Search NASA⌕ Search

SEARCH · Search NASA

Results for “discharge current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

First lower hybrid current drive experiments on the WEST tokamak

The first lower hybrid current drive experiments in the full tungsten WEST tokamak are reported. Good wave coupling is found at rather low plasma current (q 95 ~4.3) and medium density (n e ~3×10 19 m -3 ). Reflection coefficient is in agreement with the expectation from the linear theory of coupling. With low reflection coefficients, 5MW was coupled for 2 seconds. High central electron temperature, up to 5keV, is achieved at ne = 3-4×10 19 m -3 . Flat and even hollow profiles of tungsten density are derived from the bolometry diagnostic. The stored thermal energy follows the H96-P scaling law with very slight degradation with density. The current drive efficiency has been assessed in low loop voltage (V L ~0.15V) discharges. Low plasma current operation and rather high effective charge (Z eff ~3) lead to modest current drive efficiency (η = 0.5-0.65 × 10 19 A.W -1 m -2 ). Long pulse operation (~30s) with high LHCD power (P LH =2.7MW) is achieved with stationary parameters, in particular electron and impurity densities, with the upper water-cooled tungsten divertor.

Goniche, M.↗
DOE OSTI2020

DEMONSTRATION OF MULTI-PHYSICS EVALUATION OF FUEL ROD BURST PROBABILITY WITH BURNUP EXTENSION UNDER LBLOCA CONDITIONS

Extending the fuel discharge burnup level, e.g., from the current limit of rod averaged discharge burnup limit of 62 GWD/MT to a proposed new limit of 75 GWD/MT, can provide significant economic benefits to the current fleet of operating light water reactors (LWRs). It allows for longer operating cycles and improved resource utilization. The major economic gain of longer operating cycles is attributable to the increased capacity factor resulting from decreased refueling time as a fraction of total operating time, as well as fewer assemblies to be discharged for a given amount of energy produced. The main licensing challenges for higher burnup fuel are to ensure fuel rod safety under design basis accident conditions, especially under large-break loss-of-coolant accident (LBLOCA) and reactivity insertion accident (RIA). In this work, two-year cycle core design for a typical 4-loop pressurized water reactor (PWR) is performed with enrichment increased up to 6% and burnup extended to 75 GWD/MT. The fuel rod burst potential evaluations under large-break loss-of-coolant accident (LBLOCA) conditions are subsequently performed using the multi-physics best estimate plus uncertainty analysis framework LOTUS (LOCA Toolkit for the U.S. LWRs) and the preliminary results are presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Reconstruction of current profiles from external magnetic and MSE measurements on DIII-D

This work introduces a new current model into the EFIT code for plasma current profile reconstruction. Using this model, edge-localized current density profiles are reconstructed solely from external magnetic measurements. Quantitative comparisons show that edge current profiles obtained with the new current model align closely with those from kinetic equilibrium reconstruction. The new model enables current density reconstruction with fewer diagnostics than kinetic equilibrium reconstruction (Lao et al 1990 Nucl. Fusion 30 1035–49), demonstrating that edge-localized current density information can be obtained from external magnetic measurements only, without the help of kinetic profiles and internal diagnostics, and without using the bootstrap current model. Furthermore, with the constraints of external magnetic and MSE measurements, current profiles in full radius obtained from the new model are in good agreement with the results of kinetic equilibrium reconstruction, which not only improves the efficiency of current reconstruction but also helps avoid possible errors caused by different kinds of diagnoses. Possible applications are also discussed, and a brief analysis of the evolution of the full-radius current density is performed. Noticeable decreases in both the magnitude and gradient of the edge current around the time of ELM bursts are observed. Moreover, analysis of the full radius current density profiles ( ρ N = 0 − 1.0, ρN denotes to square root of the normalized toroidal flux) reveals that as the edge current changes, the inner current also changes following a sinusoidal-like pattern at almost all time slices during four type-I ELMs in discharge 161493. The current evolution in the inner region ( ρ N = 0.2 − 0.6) is synchronized with the boundary region ( ρ N = 0.89 − 1.0), while the intermediate region ( ρ N = 0.6 − 0.89) shows opposite behavior. This sinusoidal-like variations in full-radius current density profile indicates strong core-pedestal coupling, suggesting ELMs significantly affect core plasmas, though current changes manifest differently across radial regions.

