Search NASA⌕ Search

SEARCH · Search NASA

Results for “force margin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Optimization and mechanisms of mistuning in cascades

In the present inverse design procedure for the optimum mistuning of a high bypass ratio shroudless fan that is modeled as a cascade of blades (each with a single torsional degree-of-freedom), linearized supersonic aerodynamic theory is used to compute the unsteady aerodynamic forces in the 'influence coefficient' form at a typical blade section. The mistuning pattern is then numerically optimized in order to achieve a specified increase in the aeroelastic stability margin with a minimum amount of mistuning. If the blades are self-damped, an optimized mistuning pattern can be found that achieves a given stability margin for a much lower level of mistuning than required for the alternate mistuning pattern, which requires only two blade frequencies and is relatively insensitive to implementation errors.

Crawley, E. F.↗
NASA NTRS1987

A numerical study of flare stabilized projectiles at Mach 7.0

The effect of nose shape on two flare stabilized projectiles was studied using a Parabolized Navier-Stokes code. Pressure coefficients, forces and moments, skin friction coefficients, and Stanton number calculations are presented for the hemisphere-cylinder-flare and the cone-cylinder-flare configurations. Pitching moment and static margin plots versus flare angles and flare lengths are presented in a parametric study to show aerodynamic stability effects. Distinctly different flow field values of pressure, local Mach number, and dynamic pressure were generated by the two different nose configurations. These flow field values just upstream of the flare will be examined. The code demonstrated its value as a design tool by making a clear distinction between aerodynamically stable characteristics for this variety of nose shapes, flare angles, and flare lengths.

Hughson, Montgomery C.↗
NASA NTRS1997

A New 1000 F Magnetic Bearing Test Rig

NASA and the Army are currently exploring the possibility of using magnetic bearings in gas turbine engines. The use of magnetic bearings in gas turbine engines could increase the reliability by eliminating the lubrication system. The use of magnetic bearings could also increase the speed and the size of the shafts in the engine, thus reducing vibrations and possibly eliminating third bearings. Magnetic bearings can apply forces to the shafts and move them so that blade tips and seals do not rub. This could be part of an active vibration cancellation system. Also, whirling (displacing the shaft center line) may delay rotating stall and increase the stall margin of the engine. Magnetic bearings coupled with an integral starter generator could result in a more efficient 'more electric' engine. The IHPTET program, a joint DOD-industry program, has identified a need for a high temperature, (as high as 1200 F), magnetic bearing that could be demonstrated in a phase m engine. A magnetic bearing is similar to an electric motor. The magnetic bearing has a laminated rotor and stator made out of cobalt steel. The stator has a series of coils of wire wound around it. These coils f u. a series of electromagnets around the circumference. These magnets exert a force on the rotor to keep the rotor in the center of the cavity. The centering force is commanded by a controller based on shaft position, (measured by displacement probes). The magnetic bearing can only pull and is basically unstable before active control is applied The engine shafts, bearings, and case form a flexible structure which contain a large number of modes. A controller is necessary to stabilize these modes. A power amplifier is also necessary to provide the current prescribed by the controller to the magnetic bearings. In case of very high loads, a conventional back up bearing will engage and stop the rotor and stator from rubbing.

