Search NASASearch

SEARCH · Search NASA

Results for “injection height”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

High Earth orbit design for lunar assisted small Explorer class missions

Small Expendable launch vehicles are capable of injecting modest payloads into high Earth orbits having apogee near the lunar distance. However, lunar and solar perturbations can quickly lower perigee and cause premature reentry. Costly perigee raising maneuvers by the spacecraft are required to maintain the orbit. In addition, the range of inclinations achievable is limited to those of launch sites unless costly spacecraft maneuvers are performed. This study investigates the use of a lunar swingby in a near-Hohmann transfer trajectory to raise perigee into the 8 to 25 solar radius range and reach a wide variety of inclinations without spacecraft maneuvers. It is found that extremely stable orbits can be obtained if the postencounter spacecraft orbital period is one-half of a lunar sidereal revolution and the Earth-vehicle-Moon geometry is within a specified range. Criteria for achieving stable orbits with various perigee heights and ecliptic inclinations are developed, and the sensitivity of the resulting mission orbits to transfer trajectory injection (TTI) errors is examined. It is shown that carefully designed orbits yield lifetimes of several years, with excellent ground station coverage characteristics and minimal eclipses. A phasing loop error correction strategy is considered with the spacecraft propulsion system delta V demand for TTI error correction and a postlunar encounter apogee trim maneuver typically in the 30 to 120 meters per second range.

Mathews, M.

Reply to Comment by Cole-dai Et Al. on "Climatic Impact of the Long-lasting Laki Eruption: Inapplicability of Mass-independent Sulfur Isotope Composition Measurements"

Here we respond to the comments by Cole-Dai et al. [2014] on our article Schmidt et al. [2012]. Specifically, in response to section 2 of their reply, we argued in Schmidt et al. [2012] that based on previously published estimates of the volatile release height during the 1783-1784 C.E. Laki eruption, the lack of a sulfur massindependent fractionation (MIF) anomaly is expected. In other words, no previous study on Laki ever argued that this eruption emitted SO2 into altitudes >13-15 km. In section 2.3, Cole-Dai et al. [2014] argue that the nonzero Δ33S value of their Laki sample 1 may be explained by a short-lived explosive phase at Laki during which volatiles reached the stratosphere. In Schmidt et al. [2012] in section 2, we argued in agreement with Cole-Dai et al. [2014] (section 3.1) that for a MIF anomaly to be preserved, the Laki volatiles would have had to be emitted in >20 km altitude. Our main point is that eruption column heights >20 km are unlikely based on the historical accounts and plume-rise modeling for the Laki eruption [Stothers et al., 1986; Woods, 1993; Thordarson and Self, 2003]. In Schmidt et al. [2012], we argued that to deduce a short-lived climatic impact of the Laki eruption based on the lack of a MIF anomaly and the length of the sulfate deposition in Greenland ice cores may be misleading because the climatic impact will outlast the radiative forcing of the Laki aerosol cloud. Cole-Dai et al. [2014] acknowledge the latter in their reply in section 4.2. We agreewith Cole-Dai et al. [2014] in that themagnitude and length of the climatic impact during the winter of 1783-1784 depends on the altitude of the volatile release during the eruption (sections 2.3 and 4.2). However, even if we assumed that during Laki all sulfur dioxide (SO2) would have been released in the troposphere, then the aerosol cloud would still be present in the upper troposphere during March 1784, as is evident from independent model simulations of this "tropospheric-only" scenario [Stevenson et al., 2003]. We acknowledge that there is uncertainty on the volatile release height for Laki; however, it is worth considering that those climate model simulations that used an injection altitude between 9 km and 13 km for the Laki SO2 [Highwood and Stevenson, 2003; Oman et al., 2006a, 2006b; Schmidt et al., 2012] best match the observed temperature changes during summer of 1783 [Angell and Korshover, 1985; Brázdil et al., 2010; Briffa et al., 1998; D'Arrigo and Jacoby, 1999; Jacoby et al., 1999; Kington, 1988; Manley, 1974; Parker et al., 1992; Thordarson and Self, 2003]. Based on these model simulations, a climatic impact during the winter of 1783-1784, albeit weaker than during the climactic phases of Laki, is expected (and our argument here does not exclude the role of natural variability in contributing to the cold winter of 1783-1784 as discussed in Schmidt et al. [2012]). Therefore, we continue to argue that for high-latitude eruptions such as Laki, the applicability of sulfur isotopic measurements to interpret the climatic relevance has yet to be demonstrated. Itmay transpire that the interpretation of MIF signals for the climate-relevance of an eruption is valid and unambiguous only for short-lived explosive eruptions in the tropics. In terms of the processes producing a MIF anomaly (section 3.3 in Cole-Dai et al. [2014]), the works by Hattori et al. [2013] and Ono et al. [2013] suggest that there are remaining issues not discussed by Cole-Dai et al. [2014], for instance, self-shielding of SO2 due to high column densities typical for eruptions of Pinatubo-scale and greater, and the preservation of the MIF signature in general.

