Results for “delamination damage” — Page 6

NASA NTRS2017

Simulated Space Environment Effects on a Candidate Solar Sail Material

For long duration missions of solar sails, the sail material needs to survive harsh space environments and the degradation of the sail material controls operational lifetime. Therefore, understanding the effects of the space environment on the sail membrane is essential for mission success. In this study, we investigated the effect of simulated space environment effects of ionizing radiation, thermal aging and simulated potential damage on mechanical, thermal and optical properties of a commercial off the shelf (COTS) polyester solar sail membrane to assess the degradation mechanisms on a feasible solar sail. The solar sail membrane was exposed to high energy electrons (about 70 keV and 10 nA/cm2), and the physical properties were characterized. After about 8.3 Grad dose, the tensile modulus, tensile strength and failure strain of the sail membrane decreased by about 20 ~ 95%. The aluminum reflective layer was damaged and partially delaminated but it did not show any significant change in solar absorbance or thermal emittance. The effect on mechanical properties of a pre-cracked sample, simulating potential impact damage of the sail membrane, as well as thermal aging effects on metallized PEN (polyethylene naphthalate) film will be discussed.

Kang, Jin Ho↗

NASA NTRS1990

Progression of damage and fracture in composites under dynamic loading

A new computational simulation method is presented to evaluate the dynamic aspects of composite structural response and durability that could not be simulated previously. Composite structural behavior under any loading, geometry, composite system, laminate configuration, and boundary conditions can now be simulated. Structural degradation, delamination, fracture, and damage propagation are included in the simulation. An angle-plied composite plate structure under normal impact loading is used as an example to demonstrate the versatility of the simulation method.

Minnetyan, Levon↗

NASA NTRS1990

Progression of damage and fracture in composites under dynamic loading

A new computational simulation method is presented to evaluate the dynamic aspects of composite structural response and durability that have not been simulated previously. Composite structural behavior under any loading condition, geometry, composite system, laminate configuration, and boundary conditions can now be simulated. Structural degradation, delamination, fracture, and damage propagation are included in the simulation. An angle-plied composite plate structure under normal impact loading is used as an example to demonstrate the versatility of the simulation method.

Minnetyan, Levon↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗

NASA NTRS2023

The Effect of Oxidation in Environmental Barrier Coatings Subject to Foreign Object Damage

Oxidation and foreign object damage (FOD) are two key failure modes for environmental barrier coatings (EBCs). For EBCs with a silicon (Si) bond coat, a thermally grown oxide (TGO) layer forms at the EBC –bond coat interface. The TGO layer is considered the weak interface, and directly influences the life of the EBC. Moreover, FOD has been shown to cause significant subsurface damage resulting in delamination or spallation of the EBC which can occur at the EBC -bond coat interface or the bond coat -substrate interface. The purpose of this work is to investigate the synergistic effects of oxidation and FOD in a ytterbium disilicate (𝑌𝑏2𝑆𝑖2𝑂7) EBC. FOD testing is conducted on as-deposited and steam oxidized samples at room temperature using a 1.59-mm hardened steel ball projectile. The resulting damage is characterized by optical profilometry and scanning electron microscopy (SEM). Additionally, a quasi-static, mechanical assessment of the EBC bond strength in the presence of a growing TGO is presented.

environmental barrier coatings (EBCs)↗

NASA NTRS2023

Characterization of Low-Velocity Impact Damage in Thermoplastic Laminated Composites

The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.

Composite Materials↗

NASA NTRS2023

Characterization of Low-Velocity Impact Damage in Thermoplastic Laminated Composites

The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.

Composite Materials↗

NASA NTRS1997

Fatigue Debonding Characterization in Composite Skin/Stringer Configurations

The objective of this work was to investigate the fatigue damage mechanisms and to identify the influence of skin stacking sequence in carbon epoxy composite bonded skin/stringer constructions. A simple 4-point-bending test fixture originally designed for previously performed monotonic tests was used to evaluate the fatigue debonding mechanisms between the skin and the bonded frame when the dominant loading in the skin is flexure along the edge of the frame. The specimens consisted of a tapered flange, representing the stringer, bonded onto a skin. Based on the results of previous monotonic tests two different skin lay-ups in combination with one flange lay-up were investigated. The tests were performed at load levels corresponding to 40%, 50%, 60%, 70%, and 80% of the monotonic fracture loads. Microscopic investigations of the specimen edges were used to document the onset of matrix cracking and delamination, and subsequent fatigue delamination growth. Typical damage patterns for both specimen configurations were identified. The observations showed that failure initiated near the tip of the flange in the form of matrix cracks at one of two locations, one in the skin and one in the flange. The location of the 90 deg flange and skin plies relative to the bondline was identified as the dominant lay-up feature that controlled the location and onset of matrix cracking and subsequent delamination. The fatigue delamination growth experiments yielded matrix cracking and delamination onset as a function of fatigue cycles as well as delamination length as a function of the number of cycles.