Kascak, Albert F.↗
NASA NTRS2002

Simulating Snow Over Sea Ice In Climate Models

We have evaluated two methods of simulating the seasonal cycle of snow over sea ice in and around the Arctic: The NCAR global climate model CCM3, with its standard snow hydrology, and the snow pack model SNTHERM, forced with hourly atmospheric output from CCM3. A new dataset providing dates for the onset of snow melt over Arctic sea ice provides a means for assessing basin-wide how well the models simulate melt onset, but contains no information on how long it then takes for all the snow to melt. Use of data from the SHEBA site provides very detailed information on the behavior of the snow before and during the melt season, but only for a very limited area. Russian drift data provide climatological data on the seasonal cycle of snow water equivalent and snow density, over multi-year sea ice in the central Arctic basin. These datasets are used to compare the two modeling methods, and to see if use of the more physically-realistic SNTHERM provides any significant improvements. Conclusions obtained so far include: 1. Both CCM3 and CCM3/SNTHERM do a good job overall of matching the onset of snow melt dataset; although CCM3/SNTHERM consistently trends to underestimate the date and CCM3 to overestimate it. 2. SHEBA and ice drift data for the Arctic show that CCM3/ SNTHERM does a better job than CCM3 at simulating the total melt period. 3. Ice drift snow density and accumulation data suggest that while providing superior results, CCM3/SNTHERM may still suffer from overly vigorous melting. 4. Both the large-scale atmospheric forcing and snow pack physical processes are important in proper simulation of the snow seasonal cycle. Ongoing work includes further diagnosis of CCM3/SNTHERM, use of more observational datasets, especially from marginal seas in the pan-Arctic, and full coupling of SNTHERM into CCM3 (work to date has all been off-line simulations).

Arnold, James E.↗
NASA NTRS1986

Reduced modeling of flexible structures for decentralized control

Based upon the modified finite element-transfer matrix method, this paper presents a technique for reduced modeling of flexible structures for decentralized control. The modeling decisions are carried out at (finite-) element level, and are dictated by control objectives. A simply supported beam with two sets of actuators and sensors (linear force actuator and linear position and velocity sensors) is considered for illustration. In this case, it is conjectured that the decentrally controlled closed loop system is guaranteed to be at least marginally stable.

Yousuff, A.↗
NASA NTRS1985

Active transition fixing and control of the boundary layer in air

Active transition of flow over an airfoil surface and feedback control by sound is investigated in a wind tunnel at Caltech. Laminar instability forced by localized time dependent nonintrusive narrow heating strip causes abrupt changes in velocity to trigger instant transition at favorable pressure gradient. At zero and adverse pressure gradients these changes are only marginal. Feedback control by sound interaction at nearly normal incidence produces significant reduction in velocity perturbation in regions of transition. This reduction is in part at the expense of an increase in background disturbance since it is not possible to restore the flow to its undisturbed state.

Maestrello, L.↗
NASA NTRS1988

Digital active control law synthesis for aeroservoelastic systems

This paper presents a formulation for synthesis of digital active control laws for aeroservoelastic systems, which are typically modeled by large order equations in order to accurately represent the rigid and flexible body modes, unsteady aerodynamic forces, actuator dynamics, and gust spectra. The control law is expected to satisfy multiple design requirements on the dynamic loads, responses, actuator deflection and rate limitations, as well as maintain certain stability margins, yet should be simple enough to be implemented by an onboard digital microprocessor. The synthesis procedure minimizes a linear quadratic Gaussian type cost function, by updating selected free parameters of the control law, while satisfying a set of inequality constraints on the design loads, responses and stability margins. A stable classical control law or an estimator based full or reduced order control law can be used as an initial design starting point. The gradients of the cost function and the constraints, with respect to the digital control law design variables are derived analytically, to facilitate rapid convergence. Selected design responses can be treated as constraints instead of lumping them into the cost function, in order to satisfy individual root-mean-square load and response limitations. Constraints are also imposed on the minimum singular value requirements for stability robustness improvement.

