Search NASA⌕ Search

SEARCH · Search NASA

Results for “data tips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

LANDSAT instruments characterization

Work performed for the LANDSAT instrument characterization task in the areas of absolute radiometry, coherent noise analysis, and between-date smoothing is reported. Absolute radiometric calibration for LANDSAT-5 TM under ambient conditions was performed. The TM Radiometric Algorithms and Performance Program (TRAPP) was modified to create optional midscan data files and to match the TM Image Processing System (TIPS) algorithm for pulse determination. Several data reduction programs were developed, including a linear regression and its plotted result. A fast Fourier transformation study was conducted on the resequenced TM data. Subscenes of homogeneous water within scenes over Pensacola, Florida were used for testing the FFT on the resequenced data. Finally, a gain and pulse height stability study of LANDSAT 5 TM spectral bands was performed.

Lee, Y.↗

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗

Adaptive Error Estimation in Linearized Ocean General Circulation Models

Data assimilation methods are routinely used in oceanography. The statistics of the model and measurement errors need to be specified a priori. This study addresses the problem of estimating model and measurement error statistics from observations. We start by testing innovation based methods of adaptive error estimation with low-dimensional models in the North Pacific (5-60 deg N, 132-252 deg E) to TOPEX/POSEIDON (TIP) sea level anomaly data, acoustic tomography data from the ATOC project, and the MIT General Circulation Model (GCM). A reduced state linear model that describes large scale internal (baroclinic) error dynamics is used. The methods are shown to be sensitive to the initial guess for the error statistics and the type of observations. A new off-line approach is developed, the covariance matching approach (CMA), where covariance matrices of model-data residuals are "matched" to their theoretical expectations using familiar least squares methods. This method uses observations directly instead of the innovations sequence and is shown to be related to the MT method and the method of Fu et al. (1993). Twin experiments using the same linearized MIT GCM suggest that altimetric data are ill-suited to the estimation of internal GCM errors, but that such estimates can in theory be obtained using acoustic data. The CMA is then applied to T/P sea level anomaly data and a linearization of a global GFDL GCM which uses two vertical modes. We show that the CMA method can be used with a global model and a global data set, and that the estimates of the error statistics are robust. We show that the fraction of the GCM-T/P residual variance explained by the model error is larger than that derived in Fukumori et al.(1999) with the method of Fu et al.(1993). Most of the model error is explained by the barotropic mode. However, we find that impact of the change in the error statistics on the data assimilation estimates is very small. This is explained by the large representation error, i.e. the dominance of the mesoscale eddies in the T/P signal, which are not part of the 21 by 1" GCM. Therefore, the impact of the observations on the assimilation is very small even after the adjustment of the error statistics. This work demonstrates that simult&neous estimation of the model and measurement error statistics for data assimilation with global ocean data sets and linearized GCMs is possible. However, the error covariance estimation problem is in general highly underdetermined, much more so than the state estimation problem. In other words there exist a very large number of statistical models that can be made consistent with the available data. Therefore, methods for obtaining quantitative error estimates, powerful though they may be, cannot replace physical insight. Used in the right context, as a tool for guiding the choice of a small number of model error parameters, covariance matching can be a useful addition to the repertory of tools available to oceanographers.

Chechelnitsky, Michael Y.↗

Study of blade clearance effects on centrifugal pumps

A program of analysis, design, fabrication, and testing has been conducted to develop and experimentally verify analytical models to predict the effects of impeller blade clearance on centrifugal pumps. The effect of tip clearance on pump efficiency, and the relationship between the head coefficient and torque loss with tip clearance was established. Analysis were performed to determine the cost variation in design, manufacture, and test that would occur between unshrouded and shrouded impellers. An impeller, representative of typical rocket engine impellers, was modified by removing its front shroud to permit variation of its blade clearances. It was tested in water with special instrumentation to provide measurements of blade surface pressures during operation. Pump performance data were obtained from tests at various impeller tip clearances. Blade pressure data were obtained at the nominal tip clearance. Comparisons of predicted and measured data are given.