Cvitkovich, Michael K.↗

NASA NTRS1992

Analysis of composite structures with delaminations under combined bending and compression

A methodology had been developed for strength prediction of composite structures with delaminations under combined bending and compression loads. The methodology is an extension of the delamination analysis method developed under the USAF/Boeing/Northrop 'Damage Tolerance of Composites' program. Delamination buckling and strain energy release rate analyses are used as basic tools in the strength prediction. In addition, failure mode interaction and structural configuration effects are considered. The influence of fasteners on the strength of a delaminated structure is incorporated to evaluate assembly-caused delaminations. The capabilities and limitations of the analysis method are shown by correlating the analytical results with the existing experimental data. The failure load, failure mode and failure sequence of a structure containing delaminations are predicted and the analytical results are compared with test data.

Kan, Han-Pin↗

NASA NTRS2000

Resin Film Infusion (RFI) Process Modeling for Large Transport Aircraft Wing Structures

Resin film infusion (RFI) is a cost-effective method for fabricating stiffened aircraft wing structures. The RFI process lends itself to the use of near net shape textile preforms manufactured through a variety of automated textile processes such as knitting and braiding. Often, these advanced fiber architecture preforms have through-the-thickness stitching for improved damage tolerance and delamination resistance. The challenge presently facing RFI is to refine the process to ensure complete infiltration and cure of a geometrically complex shape preform with the high fiber volume fraction needed for structural applications. An accurate measurement of preform permeability is critical for successful modeling of the RFI resin infiltration process. Small changes in the permeability can result in very different infiltration behavior and times. Therefore, it is important to accurately measure the permeabilities of the textile preforms used in the RFI process. The objective of this investigation was to develop test methods that can be used to measure the compaction behavior and permeabilities of high fiber volume fraction, advanced fiber architecture textile preforms. These preforms are often highly compacted due to through-the-thickness stitching used to improve damage tolerance. Test fixtures were designed and fabricated and used to measure both transverse and in-plane permeabilities. The fixtures were used to measure the permeabilities of multiaxial warp knit and triaxial braided preforms at fiber volume fractions from 55% to 65%. In addition, the effects of stitching characteristics, thickness, and batch variability on permeability and compaction behavior were investigated.

Knott, Tamara W.↗

NASA NTRS1988

Thermo-viscoelastic analysis of composite materials, volume 1

Advanced composite materials, especially graphite/epoxy, are being applied to aircraft structures in order to improve performance and save weight. An important consideration in composite design is the residual strength of a structure containing holes, delaminations, or interlaminar damage when subjected to compressive loads. Recent studies have revealed the importance of viscoelastic effects in polymer-based composites. The viscoelastic effect is particularly significant at elevated temperature/moisture conditions since the matrix material is strongly affected by the environment. The solution of viscoelastic problems in composites was limited to special cases which can be solved by classical lamination theory. A finite element procedure is presented for calculating time-dependent stresses and strains in composite structures with general configurations and complicated boundary conditions. Using this procedure the in-plane and interlaminar stress distributions and histories in notched and unnotched composites were obtained for mechanical and thermal loads. Both two-dimensional and three-dimensional viscoelastic problems are analyzed. The effects of layup orientation and load spectrum on creep response and stress relaxation were also studied.

Lin, K. Y.↗

NASA NTRS1997

Trans-Laminar-Reinforced (TLR) Composites

A Trans-Laminar-Reinforced (TLR) composite is defined as composite laminate with up to five percent volume of fibrous reinforcement oriented in a 'trans-laminar' fashion in the through-thickness direction. The TLR can be continuous threads as in 'stitched laminates', or it can be discontinuous rods or pins as in 'Z-Fiber(TM) materials. It has been repeatedly documented in the literature that adding TLR to an otherwise two dimensional laminate results in the following advantages: substantially improved compression-after-impact response; considerably increased fracture toughness in mode 1 (double cantilever beam) and mode 2 (end notch flexure); and severely restricted size and growth of impact damage and edge delamination. TLR has also been used to eliminate catastrophic stiffener disbonding in stiffened structures. TLR directly supports the 'Achilles heel' of laminated composites, that is delamination. As little as one percent volume of TLR significantly alters the mechanical response of laminates. The objective of this work was to characterize the effects of TLR on the in-plane and inter-laminar mechanical response of undamaged composite laminates. Detailed finite element models of 'unit cells', or representative volumes, were used to study the effects of adding TLR on the elastic constants; the in-plane strength; and the initiation of delamination. Parameters investigated included TLR material, TLR volume fraction, TLR diameter, TLR through-thickness angle, ply stacking sequence, and the microstructural features of pure resin regions and curved in-plane fibers. The work was limited to the linear response of undamaged material with at least one ply interface. An inter-laminar dominated problem of practical interest, a flanged skin in bending, was also modeled.

