Search NASA⌕ Search

SEARCH · Search NASA

Results for “experimental investigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Investigation of Elastodynamic Nonlinear Response of Dry Intact, Fractured and Saturated Rock

Nonlinear elastodynamic response of fractured rocks carries crucial information on fracture features that can be exploited to forecast flow properties, friction constitutive behavior and poromechanical response. Well-controlled laboratory experiments are designed to measure the nonlinear elastodynamic response of Westerly granite in three states: dry intact, dry fractured and saturated fractured. We study the effect of fracturing and saturation in modifying the elastodynamic response of the rock. Each sample is tested at a normal stress level of 15 MPa. We measure the elastodynamic response of an intact L-shaped sample of Westerly Granite subjected to normal stress oscillations of prescribed amplitudes (0.2–1 MPa) and frequencies (0.1, 1, 10 Hz). Ultrasonic waves transmitted across the sample are used to monitor the evolution of wave velocity before, during and after dynamic stressing. Furthermore, the nonlinearity of the elastodynamic response is measured in terms of: (1) the offset in normalized wave velocity; (2) the amplitude of wave velocity fluctuation during the oscillations; and (3) recovery rate of the wave velocity post-oscillation. We observe that the three nonlinearity parameters show a similar trend. Irrespective of the parameter, the nonlinearity measures higher for sample in dry-intact condition than that for dry-fractured and the saturated-fractured sample exhibits smaller nonlinearity than the dry-fractured sample. As expected, the saturated sample exhibits less nonlinearity than the dry intact and fractured samples due to the presence of interstitial fluid and the resulting increased interface stiffness. Conversely, the dry intact rock shows a higher nonlinearity than the dry fractured. We use numerical simulations to show that the presence of fracture significantly alters the strain distribution across the bulk of the sample and only the contacting asperities are highly strained, thus resulting in a decrease in the measured elastodynamic nonlinearity.

58 GEOSCIENCES↗
DOE OSTI2022

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

Abstract Laser powder bed fusion (L-PBF) is currently the additive manufacturing process with the widest industrial use for metal parts. Yet some hurdles persist on the way to a widespread industrial serial production, with reproducibility of the process and the resulting part properties being a major concern. As the geometry changes, so do the local boundary conditions for heat dissipation. Consequently, the use of global, geometry-independent processing parameters, which are today’s state of the art, may result in varying part properties or even defects. This paper presents a numerical simulation as a method to predict the geometry-dependent temperature evolution during the build. For demonstration, an overhang structure with varying angles towards the build platform was manufactured using Ti–6Al–4V. A calibrated infrared camera was integrated into a commercial L-PBF system to measure the temperature evolution over time for a total build height of 10 mm, and the results are used for validation of the simulation. It is shown that the simulation is capable of predicting the temperature between layers. The deviations between simulation and measurement remain in single digit range for smaller overhang structures (90°, 60° and 45°). For large overhang structures (30°), the simulation tends to over-predict the temperatures up to 15 °C. Experiments with varying process parameters showed the feasibility of energy reduction as compensation of the heat accumulation produced by overhang structures.

Li, Gefei (ORCID:0000000174837952)↗
DOE OSTI2023

Experimental investigation of advanced turbine control strategies and load-mitigation measures with a model-scale floating offshore wind turbine system

To advance the control co-design of offshore wind energy systems, the authors perform basin-scale experiments with a fully instrumented and actuated floating offshore wind turbine model. The model consists of a 1:70 scale performance-matched model of the International Energy Agency Wind Technology Collaboration Programme 15-MW reference turbine atop the VolturnUS-S semisubmersible platform. The Reference OpenSource Controller provides real-time blade pitch and generator torque control. Here we aim to develop an open data set for the validation of numerical models in predicting the influence of turbine control and load-mitigation measures. For this purpose, we measure the effects of advanced turbine control features, including peak shaving and floating feedback as well as hull-based control using tuned mass dampers on the system. Overall, the results demonstrate measurable and consistent influences from the control and load-mitigation measures, thus confirming the usefulness as a validation data set. Peak shaving attenuates the response to wind turbulence at near-rated wind speed. Floating feedback reduces the load and platform pitch motion associated with the negative damping induced by blade pitch control. The tuned mass dampers also attenuate the system response near the targeted frequencies under suitable conditions. We also identify detrimental side effects of each load-mitigation measure.

17 WIND ENERGY↗
DOE OSTI2021

High pressure experimental investigation of clinopyroxene dissolution in a K-basaltic melt

Dissolution of clinopyroxene (cpx) in a K-basaltic melt from the Campi Flegrei Volcanic District (Italy) has been investigated through dissolution and dissolution-crystallization experiments at pressure of 0.8 GPa, superliquidus temperature of 1350 °C, and dwell times between 0.5 and 1 h. The obtained dissolution rates range from 7.9·10 –6 cm s –1 to 6.1·10 –6 cm s –1 as a function of dwell time. In the dissolution-crystallization experiment (1300 °C; 0.8 GPa; 2 h), the formation of overgrowth rims accompanied by new cpx crystals suggests that the injection of recharge magmas in basaltic reservoir may lead to inverse or oscillatory zonation. The interaction between cpx and K-basaltic melt at ~1570 °C was studied by in situ radiography using synchrotron radiation combined with the Paris-Edinburgh press. Here, this resulted in cpx resorption to occur depending on the temperature conditions with respect to the liquidus temperature of the cpx (T cpxL ). The calculated cpx dissolution rates are ~5·10 –3 cm s –1 at T ≤ T cpxL and ~ 3·10 –2 cm s –1 at T ≥ T cpxL . The role of crystal dissolution in the estimation of magma residence times has been also tested for a natural magmatic system by interpolating the dissolution rates (~10 –5 –10 –6 cm s –1 ) with the textural data of cpx phenocrysts from the Agnano-Monte Spina pyroclastic deposit at Campi Flegrei caldera (Campanian region, Italy). Results from calculations indicate that the time required for partial or complete resorption of phenocrysts varies from ~0.5 to ~40 h, and that the effect of crystal dissolution may be relevant to estimate magma residence times whether significant dissolution occurs during magma mixing processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

The mechanical behaviors and damage evolutions of carbon/epoxy woven fabric composites with three different geometries, i.e., one plain weave and two twill weave patterns with different areal densities, are studied under tensile loading. The effects of weave patterns on mechanical properties are investigated by monotonic and cyclic tension tests. Remarkable variations in stress–strain curve, Poisson’s ratio, residual strain and strain map exist in the three composites. Crimp ratio is found to be a critical factor to govern the mechanical properties. With smaller crimp ratio, a quasi-linear stress–strain curve with higher elastic modulus and strength is observed. The stress–strain curves of composites with higher crimp ratio contain transition stages with significant tangent modulus degradation. Elastic modulus, strength and damage initiation are all correlated with the crimp ratio linearly regardless of the fabric pattern. Dramatic nonlinear evolution in Poisson’s ratio occurs in the composite with higher crimp ratio. Cyclic tension results indicate that the residual strain is a more appropriate damage indicator than the unloading elastic modulus. Microstructure examination shows that damage developments are essentially related to the fabric geometry, and result in various mechanical behaviors. This work provides important insights into the geometry-deformation mechanism-mechanical property relationship of the woven composites.

36 MATERIALS SCIENCE↗