Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrochemical engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A Relief Zone Architecture for Enhanced Durability of Ultrathin Membranes in Electrochemical Conversion Devices

Premature cell failures in electrochemical conversion systems often result when membrane electrode assemblies (MEAs) are prepared with ultra-thin (= 15 micrometer-thick) polymer electrolyte membranes (PEMs). These high-performance PEMs are susceptible to mechanical degradation from stress concentrations arising from component and device-level integration. Herein, a relief zone was developed to mitigate mechanical degradation by alleviating excess and non-uniform compression across the active area. Relief zones, created through the ablation of carbonaceous diffusion material achieves a seamless adaptation across a range of MEA dimensions and electrochemical applications without need for costly hardware modifications. This concept was demonstrated using fuel cells as a case study. Accelerated stress test (AST) validations yielded a 6-fold improvement for MEAs prepared with relief zones (i.e., lifetime approximately 1500 h) compared to those fabricated using conventional edge-protection techniques, showcasing the utility of this technique in decoupling integration and device-level engineering effects from intrinsic material limitations for durable electrochemical devices.

14 SOLAR ENERGY↗
DOE OSTI2024

Chemical preintercalation of magnesium ions into ⍺-MoO 3 structure for improved electrochemical stability in Li-ion cells

Chemical preintercalation of layered materials, used as electrodes in intercalation-based energy storage devices, represents a promising strategy to enhance electrochemical stability and extend cycle life. However, standardized synthesis approaches for the chemical preintercalation of diverse ions into various layered materials are lacking, necessitating the development of specific synthesis routes for each ion and layered phase combination. In this study, we present the first successful demonstration of Mg 2+ ion chemical preintercalation into the interlayer region of α-MoO 3 , revealing its stabilizing effect during cycling in non-aqueous Li-ion cells. Using ethanol during hydrothermal treatment facilitated molybdenum reduction, which was critical for Mg 2+ ion preintercalation. Interestingly, we found that Mg preintercalation was accompanied by the incorporation of water. Mg-preintercalated α-MoO 3 exhibited enhanced charge storage capacity, electrochemical stability, and power capability compared to pristine α-MoO 3 electrodes. This improved performance is attributed to the structural stabilization provided by Mg 2+ pillars, which prevent undesirable phase transformations during repeated Li intercalation/deintercalation, and increased Li + ion diffusion due to the shielding of electrostatic interactions between electrochemically cycled ions and the α-MoO 3 lattice, enabled by structural water. In conclusion, our study offers new insights into developing chemical preintercalation synthesis approaches that can be broadly applied to a wide range of pillaring ions and layered material hosts.

25 ENERGY STORAGE↗
DOE OSTI2022

Elucidating facet dependent electronic and electrochemical properties of Cu 2 O nanocrystals using AFM/SCEM and DFT

Cuprous oxide (Cu 2 O) has extensively been studied owing to its excellent optical, magnetic, and catalytic properties. Many of these properties are facet-dependent and have not been well elucidated. This work synthesized cubic, cuboctahedral, octahedral, and rhombic dodecahedral shaped Cu 2 O nanocrystals of ~300 nm in size to evaluate the facet-dependent electrochemical activities. Here, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were firstly used to reveal the average electrochemical activities at the ensemble level. Atomic force microscopy-scanning electrochemical microscopy (AFM-SECM) was further used to assess the electrochemical activities of different Cu 2 O nanocrystals at the facet level. Hexaammineruthenium (III) chloride ({Ru(NH 3 ) 6 }Cl 3 ) was employed as the probe molecules that reacted with four different Cu 2 O nanocrystals under —400mV and yielded ~300 pA current between the probing tip and the nanocrystal surface. The tip-current mapping results indicate that rhombic dodecahedral Cu 2 O exhibits higher electrocatalytic activity than other shaped Cu 2 O, due to the presence of dominant exposed facet of {110} as indicated by the relatively high tip current. Density-functional theory (DFT) calculations confirmed the facet dependence of local surface energy and electronic structure of Cu 2 O nanocrystals. Besides electrochemical activity, the surface work function and adsorptive properties were both observed to vary with the shape and dominant exposed facets of Cu 2 O. This study presented a unique experimental and computational chemistry approach to analyze surface electrochemical properties of Cu 2 O crystals at a crystalline facet level.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding LIB Battery Electrodes Through Classical Electrochemical Interface Theory

