SEARCH · Search NASA

Results for “high-frequency data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Cryogenic-Refined MOSFET Modeling for Oscillator, Frequency Divider, and Amplifier Designs Below 4 K

Capturing device characteristic changes at cryogenic temperatures is crucial for cryo-CMOS circuit designs. In this work, we present an isothermal cryogenic-refined modeling approach for CMOS transistors that is simple, low overhead, and easy to implement while offering the required accuracy for predicting circuit performance at the designated temperatures. Guided by die-level measurement data and circuit design principles, the model introduces corrections to only five critical parameters: threshold voltage, carrier mobility, elevated low-frequency flicker noise, dominant high-frequency shot noise, and subthreshold swing (SS). These refinements are implemented around the foundry-provided SPICE model, which is typically validated only down to about 200 K. With these adjustments, the proposed cryogenic-refined model achieves less than 5% error in both large-signal metrics (I–V characteristics) and small-signal parameters (e.g., transconductance) when compared with device measurements at deep-cryogenic temperatures. The methodology is validated in two advanced technologies: TSMC 40-nm CMOS and GlobalFoundries (GF) 45-nm RF-SOI. We further demonstrate its applicability in three representative RF circuits: a 30-GHz LC oscillator, a high-speed current-mode-logic (CML) frequency divider (FD), and a subthreshold Gb/s amplifier, all showing close agreement between simulated predictions and measurements performed at 4 and 2.5 K. Finally, we believe that the proposed approach is implementation-friendly and can significantly accelerate the development of cryo-CMOS integrated circuits.

circuit modeling↗

DOE OSTI2025

Lossy Compression: An Online Multi-Stage Technology for High-Fidelity Synchro- Waveform Measurements

Effective real-time monitoring and analysis of distributed grids necessitate the use of synchro-waveform measurements, which capture almost all high-frequency disturbances and transient phenomena. However, due to limitations in high-speed measurements and network bandwidth, it is challenging to transfer all high-fidelity synchro-waveforms losslessly and successfully. To cope with these challenges, a hybrid-based online multi-stage compression algorithm is proposed to significantly improve the compression efficiency for synchro-waveform measurements. Initially, the multiple discrete Wavelet transformation is deployed to deconstruct the waveform components. The delta encoding is further developed to decrease the magnitude. In conjunction with the Lempel-Ziv-Markov chain, the hybrid compression algorithm is implemented to achieve real-time compression for the synchro-waveform measurements. Moreover, an innovative error index that synergizes the time and frequency domain error and correlation is formulated to evaluate the waveform distortion. By integrating compression ratio, suitable parameters can be optimally selected. Finally, the simulation, laboratory experiments, as well as field tests across a spectrum of sampling frequencies and time intervals are conducted to substantiate the efficacy of the proposed method. Here, the outcomes demonstrated that a compression ratio of approximately 15.5 and 17.83 can be reached for 0.5 s and 1 s data under both offline and online scenarios, which equates to a substantial 93.5% to 94.39% reduction in data storage requirements.

