SEARCH · Search NASA

Results for “flow focusing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Comparison of wind farm control strategies under realistic offshore wind conditions: turbine quantities of interest

Abstract. Wind farm flow control is a strategy to increase the efficiency and therefore lower the levelized cost of energy of a wind farm. This is done using turbine settings such as the yaw angle, blade pitch angles, or generator torque to manipulate the flow behind the turbine, affecting downstream turbines in the farm. Two inherently different wind farm flow control methods have been identified in the literature: wake steering and wake mixing. This paper focuses on comparing the turbine quantities of interest between these methods for a simple two-turbine wind farm setup, while a companion article (Brown et al., 2025) focuses on the wake quantities of interest for a single wind turbine setup. Both papers use the same set of wind farm simulations based on high-fidelity large-eddy simulations (LESs) coupled with OpenFAST turbine models. First, precursor simulations are executed in order to match wind conditions measured with lidars in an offshore wind farm off the east coast of the USA. These measurements show general wind conditions that exhibit substantially higher vertical wind shear and veer than any of the LES studies performed with wind farm flow control strategies currently available in the literature. The precursors are used to evaluate the effectiveness of the control methods. In the LES, the wind veer leads to highly skewed wakes, which have considerable influence on the power uplift of wind farm flow control strategies. In addition to a baseline controller, four different control strategies, each of which uses either pitch or yaw control, are performed on the upstream turbine of a simple two-turbine wind farm. Assuming that the wind direction is known and constant over time, the simulations show that wake steering is generally the superior wind farm flow control strategy, considering both wind farm power production and turbine damage equivalent loads when substantial wind veer is present. This result is consistent over different wind speeds and wind directions. On the other hand, for similar wind conditions with lower veer, wake mixing was found to yield the highest power production, although at the expense of generally higher loads. This leads us to conclude that the effect of wind veer, which has so far not usually been considered, can not be neglected when determining the optimal wind farm flow control strategy.

17 WIND ENERGY↗

DOE OSTI2025

Design and Analysis of the Open-Surface Slow Li Flow Divertor and Comparison to the Fast Li Flow Divertor

In the ongoing U.S. project, “Liquid Metal Plasma Facing Components,” sponsored by the U.S. Department of Energy, efforts have been taken to develop two open-surface divertor designs for the Fusion Nuclear Science Facility using liquid lithium (Li) as a heat and particle flux removal media. The main focus of this study is the design and analysis of a slow (~1 mm/s) and thin (<1 mm) open-surface Li flow divertor with a Li-cooled substrate, which is then compared with an earlier design of a fast (up to 10 m/s) and thick (~0.5 cm) Li flow divertor with the substrate cooled with helium. The slow Li flow divertor design is based on the original LiWall concept developed at the Princeton Plasma Physics Laboratory. Such a thin and slow Li layer can remove the particle flux by reducing the recycling flux, while the heat flux is removed mainly through the heat sink located beneath. In the present study, the heat sink is provided through a Li cooling flow inside the substrate of reduced activation ferritic/martensitic steel. By performing a multiphysics analysis with COMSOL that included liquid-metal magnetohydrodynamics (MHD), heat transfer, and structural mechanics, the impact of various factors on the divertor heat removal capability, such as Li flow velocity, MHD effects, and inlet velocity boundary condition, were examined. Based on comparisons of the two divertor designs, it was shown that the fast-flow divertor significantly outperformed the slow-flow design, whose heat removal capability was limited to ~1 to 2 MW/m2.

Jiang, Yuchen [ORNL] (ORCID:0000000283280284)↗

DOE OSTI2024

Simulation of Multiphase Flow and Poromechanical Effects Around Injection Wells in CO 2 Storage Sites