general circulation model

System engineering study of electrodynamic tether as a spaceborne generator and radiator of electromagnetic waves in the ULF/ELF frequency band

The transmission and generation by orbiting tethered satellite systems of information carrying electromagnetic waves in the ULF/ELF frequency band to the Earth at suitably high signal intensities was examined and the system maintaining these intensities in their orbits for long periods of time without excessive onboard power requirements was investigated. The injection quantity power into electromagnetic waves as a function of system parameters such as tether length and orbital height was estimated. The basic equations needed to evaluate alternataing current tethered systems for external energy requirements are presented. The energy equations to tethered systems with various lengths, tether resistances, and radiation resistances, operating at different current values are applied. Radiation resistance as a function of tether length and orbital height is discussed. It is found that ULF/ELF continuously radiating systems could be maintained in orbit with moderate power requirements. The effect of tether length on the power going into electromagnetic waves and whether a single or dual tether system is preferable for the self-driven mode is discussed. It is concluded that the single tether system is preferable over the dual system.

Estes, R. D.

Magnetosphere-Regolith/Exosphere Coupling: Differences and Similarities to the Earth Magnetosphere-Ionosphere Coupling

Of the three Mercury passes made by Mariner 10, the first and third went through the Mercury magnetosphere. The third encounter which occurred during northward IMF (interplanetary magnetic field) showed quiet time magnetic fields. In contrast the third encounter observed clear substorm signatures including dipolarization, field-aligned currents (FACs) and injection of energetic electrons at geosynchronous orbit. However, the determined cross-tail potential drop and the assumed height integrated conductance indicate that the FAC should be 2-50 times weaker than observed. We address this inconsistency and the fundamental problem of FAC closure whether this takes place in the regolith or in the exosphere. The current state of knowledge of the magnetosphere-exosphere/regolith coupling is addressed and similarities and differences to the Earth magnetosphere-ionosphere coupling are discussed.

Gjerleov, J. W.

Explosive Volcanic Eruptions from Linear Vents on Earth, Venus and Mars: Comparisons with Circular Vent Eruptions

Conditions required to support buoyant convective plumes are investigated for explosive volcanic eruptions from circular and linear vents on Earth, Venus, and Mars. Vent geometry (linear versus circular) plays a significant role in the ability of an explosive eruption to sustain a buoyant plume. On Earth, linear and circular vent eruptions are both capable of driving buoyant plumes to equivalent maximum rise heights, however, linear vent plumes are more sensitive to vent size. For analogous mass eruption rates, linear vent plumes surpass circular vent plumes in entrainment efficiency approximately when L(sub o) > 3r(sub o) owing to the larger entrainment area relative to the control volume. Relative to circular vents, linear vents on Venus favor column collapse and the formation of pyroclastic flows because the range of conditions required to establish and sustain buoyancy is narrow. When buoyancy can be sustained, however, maximum plume heights exceed those from circular vents. For current atmospheric conditions on Mars, linear vent eruptions are capable of injecting volcanic material slightly higher than analogous circular vent eruptions. However, both geometries are more likely to produce pyroclastic fountains, as opposed to convective plumes, owing to the low density atmosphere. Due to the atmospheric density profile and water content on Earth, explosive eruptions enjoy favorable conditions for producing sustained buoyant columns, while pyroclastic flows would be relatively more prevalent on Venus and Mars. These results have implications for the injection and dispersal of particulates into the planetary atmosphere and the ability to interpret the geologic record of planetary volcanism.