High-fidelity synchro-waveform measurements↗

DOE OSTI2026

Data & Code from Phoenix CPPP Phase 2 Analysis

This data and code package supports the analysis presented in “Beyond Surface Cooling: Comprehensive Field Assessment of Reflective Pavement Thermal Performance in Phoenix, Arizona” and provides fully reproducible workflows for evaluating the thermal performance of cool pavement treatments in a hot urban environment. The dataset integrates multi-modal field measurements collected across residential and nonresidential settings, including mobile air temperature traverses, stationary air temperature monitoring, residential mean radiant temperature (MRT) measurements, subsurface temperature profiles, and controlled testbed observations. The data package contains raw and processed datasets in comma-separated value (CSV) format, accompanying metadata files describing site characteristics and measurement protocols, and R scripts (.R files) used for data cleaning, time synchronization, spatial and temporal matching, quality control filtering, statistical comparison, and figure generation. All analyses were conducted using R (version ≥ 4.2.0) with commonly available packages (e.g., tidyverse, lubridate, data.table, ggplot2). No proprietary software is required to reproduce results. Field campaigns were designed to quantify the effects of high-reflectance pavement coatings on surface temperature, near-surface air temperature, subsurface heat propagation, and radiative heat exposure. Temporal alignment procedures include standardized timestamp conversion and nearest-neighbor matching of high-frequency sensor measurements to stop-based metadata within defined tolerance windows to ensure comparability across instruments. The workflows generate summary statistics, treatment–control contrasts, depth-dependent thermal gradients, and time-series visualizations used in the associated publication. By integrating mobile, stationary, radiative, and subsurface measurements within a unified and transparent processing framework, this package enables comprehensive evaluation of cool pavement performance across multiple thermal exposure pathways and supports reuse in future urban heat mitigation and climate resilience studies.

AIR TEMPERATURE↗

DOE OSTI2025

Effect of Time Window and Spectral Measurement Options on Empirical Green’s Function Analysis Using DAS Array and Seismic Stations

The recorded seismic waveform is a convolution of event source term, path term, and station term. Removing high-frequency attenuation due to path effect is a challenging problem. Empirical Green’s function (EGF) method uses nearly collocated small earthquakes to correct the path and station terms for larger events recorded at the same station. However, this method is subject to variability due to many factors. Here, we focus on three events that were well recorded by the seismic network and a rapid response distributed acoustic sensing (DAS) array. Using a suite of high-quality EGF events, we assess the influence of time window, spectral measurement options, and types of data on the spectral ratio and relative source time function (RSTF) results. Increased number of tapers (from 2 to 16) tends to increase the measured corner frequency and reduce the source complexity. Extended long time window (e.g., 30 s) tends to produce larger variability of corner frequency. The multitaper algorithm that simultaneously optimizes both target and EGF spectra produces the most stable corner-frequency measurements. The stacked spectral ratio and RSTF from the DAS array are more stable than two nearby seismic stations, and are comparable to stacked results from the seismic network, suggesting that DAS array has strong potential in source characterization.

58 GEOSCIENCES↗

DOE OSTI2025

STILGAR End-of-Project Report

The Subsurface Tunnel Imaging LeveraGed by Analysis of Rayleigh wave ellipticity (STILGAR) project demonstrated an integrated geophysical approach for detecting, locating, and characterizing underground structural changes using dense seismic arrays and advanced inversion techniques. Field campaigns were conducted at two operational mines—the Redmond salt mine (Utah) and Graymont Pleasant Gap limestone mine (Pennsylvania)—providing real-world testbeds for monitoring anthropogenic subsurface activity. At the Redmond salt mine, seismic interferometry combined with back-projection inversion successfully identified continuous, low-amplitude signals from mining operations. The approach differentiated stationary from migrating anthropogenic sources, captured daily operational cycles, and validated the potential of passive seismic monitoring for remote detection of underground activity. At the Graymont Pleasant Gap mine, two dense seismic deployments in the spring and fall of 2023 generated over 4 TB of high-resolution data. Key outcomes included the relocation of 199 underground and 8 surface explosions with accuracies within tens of meters and the development of a 3D P-wave velocity model using the triple-difference tomography algorithm (tomoTD) that resolved major structural features such as the mine entrance, low-velocity tunnels, and roof-collapse areas. Ambient noise cross-correlation and back-projection analyses revealed persistent sources linked to ongoing mining activity, whereas horizontal-to-vertical spectral ratio (HVSR) and ellipticity studies confirmed stable site responses across seasons and identified soil thickness trends consistent with regional erosional and depositional processes. Checkerboard and sensitivity tests further validated the robustness of the tomographic results. Overall, the findings emphasize that although significant progress has been made in subsurface imaging, further work is needed to enhance the detection and localization of underground structures. Accurate imaging requires higher frequencies, yet anthropogenic sources tend to dominate the seismic record at those frequencies, and high-frequency surface waves are affected by higher modes that complicate interpretation. The improved detection and localization of human-induced signals enabled detailed temporal and spatial mapping of daily mine operations, demonstrating the feasibility of continuous anthropogenic source monitoring. Sensitivity to signals from nontraditional sources, such as fan operations, highlights the broader applicability of this approach to other industrial environments in which continuous and impulsive signals are present. The field campaigns produced a substantial volume of high-quality seismic data, supporting the development and testing of new methods for seismic source characterization and subsurface imaging. Future deployments should include sensors capable of recording lower frequencies to probe deeper structures, increase bandwidth to enhance resolution and sensitivity to both shallow and deep targets, and collect additional large-scale datasets to refine imaging and source characterization techniques. Moreover, conducting 3D modeling studies of seismic wavefields at higher frequencies will provide a better understanding of wave scattering and cavity–wavefield interactions in complex underground environments. In conclusion, the STILGAR project demonstrated that integrated seismic monitoring can effectively characterize underground operations, capturing both natural and anthropogenic signals. The approaches developed provide a foundation for improved detection, localization, and imaging of subsurface structures and are directly transferable to broader industrial monitoring applications.