In geological CO 2 storage operations, wellbore deformations and leakage pathways formations can occur around injection and abandoned wells subjected to high rates and long-term CO 2 injection. To guide engineering design and prevent CO 2 leakage risks, a full understanding of the underlying physics and robust numerical models is necessary to evaluate the response of underground formations in the near wellbore region and in the reservoir. In this study, a multi-scale and multi-physics open-source simulator (GEOS) is used to simulate multiphase flow and poromechanical deformations over time in three dimensions. The governing equations for mechanical deformations of the rock body and multiphase compositional fluid flow within the rock matrix are solved with a fully coupled finite element and finite volume approach. The Drucker–Prager model with friction hardening is applied to simulate elastoplastic deformation and a multiphase fluid model with power-law correlations for relative permeability is used to model the migration of CO 2 plume, which are coupled with numerical implicit scheme. Simulation results are verified against multiple analytical solutions for multiphase flow and wellbore problems, thus demonstrating the accuracy of this advanced simulator. In two engineering applications, here we highlight the impact of elastoplastic deformation and coupled modeling for assessing induced displacements and stress perturbations, which are more pronounced in the near wellbore regions. This work focuses on short-term processes in the vicinity of injection wells where stress evolutions, rock deformations and multiphase compositional flow and transport are simulated jointly to ensure wellbore stability and prevent damage. This fully coupled geomechanical model can simulate multiphase flow and any associated poromechanical effects within the CO 2 storage site and in the surrounding formations. Such a large-scale, long-term, multi-physics simulation model is useful in many ways: it can guide operational decisions for CO 2 injection, assess the containment potential and risks of a site, and analyze the wellbore stability and integrity during and after CO 2 injection.

58 GEOSCIENCES↗

DOE OSTI2025

Staircases of passive and active scalar concentration in cellular flow

This paper develops a unified model for staircase formation in both passive and active scalar systems, building upon prior numerical studies by offering new heuristic and physical insights. While prior studies primarily reported numerical results, they did not explore the underlying unifying physics that governs both types of scalar transport; this work addresses that gap by identifying shared mechanisms across both cases. Results of studies of passive and active scalar staircase formation in cellular flows are presented. Staircase formation in cellular flows occurs due to the interplay of fast mixing within cells and slow transport across the inter-cell boundary. The cell boundary emerges as a de facto transport barrier. Special attention is focused on the effects of cellular fluctuations and noise upon staircase structure. A forced, fluctuating vortex array model is used to drive the underlying flow structure. Cellular Peclet number and staircase profile curvature are identified as figures-of-merit to quantify the resiliency of layering. These are related to simple, multi-scatterer scalar random walk models. Results for Peclet number and curvature scaling with flow excitation are presented. We also study staircases of magnetic potential evolving in two-dimensional magnetohydrodynamics as examples of layering of active scalar concentration. Formation of magnetic potential staircases is indeed observed. Flux expulsion inhibits the intercellular transport of magnetic potential and strengthens staircase barriers. Magnetic staircases can be supported against resistive decay by magnetic potential noise forcing. Implications for staircase formation in magnetic confinement experiments are discussed.

Control theory↗

DOE OSTI2024

Explicit entropic proofs of irreversibility theorems for holographic RG flows

We revisit the existence of monotonic quantities along renormalization group flows using only the Null Energy Condition and the Ryu-Takayanagi formula for the entanglement entropy of field theories with anti-de Sitter gravity duals. In particular, we consider flows within the same dimension and holographically reprove the c-, F -, and a-theorems in dimensions two, three, and four. We focus on the family of maximally spherical entangling surfaces, define a quasi-constant of motion corresponding to the breaking of conformal invariance, and use a properly defined distance between minimal surfaces to construct a holographic c-function that is monotonic along the flow. We then apply our method to the case of flows across dimensions: there, we reprove the monotonicity of flows from AdS D+1 to AdS 3 and prove the novel case of flows from AdS 5 to AdS 4 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2025

Hydrological Controls on Riverbed Methane Emissions: A Numerical Investigation of Hydrodynamic and Ebullitive Mechanisms from Site to Basin Scales