Glaze, Lori S.

Fast magnetospheric echoes of energetic electron beams

Electron beam experiments using rocketborne instrumentation have confirmed earlier observations of fast magnetospheric echoes of artificially injected energetic electrons. A total of 234 echoes have been observed in a pitch angle range from 9 to 110 deg at energies of 1.87 and 3.90 keV. Out of this number, 95 echoes could unambiguously be identified with known accelerator operations at 2-, 4-, or 8-keV energy and highest current levels resulting in the determination of transit times of typically 300 to 400 ms. In most cases, when echoes were present in both energy channels, the higher-energy electrons led the lower-energy ones by 50 to 70 ms. Adiabatic theory applied to these observations yields a reflection height of 3000 to 4000 km. An alternative interpretation is briefly examined, and its relative merit in describing the observations is evaluated. The injection process is discussed in some detail as the strong beam-plasma interaction that occurred near the electron accelerator appears to be instrumental in generating the source of heated electrons required for successful echo detection for both processes.

Wilhelm, K.

Remote sounding through semi-transparent cirrus cloud

A large portion of the earth is covered by thin semi-transparent cirrus cloud. The cirrus results from the natural injection of moisture into the upper troposphere by deep convection (i.e., anvils) and from man-made moisture injected into the upper troposphere by jet aircraft. Although most cirrus clouds are semi-transparent to infrared wavelengths, their heights, thicknesses, and spectral absorption properties must be known in order to retrieve atmospheric temperature and moisture profiles from the data. An algorithm is developed for accounting for the radiative properties of semi-transparent cloud in the retrieval of vertical temperature and moisture profiles. The algorithm is to be applied to the NASA ER2 HIS data collected during the FIRE cirrus field program.

Smith, William L.

The effect of entrance radius and film injection on wall heating in scramjet nozzles

An experimental study has been performed with a scramjet combustor and nozzle model to determine the effect of nozzle radii on relaminarization, and the effectiveness of film injection in reducing wall heat flux. The nozzle model was installed downstream of a swept-ramp scramjet combustor model, operated at Mach 2.7 with vitiated air, simulating Mach 6-7 flight enthalpies. Results from tests conducted with three nozzle radii, varying in curvature from a sharp Prandtl-Meyer expansion to a radius of two scramjet combustor exit heights, showed little or no effect on the downstream wall heat flux, which is not in agreement with both subsonic and supersonic relaminarization correlations in the available literature. In contrast, film injection upstream of all three radii produced reductions of 70 percent in the entire nozzle model heating rate, for the nominal film-to-free stream pressure matched condition. Results from film injection, with and without pressure gradient, but without wall curvature, show that the gradients appear to stabilize the film, with the resulting reductions in wall heat transfer rates apparent far downstream of the point of injection.

Baker, N. R.

A new technique for inducing a turbulent boundary layer in a supersonic flow

The feasibility of using slot injection to establish a turbulent boundary layer corresponding to a known Reynolds number is experimentally investigated. The basic concept consists of injecting secondary air through a slot. The air is injected at the same local static pressure and at a selected stagnation temperature to simulate a given upstream condition. The mass of the injected air can be controlled to match a desired Reynolds number. In the present experiment, secondary air was injected through a supersonic nozzle over a flat plate model. Heat transfer rates were measured at about 50 to 100 slot heights behind the slot, and the results were compared with theoretical estimates. Static pressure measurements were made over the surface in the streamwise direction. Velocity and Mach number profiles were obtained at a selected position downstream of the slot. Laminar and turbulent profiles were calculated from the Crocco method and the 1/7 power law respectively to compare with the results of measurements.

Miyazawa, M.