EFIT↗
DOE OSTI2021

Impact of Electrode Thickness and Temperature on the Rate Capability of Li 4 Ti 5 O 12 /LiMn 2 O 4 Cells

Growing demand for stationary energy storage systems requires the development of low cost, long cycle life, safe batteries. Lithium-ion batteries (LiBs) utilizing Li 4 Ti 5 O 12 /LiMn 2 O 4 (LMO) cathode are promising candidates providing critical-material-free chemistry, high power capability, and long lifespan. However, their low energy density is a major drawback. In this work, we evaluate the rate performance of LTO/LMO cells fabricated with electrode loadings from 1.7 to 4.2 mAh cm -2 toward the development of high energy density and low cost LTO/LMO cells. The operating temperature is varied from 30 °C to 55 °C to evaluate the impact of electrode thickness vs temperature limitations on the electrode utilization. In addition, Newman modeling is performed to provide detailed understandings of the cell performance. Combining experimental and simulated results, we show the rate capability of the thicker electrodes is limited by the electrolyte transport. When the cells are discharged by applying pulsed current, Li + ion depletion is mitigated and the discharge capacity increases. Thus, high energy density LTO/LMO cells for BTMS applications can operate more efficiently when intermittent rest is applied. Finally, overcoming electrolyte transport limitations will be the key to enabling the development of high energy density LTO/LMO cells using thick electrodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Evaluating ZEBRA Battery Module under the Peak-Shaving Duty Cycles

With the recent rapid increase in demand for reliable, long-cycle life, and safe battery technologies for large-scale energy-storage applications, a battery module based on ZEBRA battery chemistry is extensively evaluated for its application in peak shaving duty cycles. First, this module is tested with a full capacity cycle consisting of a charging process (factory default) and a discharging process with a current of 40 A. The battery energy efficiency (discharge vs. charge) is about 90%, and the overall energy efficiency is 80.9%, which includes the auxiliary power used to run the battery management system electronics and self-heating to maintain the module operating temperature (265 °C). Generally, because of the increased self-heating during the holding times that exist for the peak shaving duty cycles, the overall module efficiency decreases slightly for the peak-shaving duty cycles (70.7–71.8%) compared to the full-capacity duty cycle. With a 6 h, peak-shaving duty cycle, the overall energy efficiency increases from 71.8% for 7.5 kWh energy utilization to 74.1% for 8.5 kWh. We conducted long-term cycling tests of the module at a 6 h, peak-shaving duty cycle with 7.5 kWh energy utilization, and the module exhibited a capacity degradation rate of 0.0046%/cycle over 150 cycles (>150 days).

25 ENERGY STORAGE↗
DOE OSTI2023

Origin of the lithium metal anode instability in solid-state batteries during discharge

Enabling the lithium metal anode (LMA) in solid-state batteries (SSBs) would increase energy density and specific energy compared with lithium-ion batteries. However, pore formation in LMAs with irregular morphology, even at low current density, during discharge results in an unstable, high-impedance interface. Understanding and addressing this inherent anode instability is essential for increasing the power densities in SSBs. Herein, we suggest that the morphology of the stripped electrode is related to dislocations in the LMA. To investigate the influence of dislocations, symmetric cells, Li|Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO)|X-Li, are studied, where X-Li represents the microstructurally controlled LMA obtained via suitable thermomechanical processing. Operando impedance measurements are corroborated with SEM, confocal microscopy, and AFM data. Based on the experimental observations, a mechanism for pore formation is proposed. Here we show that the stack pressure required to maintain a stable interface is governed by the lithium microstructure and its thermomechanical processing history.