Hinders, Mark↗

NASA NTRS2003

Numerical Modeling, Thermomechanical Testing, and NDE Procedures for Prediction of Microcracking Induced Permeability of Cryogenic Composites

Reusable Space Vehicles will include light cryogenic composite fuel tanks that must not leak excessively even after multiple launches. Damage in cryogenic composite fuel tanks induced during manufacturing and advanced by thermomechanical cycling can accelerate leakage of the propellant. Whether the leakage exceeds tolerable levels depends on many factors, including pressure gradients, microcrack density, other damage such as delamination, connectivity of the cracks, residual stresses from manufacture, service-induced stresses from thermal and mechanical loads, and composite lay-up. Although it is critical to experimentally characterize permeability during various thermal and mechanical load histories, optimal design depends on having analytical models that can predict the effect of various parameters on performance. Our broad goal is to develop such models that are experimentally validated by destructive and non-destructive evaluation means.

Noh, Jae↗

NASA NTRS2009

Application of Air Coupled Acoustic Thermography (ACAT) for Inspection of Honeycomb Sandwich Structures

The application of a noncontact air coupled acoustic heating technique is investigated for the inspection of advanced honeycomb composite structures. A weakness in the out of plane stiffness of the structure, caused by a delamination or core damage, allows for the coupling of acoustic energy and thus this area will have a higher temperature than the surrounding area. Air coupled acoustic thermography (ACAT) measurements were made on composite sandwich structures with damage and were compared to conventional flash thermography. A vibrating plate model is presented to predict the optimal acoustic source frequency. Improvements to the measurement technique are also discussed.

Winfree, William P.↗

NASA NTRS2019

Experimental and Numerical Analysis of Skin-Stiffener Separation Using a Seven-Point Bend Configuration

Skin-stiffener separation in stiffened composite panels consists of a complex interaction between multiple scales of progressive damage and failure mechanisms. This work used a superposed cohesive element method of modeling resistance curve effects that represents the structural interface of a unidirectional tape skin and a fabric stiffener. Finite element models using cohesive elements with input properties obtained from tape-to-fabric interface characterization tests were compared to experimental results of a stable skin-stiffener separation characterization test using a seven-point bend fixture. This fixture deformed the stiffened panel specimens into a buckled configuration which induced mixed-mode interlaminar stress states at the skin-stiffener interface. The advantage of this fixture was the potential for more stable damage initiation and delamination growth compared to a stringer-stiffened panel under axial compression. Use of the superposed cohesive elements showed promise, but the characterization of interface material properties as input to the cohesive elements remains a crucial component to be investigated to ensure accurate prediction of skin-stiffener separation.

Kosztowny, Cyrus J. R.↗

NASA NTRSDate not supplied

The PCM is Dead! Long Live O-PCM!

The ability to reconfigure the optical behavior of a device enables free-space applications ranging from imaging to sensing and signal control. Such optical devices can be compacted via meta-surfaces, patterned structures with feature sizes below the incident wavelength. Leveraging geometry in addition to material properties and CMOS fabrication techniques has allowed meta-surfaces for lenses, holograms, beam steerers and more. To incorporate multiple optical functions into one device, various methods of device control have been implemented, such as stretching of flexible substrates, tuning the refractive index of the comprising meta-atoms via the electro-optic or the thermo-optic effects, phase transition materials such as VO2 and more. Chalcogenide glasses used as optical phase change materials, such as Ge¬2Sb2Te5 (GST), have gained increased traction in the optics community for potential use in the near infrared (NIR) and mid infrared (MIR) bands, including the telecom bands. Various chalcogenides such as Sb2Se3, Sb2S3, Ge2Sb¬2Se5 and Ge2Sb2Se4Te (GSST) have been investigated due to their broad NIR or MIR transparency window and large changes in refractive index. In their amorphous phase, these materials usually display a lower refractive index and low absorption when compared to their crystalline state which display a higher refractive index and typically larger extinction coefficients. The amorphous-crystalline reversible switching can be done via fast melt-quenching thermal processes triggered by laser or electrical impulses, relying on a substrate as a heat sink. The potential of PCMs in photonic devices can be limited by intrinsic material limitations as well as by device fabrication issues. To explore the cyclability of GSST, a PCM with large refractive index contrast and on-chip electrothermal switching on a silicon-on-insulator platform has been done to analyze potential failure mechanisms from both a material and device perspective. A brief outline of the instrumentation and phase change contrast analysis is provided. Dewetting of the PCM, delamination of and damage in the PECVD SiNx protective layer, elemental migration in the PCM and optical contrast decay have been observed in cycled GSST devices. Guidelines for device performance improvement are proposed, and an improved design with larger endurance is shown in progress.

reconfigurable photonics↗

NASA NTRS1991

Progressive failure methodologies for predicting residual strength and life of laminated composites

Two progressive failure methodologies currently under development by the Mechanics of Materials Branch at NASA Langley Research Center are discussed. The damage tolerance/fail safety methodology developed by O'Brien is an engineering approach to ensuring adequate durability and damage tolerance by treating only delamination onset and the subsequent delamination accumulation through the laminate thickness. The continuum damage model developed by Allen and Harris employs continuum damage laws to predict laminate strength and life. The philosophy, mechanics framework, and current implementation status of each methodology are presented.

Harris, Charles E.↗