VLA-BATSE observations of an intense solar decimetric and hard X-ray burst

We discuss observations of a multiply impulsive solar burst that was detected simultaneously by the VLA at 20 and 90 cm and by the Burst and Transient Experiment (BATSE) at hard X-ray wavelengths. The flare-associated 20 cm emission consists of two groups of bursts about 4 min apart. Hard X-ray emission above 25 keV was detected during both groups of bursts, while 90 cm bursts occurred only during the second and more intense group. VLA snapshot maps at intervals of 1.7 s reveal that the 20 cm burst originates within a relatively compact source located above the east limb at a height of roughly 1.8 x 10 exp 10 cm. The 90 cm burst is more extended and lies at a height of roughly 2.2 x 10 exp 10 cm. The similarity of the time profiles in the two spectral domains suggests a common injection of energetic electrons, while the time delays are consistent with the travel times of electrons which propagate from the chromosphere to the sites of the coronal radio bursts. We find that the VLA emission is probably the type III or type IV radiation of electrons trapped in large coronal loops, and that plasma radiation, rather than gyrosynchrotron emission, can explain it.

Willson, Robert F.

Sensitivity of engine-integrated waverider performance to static margin constraint

The performance of an engine-integrated wedge caret-wing waverider is optimized with respect to a set of geometric and flight attitude variables with constraints for steady state flight and static margin. The optimization is done with different values for the constraint on the static margin, and the resulting performances and geometries compared. This comparison is done for three performance parameters: L/D ratio, range coefficient, and a parameter that measures energy height gain per unit weight of fuel. The vehicle model incorporates a one-dimensional calculation on the forebody, inlet and wings. Fuel injection is done prior to the combustor entrance and flow properties are calculated with a one-dimensional model using a correlation for the shock shape in front of a transverse jet. The combustor is modeled as a shock-induced-combustion scramjet, and the nozzle flow field is calculated using the method of characteristics.

Tarpley, C.

Constraints on the Galactic Halo Dark Matter from Fermi-LAT Diffuse Measurements

We have performed an analysis of the diffuse gamma-ray emission with the Fermi Large Area Telescope (LAT) in the Milky Way halo region, searching for a signal from dark matter annihilation or decay. In the absence of a robust dark matter signal, constraints are presented. We consider both gamma rays produced directly in the dark matter annihilation/decay and produced by inverse Compton scattering of the e+/e− produced in the annihilation/decay. Conservative limits are derived requiring that the dark matter signal does not exceed the observed diffuse gamma-ray emission. A second set of more stringent limits is derived based on modeling the foreground astrophysical diffuse emission using the GALPROP code. Uncertainties in the height of the diffusive cosmic-ray halo, the distribution of the cosmic-ray sources in the Galaxy, the index of the injection cosmic-ray electron spectrum, and the column density of the interstellar gas are taken into account using a profile likelihood formalism, while the parameters governing the cosmic-ray propagation have been derived from fits to local cosmic-ray data. The resulting limits impact the range of particle masses over which dark matter thermal production in the early universe is possible, and challenge the interpretation of the PAMELA/Fermi-LAT cosmic ray anomalies as the annihilation of dark matter.

DIFFUSE MEASUREMENTS

Mass loss from S stars

The mass-loss process in S stars is studied using 65 S stars from the listing of Wing and Yorka (1977). The role of pulsations in the mass-loss process is examined. It is detected that stars with larger mass-loss rates have a greater amplitude of pulsations. The dust-to-gas ratio for the S stars is estimated as 0.002 and the average mass-loss rate is about 6 x 10 to the -8th solar masses/yr. Some of the properties of the S stars, such as scale height, surface density, and lifetime, are measured. It is determined that scale height is 200 pc; the total duration of the S star phase is greater than or equal to 30,000 yr; and the stars inject 3 x 10 to the -6th solar masses/sq kpc yr into the interstellar medium.

Jura, M.

Supersonic burning in separated flow regions

The trough vortex phenomena is used for combustion of hydrogen in a supersonic air stream. This was done in small sizes suitable for igniters in supersonic combustion ramjets so long as the boundary layer displacement thickness is less than 25% of the trough step height. A simple electric spark, properly positioned, ignites the hydrogen in the trough corner. The resulting flame is self sustaining and reignitable. Hydrogen can be injected at the base wall or immediately upstream of the trough. The hydrogen is introduced at low velocity to permit it to be drawn into the corner vortex system and thus experience a long residence time in the combustion region. The igniters can be placed on a skewed back step for angles at least up to 30 deg. without affecting the igniter performance significantly. Certain metals (platinum, copper) act catalytically to improve ignition.