Hoshide, R. K.↗

Acoustical effects of blade tip shape changes on a full scale helicopter rotor in a wind tunnel

Four tip shapes were tested. They were rectangular, swept, tapered, and swept-tapered. The measured data covered a wide range of operating conditions. The range of advancing tip Mach numbers were between 0.72 to 0.96, and the advance ratios were from 0.2 to 0.375. At low and moderate advancing tip Mach number, the data in the dbA scale appear to indicate the swept tip is the quietest, swept tapered the second, tapered third and rectangular the most noisy. Above an advancing tip Mach number of about 0.89, a distinct acoustical pulse can be observed, which dominates the acoustical waveform. The pulse shape is symmetric at moderate tip Mach number, changing to a sawtooth shape at high advancing tip Mach numbers. Based on the amplitude of the impulsive noise, it appears the swept-tapered tip is the quietest, tapered tip the second, swept tip third and square tip the most noisy. The data presented in this report should be useful as data bases for modeling and evaluating helicopter impulsive noise.

Lee, A.↗

Disorder to Order in Interface Patterns: Thermal Noise to Limit Cycle Transition in Dendrite Sidebranch Formation

Thin sample directional solidification experiments have been carried out in the model succinonitrile-camphor system to examine the origin of secondary branches in dendrite morphologies. Thermal noise at the dendrite tip creates interface instabilities which amplify to form sidebranches. This is accepted as the primary mode of sidebranching in dendritic growth from an undercooled melt and occurs in directional solidification of dendrites. The proposed limit cycle couples the growth of the tip with the initiation of the sidebranch. Directional solidification of curved interfaces is a driven dissipative system with the potential to form a limit cycle. Two sets of experiments were performed, the first holding velocity constant and evolving the gradient and the second imposing oscillating velocities around the natural period of sidebranching. Both experimental methods were found to characterize a transition from disordered sidebranching induced by thermal noise to ordered sidebranching produced by the limit cycle mechanisms. This is the first quantitative measurement of previously hypothesized limit cycle growth. These experiment sets have been quantitatively analyzed for dynamic behavior seen in limit cycles. High-quality data sets of the tip and instability enable the measurement of the FFT and analysis through a power spectrum. At low gradients, the sidebranches are found to be excited by thermal noise far away from the tip. As the gradient increases and velocity is held constant, the distance between the instability and tip decreases until limit cycle growth is found between the tip of the primary dendrite and the first forming sidebranch. An alternative to the deterministic limit cycles seen in experiments of gradient evolution is a limit cycle actively driven through the square wave oscillation of velocity. Crucial observations of the solidified microstructure conclude that this produced periodic interconnected bridges between the primary dendrites. This is a finding with potentially significant implications for commercial applications.

Trevor Lyons↗

Pioneer Venus Sounder Probe Neutral Gas Mass Spectrometer

A neutral gas mass spectrometer was flown to Venus as part of the Pioneer Venus Multiprobe to measure the composition of its lower atmosphere. The instrument, mounted in the Sounder Probe, was activated after the probe entered the top of the atmosphere, and it obtained data during the descent from 62 km to the surface. Atmospheric gases were sampled through a pair of microleaks, the effluent from which was pumped by a combination of ion and getter pumping. A pneumatically operated valve, controlled by the ambient atmospheric pressure, maintained the ion source pressure at a nearly constant value during descent while the atmospheric pressure varied by three orders of magnitude. A single focusing magnetic sector field mass spectrometer with mass resolution sufficient to reasonably separate argon from C3H4 at 40 amu provided the mass analysis and relative abundance measurements. A microprocessor controlled the operation of the mass spectrometer through a highly efficient peak-tip stepping routine and data compression algorithm that effected a scan of the mass spectrum from 1 to 208 amu in 64 sec while requiring an information rate of only 40 bits/sec to return the data to earth. A subscale height altitude resolution was thus obtained. Weight, size, and power requirements were minimized to be consistent with interplanetary flight contraints.