25 ENERGY STORAGE↗
DOE OSTI2025

Modeling Structured Electrodes and Graded Porosity for Improving Discharge Rate Capability in Ultra-Thick Graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 Batteries

Long-range electric vehicles (EVs) require high-energy-density batteries that also meet the power demands of high current charge and discharge. Ultra-thick (>100 μm) Lithium-ion battery electrodes are critical to enable this need, but slow ion transport in conventional uniform electrodes (UEs) reduces battery capacity at increasing charge/discharge rates. We present a 3D computational analysis on the impact of structured electrode (SE) and graded electrode (GE) geometries on the discharge rate capability of ultra-thick graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) battery cells based on the footprint of a commercial EV pouch cell. SE cathodes with either a “grid” or “line” geometry and GEs with two layers of porosity were modeled. Based on the results of 230 models, we found that the electrolyte volume fraction is a key parameter that impacts capacity improvements in UEs, GEs, and SEs at 2 C–6 C discharge rates. SEs have the greatest discharge rate capability, outperforming GEs and UEs due to reduced Lithium-ion concentration gradients across the electrode thickness, which mitigates electrolyte depletion at high rates. The best SE model has a “grid” geometry with gravimetric and volumetric energy density improvements of 0.9%–4% at C/2–2 C and 18%–24% at 4 C–6 C relative to UEs.

25 ENERGY STORAGE↗
DOE OSTI2024

Understanding the heat generation mechanisms and the interplay between joule heat and entropy effects as a function of state of charge in lithium-ion batteries

The thermal performance of lithium-ion battery cells is critical for ensuring their safe and reliable operation across various applications. In this study, we employed an isothermal calorimetry method to investigate the heat generation of commercial 18650 lithium-ion battery fresh cells during charge and discharge at different current rates, ranging from 0.05C to 0.5C, and across various temperatures: 20 °C, 30 °C, 40 °C, and 50 °C. Our findings revealed a direct correlation between heat generation and current rates, indicating that higher current rates lead to increased heat generation within the cells. Conversely, we observed that heat generation remained relatively stable as the temperature rose, suggesting that temperature changes within this range may not significantly impact the heat generation of fresh cells during typical operations. Furthermore, our study explored irreversible heat generation, which depends on the applied current and overpotential, using the galvanostatic intermittent titration technique at 0.05C–0.5C and 30 °C. Additionally, electrochemical impedance spectroscopy was performed on the same cells during charge and discharge at 20 °C, 30 °C, and 40 °C to analyze cell impedance. Finally, our results indicated a consistent dependence of impedance on the state of charge and depth of discharge, with a significant increase in impedance observed at the end of the discharge process.

25 ENERGY STORAGE↗
DOE OSTI2025

Tool Chain for Simulations of Bi-Filar Coil Winding for Fast Quench Protection

The advancement of high-field magnets utilizing high-temperature superconductors (HTS) brings about complex challenges, especially in quench detection and protection. Traditional methods often fall short due to the inherently slow quench propagation in HTS materials. One promising approach to overcome this involves using a bifilar winding configuration, where two conductors are placed side by side. Under normal operation, they function in series, but during a quench event, they switch to an anti-parallel mode. This shift reduces the differential inductance of the coil to near zero, enabling rapid current oscillations through a capacitor discharge. The resulting high-frequency current flow leads to swift, uniform heating, triggering a full-coil quench within microseconds. Moreover, the strong mutual coupling between the two windings significantly reduces electrical noise in voltage measurements. In this work, we explore the viability of this concept by designing, constructing, and testing a REBCO bifilar racetrack coil in liquid nitrogen. We also present a validated simulation model that closely mirrors the coil's dynamic behavior under these conditions, aligning well with experimental observations.