Classical models of the electrochemical interface can be applied to complex and dynamic electrodes to understand important mechanisms that are relevant to device-level phenomena like calendar aging or cycle life. Here, we show that negative alloy electrodes with wide electrochemical windows cannot be assumed to have static interfaces throughout all states of charge. Under high states of charge, the interface -including the solid electrolyte interphase - has characteristics that resemble a highly polarized electrode far from the point of zero charge. Under these conditions, the interface can be understood through the Helmholtz model. At lower states of charge, the interface capacitance decreases and the space charge layer length increases. This transformation resembles a metal electrode approaching the point of zero charge which is understood through the Gouy-Chapman-Stern-Grahame model of the electrochemical interface. This transformation happens at both silicon and carbon-coated silicon interfaces. From voltage-limited cycling experiments, in the limit of the diffuse double layer, the silicon electrode impedance rises significantly in the first few cycles. This rise is related to the continuous electrochemical reduction of electrolyte components from an interface that is not electronically screened from the electrolyte. In other words, an electrode interface for batteries should resemble a 'Helmholtz-like' structure.

anode↗
DOE OSTI2025

Tailoring the Reaction Heterogeneity for Robust Li‐Rich Cathodes

The practical application of Li-rich Mn-based layered oxides (LLO) cathode is hindered by severe capacity and voltage degradation resulting from severe oxygen release and irreversible phase transition. In this work, the reaction heterogeneity, which describes the spatially resolved electrochemical divergence within individual cathode particles, is engineered through compositional gradient design to couple Li + transport kinetics and the anion redox activity between particle interiors and surfaces. It is revealed that Co/Mn concentration gradient within particles creates heterogeneous phase content distribution and structural ordering, inducing surface-bulk reaction heterogeneity that significantly impacts the overall electrochemical performance. Specifically, Li 2 MnO 3 -poor and Co-enriched surface effectively mitigates the oxygen loss and enhances electrochemical reaction kinetics, benefited from the reduced surface redox reactivity and induced highly ordered intra-layered cationic arrangement. Meanwhile, the Li 2 MnO 3 -enriched core with slight Li/Ni intermixing provides high reversible capacity and strong mechanical stability. Consequently, the greatly enhanced anion redox reversibility, Li + diffusion dynamics, and structure stability endow LLO with exceptional electrochemical properties, showing a capacity retention of 86.0% and a reduced voltage decay of 0.518 mV per cycle after 500 cycles at 1 C. This work provides a valuable strategy to tailor the redox chemistry and achieve robust LLO.

25 ENERGY STORAGE↗
DOE OSTI2020

Alternative route for electrochemical ammonia synthesis by reduction of nitrate on copper nanosheets

We propose an efficient and clean avenue for ammonia synthesis, via electroreduction of nitrate which could be obtained from industrial wastewater, domestic sewage, sodium nitrate ore, and nitrification of bacteria and electrochemical oxidation of nitrogen, which addresses the water pollution issues and simultaneously upgrades the nitrate to high-value ammonia. At a low overpotential of -0.15 V versus RHE, Cu nanosheets achieved an ammonia formation rate of 390.1 μg mg -1 Cu h -1 and a Faradaic efficiency of 99.7%, attributed to suppression of the HER activity and apparent improvement of the rate of rate-determining step on Cu (111). Such an ammonia formation rate is more than two orders of magnitude higher than electrochemical nitrogen reduction reaction to ammonia. This work not only develops a powerful strategy to the rational design of robust and efficient catalysts by crystal facet engineering, but also provides an alternative route for electrochemical ammonia synthesis by reduction of nitrate.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Cost-Performance Analysis of a Sodium Heat Engine for Distributed Concentrating Solar Power

We present that a sodium thermal electrochemical converter (Na-TEC) generates electricity directly from heat through isothermal expansion of sodium ions across a beta"-alumina solid-electrolyte. This heat engine has been considered for use with conventional concentrating solar power (CSP) systems before. However, unlike previous single-stage devices, the improved design uses two stages with an interstage reheat, allowing more economical and efficient conversion up to 29% at a hot side temperature of 850 °C. Herein, a cost-performance analysis for this improved design assesses opportunities for distributed-CSP in the context of micro-combined heat and power systems. A high-level techno-economic analysis (TEA) is presented that explores four scenarios where a Na-TEC is used as the heat engine for a distributed-CSP system. Overnight capital cost and levelized cost of electricity (LCOE) are estimated for a system lifetime of 30 years, revealing that overnight capital costs in a range from $3.57 to $17.71 per W e are feasible, which equate to LCOEs from 6.9 to 17.2 cents kWh e -1 . This analysis makes a significant contribution by concurrently quantifying the efficiency and unit costs for a range of multistage configurations, and demonstrating that a Na-TEC may be a promising alternative to Stirling engines for distributed-CSP systems at residential scale of 1–5 kW e .

