Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry investigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Computation of viscous transonic flow about a lifting airfoil

The viscous transonic flow about a stationary body in free air was numerically investigated. The geometry chosen was a symmetric NACA 64A010 airfoil at a freestream Mach number of 0.8, a Reynolds number of 4 million based on chord, and angles of attack of 0 and 2 degrees. These conditions were such that, at 2 degrees incidence unsteady periodic motion was calculated along the aft portion of the airfoil and in its wake. Although no unsteady measurements were made for the NACA 64A010 airfoil at these flow conditions, interpolated steady measurements of lift, drag, and surface static pressures compared favorably with corresponding computed time-averaged lift, drag, and surface static pressures.

Walitt, L.↗
NASA NTRS1979

Longitudinal aerodynamic characteristics of a vectored-engine-over-wing configuration at subsonic speeds

The Langley V/STOL tunnel was used to determine the effects of vectoring exhaust flow on the longitudinal aerodynamic characteristics of a vectored-engine-over-wing configuration. Vectoring was accomplished by blowing from over-wing-mounted engines over a variable trailing-edge flap. Effects of varying canard geometry and wing leading-edge geometry were investigated. Wind-tunnel data were obtained at a Mach number of 0.186 for an angle-of-attack range from -20 deg to 24 deg and engine nozzle pressure ratios from 1.0 (jet off) to approximately 3.75.

Leavitt, L. D.↗
NASA NTRS1979

Analysis of the three dimensional flow in a turbine scroll

The present analysis describes the three-dimensional compressible inviscid flow in the scroll and the vaneless nozzle of a radial inflow turbine. The solution to this flow field, which is further complicated by the geometrical shape of the boundaries, is obtained using the finite element method. Symmetric and nonsymmetric scroll cross sectional geometries are investigated to determine their effect on the general flow field and on the exit flow conditions.

Hamed, A.↗
NASA NTRS1982

On ultrasonic factors and fracture toughness

Recent experimental and theoretical studies on ultrasonics have shown that the scattering of elastic waves by material defects yields data which characterize crack properties, such as size and orientation, and also the mechanical properties of the given material. In the present study, elastodynamic fields due to the presence of a pair of inhomogeneities in a material of plate geometry are investigated by the method of equivalent inclusions. The stress amplitude change of the plates during the passage of plane time-harmonic waves is found, and the relation between fracture toughness and ultrasonic factors is determined. The approach used does not assume the existence of a sharp crack in the material.

Fu, L. S.↗
NASA NTRS1983

Explanation of the hypersonic longitudinal stability problem: Lessons learned

Inviscid and viscous CFD codes have been applied to a modified Space Shuttle orbiter geometry to investigate differences between preflight aerodynamic predictions and aerodynamic data from hypersonic reentry flight. Flow field solutions were obtained for wind tunnel conditions and flight conditions to assess Mach number, real-gas, and viscous effects on the reentry aerodynamics of the orbiter. Based on the CFD studies, a methodology model has been developed to (1) extrapolate wind tunnel data to flight conditions and (2) calculate a DCM for use with the Aerodynamic Design Data Book. Comparisons are made with selected flight data. Results of the study indicate that the differences between flight and pre-STS-1 predictions of hypersonic pitching moment are primarily due the to Mach number and real-gas effects.

Griffith, B. J.↗
NASA NTRS1984

An AOTV aeroheating and thermal protection study

The aerothermodynamics and thermal protection of aerobraking orbital transfer vehicles are studied with a view toward design methodology and technology requirements. A particular class of geometries is investigated: the ellipsoidally blunted raked-off elliptic cone. Discussed are the influence of various geometrical parameters on the trajectory and the heat flux as well as heating prediction methods ranging from an engineering correlation formula to computational solutions of the Navier-Stokes equations. Finite-rate catalytic thermal protection materials and gas radiation are considered. Estimates of the specific mass of possible thermal protection systems indicate that support structure is a large contributor to the aerobrake mass as compared with the thermal protection insulation itself. Sizing curves are included which enable the designer to estimate the size aerobrake required from heating considerations for different mass vehicles having aerobrakes of several specific masses.