58 GEOSCIENCES↗

DOE OSTI2025

Thermodynamic Profiling Through ASSIST Observations and TROPoe Retrievals

This report reviews the most relevant theoretical aspects of thermodynamic profiling techniques based on spectral observations from ASSIST-II infrared radiometers and TROPoe retrievals. The ASSIST+TROPoe system is a cutting-edge remote sensing technology deployed during the AWAKEN and WFIP3 field campaigns to estimate high-frequency profiles of temperature and humidity in the atmosphere. These profiles are highly valuable for characterizing atmospheric stratification, improving wind models, and understanding the impacts of wind plants on the climate. In this document, we discuss the operating principles of ASSIST, the physics of atmospheric infrared radiation, and the mathematical framework and capabilities of TROPoe. Sources of uncertainties in both the instrument and the retrieval method are also thoroughly addressed. This guide is designed to help users of ASSIST, TROPoe, and thermodynamic data in collecting, estimating, and applying thermodynamic profiles rigorously and scientifically.

17 WIND ENERGY↗

DOE OSTI2025

Novel Design and Fabrication of a High Frequency Transient Heat Flux Sensor for Use in an RDE

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than non-detonating engines. To understand the high-speed heat transfer dynamics inside an RDE, a novel, high-frequency heat flux gage is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Sensor bench testing is performed using a hot plate as a heat source, and the sensor response is compared to a finite-element analysis (FEA) model. The sensor response is then tested inside a water-cooled RDE and the wall heat flux is compared to calorimetry data.

rotating detonation engines↗

DOE OSTI2026

Red Noise–based False Alarm Thresholds for Astrophysical Periodograms via Whittle’s Approximation to the Likelihood

Astronomers who search for periodic signals using Lomb–Scargle periodograms rely on false alarm level (FAL) estimates to identify statistically significant peaks. Although FALs are often calculated from white noise models, many astronomical time series suffer from red noise. Prewhitening is a statistical technique in which a continuum model is subtracted from the log power spectrum estimate, after which the observer can proceed with a white-noise treatment. Here we present a prewhitening-based method of calculating frequency-dependent FALs. We fit power laws and autoregressive models of order 1 to each Lomb–Scargle periodogram by minimizing the Whittle approximation to the negative log-likelihood (NLL), then calculate FALs based on the best-fit model power spectrum. Our technique is a novel extension of the Whittle NLL to datasets with uneven time sampling. We demonstrate FAL calculations using observations of α Cen B, GJ 581, HD 192310, synthetic data from the radial velocity (RV) fitting challenge, and Kepler observations of a differential rotator. The Kepler data analysis shows that only true rotation signals are detected by red noise FALs, while white noise FALs suggest all spurious peaks in the low-frequency range are significant. A high-frequency sinusoid injected into α Cen B logR$'$ HK observations exceeds the 1% red noise FAL despite having only 8.9% of the power of the dominant rotation signal. In a periodogram of HD 192310 RVs, peaks associated with differential rotation and planets are detected against the 5% red noise FAL without iterative model fitting or subtraction. The software for calculating red noise–based FALs is available on GitHub.

