Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Calculation of turbulent boundary layers with tangential slot injection

Paper describes a numerical calculation scheme for tangential slot injection (wall-wake) flows; application of the scheme over a wide range of flow conditions indicates increased accuracy compared to previous work. Predictions from the numerical code were in good agreement with experiment (velocity profile, skin-friction, and effectiveness data) for low- and high-speed flows. To achieve improved accuracy, modifications in the turbulence modeling, compared to previous research, were necessary for the imbedded shear layer region in the near field and for the wall region near shear layer impingement. Anomalous behavior was noted for far field experimental velocity profiles in low-speed flow when the slot-to-free stream velocity ratio was near one

Cary, A. M., Jr.↗
NASA NTRS1979

Diagnosis of separated flow regions on wind-tunnel models using an infrared camera

A novel technique utilizing an infrared-sensitive imaging camera has been used to determine the location of three-dimensional (3-D) separated flow regions on an inclined 5 deg semiangle fiberglass cone. The results illustrate that there is a change in the contrast of the infrared (IR) signature on the cone surface corresponding with the location where the skin-friction lines merge toward lines of 3-D separation. This technique should offer a convenient means for locating separated flow regions on wind-tunnel models while obtaining simultaneous force, skin-friction, and pressure data.

Bandettini, A.↗
NASA NTRS1982

Polyimides: Tribological properties and their use as lubricants

Friction, wear, and wear mechanisms of several different polyimide films, solid bodies, composites, and bonded solid lubricant films are compared and discussed. In addition, the effect of such parameters as temperatures, type of atmosphere, contact stress, and specimen configuration are investigated. A friction and wear transition occurs in some polyimides at elevated temperatures and this transition is related to molecular relaxations that occur in polyimides. Friction and wear data from an accelerated test (pin-on-disk) are compared to similar data from an end use test device (plain spherical bearing), and to other polymers investigated in a similar geometry.

Fusaro, R. L.↗
NASA NTRS1984

Polyimides - Tribological properties and their use as lubricants

Friction, wear, and wear mechanisms of several different polyimide films, solid bodies, composites, and bonded solid lubricant films are compared and discussed. In addition, the effect of such parameters as temperatures, type of atmosphere, contact stress, and specimen configuration are investigated. A friction and wear transition occurs in some polyimides at elevated temperatures and this transition is related to molecular relaxations that occur in polyimides. Friction and wear data from an accelerated test (pin-on-disk) are compared to similar data from an end use test device (plain spherical bearing), and to other polymers investigated in a similar geometry.

Fusaro, R. L.↗
NASA NTRS1986

Tribology of selected ceramics at temperatures to 900 C

Results of fundamental and focused research on the tribological properties of ceramics are discussed. The basic friction and wear characteristics are given for ceramics of interest for use in gas turbine, adiabatic diesel, and Stirling engine applications. The importance of metal oxides in ceramic/metal sliding combinations is illustrated. The formulation and tribological additives are described. Friction and wear data are given for carbide and oxide-based composite coatings for temperatures to at least 900 C.

Sliney, H. E.↗
NASA NTRS1960

Halogen Containing Gases as Lubricants for Crystallized Glass Ceramic Metal Combinations at Temperatures to 1500 F

Pyroceram 9608 (a crystallized glass ceramic) has been considered for use in high-temperature bearing and seal applications. One of the problems encountered with Pyroceram is the lack of availability of lubricants for the temperature range in which this material becomes practical. Experiments were conducted with Pyroceram sliding on various nickel- and cobalt-base alloys using reactive halogen-containing gases as lubricants. Friction and wear data were obtained as a function of sliding velocity and temperature. Studies were made with a hemispherical rider (3/16-in. rad., Pyroceram 9608) sliding in a circumferential path on the flat surface of a rotating disk (2(1/2) in. diam., nickel- or cobalt-base alloys). The specimens were run in an atmosphere of the various gases with a load of 1200 grams, a sliding velocity of 3200 feet per minute, and temperatures from 75 to 1500 F. The gas CF2Br-CF2Br was found to be an effective lubricant for Pyroceram 9608 sliding on Hastelloy R-235 and Inconel X up to 1400 F. The gas CF2Cl-CF2Cl provided effective lubrication for Pyroceram sliding on various cobalt-base alloys at 1000 F.