14 SOLAR ENERGY↗
DOE OSTI2026

Powder‐to‐Film Conversion of Nickel Single‐Atom Catalysts into Binder‐Free and Resistant Electrodes

Although a few binder-free and self-supported single-atom electrodes have been reported, achieving mechanically robust, defect-engineered, and reproducible films that preserve atomic dispersion under electrochemical operation remains challenging. This work addresses this limitation by presenting a versatile and generalizable strategy to transform powders into standalone, defect-engineered thin films hosting atomically dispersed Ni centers within conductive 2D frameworks. The physicochemical and electronic properties of these materials are thoroughly characterized using a comprehensive set of spectroscopic and microscopic techniques and confirmed the homogeneous dispersion and monoatomic nature of the Ni centers (0.94 wt.%) on the electrode films. Electrochemical testing via cyclic voltammetry and electrochemical impedance spectroscopy under a range of experimental conditions revealed that integration of Ni single atoms markedly enhanced performance and stability compared to carbon nanotube-only electrodes, maintaining integrity after 15 h of continuous operation. This improvement is accompanied by a notable reduction in charge transfer resistance (30.50 Ω) and an increase in double-layer capacitance (295.45 µF). Post-electrochemical analyses corroborated the structural integrity and robustness of the electrodes. Overall, this work bridges atomically precise catalysis and device-level electrochemistry, opening a route toward reproducible and scalable single-atom electrodes for sensing and energy conversion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Lithiation-Induced Defect Engineering to Promote Oxygen Evolution Reaction

Exploring efficient electrocatalysts for oxygen evolution reaction (OER) is an urgent need to advance the development of sustainable energy conversion. Though defect engineering is considered an effective strategy to regulate catalyst activity for enhanced OER performance, the controllable synthesis of defective oxides electrocatalysts remains challenging. Here, oxygen defects are introduced into NiCo 2 O 4 nanorods by an electrochemical lithiation strategy. By tuning in situ lithiation potentials, the concentration of oxygen defects and the corresponding catalytic activity can be feasibly regulated. In addition, the relationship between the changes in the defect density and electronic structure and the lithiation cut-off voltages is revealed. The results show that NiCo 2 O 4 nanorods undertook intercalation and two-step conversion reaction, in which the lithiation-induced conversion reaction gives rise to a CoO@NiO-based structure with higher defect density and lower oxidation states. As a result, the defective CoO@NiO-based catalyst exhibits exceptional OER activity with an overpotential of 270 mV at 10 mA cm -2 , which is about 74 mV below the pristine nanomaterials. In conclusion, this research proposes a novel strategy to explore high-performance catalysts with structural stability and defect control.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Oxadiazole derivatives as stable anolytes for >3 V non-aqueous redox flow battery

Effective utilization of energy from renewable sources such as wind and solar requires the development of long duration energy storage (LDES) systems that can accommodate intermittent energy accrual. One option under investigation is the use of a redox flow battery (RFB). A significant amount of work has explored aqueous RFB systems with a variety of inorganic and organic carriers. However, moving to a nonaqueous solvent such as acetonitrile (MeCN) for RFB provides a much larger electrochemical window, which could lead to increased energy density if properly utilized. Here, in this work, we investigate a series of 2,5-diphenyl-1,3,4-oxadiazole (DiPhenOx) derivatives as anolytes for a redox flow battery. DiPhenOx has a low voltage redox event that, while reversible by cyclic voltammetry, was determined to be irreversible during bulk electrolysis. To improve cycling performance, we introduced various ester and cyano groups to the phenyl rings of DiPhenOx using molecular engineering. We characterized these derivatives spectroscopically and electrochemically to assess their feasibility for flow battery applications. The ester derivatives with the best cycling performance were tested in a flow cell vs. ferrocene, 2,5-di-tert-butyl-1,4-bis(2-methoxyethoxy)benzene (DBBB) and thianthrene, which resulted in ~2 V, ~3 V and ~3 V redox flow batteries, respectively.

