SEARCH · Search NASA

Results for “high aspect ratio wing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Preliminary design of composite wings for buckling, strength and displacement constraints

An unstiffened panel buckling constraint for balanced, symmetric laminated composites is included on the global design level in a mathematical programming structural optimization procedure for designing wing structures. Constraints are introduced by penalty functions, and Newton's method based on approximate second derivatives of the penalty terms is used as the search algorithm to obtain minimum-mass designs. Constraint approximations used during the optimization process contribute to the computational efficiency of the procedure. A criterion is developed that identifies the appropriate conservative form of the constraint approximations that are used with the optimization procedure. Minimum-mass design results are obtained for a multispar high-aspect-ratio wing subjected to material strength, minimum-gage, displacement, panel buckling and twist constraints. The material systems considered for the examples are all graphite-epoxy, graphite-epoxy with boron-epoxy spar caps, and all aluminum. The composite material designs are shown to have an advantage over the aluminum designs since they can often satisfy additional constraints with only small mass increases.

Starnes, J. H., Jr.↗

DOE OSTI2020

Assessment of Low-Altitude Atmospheric Turbulence Models for Aircraft Aeroelasticity

We investigate the dynamic aeroelastic response of large but slow aircraft in low-altitude atmospheric turbulence. To this end, three turbulence models of increasing fidelity, namely, the one-dimensional von Kármán model, the two-dimensional Kaimal model and full three-dimensional wind fields extracted from large-eddy simulations (LES) are used to simulate ambient turbulence near the ground. Load calculations and flight trajectory predictions are conducted for a representative high-aspect-ratio wing aircraft, using a fully coupled nonlinear flight dynamics/aeroelastic model, when it operates in background atmospheric turbulence generated by the aforementioned models. Comparison of load envelopes and spectral content, on vehicles of varying flexibility, shows strong dependency between the selected turbulence model and aircraft aeroelastic response (e.g. 58% difference in the predicted magnitude of the wing root bending moment between LES and von Kármán models). This is mainly due to the presence of large flow structures at low altitudes that have comparable dimensions to the vehicle, and which despite the relatively small wind speeds within the Earth boundary layer, result in overall high load events for slow-moving vehicles. Results show that one-dimensional models that do not capture those effects provide fairly non-conservative load estimates and are unsuitable for very flexible airframe design.

atmospheric turbulence↗

NASA NTRS1992

Adaptive aeroelastic composite wings - Control and optimization issues

High-performance aircraft are adaptive machines composed of internal structural skeletons to which are attached control surfaces operated by hydraulic muscles to allow them to maneuver. The flight crew, avionic sensors and systems function as the brain and nervous system to adapt the machine to changing flight conditions, such as take-off, cruise and landing. The development of new materials that can expand or contract on command or change stiffness on demand will blur the now distinct boundaries between the structure, actuators and the control system. This paper discusses the use of imbedded active piezoelectric materials to change the aeroelastic stiffness of a lifting surface to allow this surface to control the aircraft. Expressions are developed for the piezoelectric material effectiveness when these active materials are combined with advanced composite structural materials for a swept, high-aspect-ratio wing. The interaction between advanced composite material properties and piezoelectric electromechanical properties is examined. The importance of choosing the proper active control laws is also illustrated.

Weisshaar, Terrence A.↗

NASA NTRS2022

Comparison of Computational Predictions of the Mach 0.80 Transonic Truss-Braced Wing Configuration with Experimental Data