Zumwalt, G. W.

Buoyancy Effects in Strongly-pulsed, Turbulent Diffusion Flames

The objective of this experiment is to better understand the combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. The fuel jet is fully-modulated (i.e., completely shut off between pulses) by an externally controlled valve system leading to enhanced fuel/air mixing compared to acoustically excited or partially-modulated jets. Experiments are conducted both in laboratories at UW and WPI and in the GRC 2.2s Drop Tower. A single fuel nozzle with diameter d = 2 mm is centered in a combustor 20 x 20 cm in cross section and 67 cm in height. The gaseous fuel flow (ethylene or a 50/50 ethylene/nitrogen mixture by volume) is fully-modulated by a fast-response solenoid valve with injection times from tau = 4 to tau = 300 ms. The nominal Reynolds number based on the fuel velocity during injection, U(sub jet), is 5,000. A slow oxidizer co-flow properly ventilates the flame and an electrically heated wire loop serves as a continuous ignition source. Diagnostic techniques include video imaging, fine-wire thermocouples and thermopile radiometers, and gas sampling and standard emissions instruments (the last in the laboratory only).

Hermanson, J. C.

Buoyancy Effects in Strongly-Pulsed, Turbulent Diffusion Flames

The objective of this experiment is to better understand the combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. The fuel jet is fully-modulated (i.e., completely shut off between pulses) by an externally controlled valve system leading to enhanced fuel/air mixing compared to acoustically excited or partially-modulated jets. Experiments are conducted both in laboratories at UW and WPI and in the GRC 2.2s Drop Tower. A single fuel nozzle with diameter d = 2 mm is centered in a combustor 20 20 cm in cross section and 67 cm in height. The gaseous fuel flow (ethylene or a 50/50 ethylene/nitrogen mixture by volume) is fully-modulated by a fast-response solenoid valve with injection times from tau = 4 to tau = 300 ms. The nominal Reynolds number based on the fuel velocity during injection, U(sub jet), is 5,000. A slow oxidizer co-flow properly ventilates the flame and an electrically heated wire loop serves as a continuous ignition source. Diagnostic techniques include video imaging, fine-wire thermocouples and thermopile radiometers, and gas sampling and standard emissions instruments (the last in the laboratory only).

Hermanson, J. C.

Ballistic range experiments on superbooms generated by refraction

The enhanced sonic boom or supersonic boom generated as a result of atmospheric refraction in threshold Mach number flights was recreated in a ballistic range by firing projectiles at low supersonic speeds into a stratified medium obtained by slowly injecting carbon dioxide into air. The range was equipped with a fast-response dynamic pressure transducer and schlieren photographic equipment, and the sound speed variation with height was controlled by regulating the flow rate of the CO2. The schlieren observations of the resulting flow field indicate that the generated shocks are reflected near the sonic cutoff altitude where local sound speed equals body speed, provided such an altitude exists. Maximum shock strength occurs very nearly at the point where the incident and reflected shocks join, indicating that the presence of the reflected shock may have an appreciable effect on the magnitude of the focus factor. The largest focus factor detected was 1.7 and leads to an estimate that the constant in the Guiraud-Thery scaling law should have a value of 1.30.

Sanai, M.

Effect on Gaseous Film Cooling of Coolant Injection Through Angled Slots and Normal Holes

A study was made to determine the effect of coolant injection angularity on gaseous film-cooling effectiveness. In the correlation of experimental data an effective injection angle was defined by a vector summation of the coolant and mainstream gas flows. The cosine of this angle was used as a parameter to empirically develop a corrective term to qualify a correlating equation presented in Technical Note D-130 that was limited to tangential injection of the coolant. Data were also obtained for coolant injection through rows of holes normal to the test plate. The slot correlating equation was adapted to fit these data by the definition of an effective slot height. An additional corrective term was then determined to correlate these data.

Papell, S. Stephen