25 ENERGY STORAGE↗
DOE OSTI2023

Single molecule insights into interfacial molecular recognition for model electrochemical DNA biosensors

Electrochemical sensors that use surface-immobilized DNA to bind analytes and transduce the binding into electrochemical signals, have the potential for rapid, specific, and sensitive detection of bioanalytes via a compact and portable platform. However, accessing the structure of these surfaces/interfaces at the relevant spatial scale (< 10 nm), which determines the interfacial interactions and ultimately sensing performance, remains an unsolved challenge. Here, we review studies that have used high resolution atomic force microscope imaging and spatial statistical analysis tools to understand crowding interactions between thiolated DNA probes immobilized on gold electrodes and how such interactions impact target binding. We also review related studies that attempt to control the nanoscale spatial arrangement of the immobilized recognition elements to optimize sensing performance. Furthermore, these efforts have led to new advances in understanding of the structure-function relationships of DNA-based electrochemical biosensors to move the field toward rational engineering of these biosensing interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Reversible Polymer–Metal Mechanical Transitions Enabled by Electrochemical Modulation

The mechanical properties of materials, e.g., elastic modulus and hardness, are important for many engineering applications. Here, we introduce a hierarchically ordered structure (HOS) polymer system that exhibits exceptionally large, reversible changes in mechanical behavior upon electrochemical lithiation and delithiation. Full lithiation of the HOS polymer induces a substantial mechanical transition from polymer-like to metal-like attributes, yielding a 10-fold increase in elastic modulus and a 3-fold increase in hardness, with values comparable to those of aluminum. Upon removal of Li+ ions, the elastic modulus and hardness return to nearly pristine polymer levels, and this transformation remains highly repeatable over many electrochemical cycles. Reversible transitions between polymer-like and metal-like mechanical behaviors offer a new pathway for engineering materials for applications that require tunable mechanical properties, such as soft robotics and stimuli-responsive systems.

Thapa, Santosh↗
DOE OSTI2024

Double Hydroxide Nanocatalysts for Urea Electrooxidation Engineered toward Environmentally Benign Products

Abstract Recent advancements in the electrochemical urea oxidation reaction (UOR) present promising avenues for wastewater remediation and energy recovery. Despite progress toward optimized efficiency, hurdles persist in steering oxidation products away from environmentally unfriendly products, mostly due to a lack of understanding of structure‐selectivity relationships. In this study, the UOR performance of Ni and Cu double hydroxides, which show marked differences in their reactivity and selectivity is evaluated. CuCo hydroxides predominantly produce N 2 , reaching a current density of 20 mA cm geo −2 at 1.04 V – 250 mV less than NiCo hydroxides that generate nitrogen oxides. A collection of in‐situ spectroscopies and scattering experiments reveal a unique in situ generated Cu (2‐x)+ ‐OO −• active sites in CuCo, which initiates nucleophilic substitution of NH 2 from the amide, leading to N‐N coupling between * NH on Co and Cu. In contrast, the formation of nitrogen oxides on NiCo is primarily attributed to the presence of high‐valence Ni 3+ and Ni 4+ , which facilitates N‐H activation. This process, in conjunction with the excessive accumulation of OH − ions on Jahn‐Teller (JT) distorted Co sites, leads to the generation of NO 2 − as the primary product. This work underscores the importance of catalyst composition and structural engineering in tailoring innocuous UOR products.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Engineering Thermally Resilient and Kinetically Active Reversible Protonic Ceramic Cells via Interfacial Design

Achieving concurrent fast electrode kinetics and long-term thermo-mechanical durability remains a critical challenge for reversible protonic ceramic electrochemical cells (R-PCECs). Herein, we report an interfacial engineering strategy that integrates a perovs.kite-type PrBaRu0.1Co1.9O5+δ (PBRC) nanoparticle layer onto a PrBa0.5Sr0.5Co1.5Fe0.5O5+δ (PBSCF) substrate (PBRC-PBSCF), together with a modified pellet-assisted sintering approach to fabricate dense BaZr0.4Ce0.4Y0.1Yb0.1O3-δ (BZCYYb4411) electrolytes. The in situ reconstructed heterointerface enhances oxygen reduction/evolution reaction (ORR/OER) kinetics, promotes H2O adsorption/dissociation, and improves steam tolerance, as verified by electrochemical measurements and interfacial microstructural analyses. Density functional theory reveals that Ru-induced electronic modulation at the PBRC-PBSCF interface lowers the energy of oxygen vacancy formation and optimizes the position of the O 2p band center, thereby accelerating oxygen redox kinetics and stabilizing the interface. The resulting R-PCECs deliver an excellent peak power density of 1.112 W cm−2 and an electrolysis current density of −1.257 A cm−2 at 1.3 V in 3% H2O wet air at 600°C, with a reasonable faradaic efficiency. Furthermore, the cells demonstrate excellent stability, sustaining 100 h of thermal cycling (400–600°C, 200°C h−1) in both fuel cell and electrolysis modes, with 600 h of stability in electrolysis mode (600°C, −0.5 to −2 A cm−2).