The NASA Langley and Ames Research Centers have teamed together for comparisons of computational predictions of the Boeing Mach 0.80Transonic Truss-Braced Wing (TTBW) configuration with a high-speed experimental dataset. The Mach 0.80 TTBW vehicle is a high wing, high aspect ratio configuration, designed for a high lift-to-drag ratio. System studies have predicted significant fuel burn and emissions benefits with the TTBW technology moving toward meeting NASA Subsonic Transport Systems-Level-Metrics. A 4.5% scale Mach 0.80 design TTBW model was recently tested at the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel(11-Ft TWT),providing a valuable dataset to validate computational tools and investigate best practices as risk reduction efforts continue for the development of the advanced TTBW vehicle. The NASA Computational Fluid Dynamics (CFD) team has computed free-air flow solutions on the Mach 0.80 design flight configuration and two wind tunnel configuration variants using the USM3D and LAVA flow solvers. Accurate modeling of the configuration tested in the wind tunnel environment is critical to validating the CFD tools, thus the team has included the internal cavity region and sting in their modeling of the configuration, similar to that tested in the 11-Ft TWT. Overall, the CFD simulations compared well and show similar trends as the corrected experimental data for lift and drag polars. The CFD predicted lift curve is shifted in angle of attack from what was observed in the experiment. The shift in lift also was seen in the pitching moment comparison plots. CFD solutions were computed at constant CL test point values and showed overall very good agreement when comparing constant spanwise cuts of pressure coefficient data on the wing and strut with experimental data. CFD cavity corrections were also investigated using the 11-Ft TWT cavity correction method, similar to that used to correct the wind tunnel data. Results showed some improvement in pitching moment coefficient predictions, and an increase in drag, shifting the data to the right in drag polars, further from the experimental data at lower lift conditions, good agreement near the design CL, and slight improvement at the higher lift conditions.

Transonic Truss-Braced Wing↗

NASA NTRS1975

Application of active controls technology to the NASA Jet Star airplane

The feasibility was studied of modifying a Jet Star airplane into a demonstrator of benefits to be achieved from incorporating active control concepts in the preliminary design of transport type aircraft. Substantial benefits are shown in terms of fuel economy and community noise by virtue of reduction in induced drag through use of a high aspect ratio wing which is made possible by a gust alleviation system. An intermediate configuration was defined which helps to isolate the benefits produced by active controls technology from those due to other configuration variables. Also, an alternate configuration which incorporated composite structures, but not active controls technology, was defined in order to compare the benefits of composite structures with those of active controls technology.

Lange, R. H.↗

NASA NTRS1975

Design definition study of NASA/Navy lift/cruise fan V/STOL aircraft. Volume 1: Summary report of Navy multimission aircraft

This report presents results of a study by the Rockwell International Corporation for the NASA Ames Research Center and the Naval Air Systems Command of promising Navy lift-cruise fan V/STOL aircraft for the 1980-1985 time period. The purpose of the study was to identify the likely technical and operating characteristics and technology requirements for the ultimate development of this type aircraft. The study focused on identifying aircraft individually optimized to perform the anti-submarine warfare, carrier onboard delivery, combat search and rescue, surveillance and surface attack missions, and a multi-purpose aircraft concept capable of performing all five missions at minimum total program cost. The configuration features the use of two 1.3 fan pressure ratio, single stage lift-cruise fans and three current design J97 gas generators with a high mounted high aspect ratio wing with winglets. The design missions can be performed at takeoff weights ranging from approximately 32,000 to 39,000 pounds. Top speed is 0.80 Mach number at sea level and 0.885 at altitude, Advanced composite structural technology and advanced subsystem concepts are employed. One basic fuselage design, with alternate bolt-in floor structures, meets all the mission requirements.

Robert L Cavage↗

NASA NTRS1976

Energy and Economic Trade Offs for Advanced Technology Subsonic Aircraft

Changes in future aircraft technology which conserve energy are studied, along with the effect of these changes on economic performance. Among the new technologies considered are laminar-flow control, composite materials with and without laminar-flow control, and advanced airfoils. Aircraft design features studied include high-aspect-ratio wings, thickness ratio, and range. Engine technology is held constant at the JT9D level. It is concluded that wing aspect ratios of future aircraft are likely to significantly increase as a result of new technology and the push of higher fuel prices. Composite materials may raise aspect radio to about 11 to 12 and practical laminar flow-control systems may further increase aspect ratio to 14 or more. Advanced technology provides significant reductions in aircraft take-off gross weight, energy consumption, and direct operating cost.

Maddalon, D. V.↗

NASA NTRS1976

Study of an ACT demonstrator with substantial performance improvements using a redesigned JetStar

The feasibility was studied of modifying a JetStar airplane into a demonstrator of benefits to be achieved from incorporating active control concepts in the preliminary design of transport type aircraft. Substantial benefits are shown in terms of fuel economy and community noise by virtue of reduction in induced drag through use of a high aspect ratio wing which is made possible by a gust alleviation system. An intermediate configuration was defined which helps to isolate the benefits produced by active controls technology from those due to other configuration variables.