Hoffman, J. H.↗

High-loading low-speed fan study. 4: Data and performance with redesign stator and including a rotor tip casing treatment

A single stage fan with a rotor tip speed of 1000 ft/sec(304.8 m/sec) and a hub-to-tip ratio of 0.392 was retested with a redesigned stator. Tests were conducted with uniform inlet, tip-radial, hub-radial, and circumferential inlet distortions. With uniform inlet flow, stall margin was improved 12 percentage points above that with the original stator. The fan demonstrated an efficiency of 0.883 and a stall margin of 15 percent at a pressure ratio of 1.488 and a specific flow of 41.17 lb/sec/sq ft. Tests were also made with a redesigned casing treatment consisting of skewed slots over the rotor blade tips. This casing treatment gave a 7 percentage point improvement in stall margin when tested with tip radial distortion (when the rotor tip initiated stall). Noise measurements at the fan inlet and exit indicate no effect from closing the stator 10 degrees, nor were there measurable effects from adding skewed slots over the blade tips.

Harley, K. G.↗

Effect of casing treatment on performance of a multistage compressor

AJ85-GE-13 engine was equipped with a compressor case which allowed changes to the case wall over the rotor tips of six of its stages. The engine was tested with four inlet configurations: undistorted and with 180 deg circumferential, hub radial, and tip radial distortions. Baseline data defining compressor performance and stall regions were taken for these inlet configurations with solid (untreated) compressor case inserts. Circumferentially grooved inserts were installed in the first three and last three stages, and the compressor was mapped under similar conditions. The compressor was mapped a third time with untreated inserts in the first three stages and inserts having slots conforming to blade angles in the last three stages. In most cases, the stall pressure ratio was the same as or lower than the baseline. Pumping capacity with the slotted inserts was reduced. Overall compressor efficiency with the grooved rings installed did not appreciably differ from the baseline, but it was 1 to 2 percentage points lower than the baseline with the slotted rings in place. Average stage characteristics for the undistorted inlet case showed little or no sensitivity to casing treatment.

Wenzel, L. M.↗

Longitudinal aerodynamic characteristics at Mach numbers from 1.60 to 2.86 for a fixed-span missile with three wing planforms

Effects of wing planform modifications on the longitudinal aerodynamic characteristics of a fixed span, maneuverable cruciform missile configuration were determined. A basic delta planform and two alternate trapezoidal planforms having progressively increasing tip chords were included. Data were obtained for angles of attack up to approximately -32 deg, model roll angles of 0 deg to 45 deg, and tail control deflections of 0 deg and -20 deg. The experimental drag due to lift was compared with linear values.

Spearman, M. L.↗

An experimental investigation of the effect of rotor tip shape on helicopter blade-slap noise

The effect of tip-shape modification on blade-vortex interaction-induced helicopter blade-slap noise was investigated. The general rotor model system (GRMS) with a 3.148 m (10.33 ft) diameter, four-bladed fully articulated rotor was installed in the Langley V/STOL wind tunnel. The tunnel was operated in the open-throat configuration with treatment to improve the semi-anechoic characteristics of the test chamber. Based on previous investigation, four promising tips (ogee, sub-wing, 60 deg swept-tapered, and end-plate) were used along with a standard square tip as a baseline configuration. Aerodynamic and acoustical data concerning the relative applicability of the various tip configurations for blade-slap noise reduction are presented without analysis or discussion.

Hoad, D. R.↗

A flight investigation of performance and loads for a helicopter with RC-SC2 main-rotor blade sections

The test envelope included hover, forward-flight speed sweeps from 33 to 74 m/sec (65 to 144 knots), and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point describes vehicle flight states, control positions, rotor loads, power requirements and blade motions. Rotor loads were reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗

LANDSAT 4 investigations of Thematic Mapper and Multispectral Scanner applications

Interband detector noise was suppressed in the TIPS TM North Dakota data by median filtering. Procedures were developed to optimize the visual information content of thematic mapper data and evaluate the resulting photographic products by visual interpretation. A digital to analog TM transfer function was developed which properly placed the digital values on the most useable portion of film response curve. Utilizing the calculated minimum, mean, and maximum and the respective standard deviations of the bands from 50 sample scenes of TM data, look up tables were designed which resulted in acceptable photographic products. These products were evaluated by generation of color composites of selected band combinations using standard photo production procedures, and visual interpretation of scene features.