Scott, C. D.↗
NASA NTRS1985

Experimental investigations on airfoils with different geometries in the domain of high angles of attack-flow separation

Wind tunnel tests were conducted on airfoil models in order to study the flow separation phenomena occurring for high angles of attack. Pressure distribution on wings of different geometries were measured. Results show that for three-dimensional airfoils layout and span lift play a role. Separation effects on airfoils with moderate extension are three-dimensional. The flow domains separated from the air foil must be treated three-dimensionally. The rolling-up of separated vortex layers increases with angle in intensity and induction effect and shows strong nonlinearities. Boundary layer material moves perpendicularly to the flow direction due to the pressure gradients at the airfoil; this has a stabilizing effect. The separation starts earlier with increasing pointed profiles.

Keil, J.↗
NASA NTRS1985

Contributions to the finite element solution of the fan noise radiation problem

The radiation of fan generated noise to the far field from a nacelle of realistic geometry is investigated using the finite element method. Several innovations have been introduced to minimize the computational requirements and create a highly efficient numerical scheme. The innovations include: (1) formulation of the problem in terms of velocity potential and density in such a way that no inlet mean flow velocity derivatives are required in the field equations, (2) the use of 'wave envelope' elements in an outer region permitting a grid much coarser than would be used for conventional finite elements, (3) the use of a mesh which deforms with an increase of forward flight speed so that mesh lines are always lines of constant phase and rays for a point source, permitting the use of wave envelope elements and simple boundary conditions for any case of forward velocity, (4) an efficient scheme for introducing the noise source via modal amplitude coefficients, and (5) the use of a frontal solution technique which for physically realistic problems drastically reduces the active storage requirements. The finite element scheme is outlined, as are the specific details of the innovations. Results are given for cases where comparable experimental data are available.

Eversman, W.↗
NASA NTRS1986

Heat transfer in shrouded rectangular cavities

Heat transfer with turbulent flow over shrouded rectangular cavities are numerically investigated. The geometry studied models flow through the clearance gap at the grooved tip of an axial turbine blade, where the blade rotates in close proximity to a stationary outer ring or shroud. The direction of relative shroud motion is always in opposition to the direction of the gas flow across the blade tip. Heat transfer characteristics and flow pattern in a cavity are found to be strongly influenced by the dimension of gap clearance, cavity geometry, and relative shroud movement.

Chyu, M. K.↗
NASA NTRS1987

Damage growth in composite laminates with interleaves

The influence of placing interleaves between fiber reinforced plies in multilayered composite laminates is investigated. The geometry of the composite is idealized as two dimensional, isotropic, linearly elastic media made of a damaged layer bonded between two half planes and separated by thin interleaves of low extensional and shear moduli. The damage in the layer is taken in the form of a symmetric crack perpendicular to the interface and may extend up to the interface. The case of an H-shaped crack in the form of a broken layer with delamination along the interface is also analyzed. The interleaves are modeled as distributed shear and tension springs. Fourier integral transform techniques are used to develop solutions in terms of singular integral equations. An asymptotic analysis of the integral equations based on Muskhelishvili's techniques reveals logarithmically singular axial stresses in the half plane at the crack tips for the broken layer. For the H shaped crack, similar singularities are found to exist in the axial stresses at the interface crack tips in the layer and the half plane. The solution of the equations is found numerically for the stresses and displacements by using the Hadamard's concept of direct differentiation of Cauchy integrals as well as Gaussian integration techniques.

Goree, James G.↗
NASA NTRS1986

Growth of lead tin telluride crystals in gels

Improved gels and several geometries were investigated for use in growing crystals. The use of lead sulfide test crystals proved workable, but it was impossible to obtain and maintain a sufficiently concentrated telluride ion solution to successfully grow lead telluride crystals. It appears that oxygen in the solution is capable of oxidizing the telluride ion up to tellurium metal. The method may still be successful, but only if precautions are taken to eliminate dissolved oxygen from the gels and aqueous solutions and to maintain a suitable concentration of telluride, Te(2)-(aq.).

Barber, Patrick G.↗
NASA NTRS1987

Resistive-heating instability of a compressible, force-free plasma

The thermal stability of a resistive, force-free plasma in a two-dimensional, slab geometry is investigated numerically. Linearly unstable modes that arise as an energetic consequence of Ohmic heating are examined in relation to the dynamic magnetic-tearing instability. Plasma compression is found to give rise to a set of unstable thermal modes not seen in previous incompressible studies. Such modes can occur in parameter regimes where no purely growing tearing mode exists.