Methane production and emission from riverbed sediments constitute a significant yet underexplored component of the river methane budget. Despite their importance, a mechanistic and quantitative understanding of these processes under dynamic flow conditions remains elusive, particularly at the basin scale. In this study, we investigate the multiscale (site-to-basin) mechanisms governing methane emissions from riverbeds, focusing on the interplay between biogeochemical processes and hydrological dynamics. We developed a reactive transport model that integrates methane production with hydrodynamic and ebullitive pathways and coupled it with a basin-scale groundwater flow model to simulate methane emissions across scales. By incorporating key factors such as vertical hydrological exchange flow (VHEF), particulate organic carbon availability, sediment properties, and temperature sensitivity, our model captures the spatiotemporal variability of methane ebullition at both the site and basin scales. Our results reveal that methane ebullition is strongly modulated by VHEF, with lower flow rates promoting methane accumulation and subsequent ebullition. Sensitivity analyses underscore nonlinear responses of methane fluxes to environmental drivers. Furthermore, these findings emphasize the critical roles of sediment composition, hydrological exchange, and environmental conditions in shaping methane dynamics. Overall, this work advances our understanding of riverine methane emissions and offers insights for guiding climate models and mitigation strategies.

Fluxes↗

DOE OSTI2026

Margin to onset of nucleate boiling and flow instability studies for preliminary MITR design-demonstration element thermal-hydraulics

This study covers the onset of flow instability (OFI) preliminary results obtained from leveraging correlations, in addition to the preliminary thermal hydraulics results such as pressure, flow velocity, temperature, and oxide layer over the design demonstration experiment (DDE) for the Massachusetts Institute of Technology Reactor (MITR). Current computational fluid dynamics (CFD) models in fluid structure interaction (FSI) have added the capability of assessing margins to onset of nucleate boiling (ONB). This study initiates the capability to model the margin to OFI and ONB presented for the MITR. Such study is supportive of the United States High Performance Research Reactor (USHPRR) program. Previous studies provided preliminary thermal-hydraulic and mechanical analyses of the hydrodynamic effects in the MITR DDE under conservative approximations for plate power distribution. In conclusion, this study focuses on providing insights into the OFI future research direction optimizing the transport of thermal energy, mass-flow rates, flow-channel geometries, and boundary conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Methods for Quantitative Thermal Analysis of Lithium Solid-State and Beyond Battery Safety

The use of differential scanning calorimetry (DSC) to measure the thermal behavior of individual components and electrolyte/electrode combinations is common. However, here we focus on DSC tests on an anode, cathode, and electrolyte (ACE) component combination over a temperature range that includes many of the phase transitions and key reactions (i.e., to 500 °C) that contribute to thermal runaway. This method can help quantify the complex reaction network in a full cell, thereby informing potential safety issues. Here, we used DSC heat flow data from a solid-state Li 0.43 CoO 2 +C+PVDF | LLZO | Li metal ACE sample and its components to quantify key factors affecting results. We focused on three areas: (1) ACE sample preparation and assembly in DSC pans, (2) DSC measurement parameters, and (3) heat flow analysis. Key points include the choice of component ratios (e.g., commercially relevant N:P capacity ratio), the importance of conductive carbon and binder, type of pan used, DSC ramp rate, and integration method used when dealing with broad and overlapping exothermic peaks. This work deepens the scientific basis and best practices for obtaining heat flow data from ACE samples for early-stage evaluation of solid-state and beyond battery safety.