Buckley, Donald H.↗
NASA NTRS1992

Application of fiber bridging models to fatigue crack growth in unidirectional titanium matrix composites

Several fiber bridging models were reviewed and applied to study the matrix fatigue crack growth behavior in center notched (0)(sub 8) SCS-6/Ti-15-3 and (0)(sub 4) SCS-6/Ti-6Al-4V laminates. Observations revealed that fatigue damage consisted primarily of matrix cracks and fiber matrix interfacial failure in the (0)(sub 8) SCS-6/Ti-15-3 laminates. Fiber-matrix interface failure included fracture of the brittle reaction zone and cracking between the two carbon rich fiber coatings. Intact fibers in the wake of the matrix cracks reduce the stress intensity factor range. Thus, an applied stress intensity factor range is inappropriate to characterize matrix crack growth behavior. Fiber bridging models were used to determine the matrix stress intensity factor range in titanium metal matrix composites. In these models, the fibers in the wake of the crack are idealized as a closure pressure. An unknown constant frictional shear stress is assumed to act along the debond or slip length of the bridging fibers. The frictional shear stress was used as a curve fitting parameter to available data (crack growth data, crack opening displacement data, and debond length data). Large variations in the frictional shear stress required to fit the experimental data indicate that the fiber bridging models in their present form lack predictive capabilities. However, these models provide an efficient and relatively simple engineering method for conducting parametric studies of the matrix growth behavior based on constituent properties.

Bakuckas, J. G., Jr.↗
NASA NTRS1997

Friction Velocity Estimation Using Dual-Frequency Altimeter Data

Global estimation of wind speeds near the sea-surface can be obtained using normalized radar cross sections sigma(o) from satellite-borne single-frequency altimeters. Indeed recent validation studies of Geosat altimeter-derived wind speeds show that several often cited semiempirical algorithms yield linear trends between wind-speeds from altimeter data and wind speeds from (a) ships of opportunity (Etcheto 1992), (b) buoys (Carter 1992), and (c) atmospheric models (Guillaume 1992). Although the linear trends are striking, there is considerable scatter since the range of standard deviations is from 1.5 to 3 m/s. In fact, the scatter of some particular measurements about the regressions is striking because they depart from the 'standard' by as much as +/- 5 m/s, which is large - even for full gale winds of 20 m/s. These anomalies can cause serious problems for gas exchange, heat, and aerosol estimates. They can also induce considerable errors in wind-driven oceanic circulation models and sea-surface wave models. This paper explores the possibility of improving the accuracy of wind speed estimation using dual-frequency altimeters.

Bliven, Larry F.↗
NASA NTRS1996

Colors Of Liquid Crystals Used To Measure Surface Shear Stresses

Developmental method of mapping shear stresses on aerodynamic surfaces involves observation, at multiple viewing angles, of colors of liquid-crystal surface coats illuminated by white light. Report describing method referenced in "Liquid Crystals Indicate Directions Of Surface Shear Stresses" (ARC-13379). Resulting maps of surface shear stresses contain valuable data on magnitudes and directions of skin friction forces associated with surface flows; data used to refine mathematical models of aerodynamics for research and design purposes.

Reda, D. C.↗
NASA NTRS1992

High-Temperature Tribometer And Data-Acquisition System

New tribometer tests friction and wear properties of ceramic and metal materials at temperatures up to 1,200 degrees C in controlled atmospheres. Connected to data-acquisition system using computer programs to enhance productivity and convenience of testing facility. Friction and wear properties of new materials and lubricants ascertained accurately and conveniently. Information needed in development of materials for advanced aerospace and terrestrial applications.

Sliney, Harold E.↗
NASA NTRS1952

Experimental Investigation of Eccentricity Ratio, Friction, and Oil Flow of Short Journal Bearings

An experimental investigation was conducted to obtain performance data on bearings of length-diameter ratios of 1, 1/2, and 1/4 for comparison with theoretical curves. A 1.375-inch-diameter bearing was tested at speeds up to 6000 rpm and with unit loads from 0 to 900 pounds per square inch. Experimental data for eccentricity ratio and friction followed single lines when plotted against a theoretically derived capacity number, which is equal to Sommerfeld number times the square of the length-diameter ratio. The form of the capacity number indicates that under certain conditions the eccentricity ratio is theoretically independent of bearing diameter. A method of plotting oil flow data as a single line is shown. Methods are also discussed for approximating a maximum bearing temperature and evaluating the effect of deflection or misalignment on the eccentricity ratio at the ends of the bearings.

BEARINGS, SLEEVE↗
NASA NTRS1991

Airfoil Vibration Dampers program

The Airfoil Vibration Damper program has consisted of an analysis phase and a testing phase. During the analysis phase, a state-of-the-art computer code was developed, which can be used to guide designers in the placement and sizing of friction dampers. The use of this computer code was demonstrated by performing representative analyses on turbine blades from the High Pressure Oxidizer Turbopump (HPOTP) and High Pressure Fuel Turbopump (HPFTP) of the Space Shuttle Main Engine (SSME). The testing phase of the program consisted of performing friction damping tests on two different cantilever beams. Data from these tests provided an empirical check on the accuracy of the computer code developed in the analysis phase. Results of the analysis and testing showed that the computer code can accurately predict the performance of friction dampers. In addition, a valuable set of friction damping data was generated, which can be used to aid in the design of friction dampers, as well as provide benchmark test cases for future code developers.