Jayathilaka, Rehan [Northern Illinois U.]↗
DOE OSTI2023

The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium

The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge T i gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Convex Relaxation of Grid-Connected Energy Storage System Models With Complementarity Constraints in DC OPF

Including complementarity constraints in energy storage system (ESS) models in optimization problems ensure an optimal solution will not produce a physically unrealizable control strategy where there is simultaneous charging and discharging. However, the current approaches to impose complementarity constraints require the use of non-convex optimization methods. Here, we propose a convex relaxation for a common ESS model that has terms for both charging and discharging based on a penalty reformulation for use in a model predictive control (MPC) based optimal power flow (DC OPF) problem. In this approach, the complementarity constraints are omitted and a penalty term is added to the optimization objective function. For the DC OPF problem, we provide analysis for the conditions under which the convex relaxation of the complementarity constraint ensures that a solution with simultaneous ESS charging and discharging operation is suboptimal. Simulation results demonstrating ESS behavior with and without the penalty reformulation are provided for an MPC-based DC OPF problem on multiple IEEE test systems.

25 ENERGY STORAGE↗
DOE OSTI2026

A high power, low temperature molten sodium battery

Low temperature molten sodium batteries promise low-cost, grid-scale energy storage using earth-abundant materials. To be economically viable, they must demonstrate high current (power) at relevant discharge times. Here a low temperature (135 °C) molten sodium battery with a NaI–AlCl 3 molten salt catholyte and NaSICON separator is explored, minimizing cell ohmic resistances and avoiding precipitation reactions in the molten salt catholyte. Operating currents were increased by as much as 100× compared to the energy-dense baseline design (197 Wh kg −1 and 248 mAh cm −2 ). Cells were cycled 100 times at 50 mA cm −2 (150 mW cm −2 ), averaging 99.8% coulombic efficiency and 79.7% energy efficiency for 30% of the theoretical capacity. Charging currents up to 250 mA cm −2 (1070 mW cm −2 ) are demonstrated for 10% of the theoretical capacity. Toward extending the accessible capacity in these high current systems, the volume ratio of catholyte molten salt to a graphite felt current collector was varied, altering (1) the local current density in the graphite felt and (2) the discharge time at a fixed current density. Optimizing the catholyte : felt ratio dramatically increased capacity utilization to 60% (102 mAh cm −2 ) at 50 mA cm −2 (150 mW cm −2 ) charge and 10 mA cm −2 discharge. This catholyte : felt ratio of 1.4 significantly decreased the cell impedance, minimizing electrode blocking effects seen previously in NaI–AlCl 3 catholytes. Together, these high areal loadings and impressive power outputs demonstrate how low temperature molten sodium batteries can compete with commercialized sodium systems operating at more than twice the temperature.

NaSICON↗
DOE OSTI2023

Microstructure and defect engineering of graphite anodes by pulsed laser annealing for enhanced performance of lithium-ion batteries

We report nanosecond pulsed laser annealing significantly improves cyclability and current carrying capacity of lithium-ion batteries (LIBs). This improvement is achieved by engineering of microstructure and defect contents present in graphite in a controlled way by using pulsed laser annealing (PLA) to increase the number density of Li + ion trapping sites. The PLA treatment causes the following changes: (1) creates surface steps and grooves between the grains to improve Li + ion charging and intercalation rates; (2) removes inactive polyvinylidene difluoride (PVDF) binder from the top of graphite grains and between the grains which otherwise tends to block the Li + migration; and (3) produces carbon vacancies in (0001) planes which can provide Li + charging sites. From X-ray diffraction data, we find upshift in diffraction peak or reduction in planar spacing, from which vacancy concentration was estimated to be about 1.0%, which is higher than the thermodynamic equilibrium concentration of vacancies. The laser treatment creates single and multiple C vacancies which provide sites for Li + ions, and it also produces steps and grooves for Li + ions to enter the intercalating sites. It is envisaged that the formation of these sites enhances Li+ ion absorption during charge and discharge cycles. The current capacity increases from an average 360 mAh/g to 430 mAh/g, and C–V shows significant reduction in SEI layer formation after the laser treatment. If the vacancy concentration is too high and charge-discharge cycles are long, then trapping of electrons by Li + may occur, which can lead to Li 0 formation and Li plating causing reduction in current capacity.