25 ENERGY STORAGE↗

DOE OSTI2024

DASSH-F: Subchannel Based Thermal Analysis

The DASSH thermal analysis code is designed to rapidly allow a reactor design engineer to obtain flow rates requirements that satisfy peak temperature constraints in the domain. The advantage of using DASSH over a hand calculation is that it has a more rigorous treatment of the pin power distribution and coolant heat transfer within an assembly and between assemblies. The advantage of using DASSH over a conventional 3D subchannel code or a computational fluid dynamics code (CFD) is that it can obtain the desired solution in a matter of minutes in serial with minor computer memory needs. The DASSH methodology is virtually identical to SUPERENERGY-2 with additional functionalities taken from follow on work to SUPERENERGY-2 done at ANL in the 1980s. DASSH today is an integral component of the Argonne Fast Reactor analysis suite for reactor design work. DASSH obtains the power distribution from a coupled neutron-gamma heating calculation in GAMSOR (including DIF3D) at each time point of a companion fuel cycle analysis calculation with REBUS. The domain in DASSH assumes a hexagonal grid typical for fast reactors with much of the geometry information taken from the DIF3D model. DASSH assumes the assemblies that are loaded into each grid position are ducted to control the coolant flow. Considerable detail is given on the subchannel formulation of DASSH in this document. Much of the formulation and design of the code builds upon research done by previous authors with little new investigation. Thus the decisions made in developing the subchannel model used in DASSH have their origins over 50 years ago. Much of the heat transfer methodology in DASSH is built upon correlations for both the coolant mixing and heat transfer coefficients for pins and ducts. DASSH is thus not a rigorous treatment of a given problem, but a rapid assessment of the temperature field that has known limitations with respect to an experimental measurement or CFD calculation. The DASSH input and output are detailed along with usage of the software. The DASSH output provides tables of evaluated material properties and key coolant and pin temperature results. DASSH can create Python scripts that generate domain summary pictures. DASSH can also generate assembly temperature maps and VTK output files which allow the DASSH solution to be visualized. As the primary purpose of the DASSH software is to compute the coolant and fuel pin temperature distribution for a given model of a reactor, much of the output focus is giving the user quick summary tables needed to assess the performance of a given orifice flow specification. The present version of DASSH has a crude orifice search capability and an efficient orifice flow search capability. The flow search tries to meet user specified constraints for 1) peak 2-sigma clad midwall temperature, 2) peak coolant temperature, and 3) desired bulk outlet temperature. There are many development shortcomings in DASSH detailed in this document, but this version is functional for modern analysis needs. This document serves as the manual for the Fortran based DASSH software that was developed to replace the Python version of DASSH developed as part of the VTR program.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2026

DASSH-F: Subchannel Based Thermal Analysis

The DASSH thermal analysis code is designed to rapidly allow a reactor design engineer to obtain flow rates requirements that satisfy peak temperature constraints in the domain. The advantage of using DASSH over a hand calculation is that it has a more rigorous treatment of the pin power distribution and coolant heat transfer within an assembly and between assemblies. The advantage of using DASSH over a conventional 3D subchannel code or a computational fluid dynamics code (CFD) is that it can obtain the desired solution in a matter of minutes in serial with minor computer memory needs. The DASSH methodology for pin lattice models is virtually identical to SUPERENERGY-2 with additional functionalities taken from follow on work to SUPERENERGY-2 done at ANL in the 1980s. DASSH today is an integral component of the Argonne Fast Reactor analysis suite for reactor design work. DASSH obtains the power distribution from a coupled neutron-gamma heating calculation in GAMSOR (including DIF3D) at each time point of a companion fuel cycle analysis calculation with REBUS. The domain in DASSH assumes a hexagonal grid typical for fast reactors with much of the geometry information taken from the DIF3D model. DASSH assumes the assemblies that are loaded into each grid position are ducted to control the coolant flow. The user can alternatively provide their own geometry and power profile instead of inheriting it from DIF3D. Considerable detail is given on the subchannel formulation of DASSH in this document. Much of the formulation and design of the code builds upon research done by previous authors with little new investigation. Thus the decisions made in developing the subchannel model used in DASSH have their origins over 50 years ago. Much of the heat transfer methodology in DASSH is built upon correlations for both the coolant mixing and heat transfer coefficients for pins and ducts. DASSH is thus not a rigorous treatment of a given problem, but a rapid assessment of the temperature field that has known limitations with respect to an experimental measurement or CFD calculation. The DASSH input and output are detailed along with usage of the software. The DASSH output provides tables of evaluated material properties and key coolant and pin temperature results. DASSH can create Python scripts that generate domain summary pictures. DASSH can also generate assembly temperature maps and VTK output files which allow the DASSH solution to be visualized. As the primary purpose of the DASSH software is to compute the coolant and fuel pin temperature distribution for a given model of a reactor, much of the output focus is giving the user quick summary tables needed to assess the performance of a given orifice flow specification. The present version of DASSH has a crude orifice search capability and a sufficient orifice flow search capability. The flow search tries to meet user specified constraints for 1) peak 2-sigma clad temperature, 2) peak coolant temperature, and 3) desired bulk outlet temperature. This document serves as the manual for the Fortran based DASSH software that was developed to replace the Python version of DASSH developed as part of the VTR program.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Flow instabilities in helical-coil steam generators for small modular reactors: A review