Lange, R. H.↗

NASA NTRS1976

Energy and economic trade offs for advanced technology subsonic aircraft

Changes in future aircraft technology which conserve energy are studied, along with the effect of these changes on economic performance. Among the new technologies considered are laminar-flow control, composite materials with and without laminar-flow control, and advanced airfoils. Aircraft design features studied include high-aspect-ratio wings, thickness ratio, and range. Engine technology is held constant at the JT9D level. It is concluded that wing aspect ratios of future aircraft are likely to significantly increase as a result of new technology and the push of higher fuel prices. Whereas current airplanes have been designed for AR = 7, supercritical technology and much higher fuel prices will drive aspect ratio to the AR = 9-10 range. Composite materials may raise aspect ratio to about 11-12 and practical laminar flow-control systems may further increase aspect ratio to 14 or more. Advanced technology provides significant reductions in aircraft take-off gross weight, energy consumption, and direct operating cost.

Maddalon, D. V.↗

NASA NTRS1979

Technology for future air transports

The requirements and opportunities for technological development in transport aircraft of the next generation are reviewed, focusing primarily on conventional, subsonic aircraft. Advances in computational aerodynamics and computer-aided design and manufacturing (in numerically controlled processes) are noted as well as improved wind tunnel testing and drag reduction techniques. Advances in aeroelasticity prediction have made it possible to use flexible, high-aspect-ratio wings without large weight penalties. Weight reduction may be achieved by the use of composite aircraft structures and superplastic forming combined with diffusion bonding, however composites require improvement in manufacturing techniques and mechanical properties in order to gain general acceptance. Propulsion systems can be improved in engine fuel efficiency, control, durability, environmental compatibility (exhaust and noise emissions), and fuel specifications. In avionics, due to the growth of low-cost, miniaturized packages, opportunities exist in the fields of digital controls, navigation, guidance and communication. Applications of new technologies to various aspects of flight safety are also outlined.

Klineberg, J. M.↗

NASA NTRS1982

Means for controlling aerodynamically induced twist

A control mechanism which provides active compensation for aerodynamically induced twist deformation of high aspect ratio wings consists of a torque tube, internal to each wing and rigidly attached near the tip of each wing, which is moved by an actuator located in the aircraft fuselage. As changes in the aerodynamic loads on the wings occur the torque tube is rotated to compensate for the induced wing twist.

Elber, W.↗

NASA NTRS1984

Some experiences in aircraft aeroelastic design using Preliminary Aeroelastic Design of Structures (PAD)

The design experience associated with a benchmark aeroelastic design of an out of production transport aircraft is discussed. Current work being performed on a high aspect ratio wing design is reported. The Preliminary Aeroelastic Design of Structures (PADS) system is briefly summarized and some operational aspects of generating the design in an automated aeroelastic design environment are discussed.

Radovcich, N. A.↗

NASA NTRS1990

Subsonic and transonic low-Reynolds-number airfoils with reduced pitching moments

A subsonic and a transonic airfoil are presented for application in a high-altitude long-endurance aircraft and a very-high-altitude aircraft, respectively. The subsonic airfoil is designed for a lift coefficient c(l) = 1.4 at a chord Reynolds number Re = 700,000 and a very low Mach number. The transonic airfoil is designed for c(l) = 1.0 at Re = 500,000 and a transonic Mach number M = 0.7. Both airfoils are developed to perform as well or better than previously designed airfoils. However, the present airfoils are developed for a constrained pitching moment to reduce aircraft trim drag and to relieve, to some extent, the torsional loads in the typically high-aspect-ratio wings. The beneficial effects of a cruise flap and of boundary-layer transition control on the off-design performance characteristics are illustrated.

Van Dam, C. P.↗

NASA NTRS1993

Design of an airborne launch vehicle for an air launched space booster

A conceptual design is presented for a carrier vehicle for an air launched space booster. This airplane is capable of carrying a 500,000 pound satellite launch system to an altitude over 40,000 feet for launch. The airplane features a twin fuselage configuration for improved payload and landing gear integration, a high aspect ratio wing for maneuverability at altitude, and is powered by six General Electric GE-90 engines. The analysis methods used and the systems employed in the airplane are discussed. Launch costs are expected to be competitive with existing launch systems.