Mukhopadhyay, Vivekananda↗
NASA NTRS2008

Aeroheating Test of CEV Entry Vehicle at Turbulent Conditions

An investigation of the aeroheating environment of the Project Orion Crew Entry Vehicle has been performed in the Arnold Engineering Development Center Tunnel 9. Data were measured on a approx. 3.5% scale model (0.1778m/7-inch diam.) of the vehicle using coaxial thermocouples in the Mach 8 and Mach 10 nozzles of Tunnel 9. Runs were performed at free stream Reynolds numbers of 1 106/ft to 20 10(exp 6)/ft in the Mach 10 nozzle and 8 10(exp 6)/ft to 48 10(exp 6)/ft in the Mach 8 nozzle. The test gas in Tunnel 9 is pure N2, which at these operating conditions remains un-dissociated and may be treated as a perfect gas. At these conditions, laminar, transitional, and turbulent flow was produced on the model at Mach 10, and transitional and turbulent conditions were produced on the model at Mach 8. The majority of runs were made on a clean, smooth-surface model configuration and a limited number of runs were made in which inserts with varying boundary-layer trips configurations were used to force the occurrence of transition. Laminar and turbulent predictions were generated for all wind tunnel test conditions and comparisons were performed with the data for the purpose of helping to define uncertainty margins for the computational method. Data from both the wind tunnel test and the computations are presented herein. Figure 1 shows a schematic of the thermocouple locations on the model and figures 2 and 3 show a photo and schematic of the AEDC Hypervelocity Tunnel 9. Figure 4 shows a typical grid used in the computations. From the comparisons shown in figures 5 through 8 it was concluded that for perfect-gas conditions, the computations could predict either fully-laminar or full-turbulent flow to within +/-10% of the experimental data. The experimental data showed that transition began on the leeside of the heatshield at a free stream Reynolds number of 9 10(exp 6)/ft in the Mach 10 nozzle and fully-developed turbulent flow was produced at 20 10(exp 6)/ft. In the Mach 8 nozzle, transition on the leeside of the heat-shield was observed for all test conditions, and full-developed turbulent flow occurred at a free stream Reynolds number of 18 10(exp 6)/ft. On the aftbody of the vehicle no evidence of turbulence was detected at Mach 10 conditions, and at Mach 8 conditions, transition appeared to begin on the windside of the aftbody at free stream Reynolds number of 18x10(exp 6)/ft with fully-developed turbulent flow occurring only at the highest test condition of 48x10(exp 6)/ft.

Hollis, Brian R.↗
NASA NTRS2015

The Iodine Satellite (iSat) Project Development Towards Critical Design Review

Despite the prevalence of small satellites in recent years, the systems flown to date have very limited propulsion capability. SmallSats are typically secondary payloads and have significant constraints for volume, mass, and power in addition to limitations on the use of hazardous propellants or stored energy. These constraints limit the options for SmallSat maneuverability. NASA's Space Technology Mission Directorate approved the iodine Satellite flight project for a rapid demonstration of iodine Hall thruster technology in a 12U (cubesat units) configuration under the Small Spacecraft Technology Program. The mission is a partnership between NASA MSFC, NASA GRC, and Busek Co, Inc., with the Air Force supporting the propulsion technology maturation. The team is working towards the critical design review in the final design and fabrication phase of the project. The current design shows positive technical performance margins in all areas. The iSat project is planned for launch readiness in the spring of 2017.