Here, this study covers the research and discoveries in two-phase flow-boiling instabilities available in the literature—specifically for a helical-coil steam generator (HCSG), including experimental findings, theoretical research, computational models, and system code analyses—supporting research and development of representative small modular reactors (SMRs). Like other new and advanced reactor systems, water-cooled SMRs require experimental data from both integral and separate thermal-hydraulics test facilities for the verification and validation (V&V) of the computational models and computer codes in order to design and obtain regulatory approval. The complex dynamics of two-phase flow-boiling instabilities includes flow regimes physics phenomena, flow-channel geometries, heat-transfer behavior, and interactions among the solid–liquid-gas within the system boundary, all of which are pivotal for understanding the design and operational challenges of SMRs. This study focuses on identifying the relevant knowledge gaps on boiling instabilities—specifically for a HCSG—and provides insights about future research direction optimizing the transport of thermal energy, mass-flow rates, and boundary conditions that ensure the adequate heat-transfer performance, operational stability, and safety associated with SMR systems.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2026

Jet charge with global event shapes: Probing quark flavor dynamics

We propose measuring the jet electric charge of jet regions, defined within the framework of global event shapes, as a probe of quark flavor dynamics within the nucleon and the hadronization process. In particular, we consider a measurement of the jet region charge while simultaneously keeping track of the energy flow throughout the event, as characterized by the global event shape. As a concrete example, we focus on the measurement of the (Q), the jet charge of the jet region (𝐽) defined within the framework of the 1-Jettiness global event shape (𝜏 1 ) for the Deep Inelastic Scattering (DIS) process, 𝑒 − +𝑝→𝑒 − +𝐽+𝑋, with unpolarized or longitudinally polarized protons. The 1-Jettiness distribution, binned according to jet charge, allows for enhanced quark flavor separation of the initial state unpolarized or polarized PDFs. On the other hand, the jet charge distribution binned by 1-Jettiness can serve as a probe of quark flavor dynamics in the final state hadronization process. We derive a factorization theorem for simultaneous measurements of 𝜏 1 and Q in the resummation region, 𝜏 1 ≪𝑃 𝐽 𝑇 , where 𝑃 𝐽 𝑇 denotes the transverse momentum of the jet region. The correlation between the jet region charge and the charge of the struck quark is expected to be the strongest in the resummation region. The factorization theorem contains a new universal , generalizing the standard jet function to include a jet charge measurement. Therefore these universal functions can be extracted from a global analysis of N-jettiness and thrust at 𝑒 + ⁢𝑒 − colliders. We provide simulation studies to demonstrate the sensitivity of the 1-Jettiness jet charge observable to quark flavor dynamics in nucleon structure and explore the possibility of probing the final state hadronization process. This observable is well-suited for applications with existing HERA data and the future Electron-Ion Collider (EIC).

Mantry, Sonny [University of North Georgia, Dahlon↗

DOE OSTI2024

High-Fidelity and High-Performance Computational Simulations for Rapid Design Optimization of Sulfur Thermal Energy Storage