Chao, Chin↗

NASA NTRS2004

Modeling and Design Analysis Methodology for Tailoring of Aircraft Structures with Composites

Composite materials provide design flexibility in that fiber placement and orientation can be specified and a variety of material forms and manufacturing processes are available. It is possible, therefore, to 'tailor' the structure to a high degree in order to meet specific design requirements in an optimum manner. Common industrial practices, however, have limited the choices designers make. One of the reasons for this is that there is a dearth of conceptual/preliminary design analysis tools specifically devoted to identifying structural concepts for composite airframe structures. Large scale finite element simulations are not suitable for such purposes. The present project has been devoted to creating modeling and design analysis methodology for use in the tailoring process of aircraft structures. Emphasis has been given to creating bend-twist elastic coupling in high aspect ratio wings or other lifting surfaces. The direction of our work was in concert with the overall NASA effort Twenty- First Century Aircraft Technology (TCAT). A multi-disciplinary team was assembled by Dr. Damodar Ambur to work on wing technology, which included our project.

Rehfield, Lawrence W.↗

NASA NTRS2013

Status of Advanced Stitched Unitized Composite Aircraft Structures

NASA has created the Environmentally Responsible Aviation (ERA) Project to explore and document the feasibility, benefits and technical risk of advanced vehicle configurations and enabling technologies that will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations that have higher lift-to-drag ratios, reduced drag, and lower community noise levels. The primary structural concept being developed under the ERA project in the Airframe Technology element is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. This paper describes how researchers at NASA and The Boeing Company are working together to develop fundamental PRSEUS technologies that could someday be implemented on a transport size aircraft with high aspect ratio wings or unconventional shapes such as a hybrid wing body airplane design.

Jegley, Dawn C.↗

NASA NTRS2017

Comparison of Theodorsen's Unsteady Aerodynamic Forces with Doublet Lattice Generalized Aerodynamic Forces

This paper identifies the unsteady aerodynamic forces and moments for a typical section contained in the NACA Report No. 496, "General Theory of Aerodynamic Instability and the Mechanism of Flutter," by Theodore Theodorsen. These quantities are named Theodorsen's aerodynamic forces (TAFs). The TAFs are compared to the generalized aerodynamic forces (GAFs) for a very high aspect ratio wing (AR = 20) at zero Mach number computed by the doublet lattice method. Agreement between TAFs and GAFs is very-good-to-excellent. The paper also reveals that simple proportionality relationships that are known to exist between the real parts of some GAFs and the imaginary parts of others also hold for the real and imaginary parts of the corresponding TAFs.

Perry, Boyd, III↗

NASA NTRSDate not supplied

Establishing Electrified Aircraft Propulsion Concepts—How AATT identified viable propulsion concepts and established foundational technologies

In the mid 2000’s NASA challenged the aeronautics industry to identify the routes for achieving ambitious improvements in fuel burn, emission, and noise reductions. These so-called “N+3” studies were exploring broad changes three commercial aircraft generations, or nominally 30 years, in the future. Many intriguing propulsion-airframe integrated solutions were proposed and pursued, which incorporated technologies such as high-aspect-ratio wings, boundary-layer ingestion, and hybrid-electric powertrains. When the Advanced Air Transport Technology (AATT) Project introduced “Technical Challenge 5.2-Establish viable concept for 5-10 MW hybrid gas-electric propulsion system for a commercial transport aircraft” in 2014, industry was very skeptical that electrified propulsion could make a significant impact in commercial air transport over the subsequent 30 years. Yet there were many practical reasons why improvements in electric power system and electric powertrains were advancing at a rapid rate and could lead to paradigm changes in aircraft propulsion. The challenge to the aeronautics community was to discover how to harness this power revolution and apply it to aircraft propulsion. This talk summarizes the approaches and achievements from the Hybrid Gas-Electric Propulsion Concept Technical Challenge that concluded in 2019. The balanced portfolio of concepts studies anchored with practical technology development demonstrated that electrified aircraft propulsion is an aircraft revolution whose time has come.

electric propulsion↗