Cook, Robert M.↗
NASA NTRS1990

Turbulence modeling for sharp-fin-induced shock wave/turbulent boundary-layer interactions

Solutions of the Reynolds averaged Navier-Stokes equations are presented and compared with a family of experimental results for the 3-D interaction of a sharp fin induced shock wave with a turbulent boundary layer. Several algebraic and two equation eddy viscosity turbulence models are employed. The computed results are compared with experimental surface pressure, skin friction, and yaw angle data as well as the overall size of the interaction. Although the major feature of the flow fields are correctly predicted, several discrepancies are noted. Namely, the maximum skin friction values are significantly underpredicted for the strongest interaction cases. These and other deficiencies are discussed.

Horstman, C. C.↗
NASA NTRS1993

Generic hypersonic vehicle performance model

An integrated computational model of a generic hypersonic vehicle was developed for the purpose of determining the vehicle's performance characteristics, which include the lift, drag, thrust, and moment acting on the vehicle at specified altitude, flight condition, and vehicular configuration. The lift, drag, thrust, and moment are developed for the body fixed coordinate system. These forces and moments arise from both aerodynamic and propulsive sources. SCRAMjet engine performance characteristics, such as fuel flow rate, can also be determined. The vehicle is assumed to be a lifting body with a single aerodynamic control surface. The body shape and control surface location are arbitrary and must be defined. The aerodynamics are calculated using either 2-dimensional Newtonian or modified Newtonian theory and approximate high-Mach-number Prandtl-Meyer expansion theory. Skin-friction drag was also accounted for. The skin-friction drag coefficient is a function of the freestream Mach number. The data for the skin-friction drag coefficient values were taken from NASA Technical Memorandum 102610. The modeling of the vehicle's SCRAMjet engine is based on quasi 1-dimensional gas dynamics for the engine diffuser, nozzle, and the combustor with heat addition. The engine has three variable inputs for control: the engine inlet diffuser area ratio, the total temperature rise through the combustor due to combustion of the fuel, and the engine internal expansion nozzle area ratio. The pressure distribution over the vehicle's lower aft body surface, which acts as an external nozzle, is calculated using a combination of quasi 1-dimensional gas dynamic theory and Newtonian or modified Newtonian theory. The exhaust plume shape is determined by matching the pressure inside the plume, calculated from the gas dynamic equations, with the freestream pressure, calculated from Newtonian or Modified Newtonian theory. In this manner, the pressure distribution along the vehicle after body expansion surface is then determined. The aerodynamic modeling, the engine modeling, and the exhaust plume analysis are described in more detail. A description of the computer code used to perform the above calculations is given and an input/output example is then given. The computer code is available on a Macintosh floppy disk.

Chavez, Frank R.↗
NASA NTRS1980

The photometric properties of brightest cluster galaxies. II - SIT and CCD surface photometry

Surface photometry of the first-ranked galaxy in 108 Abell clusters is presented. Galaxy structure, as parameterized by simple Hubble law models, is found to correlate with galaxy absolute magnitude and cluster structure. All the structure data support the dynamical friction evolution model. Twenty-eight percent of the galaxies have multiple component nuclei; the short lifetimes of such systems provide the best available evidence that ongoing evolution actually occurs. Average magnitude and structure evolution rates are derived from the data.

Hoessel, J. G.↗
NASA NTRS2000

Skin Friction and Transition Location Measurement on Supersonic Transport Models

Flow visualization techniques were used to obtain both qualitative and quantitative skin friction and transition location data in wind tunnel tests performed on two supersonic transport models at Mach 2.40. Oil-film interferometry was useful for verifying boundary layer transition, but careful monitoring of model surface temperatures and systematic examination of the effects of tunnel start-up and shutdown transients will be required to achieve high levels of accuracy for skin friction measurements. A more common technique, use of a subliming solid to reveal transition location, was employed to correct drag measurements to a standard condition of all-turbulent flow on the wing. These corrected data were then analyzed to determine the additional correction required to account for the effect of the boundary layer trip devices.

Kennelly, Robert A., Jr.↗
NASA NTRS1980

In-flight boundary-layer measurements on a hollow cylinder at a Mach number of 3.0

Skin temperatures, shear forces, surface static pressures, boundary layer pitot pressures, and boundary layer total temperatures were measured on the external surface of a hollow cylinder that was 3.04 meters long and 0.437 meter in diameter and was mounted beneath the fuselage of the YF-12A airplane. The data were obtained at a nominal free stream Mach number of 3.0 (a local Mach number of 2.9) and at wall to recovery temperature ratios of 0.66 to 0.91. The local Reynolds number had a nominal value of 4,300,000 per meter. Heat transfer coefficients and skin friction coefficients were derived from skin temperature time histories and shear force measurements, respectively. In addition, boundary layer velocity profiles were derived from pitot pressure measurements, and a Reynolds analogy factor was obtained from the heat transfer and skin friction measurements. The measured data are compared with several boundary layer prediction methods.

Quinn, R. D.↗