Sparks, L.↗
NASA NTRS1987

Damage growth in composite laminates with interleaves

The influence of interleaves on the fracture behavior of laminated composites is investigated. The geometry of the composite consists of a cracked layer, bonded between two half-planes, which is separated by thin, low modulus, interleaves. The interleaves are modeled as uncoupled tension and shear springs. A stress analysis is carried out for a crack which may grow up to and spread along the interface. Integral transform techniques are used to develop the solution in terms of singular integral equations. An asymptotic analysis reveals logarithmic singularities in the critical stresses for the case of a broken layer. The equations are solved numerically and the effect of damage on critical stresses is studied. Initial results indicate that the interleaf gives a significant reduction in stresses in the adjacent regions and, if properly selected, should result in a more damage tolerant laminate.

Goree, James G.↗
NASA NTRS1990

Plasma puff initiation of high Coulomb transfer switches

The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for the azimuthally uniform surface flashover which initiates plasma-puff under wide range of fill gas pressure of Ar, He and N2. The optimal fill gas pressure for the azimuthally uniform plasma-puff was about 120 mTorr and 450 Torr for He and N2, and between 120 mTorr and 5 Torr for Ar. The inverse pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. It was also shown that the azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff was also discussed in comparison with the hypocycloidal pinch plasma-puff triggering. The main discharge of inverse pinch switch with plasma-focus driven plasma-puff trigger is found to be more azimuthally uniform than that with hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr.

Venable, D. D.↗
NASA NTRS1991

Solution of three-dimensional afterbody flow using reduced Navier-Stokes equations

The flow over afterbody geometries was investigated using the reduced Navier-Stokes (RNS) approximation. Both pressure velocity flux-split and composites velocity primitive variable formulations were considered. Pressure or pseudopotential relaxation procedures are combined with sparse matrix or coupled strongly implicit algorithms to form a three-dimensional solver for general non-orthogonal coordinates. Three-dimensional subsonic and transonic viscous/inviscid interacting flows were evaluated. Solutions with and without regions of recirculation were obtained.

Almahroos, H. M. H.↗
NASA NTRS1990

The University of Minnesota oscillating flow experiments

Hot-wire anemometry techniques used to document laminar-to-turbulent transition in oscillating flow are discussed, and two transition mechanisms proposed by Seume (1988) are reviewed. Reliable near-wall data, and the convergence of ensemble-averaged velocities and rms velocity fluctuations will aid in evaluating wall shear stresses and calculating various boundary-layer parameters. Special consideration was given to a detailed measurement program which documents transition at different axial positions for the space power research engine (SPRE) operating point. Future work on the effect of entry geometry and measurements of heat transfer are outlined. In order to better simulate flow conditions in actual Stirling engine heat exchangers, the effects of various inflow geometries are investigated. Once the hydrodynamic conditions in the test section are documented, a measurement program to assess the effect of flow oscillation on heat transfer will commence.

Friedman, G. T.↗
NASA NTRS1992

Application of Face-Gear Drives in Helicopter Transmissions

The use of face gears in helicopter transmissions was explored. A light-weight, split torque transmission design utilizing face gears was described. Face-gear design and geometry were investigated. Topics included tooth generation, limiting inner and outer radii, tooth contact analysis, contact ratio, gear eccentricity, and structural stiffness. Design charts were developed to determine minimum and maximum face-gear inner and outer radii. Analytical study of transmission error showed face-gear drives were relatively insensitive to gear misalignment, but tooth contact was affected by misalignment. A method of localizing bearing contact to compensate for misalignment was explored. The proper choice of shaft support stiffness enabled good load sharing in the split torque transmission design. Face-gear experimental studies were also included and the feasibility of face gears in high-speed, high-load applications such as helicopter transmissions was demonstrated.

Litvin, F. L.↗
NASA NTRS1992

Face-gear drives: Design, analysis, and testing for helicopter transmission applications

The use of face-gears in helicopter transmissions was explored. A light-weight, split-torque transmission design utilizing face-gears is described. Face-gear design and geometry were investigated. Topics included tooth generation, limiting inner and outer radii, tooth contact analysis, contact ratio, gear eccentricity, grinding, and structural stiffness. Design charts were developed to determine minimum and maximum face-gear inner and outer radii. An analytical study showed that the face-gear drive is relatively insensitive to gear misalignment with respect to transmission errors, but the tooth contact is affected by misalignment. A method of localizing the bearing contact to permit operation with misalignment was explored. Two new methods for grinding of the face-gear tooth surfaces were also investigated. The proper choice of shaft stiffness enabled good load sharing in the split-torque transmission design. Face-gear experimental studies were also conducted. These tests demonstrated the feasibility of face-gears in high-speed, high-load applications such as helicopter transmissions.

Litvin, F. L.↗