25 ENERGY STORAGE↗
DOE OSTI2021

Theoretical analysis of key factors achieving reversed magnetic shear q-profiles sustained with lower hybrid waves on EAST

The phase space analysis technique is applied to provide new insights into the fully non-inductive lower hybrid current driven (LHCD) discharges on EAST (Garofalo et al 2017 Nucl. Fusion 57 076037). The analysis shows that there are bounded and unbounded topologies of lower hybrid (LH) waves in phase space. For typical parameters on EAST, the propagation domain for 4.6 GHz LH waves is bounded, while unbounded for 2.45 GHz LH waves and one of the conditions is recognized to be good for achieving an off-axis current profile driven by 4.6 GHz LH waves on EAST. The parametric analysis on the potential power deposition (PPD) region for those experiments demonstrates that the reversed magnetic shear dominates the wave behavior, and confines the LH power absorption to the far off-axis region as long as it occurs in the 4.6 GHz dominated LHCD discharge. GENRAY/CQL3D simulations also confirm this effect of reversed shear on the power absorption of 4.6 GHz waves. A bounded propagation domain and a positive feedback loop between magnetic shear reversal and off-axis LHCD profile could explain the LH-only-sustained strong reversed magnetic shear observed in experiments on multiple machines. In contrast, there is no such effect for 2.45 GHz waves on EAST since the PPD region is less sensitive to the change of reversed shear due to the unbounded propagation domain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Observation of synergy between lower hybrid waves at two frequencies in EAST

Synergistic effects between two frequencies of lower hybrid (LH) waves—operating at 2.45 and 4.6 GHz—were observed in experiment on EAST for the first time. At low density (ne,lin≈2.0×1019 m−3), simultaneous injection of a 65/35 mix of 2.45/4.6 GHz power achieved an lower hybrid current drive efficiency that was 25% higher than what should be expected from the linear combination of the two sources. The experiment was interpreted with time-dependent simulations, using the equilibrium and transport solver TRANSP, coupled with the ray-tracing code GENRAY and the Fokker–Planck solver CQL3D. For each discharge, profiles of current and hard x-rays from simulation and measurement agree within uncertainties. An examination of the electron distribution function indicates that the LH synergy is supported by the increased width of the LH resonance plateau in the simultaneous injection case compared to independent injection.

Choi, W. (ORCID:0000000268912300)↗
DOE OSTI2023

Capacitive discharge in flash experiments: A discussion of the charged species

Abstract We report on the discharge of the capacitance formed at the electrodes in flash experiments with yttria stabilized zirconia. The experiments were carried out by disconnecting the current, and, instead, short circuiting the electrodes through a resistor. The time dependent voltage across the resistor was measured; the ratio yielded the discharge current. The current decayed exponentially with time, as expected in an RC circuit, which allowed the measurement of the capacitance. Experiments were carried out in two ways. In one case the specimens were flashed within a glove box filled with Ar (< 1 ppm O 2 ): these yielded electronic conductors. In the other case the specimens were flashed in ambient air: while electronically conducting in‐flash these specimens recover their prior insulating behavior as soon as the current is turned off. The stored charge was two orders of magnitude greater in the Ar experiments. Rather unexpectedly, the sign of the voltage expressed at the electrodes was opposite in experiments carried out in air and in Ar. The capacitance measured in the discharge experiments is attributed to the formation of space charge adjacent to the electrodes. In the case of Ar experiments, the capacitance is very large, approaching 1 F; in this case the space charge is expected to be constituted from ions. In the air experiments the specimen becomes insulating, trapping the electrons as a space charge. Hall effect measurements of the carrier density and X‐ray photoelectron spectroscopy characterization of electronically conducting single crystal specimen of cubic zirconia are reported.