Dankanich, John W.↗
NASA NTRS2012

Compact, Low-Force, Low-Noise Linear Actuator

Actuators are critical to all the robotic and manipulation mechanisms that are used in current and future NASA missions, and are also needed for many other industrial, aeronautical, and space activities. There are many types of actuators that were designed to operate as linear or rotary motors, but there is still a need for low-force, low-noise linear actuators for specialized applications, and the disclosed mechanism addresses this need. A simpler implementation of a rotary actuator was developed where the end effector controls the motion of a brush for cleaning a thermal sensor. The mechanism uses a SMA (shape-memory alloy) wire for low force, and low noise. The linear implementation of the actuator incorporates a set of springs and mechanical hard-stops for resetting and fault tolerance to mechanical resistance. The actuator can be designed to work in a pull or push mode, or both. Depending on the volume envelope criteria, the actuator can be configured for scaling its volume down to 4 2 1 cm3. The actuator design has an inherent fault tolerance to mechanical resistance. The actuator has the flexibility of being designed for both linear and rotary motion. A specific configuration was designed and analyzed where fault-tolerant features have been implemented. In this configuration, an externally applied force larger than the design force does not damage the active components of the actuator. The actuator housing can be configured and produced using cost-effective methods such as injection molding, or alternatively, its components can be mounted directly on a small circuit board. The actuator is driven by a SMA -NiTi as a primary active element, and it requires energy on the order of 20 Ws(J) per cycle. Electrical connections to points A and B are used to apply electrical power in the resistive NiTi wire, causing a phase change that contracts the wire on the order of 5%. The actuation period is of the order of a second for generating the stroke, and 4 to 10 seconds for resetting. Thus, this design allows the actuator to work at a frequency of up to 0.1 Hz. The actuator does not make use of the whole range of motion of the SMA material, allowing for large margins on the mechanical parameters of the design. The efficiency of the actuator is of the order of 10%, including the margins. The average dissipated power while driving at full speed is of the order of 1 W, and can be scaled down linearly if the rate of cycling is reduced. This design produces an extremely quiet actuator; it can generate a force greater than 2 N and a stroke greater than 1 cm. The operational duration of SMA materials is of the order of millions of cycles with some reduced stroke over a wide temperature range up to 150 C.

Badescu, Mircea↗
NASA NTRS2012

Compact, Low-Force, Low-Noise Linear Actuator

Actuators are critical to all the robotic and manipulation mechanisms that are used in current and future NASA missions, and are also needed for many other industrial, aeronautical, and space activities. There are many types of actuators that were designed to operate as linear or rotary motors, but there is still a need for low-force, low-noise linear actuators for specialized applications, and the disclosed mechanism addresses this need. A simpler implementation of a rotary actuator was developed where the end effector controls the motion of a brush for cleaning a thermal sensor. The mechanism uses a SMA (shape-memory alloy) wire for low force, and low noise. The linear implementation of the actuator incorporates a set of springs and mechanical hard-stops for resetting and fault tolerance to mechanical resistance. The actuator can be designed to work in a pull or push mode, or both. Depending on the volume envelope criteria, the actuator can be configured for scaling its volume down to 4x2x1 cu cm. The actuator design has an inherent fault tolerance to mechanical resistance. The actuator has the flexibility of being designed for both linear and rotary motion. A specific configuration was designed and analyzed where fault-tolerant features have been implemented. In this configuration, an externally applied force larger than the design force does not damage the active components of the actuator. The actuator housing can be configured and produced using cost-effective methods such as injection molding, or alternatively, its components can be mounted directly on a small circuit board. The actuator is driven by a SMA -NiTi as a primary active element, and it requires energy on the order of 20 Ws(J) per cycle. Electrical connections to points A and B are used to apply electrical power in the resistive NiTi wire, causing a phase change that contracts the wire on the order of 5%. The actuation period is of the order of a second for generating the stroke, and 4 to 10 seconds for resetting. Thus, this design allows the actuator to work at a frequency of up to 0.1 Hz. The actuator does not make use of the whole range of motion of the SMA material, allowing for large margins on the mechanical parameters of the design. The efficiency of the actuator is of the order of 10%, including the margins. The average dissipated power while driving at full speed is of the order of 1 W, and can be scaled down linearly if the rate of cycling is reduced. This design produces an extremely quiet actuator; it can generate a force greater than 2 N and a stroke greater than 1 cm. The operational duration of SMA materials is of the order of millions of cycles with some reduced stroke over a wide temperature range up to 150 C.