Lauer, D. T.↗

Effect of advanced rotorcraft airfoil sections on the hover performance of a small-scale rotor model

A hover test was conducted on a small scale rotor model for two sets of tapered rotor blades. The baseline rotor blade set used a NACA 0012 airfoil section, whereas the second rotor blade set had advanced rotorcraft airfoils distributed along the radius. The experiment was conducted for a range of thrust coefficients and tip speeds, and the data were compared to the predictions of three analytical methods. The data show the advantage of the advanced airfoils at the higher rotor thrust levels; two of the analyses predicted the correct data trends.

Althoff, Susan L.↗

A method for determining crack opening load from load-displacement data

The fatigue crack opening load is determined as the tangent point on the ascending load-displacement data between the curved portion and the upper linear region. A model for the 'unzipping' behavior of the crack indicates that the curved portion of the load-deflection curve is second order. The opening load is determined by a nonlinear, least squares fit of the data to the model, which optimally locates the tangent point of the two curves. The method provided consistent results for determining opening load P(op) for 7475-T731 aluminum using data from a crack tip opening gage.

Carman, C. Davis↗

Determining the Molecular Growth Mechanisms of Tetragonal Lysozyme Crystals

Studies of the growth of tetragonal lysozyme crystals employing atomic force microscopy (AFM) have shown the advantages of this technique in investigating the growth mechanisms of protein crystals [1]. The resolution of these studies was in the micron range, which revealed surface features such as the occurrence of dislocations and 2D nucleation islands, similar to those found in inorganic systems. They clearly showed that the crystals grew by these surface growth mechanisms. However, the studies also revealed some surprising features, such as bimolecular growth step heights and pronounced growth anisotropies on the (110) face, which could not be explained. In previous studies we employed Periodic Bond Chain (PBC) theory to tetragonal lysozyme crystal growth and found that the crystals were constructed by strongly bonded molecular chains forming helices about the 43 axes [2,3]. The helices were connected to each other with weaker bonds. The growth process was shown to proceed by the formation of these 43 helices, resulting in bimolecular growth steps on the (110) face. It was also shown to explain many other observations on tetragonal lysozyme crystal growth. Although PBC analysis is not a new technique [4], it has not been widely used as the mechanisms predicted from it could not be experimentally verified. In this study the growth process of these crystals was investigated, particularly for the (110) face, employing some newly developed high resolution AFM techniques. These techniques allowed individual lysozyme molecules on the crystal faces to be resolved and predictions from PBC analyses to be tested. The analyses had shown that of the two possible packing arrangements on (110) faces, only one would actually occur. Employing the first of the newly developed techniques, these faces were scanned by high resolution AFM. The resulting images were then compared with the theoretically constructed images for the two possible packing arrangements on the (110) face. The theoretical images were constructed by convolution of the crystal surface shape obtained from crystallographic data with the AFM tip shape. The comparison confirmed the prediction that the molecular packing arrangement of these faces corresponded to that for complete 43 helices. The second AFM technique that was developed was used to follow the growth process by measuring the dimensions of individual growth units on the (110) face. Linescans across a growth step, performed near the saturation limit of the crystals, allowed the growth unit dimensions to be measured. These measurements showed that growth on the (110) face proceeded by the formation of new 43 helices from the addition of at least tetramer units in the [110] direction. In the [001] direction growth proceeded by the addition of various aggregate units corresponding to the 4(sub 3) helices.

Li, Huayu↗

Acoustic Characteristics of a Model Isolated Tiltrotor in DNW

An aeroacoustic wind tunnel test was conducted using a scaled isolated tiltrotor model. Acoustic data were acquired using an in-flow microphone wing traversed beneath the model to map the directivity of the near-field acoustic radiation of the rotor for a parametric variation of rotor angle-of-attack, tunnel speed, and rotor thrust. Acoustic metric data were examined to show trends of impulsive noise for the parametric variations. BVISPL maximum noise levels were found to increase with mu for constant alpha and C(sub T), although the maximum BVI levels were found at much higher cc than for a typical helicopter. BVISPL levels were found to increase with mu for constant alpha and C(sub T). BVISPL was found to decrease with increasing C(sub T) for constant alpha and mu, although BVISPL increased with thrust for a constant wake geometry. Metric data were also scaled for M,i, to evaluate how well simple power law scaling could be used to correct metric data for M(sub tip) effects.

Booth, Earl R., Jr.↗