Astrostatistics (1882)↗

NASA NTRS1969

Data processing method for a weak, moving telemetry signal

Method of processing data from a spacecraft, where the carrier has a low signal-to-noise ratio and wide unpredictable frequency shifts, consists of analogue recording of the noisy signal along with a high-frequency tone that is used as a clock to trigger a digitizer.

Kendall, W. B.↗

NASA NTRS1971

Magnetic materials selection for static inverter and converter transformers

Different magnetic alloys best suited for high-frequency and high-efficiency applications were comparatively investigated together with an investigation of each alloy's inherent characteristics. One of the characteristics in magnetic materials deterimental in transformer design is the residual flux density, which can be additive on turn-on and cause the transformer to saturate. Investigation of this problem led to the design of a transformer with a very low residual flux. Tests were performed to determine the dc and ac magnetic properties at 2400 Hz using square-wave excitation. These tests were performed on uncut cores, which were then cut for comparison of the gapped and ungapped magnetic properties. The optimum transformer was found to be that with the lowest residual flux and a small amount of air gap in the magnetic material. The data obtained from these tests are described, and the potential uses for the materials are discussed.

Mclyman, C. W. T.↗

NASA NTRS1972

Dynamic response of high-frequency pressure transducers to large amplitude sinusoidal pressure oscillations

Dynamic response characteristics of six currently used dynamic pressure transducers were investigated by using a large-amplitude sinusoidal-pressure generator. Frequencies between 1 and 15 kilohertz with corresponding peak-to-peak pressure-oscillation amplitudes ranging between 73 and 8 percent of bias pressure and bias pressures between 15 and 300 psia were utilized. Amplitude-ratio data as functions of frequency and pressure level are given for all transducers. The generator design and performance and associated instrumentation are described.

Robinson, R. E.↗

NASA NTRS1973

Magnetic materials selection for static inverter and converter transformers

A program to study magnetic materials is described for use in spacecraft transformers used in static inverters, converters, and transformer-rectifier supplies. Different magnetic alloys best suited for high-frequency and high-efficiency applications were comparatively investigated together with an investigation of each alloy's inherent characteristics. The materials evaluated were the magnetic alloys: (1) 50% Ni, 50% Fe; (2) 79% Ni, 17% Fe, 4% Mo; (3) 48% Ni, 52% Fe; (4) 78% Ni, 17% Fe, 5% Mo; and (5) 3% Si, 97% Fe. Investigations led to the design of a transformer with a very low residual flux. Tests were performed to determine the dc and ac magnetic properties at 2400 Hz using square-wave excitation. These tests were performed on uncut cores, which were then cut for comparison of the gapped and ungapped magnetic properties. When the data of many transformers in many configurations were compiled the optimum transformer was found to be that with the lowest residual flux and a small amount of air gap in the magnetic material. The data obtained from these tests are described, and the potential uses for the materials are discussed.

Mclyman, W. T.↗

NASA NTRS1974

In situ measurements of the spectral characteristics of F region ionospheric irregularities

The retarding potential analyzer aboard Ogo 6 has provided high-resolution observations of the ion concentration along the satellite path. Changes in ion concentration as small as 0.03% and at times as small as 0.01% could be measured. Spatial resolution varied from 35 to 380 m. Samples of data have been analyzed to determine the spectral properties of the F region irregularities observed. The most common frequency spectrum observed suggests that the responsible irregularities result from the turbulent dissipation of larger irregularities. At the equator, the larger irregularities are probably produced by convective electric fields. At high latitudes, electric fields may also be involved, but other factors such as precipitating particles may contribute to, or be primarily responsible for, the production of large irregularities. Examples of other types of spectra associated with wavelike irregularities and with 'ground glass' (high-frequency noise) irregularities are also shown.