Badescu, Mircea↗
NASA NTRS1983

A coupled ice-ocean model of upwelling in the marginal ice zone

A dynamical coupled ice-ocean numerical model for the marginal ice zone (MIZ) is suggested and used to study upwelling dynamics in the MIZ. The nonlinear sea ice model has a variable ice concentration and includes internal ice stress. The model is forced by stresses on the air/ocean and air/ice surfaces. The main coupling between the ice and the ocean is in the form of an interfacial stress on the ice/ocean interface. The ocean model is a linear reduced gravity model. The wind stress exerted by the atmosphere on the ocean is proportional to the fraction of open water, while the interfacial stress ice/ocean is proportional to the concentration of ice. A new mechanism for ice edge upwelling is suggested based on a geostrophic equilibrium solution for the sea ice medium. The upwelling reported in previous models invoking a stationary ice cover is shown to be replaced by a weak downwelling due to the ice motion. Most of the upwelling dynamics can be understood by analysis of the divergence of the across ice edge upper ocean transport. On the basis of numerical model, an analytical model is suggested that reproduces most of the upwelling dynamics of the more complex numerical model.

Roed, L. P.↗
NASA NTRS1984

Wind-tunnel free-flight investigation of a model of a forward-swept-wing fighter configuration

A wind-tunnel free-flight investigation was conducted to study the dynamic stability characteristics of a model of a forward-swept-wing fighter-airplane configuration at high angles of attack. Various other wind-tunnel techniques employed in the study included static- and dynamic- (forced-oscillation) force tests, free-to-roll tests, and flow-visualization tests. A unique facet of the study was the extreme level of static pitch instability (in excess of negative 32-percent static margin) inherent in the airframe design which precluded free-flight testing without stability augmentation in pitch. Results are presented which emphasize the high-angle-of-attack aerodynamics and the vehicle-component contributions to these characteristics. The effects of these aerodynamic characteristics on the high-angle-of-attack flying qualities of the configuration are discussed in terms of results of the wind-tunnel free-flight tests.

Murri, D. G.↗
NASA NTRS1974

Intrathoracic and venous pressure relationships during responses to changes in body position

Simultaneous end-expiratory pressures, referred to midthoracic level, in the superior and abdominal venae cavae, pericardial space, and right and left heart, were recorded without thoracotomy in three anesthetized dogs during sudden changes from supine to vertical head-up or head-down body positions. Intrathoracic and dependent great vein pressures referred to midchest level (sixth thoracic vertebra) decreased and showed simple hydrostatic gradients in either vertical position. However, a discontinuity in the large vein hydrostatic gradient occurred just distal to the superior margin of the thorax in either body position and was resumed again above this level. It is concluded that, just as the cerebrospinal fluid and intraperitoneal pressures minimize the effects of gravitational and inertial forces on the cerebral and visceral circulations, the pericardial and pleural pressures have a similar role for the heart proper.

Avasthey, P.↗
NASA NTRS1992

High-speed civil transport flight- and propulsion-control technological issues

Technology advances required in the flight and propulsion control system disciplines to develop a high speed civil transport (HSCT) are identified. The mission and requirements of the transport and major flight and propulsion control technology issues are discussed. Each issue is ranked and, for each issue, a plan for technology readiness is given. Certain features are unique and dominate control system design. These features include the high temperature environment, large flexible aircraft, control-configured empennage, minimizing control margins, and high availability and excellent maintainability. The failure to resolve most high-priority issues can prevent the transport from achieving its goals. The flow-time for hardware may require stimulus, since market forces may be insufficient to ensure timely production. Flight and propulsion control technology will contribute to takeoff gross weight reduction. Similar technology advances are necessary also to ensure flight safety for the transport. The certification basis of the HSCT must be negotiated between airplane manufacturers and government regulators. Efficient, quality design of the transport will require an integrated set of design tools that support the entire engineering design team.