Industrial process heating (IPH) accounts for approximately 70% of US manufacturing energy use and is primarily produced by fossil fuel combustion. Approximately 1500 TWht (approximately 60%) of IPH demand is in the temperature range of 100-300. Industrial applications in this temperature range include drying, hydrothermal processing, thermal enhanced oil recovery, food and beverage, bioethanol production, etc. Cost-effective thermal energy storage (TES) that increases the utilization of waste and renewable heat (solar, geothermal, etc.) could provide significant energy savings and reliable heat sources, decrease emissions, and increase US manufacturing competitiveness through reductions in fuel consumption. TES development has historically been dominated by technologies suitable for deployment with concentrating solar power (CSP). State-of-the-art thermal storage deployed commercially with power tower CSP plants uses a 60%/40% NaNO3/KNO3 molten salt and operates between temperatures of approximately 280 degrees Celsius and 570 degrees Celsius using a two-tank configuration. However, these nitrate salts are unsuitable for operation outside of this temperature range due to a high freezing point of approximately 220 degrees Celsius, and limits on high-temperature salt stability and corrosion resistance of containment alloys. Other materials being investigated for TES include those based on: (1) sensible energy storage (various molten salt compositions, inert solid particles, rocks or pebble beds, sulfur, water, concrete, graphite, etc.), (2) latent energy storage in materials that undergo solid-liquid phase change at relevant temperatures (organic materials for low-temperature applications, inorganic salts and/or metals for high-temperature applications), or (3) thermochemical energy storage (hydrides, hydroxides, carbonates, metal oxides, etc.). The application temperature and challenges pertaining to storage material and/or containment cost, energy density, long-term thermal and cyclic stability, and charge/discharge heat transfer effectiveness drive material selection for a given IPH or electricity generation application. Sulfur is a cheap commodity at $80/ton compared to $1100 - 1300/ton for conventional salts. When using a metric of storage cost per kWh, sulfur costs around 2-3 $/kWh. Previous sulfur TES development focused on high temperature (>600 degrees) concentrated solar power applications with sulfur encapsulated in pipes and flow of gaseous HTF (air) in the shell side. However, for lower-temperature IPH applications in the range of approximately 100-300 degrees Celsius Element 16 adopted a compact and scalable TES design with molten sulfur in the shell and HTF pipes submerged in the molten sulfur bath. The low-cost molten sulfur TES for dispatchable IPH has deployment potential for broad applications. The spatial and temporal evolution of the HTF and sulfur temperature is critical to the TES system performance, and thus detailed modeling can improve understanding of the performance and facilitate design improvements. Using high performance computing and computational fluid dynamics (CFD) a low-cost molten sulfur thermal energy storage (TES) system for industrial process heating (IPH) applications was developed. The unique challenges in CFD modeling of sulfur TES are the sharp property changes of sulfur relevant to the working temperatures. Above 159, liquid sulfur undergoes polymerization, and the viscosity of sulfur rapidly increases by several orders of magnitude between 159 degrees Celsius and 188 degrees Celsius, followed by a decrease in viscosity beyond 188 degrees Celsius due to thermal bound dissociation. In addition, various concentrations of H2S impurities can also modify sulfur viscosity. This numerical challenge is especially relevant to transient simulation of the sulfur TES charging and discharging processes as the extreme property variations limit the applicability of traditional heat transfer correlations. Transient CFD simulations including the temperature-dependent sulfur properties and geometric complexity of the TES design were used to predict the effect of natural convection during charging and discharging on the heat transfer process, sulfur temperature uniformity, charge/discharge rates, and performance of the storage devices. The CFD model was validated with experimental results for a full charge and discharge cycle. The work will show 3D and 2D simulation comparisons aimed to facilitate rapid design iterations and a machine learning based design optimization approach.

CFD↗

DOE OSTI2025

Zinc dendrite removal in a nickel-zinc battery with flow-through electrodes

The development and deployment of inexpensive energy storage technologies is critical to realizing a clean energy grid. Batteries are being used in this role, but there remains a need for research on systems that are designed specifically for stationary energy storage, with a focus on lowering the overall cost rather than prioritizing the system energy density, specific energy, and power output. Here, we report the development of ultra-thick (1 cm thick) electrodes with engineered flow channels and explore the variables determining how thick these electrodes can feasibly be. Our proof of concept cell, utilizing the alkaline Ni-Zn chemistry, shows stable cycling over the initial 60 cycles but still suffers from the common Zn dendrite growth at the anode. To extend the life of these systems we report our novel methodology to completely remove Zn dendrites by exploiting the flow-through nature of our electrode architecture.

Collins-Wildman, Daniel L↗

DOE OSTI2024

Dark matter raining on DUNE and other large volume detectors

Direct detection is a powerful means of searching for particle physics evidence of dark matter (DM) heavier than about a GeV with o(kiloton) volume, low-threshold detectors. In many scenarios, some fraction of the DM may be boosted to large velocities enhancing and generally modifying possible detection signatures. We investigate the scenario where 100% of the DM is boosted at the Earth due to new attractive long-range forces. This leads to two main improvements in detection capabilities: (1) the large boost allows for detectable signatures of DM well below a GeV at large-volume neutrino detectors, such as DUNE, Super-K, Hyper-K, and JUNO, as possible DM detectors, and (2) the flux at the Earth’s surface is enhanced by a focusing effect. In addition, the model leads to a significant anisotropy in the signal with the DM flowing dominantly vertically at the Earth’s surface instead of the typical approximately isotropic DM signal. We develop the theory behind this model and also calculate realistic constraints using a detailed GENIE simulation of the signal inside detectors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2024

