for multidimensional flow

Recent advances in the development of a grid-independent finite volume scheme for the Euler equations of gas dynamics are described. In the proposed method, flowfield gradient data are reconstructed locally (on a triangle) using five elementary planar waves, and an upwind numerical flux function for grid-oblique waves is developed to model the effect of the passage of these waves on the data in a cell. Numerical examples for several two-dimensional test problems are included. These results show high wave resolution and nearly monotone strong-wave transitions.

Parpia, Ijaz H.↗

NASA NTRS1982

Reconstruction of atmospheric pollutant concentrations from remote sensing data - An application of distributed parameter observer theory

The reconstruction of a concentration distribution from spatially averaged and noise-corrupted data is a central problem in processing atmospheric remote sensing data. Distributed parameter observer theory is used to develop reconstructibility conditions for distributed parameter systems having measurements typical of those in remote sensing. The relation of the reconstructibility condition to the stability of the distributed parameter observer is demonstrated. The theory is applied to a variety of remote sensing situations, and it is found that those in which concentrations are measured as a function of altitude satisfy the conditions of distributed state reconstructibility.

Koda, M.↗

NASA NTRS2008

Aerodynamics for the Mars Phoenix Entry Capsule

Pre-flight aerodynamics data for the Mars Phoenix entry capsule are presented. The aerodynamic coefficients were generated as a function of total angle-of-attack and either Knudsen number, velocity, or Mach number, depending on the flight regime. The database was constructed using continuum flowfield computations and data from the Mars Exploration Rover and Viking programs. Hypersonic and supersonic static coefficients were derived from Navier-Stokes solutions on a pre-flight design trajectory. High-altitude data (free-molecular and transitional regimes) and dynamic pitch damping characteristics were taken from Mars Exploration Rover analysis and testing. Transonic static coefficients from Viking wind tunnel tests were used for capsule aerodynamics under the parachute. Static instabilities were predicted at two points along the reference trajectory and were verified by reconstructed flight data. During the hypersonic instability, the capsule was predicted to trim at angles as high as 2.5 deg with an on-axis center-of-gravity. Trim angles were predicted for off-nominal pitching moment (4.2 deg peak) and a 5 mm off-axis center-ofgravity (4.8 deg peak). Finally, hypersonic static coefficient sensitivities to atmospheric density were predicted to be within uncertainty bounds.

Edquist, Karl T.↗