Ray, J. K.↗
NASA NTRS2005

Chapter 9 - Pre-Flight Tests

Pre-flight testing is critical to the success of any flight test program. Pre-flight tests are performed to measure and evaluate the characteristics of an aircraft in a non-flying environment and to verify that these characteristics are as desired. Since aircraft systems are becoming more and more complex, conducting proper pre-flight testing to help identify system characteristics and deficiencies prior to flight is more important now than ever before. Much flight test time has been lost fixing problems that should have been found and corrected prior to flight. Accidents have occurred because pre-flight tests and verification procedures were not conducted thoroughly enough to identify the aircraft's characteristics properly or to find system discrepancies. Proper pre-flight testing helps ensure that the aircraft is ready to fly and contributes toward an efficient, productive, and safe flight test program. The reader should be aware that this Section is dedicated to the testing that should take place prior to the first flight. There are other "pre-flight" tests that take place prior to each individual flight. These latter tests are not discussed in this Section. The following paragraphs of this Section describe significant tests that are usually accomplished prior to flying a new or highly modified aircraft. Test objectives, descriptions, products, and requirements are provided in the following subsections: 9.1 Wind tunnel tests 9.2 Simulation tests 9.3 Propulsion tests 9.4 Weight and balance tests 9.5 Ground vibration tests 9.6 Structural loads tests 9.7 Gain margin tests 9.8 Verification and calibration tests 9.9 Taxi tests The specific examples given and the test facilities mentioned in this Section will illustrate the approach taken and the techniques used by the US Air Force; however, they are typical of those used by other test organizations.

Paul W Kirsten↗
NASA NTRS2023

Impact of Design Factors for ESA CCI Satellite Soil Moisture Data Assimilation over Europe

In this study, soil moisture retrievals of the combined active–passive ESA Climate Change Initiative (CCI) soil moisture product are assimilated into the Noah-MP land surface model over Europe using a one-dimensional ensemble Kalman filter and an 18-yr study period. The performance of the data assimilation (DA) system is evaluated by comparing it with a model-only experiment (at in situ sites) and by assessing statistics of innovations and increments as DA diagnostics (over the entire domain). For both assessments, we explore the impact of three design choices, resulting in the following insights. 1) The magnitude of the assumed observation errors strongly affects the skill improvements evaluated against in situ stations and internal diagnostics. 2) Choosing between climatological or monthly cumulative distribution function matching as the observation bias correction method only has a marginal effect on the in situ skill of the DA system. However, the internal diagnostics suggest a more robust system parameterization if the observations are rescaled monthly. 3) The choice of atmospheric reanalysis dataset to force the land surface model affects the model-only skill and the DA skill improvements. The model-only skill is higher with input from the MERRA-2 than with input from the ERA5 reanalysis, resulting in larger DA skill improvements for the latter. Additionally, we show that the added value of the DA strongly depends on the quality of the satellite retrievals and land cover, with the most substantial soil moisture skill improvements occurring over croplands and skill degradation occurring over densely forested areas.

Soil moisture↗
NASA NTRS2018

Cyclic Symmetry Finite Element Forced Response Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

Accurate prediction of the blade vibration stress is required to determine overall durability of fan blade design under Boundary Layer Ingestion (BLI) distorted flow environments. Traditional single blade modeling technique is incapable of representing accurate modeling for the entire rotor blade system subject to complex dynamic loading behaviors and vibrations in distorted flow conditions. A particular objective of our work was to develop a high-fidelity full-rotor aeromechanics analysis capability for a system subjected to a distorted inlet flow by applying cyclic symmetry finite element modeling methodology. This reduction modeling method allows computationally very efficient analysis using a small periodic section of the full rotor blade system. Experimental testing by the use of the 8-foot by 6-foot Supersonic Wind Tunnel Test facility at NASA Glenn Research Center was also carried out for the system designated as the Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan (BLI2DTF) technology development. The results obtained from the present numerical modeling technique were evaluated with those of the wind tunnel experimental test, toward establishing a computationally efficient aeromechanics analysis modeling tool facilitating for analyses of the full rotor blade systems subjected to a distorted inlet flow conditions. Fairly good correlations were achieved hence our computational modeling techniques were fully demonstrated. The analysis result showed that the safety margin requirement set in the BLI2DTF fan blade design provided a sufficient margin with respect to the operating speed range.

forced response analysis↗