Enhancing Network Anomaly Detection Using Graph Neural Networks

In the world of Internet of Things (IoT) networks, where devices are constantly communicating, keeping them secure from cyber threats is critical. This paper introduces a novel approach to detecting unusual and potentially harmful activities in these networks using graph neural networks (GNNs). We combine two specific types of GNNs-GraphSAGE and graph attention networks (GAT)-to create a model that understands and represents the behaviors and interactions in a network. GraphSAGE creates an embedding of network activities by examining local data interactions, while GAT directs the model's focus to the most critical interactions. By integrating these two methods in a single model that considers different types of interactions (both host and flow nodes), we aim to create a system that accurately represents the current state of a network and can also spot anomalies effectively while reducing false positives and negatives. Our innovative approach has demonstrated promising results, achieving an accuracy of 98% on the UNSW-NB15 dataset, significantly outperforming standalone GraphSAGE and GAT models. This underscores its potential as a robust framework for securing IoT networks against cyber threats and anomalies.

Marfo, William↗

DOE OSTI2024

CIRCLES: Congestion Impacts Reduction via CAV-in-the-loop Lagrangian Energy Smoothing

The energy efficiency of today’s vehicular mobility relies on the un-integrated combination of i) control via static assets (traffic lights, metering, variable speed limits, etc.); and ii) onboard vehicle automation (adaptive cruise control (ACC), ecodriving, etc.). These two families of control were not co-designed and are not engineered to work in coordination. Recent studies have shown i) limitations of controls, and even ii) negative impacts of ACC. This project focused on the technology development, implementation and prototyping, and validation of Mobile Traffic Control (MTC). MTC can be viewed as an extension of classical traffic control (in which static infrastructure actuates traffic flow). In the MTC paradigm, automated vehicles actuate the entire flow via their behavior, offering enhanced possibilities to optimize the energy footprint of traffic, if designed correctly. We set out to demonstrate for the first time that considerably reduced fuel consumption of all vehicles in traffic can be achieved via distributed control of a small proportion of CAVs. Compared to baseline vehicular technologies, our work offers a significant design departure: control algorithms for the CAVs consider the impact one vehicle can have on overall traffic, improving resulting overall fuel consumption. We focus on using a few vehicles (as traffic controllers via CAV technology) to improve the energy efficiency of traffic flow to further optimize energy efficiency. A live-traffic demonstration in November 2022 featured the deployment of 100 specially-equipped CAVs, constituting an approximate local penetration rate upwards of 2%.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Numerical simulation of frost formation and heat transfer on fin-and-tube heat exchangers in turbulent cross-flow

Frost formation in fin-and-tube heat exchangers in turbulent cross-flow presents significant challenges in industrial refrigeration applications, affecting heat transfer efficiency and operational reliability. The purpose of this work is to investigate frost deposition and growth on a staggered bank of a fin-and-tube freezer coil under turbulent forced convection conditions. The focus here is on investigating conditions that closely replicate real-world scenarios in large walk-in industrial freezers. Using a direct numerical simulation approach, we examine the flow dynamics and thermal behaviour in the presence of frost, considering turbulent regimes characterized by a Reynolds number in the range 1050 ≤ R e D , avg ≤ 4800 , with the characteristic length being the outer diameter of the tube and the velocity being the bulk fluid velocity between the plates (fins). Computational fluid dynamics simulations are employed to resolve the interactions between turbulent airflow and the frost layer. Our approach incorporates a modified immersed boundary method and a slow-time acceleration technique to address the complex dynamic interface between the continuously evolving frost layer and the flowing air stream. Our findings indicate that frost forms more on the sides of the finned surfaces (plates) and less on the tubes themselves. This article is part of the theme issue ‘Heat and mass transfer in frost and ice’.

Science & Technology - Other Topics↗