Dyson, P. L.↗

NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗

NASA NTRS1974

Spectral behavior of Jupiter near 1 MHz

Emission from Jupiter has been observed by the IMP-6 spacecraft at 25 frequencies between 425 and 9900 kHz covering the period April 1971 to October 1972. The Jovian bursts were identified through the phase of the observed modulated signal detected from the spinning dipole antenna. Approximately 500 days of data have been scanned for Jupiter emissions with a positive detection of at least 382 events. The static spectral behavior of the emission has been investigated and can be divided naturally into three types. Type one (normal) shows a high correlation with earth-based observations and follows the same spectral behavior. These bursts are seldom detected much below 1 MHz. The second type (md-frequency) occurs near or below 1 MHz and shows low and high-frequency cutoffs. The emission peak is near 900 kHz with a 3 db bandwidth of approximately 450 kHz. A third type consists of a complex combination of the previous types.

Brown, L. W.↗

NASA NTRS1975

Acoustic characteristics of a large upper-surface blown configuration with turbofan engines

This paper presents acoustic results from static and simulated low forward velocity tests of a large-scale model of an aircraft configuration with two turbofan engines in the full-scale tunnel at the Langley Research Center. The turbofan engines were integrated into the model and equipped with rectangular nozzles to provide the upper-surface blowing. Results indicate that the upper-surface-blowing noise problem can be characterized, primarily, by the unsymmetrical radiation pattern due mainly to shielding of the high-frequency engine noise and the production of low-frequency noise by jet-surface interaction. The directivity of the low-frequency noise was found to depend on the trailing-edge flap angle when the thrust levels were low. Normalized sound pressure level spectral density data showed good agreement at low Strouhal number with other small- and large-scale model data from tests using simulated wing-flap systems. Forward speed effects were undetectable at the low tunnel speeds used during the tests.

Preisser, J. S.↗

NASA NTRS1976

Recent decametric and hectometric observations of Jupiter

Observational results on Jupiter's high-frequency radiation, for the range 1-35 MHz (10 to 100 m), obtained over the past six years with the aid of orbited telescopes, are surveyed. Spectral distributions, periodic effects, burst waveforms and dynamic spectra of storms, polarization effects, high-resolution interferometry, and possible correlations with solar activity are discussed. Related spacecraft experiments are described. Close attention is given to long-term accumulation of occurrence probability data as functions of time and frequency (synoptic monitoring) on Jovian HF emission, and to dominating effects of the Jovian satellite Io, as well as modulation of periodicities by the 11.9-year orbital motion period of Jupiter. Possible effects of the other four Jovian satellites immersed in the Jovian magnetosphere are also taken into consideration. Absence of a Jovian Faraday effect and polarization of fine burst structure are discussed.

Carr, T. D.↗

NASA NTRS1980

Synthetic aperture radar imaging of ocean waves - Comparison with wave measurements

Synthetic aperture radar images of ocean waves were obtained in conjunction with reference wave data near Marineland, Florida, December 14, 1975. Each of the various types of measurements were processed into a form that allowed direct comparisons with the others. Maxima of radar spectra occurred at the same frequencies as the maxima of reference wave height spectra. In a comparison of a radar spectrum with observed spectra of wave height, wave orbital velocity, and surface slope the high-frequency portion of the radar spectrum lay near and between the wave height and the orbital velocity spectra but differed significantly from the surface slope spectrum. The radar-derived mean directions and model-fitted directional spreads of wave energy were close to the values from a directional wave buoy and indicated the accuracy of radar measurements of wave direction. However, a directional plot of a radar spectrum near shore at the frequency of the maximum showed a sharper peak than such a plot of a fitted spectrum derived from reference data.

Mcleish, W.↗