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Optimizing Li‐Excess Cation‐Disordered Rocksalt Cathode Design Through Partial Li Deficiency

Li-excess disordered rocksalts (DRXs) are emerging as promising cathode materials for Li-ion batteries due to their ability to use earth-abundant transition metals. In this work, a new strategy based on partial Li deficiency engineering is introduced to optimize the overall electrochemical performance of DRX cathodes. Specifically, by using Mn-based DRX as a proof-of-concept, it is demonstrated that the introduction of cation vacancies during synthesis (e.g., Li 1.3-x Mn 2+ 0.4-x Mn 3+ x Nb 0.3 O 1.6 F 0.4 , x = 0, 0.2, and 0.4) improves both the discharge capacity and rate performance due to the more favored short-range order in the presence of Mn3+. Density functional theory calculations and Monte Carlo simulations, in combination with spectroscopic tools, reveal that introducing 10% vacancies (Li 1.1 Mn 2+ 0.2 Mn 3+ 0.2 Nb 0.3 O 1.6 F 0.4 ) enables both Mn 2+ /Mn 3+ redox and excellent Li percolation. However, a more aggressive vacancy doping (e.g., 20% vacancies in Li 0.9 Mn 3+ 0.4 Nb 0.3 O 1.6 F 0.4 ) impairs performance because it induces phase separation between an Mn-rich and a Li-rich phase.

25 ENERGY STORAGE↗
DOE OSTI2020

Revealing the Structural Evolution and Phase Transformation of O3-Type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 Cathode Material on Sintering and Cycling Processes

O-type layered oxide cathode materials can be easily synthesized for a full sodium stoichiometry with high specific capacity, but they all suffer from a capacity fade on cycling. The sintering process control and optimization are critical to ensure a high quality and consistency of the prepared cathode materials with stable structure. Herein, in situ high-energy X-ray diffraction (HEXRD) was first employed to investigate the phase evolution of the oxides during the sintering process of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 . The in situ HEXRD and both operando Bragg coherent diffraction (BCXD) and coherent multicrystal diffraction (CMCD) were utilized to investigate the phase transformation of the cathode materials during the sodiation/desodiation process. A composite structure comprised of O-type and P-type oxides was formed after the initial electrochemical activation of the cathode material, resulting in good structural and electrochemical stability. This finding implies that strain engineering can be a new design philosophy for the development of next generation high-performance sodium ion cathodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Binder Effects on Processing, Mechanical Properties, and Performance of Thin Sulfide Solid‐State Electrolytes

All‐solid‐state batteries (ASSBs) offer enhanced safety and energy density compared to conventional lithium‐ion batteries by replacing flammable liquid electrolytes with solid‐state electrolytes (SSEs). Among SSEs, sulfide‐based electrolytes exhibit high ionic conductivity and mechanical deformability, making them promising candidates for next‐generation energy storage. However, their practical implementation is hindered by interfacial instability, mechanical brittleness, and challenges in fabricating ultrathin electrolyte membranes (<30 μm) with robust mechanical integrity. Here, this study systematically examines the influence of polymeric binders—polyisobutylene, hydrogenated nitrile butadiene rubber, and styrene–ethylene–butylene–styrene (SEBS)—on the structural, mechanical, and electrochemical performance of thin sulfide SSE membranes. Key findings reveal that SEBS enables the fabrication of ultrathin, uniform membranes, while binder elasticity significantly affects structural stability during cycling. Operando stack pressure measurements indicate that binder properties directly influence adhesion force for LPSCl particles, influencing their stabilizing cycling period. These results underscore the critical role of polymer binders beyond mechanical reinforcement, positioning them as essential design variables in sulfide SSE engineering. By linking binder chemistry to processability and electrochemical performance, this study provides insights into optimizing sulfide SSEs, advancing their commercial viability in ASSBs.

argyrodite sulfide electrolyte↗