Materials Science↗
DOE OSTI2025

Defect-Engineered High-Entropy Spinel Oxide@Onion-Like Carbon Catalysts for High-Areal-Energy Rechargeable Zinc–Air Batteries

Rechargeable zinc-air batteries (ReZAB) have emerged as the next-generation batteries with several advantages over the conventional lithium-ion battery. In this work, single nanocrystals of inverse-type high-entropy spinel oxides (HESOx, particle size of 10−12 nm) confined in highly curved defective onion-like carbons (HESOx/OLC AT ) as efficient electrocatalysts for oxygen evolution reaction (OER), oxygen reduction reaction (ORR), and ReZAB, have been synthesized. The HESOx materials were thoroughly characterized using several analytical techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), Raman, and electron paramagnetic resonance (EPR). HESOx/OLC AT catalyst was tested for ReZAB using literature-recommended parameters that would allow for real technological application. These parameters include a current loading of 10 mA cm −2 and a discharge areal energy density of 35 mWh cm geometric −2 , which maps a Li-ion battery pack-level specific energy of 120 Wh kg pack −1 . HESOx/OLC AT electrocatalysts allowed for continuous discharging and charging at a current loading of 10 mA cm −2 with discharge areal energy densities between 37 and 74 mWh cm geometric −2 , thus outperforming the recommended threshold of 35 mWh cm geometric −2 . Considering that most studies (>90%) hardly meet the recommended threshold for technological application of ReZAB, the present work represents one of the top-performing electrocatalysts for ReZAB. The excellent electrocatalytic properties of defect-rich HESOx/OLC AT toward ORR/OER and ReZAB are governed by the strong electronic modulation arising from d-π hybridization, the availability of multiple catalytic sites for intermediates, and weakened d-band centers of the rate-determining intermediates (i.e., *O adsorption for ORR and *OOH formation for OER) compared to the pristine HESOx. This work introduces an effective approach for the design and synthesis of single nanocrystals of high-entropy electrocatalysts for the development of low-cost, robust, and technologically relevant rechargeable zinc−air batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

A study of resistive peeling–ballooning modes across spherical tokamaks

We investigate how non-ideal-magnetohydrodynamics (MHD) effects, in particular plasma resistivity, impact the peeling–ballooning stability thresholds in spherical tokamaks. This analysis follows the discovery of resistive kink-peeling modes in ELMing National Spherical Torus Experiment (NSTX) discharges. In the present study we extend this modeling to ELMing pulses in the Mega Ampere Spherical Tokamak (MAST) and MAST—Upgrade (MAST-U), where we find a clear resistive scaling for peeling–ballooning modes. While in NSTX ideal-MHD predicts stability for ELMing discharges, in MAST-U we find that the plasma is slightly unstable to peeling–ballooning modes, but is fully stabilized once diamagnetic effects are considered in terms of a growth rate normalization. A resistive power law scaling is calculated for these modes on MAST-U, which lies in between that of tearing modes and resistive interchange modes. A comparison between M3D-C1 and NIMROD shows reasonable agreement for this scaling. Resistivity destabilizes the modes and the peeling–ballooning unstable domain is considerably expanded in both, MAST and MAST-U. In addition to the MAST/-U pulses we also analyze resistive PB stability in a NSTX-similarity discharge on DIII-D. While having a different aspect ratio from NSTX, this discharge uses NSTX-like shaping parameters, toroidal field and plasma current. By considering these discharges alongside NSTX cases, we identify conditions influencing the onset of resistive peeling–ballooning modes. Furthermore, our findings indicate that magnetic shear in the pedestal region is closely linked to the emergence of resistive edge modes.

MAST-U↗